Muxlab HDMI Passive Extender Kit User Manual
E-mail:
videoease@muxlab.com
URL:
www.muxlab.com
Specifications
Environment
Devices
Transmission
Bandwidth
Signals
Connectors
Maximum Distance
RJ45 Pin Configuration
Reverse Polarity Sensitive
Use EIA/TIA 568 A or B
straight-through wiring.
Cable
Temperature
Enclosure
Dimensions
Weight
Compliance
Warranty
Order Information
HDMI 1.4
DVD, plasma, projectors, monitors, TV, PC, laptops, servers
supporting HDMI.
Transparent to the user
225 MHz
HDMI 1.4 protocol
HDMI receptacle.
Two (2) RJ45S for Cat 5e unshielded or shielded twisted pair.
480i/p: Cat5e: 150 ft (45 m) Cat6: 200 ft (60 m)
720p, 1080i: Cat5e: 150 ft (45 m)
1080p:
STP is recommended where EMI/RFI may be an issue. Usage of
patch panels is not recommended. When connected to Deep
Color equipment, the 500402 removes the Deep Color content to
support greater cable length than would normally be achieved.
RJ45 A (Video)
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
RJ45 B (DDC)
Pin 1 (R) Pin 2 (T)
Pin 3 (R) Pin 6 (T)
Pin 4 (R) Pin 5 (T)
Pin 7 (R) Pin 8 (T)
Two (2) Cat5e/6 or better solid core twisted pair cables required
Operating: 0° to 55°C Storage: -20° to 85°C
Humidity: up to 95% non-condensing
Metal enclosure, PVC sleeve
10.6” x 1.9” x 0.8” (27.0 cm x 4.8 cm x 2.0 cm)
10.8 oz. (307 g)
Regulatory: FCC, CE, RoHS
Flammability: 94V1
2 years
500402 HDMI Passive Extender Kit
Cat5e: 100 ft (30 m) Cat6: 150 ft (45 m)
Cat6: 200 ft (60 m)
HDMI Passive Extender Kit (500402)
Quick Installation Guide
Overview
The HDMI Passive Extender Kit (500402) allows HDMI equipment to be
connected up to 150 ft (45m) @ 1080i via two (2) Cat5e unshielded twisted pair
cables in a point-to-point configuration. The product also works with 1080p up to
150 ft (45m) via Cat6 cable. The kit comes with one (1) Transmitter and one (1)
Receiver. Applications include; commercial and residential AV systems, classroom
projector systems, digital signage, boardroom systems, collaborative PC systems,
medical information systems.
Pre-Installation Check
Identify the connectors on the Source Side and Display Side as indicated on the
product.
© MuxLab Inc. 2011 94-000714-A SE-000714-A
8495 Dalton Road, Mount Royal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
Installation
Troubleshooting
Verify that the distance between the HDMI Transmitter and Receiver are within
MuxLab specifications (see Specifications table).
In order to install the HDMI Passive Extender Kit, please follow the steps below:
1. Connect two (2) lengths of Cat5e (or higher) grade UTP cables to the A and B
connectors on Transmitter (identified as HDMI Passive Extender Source
Side).
2. Connect the two (2) Cat5e (or higher) grade UTP cables to the A and B
connectors of the Receiver (identified as HDMI Passive Extender Display
Side).
Note: Verify that the cables are connected straight-through (i.e. A to A,
B to B) and not inverted.
3. Connect the Transmitter directly to the HDMI video source.
4. Connect the Receiver directly to the HDMI display equipment.
5. Power on the HDMI equipment and verify the image quality.
6. The following diagram shows the final configuration.
The following tables describe some of the symptoms, probable causes and possible solutions
in respect to the installation of the HDMI Passive Extender Kit. If you still cannot diagnose
the problem, please call MuxLab Customer Technical Support at 877-689-5228 (toll-free in
North America) or (+1) 514-905-0588 (International).
Picture/
Sound
No Image Wiring Check continuity
No Image Synchronization Power off the source and the
Flickering
Image
Choppy
Sound
Noise in
image
Green or
pink hue
Image
Flicker when
powering up
equipment
nearby
Probable Cause Possible Solution
Check correct wiring
Verify that A and B Cat5e
cables are not inverted.
display. Power on the
devices.
Synchronization Check cable length
Synchronization Check cable length
Weak signal Check cable length
Cable Check cables and replace.
Interference Use STP cables.
© MuxLab Inc. 2011
Loading...