Muxlab CCTV IP Extender Kit User Manual

@

m

Specifications

Environment

Devices

Standard supported

Maximum distance vs.
speed between unit

(higher speed on camera
side)

Cable between unit
Cable for Ethernet port

(Not included)

Indicators

(on both unit)

Ethernet Connectors

(on both unit)

Pin Configuration to
connect the two unit

(polarity insensitive)

Power Supply

(Included)

Power Consumption
Temperature

Enclosure
Dimensions
Weight
Compliance
Warranty
Ordering Information

CCTV IP
CCTV IP cameras, NVR, IP encoder, network switch and any device

with a 10/100Mb/s Ethernet port, supporting IP.
Ethernet side:
IEEE 802.3 10BaseT,
IEEE 802.3U 100Base-TX,
IP ver 4 and 6.
Line side: VDSL-DMT:
ITU-T G993.1 VDSL, ITU-T G997.1,
G.993.2 VDSL2 (profile not selectable).
Asymmetric speed, using twisted pair* and coax*:
1000ft (330m): 44/31Mbps, 44/31Mbps
2000ft (660m): 34/21 Mbps, 44/28 Mbps
3000ft(1000m): 28/10 Mbps, 39/26 Mbps
4000ft(1350m): 22/5.3 Mbps, 39/21 Mbps
5000ft(1600m): 17/1.2 Mbps, 31/14 Mbps
* The actual data rate will vary on the quality of the copper wire and
environment factors.
Coax 75 ohm/RG59 or twisted-pair telephone wire AWG24 or better.
Two CAT 5/5e/6 UTP cables are required (straight or crossover), up to
330ft(100m).
Power on.
Link/nego between the two unit working.
Ethernet: 10/100 Mb indicator.
Ethernet: Activity.
One isolated BNC 75 ohm female to connect remote unit.
One isolated RJ45 to connect remote unit.
One or two RJ45S with LED’s for Ethernet with auto reversal.
One power connector, 2mm.
Using RJ45 plug: Pin 4 & Pin 5 (1 pair required only, blue and
white/blue)
Using RJ11/RJ12 plug: Pin 3 & Pin 4 (1 pair required only, blue and
white/blue)
Using BNC: 75 ohms coax cable: Center & Shield (shield is isolated
from chassis)
Two 100-240V/5VDC 1.2A power supplies with interchangeable
blades for NA, Europe and UK.

3.25 Watts each unit
Operating: 0° to 60°C Storage: -55° to 85°C
Humidity: Up to 95% non-condensing
Plastic

4.50” x 3.00” x 1.25” (11.4 x 7.6 x 3.2 cm)
Approx. 1 lb. (0.5 kg)
Regulatory: FCC, CE, RoHS Flammability: 94V0
2 years
500110 CCTV IP Extender Kit.

CCTV-IP Extender Kit

500110

Quick Installation Guide

Overview

The CCTV-IP Extender Kit (500110) allows IP camera equipment (or any other IP
equipment) to be connected up to 1 mile (1600 m) using one coax cable with BNC or
one Cat 5/5e/6 unshielded twisted pair cable in a point-to-point configuration. The
maximum distance is dependent on speed required, type and length of cable. The kit
comes with one transmitter (camera side), one receiver (network side) and two identical
wall-mount power supplies. The camera side can accept one or two IP-cameras without
an additional Ethernet switch/router.

Applications

Applications include Surveillance IP-camera, digital signage and information systems.

8495 Dalton Rd, Montreal, Quebec, Canada. H4T 1V5

Tel: [phone] Fax: [phone]

Toll Free (North America): [phone]

E-mail: videoease

muxlab.com URL: www.muxlab.co

© MuxLab Inc. 94-000692-A

Installation

1. Identify the network side unit and the camera side unit as indicated on the product
labels. Note that if both unit are swapped they will still work but at reduced speed. The
camera side unit must therefore be placed always on the highest throughput side.

Troubleshooting

The following table describes some of the symptoms, probable causes and possible solutions
with the installation of the Extender Kit:

LEDS Condition

detected

PWR OFF: No

power.

Possible cause Action

No AC power or
defective power supply.

Try swapping the two power
supplies.

2. On the Ethernet side, the distance between product and network/camera is the usual

330ft (100m). The cable may be straight or crossed and must be connected into one of
the shielded RJ45 connectors (the ones with LEDs).

3. To connect both units together, use one of the three options:

3a. A single twisted pair (AWG #24) using a RJ11 plug, only the center pair are

needed. Connect it into the plastic RJ45 connector “RJ45 Link”.

3b. A single Cat 5/6 cable with a RJ45 plug, only the center pair are needed. Connect

it into the plastic RJ45 connector “RJ45 Link”.

3c. A 75 ohm coax cable with BNC. Connect it to “BNC Link”.

4. Connect a 5 VDC power supply to each unit, and then plug the power supply into

an AC power outlet. If power is present, the green Power LED should be on. If the
cable is correctly connected the Link LED should be on.

5. Connect the CCTV and network equipment to the CCTV IP extender and power on

all equipment. Verify that the activity LED is blinking while images are being
transmitted. The following is a typical application.

LINK OFF: No

functional link
between the 2
units.

FLASHING:
Processing.

ON: Normal.

10/100 OFF: 10Mb/s

ON: 100Mb/s

OTHER:
Speed much
slower than
expected.

Activity OFF: No data

transfer on
Ethernet side.

FLASHING:
Normal

Remote unit off or
defective.

Twisted pair cable not
connected to the right
pin.

Cable too long.

Equipment not
supporting 100 Mb/s or
not set to 100Mb/s.

Transmitter connected
to network instead of
camera.

Camera or network not
functioning. Defective
or disconnected
Ethernet cable.

Turn on remote unit. If defective
unit return both unit to factory.

Make sure both center pin are
used.

Length must be 5280ft (1600m) or
less.

If Link LED flashing does not stop
after 10 seconds, check cable.

To get the maximum throughput
the camera must be able to send at
100Mb/s.

Swap the Tx with the Rx. (The
throughput is not the same for both
units.)

Verify the camera and network
without the Extender kit, i.e.
connect the camera directly to the
network. Speed must be 10Mb/s or
100Mb/s only.

© MuxLab Inc. 2011

If you still can not diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or ([phone] (International).