Muxlab LongReach CCTV IP PoE Extender Kit User Manual

Specifications

Environment

Devices

Transmission
Standard supported

PoE Power
Connectors

LED Indicators
Maximum Distance

RJ45 Pin Configuration

Reverse Polarity
Sensitive. Use EIA/TIA
568A or 586B straight­through wiring.

Cable

PoE Power Supply
(500113)

Power Consumption
Temperature

Enclosure
Accessories
Dimensions
Weight
Compliance
Warranty
Order Information

PoE CCTV IP
PoE CCTV IP cameras with a 10/100Mb/s Ethernet port, using up to

15.4 Watts.
Transparent to the user
Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX
IEEE 802.3af compatible PoE
Class 3
One (1) BNC 75 Ohms.
One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair.
Power, IP Traffic, 100MBps
RG59/RG6: Up to 980 ft (300m) @ 100Mbps
UTP Cat 5e/6: Up to 330 ft (100 m)

Note: When installed in an electrically noisy environment, an STP cable
must be used. Also, cross-connection reduces the effective distance
depending on the grade of twisted cable used.

RJ45 Link

Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)

UTP/STP: One (1) Cat 5e/6 or better twisted pair cables required
RG59/RG6: 75 Ohms (avoid CCS cable)
Optional PoE Power Supply (110-240V/48VDC/.625A, 2.1mm plug)
with inter-changeable blades (sold separately). Required at the Camera

Side Device when coax cable quality or length results in insufficient
power reaching the camera. Required at the Network Side Device
when used with non-PoE LAN switch.

Network Side: 1.82 Watt Camera Side: 1.73 Watt
Operating: 0° to 40°C Storage: -20° to 85°C
Humidity: Up to 95% non-condensing
Metal
Wall-mount brackets included

4.37” x 2.95” x 0.99” (110 x 75 x 25 mm)

1.5 lb (0.68 kg)
Regulatory: FCC, CE, RoHS Flammability: 94V0
2 years
500112 LongReach CCTV IP PoE Extender Kit
500113 Power Supply for 500112 (48VDC)

LongReach CCTV IP PoE Extender Kit

500112

Quick Installation Guide

Overview

The LongReach CCTV IP PoE Extender Kit (500112) allows one IP camera (15.4
Watts) to be connected up to 980 ft (300 m) via a single 75-ohm coax cable in a point­to-point configuration. The maximum distance depends on the grade and quality of
coaxial cable. An optional PoE 48VDC Power Supply (500113) is available if required.

Applications

CCTV IP surveillance

Installation

1. Identify the connectors on the Extenders as indicated on the product labels.

2. Attach the surface-mount brackets if required as shown below.

8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5

Tel: [phone] Fax: [phone]

Toll Free (North America): [phone]

E-mail: [e-mail] URL: www.muxlab.com

© MuxLab Inc. 94-000749-A SE-000749-A

3. Verify that the distance between the CCTV IP PoE extenders is within MuxLab
specifications (see Specifications table).

4. To install the Network Side Device:

3a. Connect the extender to the PoE Ethernet Switch with a UTP Cable.

Note: If the Ethernet Switch is not PoE; you will need to connect a PoE Power
Supply (500113) to the Network Side Device.

3b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX

LINK connector on the Extender.

5. To install the Camera Side Device:

4a. Connect the extender to the camera with a Cat5e/6 cable.

Note: If the quality or length of the coaxial cable reduces the power to a level that
is insuffiicent to power the camera, you will need to connect a PoE Power Supply
(500113) to the Camera Side device.

4b. Connect one (1) length of RG59 or RG6 coaxial cable to the COAX

LINK connector on the Extender.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions
in respect to the installation of the CCTV IP PoE Coax Extender Kit:

Network Side

Symptom

No Image OFF OFF OFF OFF No power • Check if the Ethernet

No Image ON OFF OFF OFF Coaxial Cable • Check the coaxial

No Image ON OFF OFF OFF Distance • Check the coaxial

No Image ON OFF ON OFF UTP Cable • Check the UTP Cable

No Image ON ON ON ON No Traffic • Check network

Choppy Image ON BLINK ON BLINK Distance • Check cable length

LEDs

Power IP Traffic Power IP Traffic

If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or ([phone] (International).

Camera Side

LEDs

Probable Cause

Possible

Solutions

switch is PoE.

• Check the power
connection.

cables.

cables length and
quality.

pin out.

configuration.

• Check the coaxial
cable quality.

6. Power on the equipment and verify the image quality. The following is a diagram
of a typical configuration.

© MuxLab Inc. 2013