Muxlab Passive CCTV Hub Plus User Manual

Passive CCTV Hub Plus (500134)

Installation Guide

P/N: 94-000690-A, SE-000690-A

Pag

Printed in Canada. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without prior written permission of the author.

Trademarks :

MuxLab is a registered trademark of MuxLab Inc.

e 2

Pag

Table of Contents

1. Overview ...................................................................................................................4

1.1. Description........................................................................................................4

1.2. Features.............................................................................................................4

2. Technical Specifications...........................................................................................5

3. Installation Procedure..............................................................................................6

3.1. Parts List ...........................................................................................................6

3.2. Product Overview .............................................................................................6

3.3. Pre-Installation Checklist .................................................................................7

3.4. Physical Installation..........................................................................................8

3.5. Installation Procedure .......................................................................................9

4. Troubleshooting......................................................................................................18

5. Distance Tables.......................................................................................................19

6. Product Warranty Policy.......................................................................................21

e 3

Pag

Overview

1.1. Description

The Passive CCTV Hub Plus (500134) allows video, remote power and PTZ control to be transmitted via one Cat5e/6 cable, thus eliminating the need to install multiple cables for more efficient cabling in the security video environment. The hub features a detachable, factory-installed, 16-channel power cable assembly that allows the hub to be connected to a 16-channel CCTV power supply for greater ease of installation. In order to connect remote power to the hub, the 16-channel power cable assembly included with the hub must be used.

The Passive CCTV Hub Plus works in conjunction with MuxLab’s 500000, 500009, 500015, 500022, 500023, 500024, 500029, 500120, 500122 and

500130. The product features a port switch to set the unit to Power-Thru or Pass-Thru mode.

1.2. Features

• Port switch to set unit to Pass-Thru Mode (500022) or Power-Thru Mode

(500024/500029)

• Includes 16-channel power cable assembly (packaged seperately)

• Pin configuration chart on unit

• Space efficient, rack-mountable

e 4

Pag

Technical Specifications

Specifications

Environment Devices Transmission

Video

Bandwidth Maximum Input Insertion Loss Return Loss Common Mode Rejection Max. Distance - Color

Max. Distance - B&W

Remote Power

Switch Mode Pass-Thru Mode (500022) Power-Thru Mode (500024/500029) Number of twisted pairs Max. Distance @ 24VAC*

*Based on 10% voltage drop at camera. Longer distances may be achieved @ 28 VAC.

Maximum Input Voltage

Maximum Current Rating

2-Wire PTZ Control (i.e. RS-422, Manchester/Bi-Phase, half duplex RS485) – Pass-Thru Mode (500022)

Wiring

Maximum Distance

Maximum Power Rating

Mechanical & Environmental

Cable – UTP

Cable – Coax

Connectors

Port Configuration Switch

RJ45 Pin Configuration* Signal 500022 Mode 500024/500029 Mode

*Reverse polarity sensitive

Temperature

Enclosure

Dimensions

Weight

Warranty

Order Information

Composite video; NTSC, PAL, SECAM CCTV cameras, DVRs, monitors, switchers, multiplexers and other CCTV equip. Transparent to the user.

DC to 8 MHz.

1.1Vp-p Less than 2 dB per pair over the frequency range from DC to 8 MHz Greater than 15 dB over the frequency range from DC to 8 MHz Greater than 40 dB @ 8 MHz Cat 3 –1,200 ft (365m); Cat5e/6 – 2,200 ft. (670m)*

*Shorter distances will result with DVR equipment. Typically 1,000 to 1,500 ft

Cat 3 –1,500 ft (457m); Cat5e/6 – 2,500 ft (762m)

Two (2) Three (3) 5 VA: 350 ft (107m) 10 VA: 175 ft

(53m)

20 VA: 90 ft (30m) 30 VA: 60 ft (20m)

50 Volts (AC RMS/DC). Recommended Class II PSU with fuse protection per port

4.5A (AC RMS/DC)

Remote 2-wire PTZ control supported via one (1) twisted pair. Up to 4,000 ft (1.2 km) depending on the PTZ camera vendor**

**Please consult your CCTV equipment vendor for more detailed performance

specifications.

50 Volts (AC RMS/DC); 3A (AC RMS/DC)

24 AWG or lower solid copper twisted pair wire impedance: 100 ohms at 1 MHz Maximum capacitance: 20 pf/foot. Attenuation: 6.6 dB/1000 ft at 1 MHz

Impedance: 75 Ω at 1 MHz. (RG59/U). Max. 25 ft. of coax allowed end to end. Video (Model 500130): Sixteen (16) BNC-F

Power: Sixteen (16) 2-pole screw terminals. Control: Sixteen (16) 2-pole screw terminals.

16-channel factory-installed 24” (61cm) detachable 4-pole connector power

cable assembly included.

Combined signals: Sixteen (16) RJ45 jacks Sets each port to Pass-Thru Mode (500022) or Power-Thru Mode (500024/500029)

Power A (+) 1, 3 1, 3, 5 Power B (-) 2, 6 2, 4, 6 Control (+) 4 Not used Control (-) 5 Not used Video BNC Center (Tip) 7 [T] opposite to 500000 7 [T] opposite to 500000 Video BNC Ground (Ring) 8 [R] opposite to 500000 8 [R] opposite to 500000 Operating: 0° to 55°C. Storage:-20° to 85°C. Humidity: up to 95% Black, anodized aluminum 19” (48.26 cm) W x 1.75” (4.4 cm) H x 2.0” ( 5.1 cm) D

2.6 lbs. (1.2kgs) Lifetime 500134 Passive CCTV Hub Plus

5 VA: 518 ft (170m) 10 VA: 259 ft (85

20 VA: 130 ft (43 m) 30 VA: 86 ft (28 m)

e 5

Pag

Installation Procedure

3.1. Parts List

The Passive CCTV Hub Plus comes with the following parts. Please verify that all pieces are present before proceeding.

• Base Unit (Factory configuration: Power-Thru Mode (500022)

• 16-channel power cable assembly.

• Installation Guide

3.2. Product Overview

The external connections of the Passive CCTV Hub Plus are detailed in the following diagrams. Please familiarize yourself with them before installing the unit.

Figure 1: Front panel

Figure 2: Rear panel

e 6

+ 14 hidden pages

Muxlab Passive CCTV Hub Plus User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual