Muxlab LongReach CCTV IP PoE Extender Kit, 30W User Manual

© MuxLab Inc.

94-000758-A

SE-000758-A

© MuxLab Inc. 2014

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: [phone] Fax: [phone]

Toll Free (North America): [phone]

E-mail: [e-mail] URL: www.muxlab.com

Specifications

Environment

PoE CCTV IP

Devices

PoE CCTV IP cameras with a 10/100Mb/s Ethernet port, using up to
30 Watts.

Transmission

Transparent to the user

Standard supported

Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX
IEEE 802.3at compatible PoE

PoE Power

Class 3

Connectors

One (1) BNC 75 Ohms.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.

LED Indicators

Power, IP Traffic, 100MBps

Maximum Distance

RG59/RG6: Up to 980 ft (300m) @ 100Mbps
UTP Cat 5e/6: Up to 330 ft (100 m)

Note: When installed in an electrically noisy environment, an STP
cable must be used. Also, cross-connection reduces the effective
distance depending on the grade of twisted cable used.

RJ45 Pin
Configuration

Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight­through wiring.

RJ45 Link

Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)

Cable

UTP/STP: One (1) Cat 5e/6 or better twisted pair cables required
RG59/RG6: 75 Ohms (avoid CCS cable)

Power Supply

Optional Power Supply (110-240V/56VDC) minimum 40W.

Required at the Camera Side Device when coax cable quality or
length results in insufficient power reaching the camera. Required
at the Network Side Device when used with non-PoE environment.

Power Consumption

Network Side: 1.82 Watt Camera Side: 1.73 Watt

Temperature

Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing

Enclosure

Metal

Accessories

Wall-mount brackets included

Dimensions

4.37” x 2.95” x 0.99” (110 x 75 x 25 mm)

Weight

1.5 lb (0.68 kg)

Compliance

Regulatory: FCC, CE, RoHS Flammability: 94V0

Warranty

2 years

Order Information

500112-30W CCTV IP PoE Extender Kit, 30W

LongReach CCTV IP PoE

Extender Kit, 30W

500112-30W

Quick Installation Guide

Overview
The LongReach CCTV IP PoE Extender Kit, 30W (500112-30W) allows one IP camera
(30 Watts) to be connected up to 980 ft (300 m) via a single 75-ohm coax cable in a
point-to-point configuration. The maximum distance depends on the grade and quality
of coaxial cable. An optional 48-56VDC (40W) Power Supply can be used if required.

Applications

CCTV IP surveillance

Installation

1. Identify the connectors on the Extenders as indicated on the product labels.

2. Attach the surface-mount brackets if required as shown below.

© MuxLab Inc. 2014

© MuxLab Inc. 2014

3. Verify that the distance between the CCTV IP PoE extenders is within MuxLab

Symptom

Network Side

LEDs

Camera Side

LEDs

Probable Cause

Possible

Solutions

Power

IP Traffic

Power

IP Traffic

No Image

OFF

OFF

OFF

OFF

No power

• Check if the Ethernet
switch is PoE.

• Check the power
connection.

No Image

ON

OFF

OFF

OFF

Coaxial Cable

• Check the coaxial
cables.

No Image

ON

OFF

OFF

OFF

Distance

• Check the coaxial
cables length and
quality.

No Image

ON

OFF

ON

OFF

UTP Cable

• Check the UTP Cable
pin out.

No Image

ON

ON

ON

ON

No Traffic

• Check network
configuration.

Choppy Image

ON

BLINK

ON

BLINK

Distance

• Check cable length

• Check the coaxial

cable quality.

specifications (see Specifications table).

4. To install the Network Side Device:

4a. Connect the extender to the PoE Ethernet Switch with a UTP Cable.

Note: If the Ethernet Switch is not PoE; you will need to connect a 56VDC
(40W) Power Supply to the Network Side Device.

4b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX

LINK connector on the Extender.

5. To install the Camera Side Device:

5a. Connect the extender to the camera with a Cat5e/6 cable.

Note: If the quality or length of the coaxial cable reduces the power to a level
that is insufficient to power the camera, you will need to connect a 48-56VDC
(40W) Power Supply to the Camera Side device.

5b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX

LINK connector on the Extender.

6. Power on the equipment and verify the image quality. The following is a diagram

of a typical configuration.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions
in respect to the installation of the LongReach CCTV IP PoE Extender Kit, 30W:

Tables

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or ([phone] (International).