MuxLab 500451-WP-RX Installation Guide
Specifications
Environment
HDMI 1.4a (3D)
Devices
DVD, plasma , pro je cto rs , mo nito rs , TV , PC , la ptops, servers supporting
HDMI.
Transmission
Transpar e nt to the use r
Bandwidth
340MHz
Signals
HDMI 1.4a protocol
Connectors
HDMI receptacle.
HDMI cables not included.
Max. Distance*
per end
Cat 5e/6: 200 ft (60 m) up to 1080P Deep Color
the grade of twisted cable used.
RJ45 Pin C o n figu r at i on
RJ45
Cable
One (1) Category 5e or better twisted pair cables required.
Power Supply
One (1) 110-240V/5VDC power supply with interchangeable blades
Power Consumption
6W
Temperature
Operating: 0º to 40º C. Storage:-20º to 85º C. Humidity: up to 95% noncondensing.
Enclosure
Metal Wall-Plate one gang
Dimensions
4.5” x 2.80” x 1.50” (115 x 71 x 38 mm). Choose 1.97” (50 mm) deep back
box to allow for Cat 5E/6 wiring connection.
Weight
1.6 LB (0.7 Kg)
Mounting
Scews included
Compliance
Regulatory: FCC, CE, RoHS
Warranty
2 years
Order Information
500451-WP-KIT HDMI Wall-Plate Extender Kit, HDBT Lite, UHD-4K
500451-WP-TX HDMI Wall-Plate Transmitter, HDBT Lite, UHD-4K
8495 Dalto n Road, Mount Royal, Quebec, Canada. H4T 1V5
E-mail: videoease@muxlab.com URL: www.muxlab.com
One (1) RJ45S for Cat5e/6 unshielded or shie l ded twisted pa ir .
*Based on a maximum length
of 6.6 ft (2m) of HDMI cable
Reverse Polarity Sensitive
Use EIA/TIA 568 A or B,
straight-through wi r ing.
131 ft (40 m) for 4K; 3840 x 2160/24, 25 &30 Hz.
When installed in an ele ctrically noisy environment, STP cable must be
used. Also, cr os s -connection reduces the effective dista nc e depending on
Pin 1 (R)
Pin 2 (T)
Pin 3 (R)
Pin 6 (T)
Pin 4 (R)
Pin 5 (T)
Pin 7 (R)
Pin 8 (T)
500451-WP-RX HDMI Wall-Plate Receiver, HDBT Lite, UHD-4K
Tel: (514) 90 5-0588 Fax: (514) 905-0589
© MuxLab Inc. 2014 94-000774-A / SE-000774-A © MuxLab Inc. 2014 1
Toll Free (North America): (877) 689-5228
HDMI Wall-Plate Extender Kit
(500451-WP-KIT)
Quick Installation Guide
Overview
The HDMI Wall-Plate Extender Kit (500451-WP-KIT) allows HDMI equipment to
be connected up to 200 ft (60m) @ 1080P via one (1) Cat5e/6 unshielded twisted
pair cables in a point-to-point configuration. The kit comes with one (1) Transmitter
and one (1) Receiver.
Applications incl ude; commercial and resid ential AV systems, classro om projector
systems, digital signage, boardroom systems, collaborative PC systems, medical
information systems.
Pre-Installatio n Check
Identify the connectors on the Transmitter (Source side) and Receiver (Display
side). The Source side has an HDMI In connector. The Display side has an HDMI
Out connector. Both products have two LED indicators for Power and RJ45 Sync,
IR Sensor and Emitter and a Power Supply connector.
Installation
or more or a mud ring. Connect the RJ45 plug
In order to install the Transmitter, please follow the steps below:
the Transmitter to the HDMI video source with an HDMI compliant
Connect the Receiver to the HDMI display equipment with an HDMI compliant
Connect the Cat5e (or higher) grade UTP cables to the RJ45 Link connectors of
to the Transmitter first and then plug the power supply into an AC power outlet.
Note: Power the HDMI Wall-Plate Extender Balun only after all
connections are made.
Contacts) and the IR Emitter a mono plug (2 Contacts).
Picture/
Sound
Power
LED
Sync
LED
Probable Cause
Possible Solution
No Im age
OFF
OFF
No power
Check pow er co nnections
No Im age
ON
OFF
Wiring
Check continuity
Check corr ect wiring
No Im age
ON
ON
Synchronization
Power off the source and the
on the devices.
Flickering Image
ON
ON
Synchronization
Check cab l e length
Choppy Sound
ON
ON
Synchronization
Check cab l e length
Noise in image
ON
ON
Weak signal
Check cab l e length
are certified HDMI 1.3a
Image Flicker when
equipment ne a r by
ON
ON
Interference
Use STP cables .
IR not functioning
ON
ON
Remote control not
source.
Make sure the IR Sensor is
IR not functioning
ON
ON
Interference from
lights
Place the IR eq uipment away
IR not functioning
ON
ON
Interference from RF
radiation from the TV
Place the IR eq uipment away
for the RF radiation
Verify that the distance between the HDMI Transmitter and Receiver are within MuxLab
specifications (see Specifications table).
1. Identify the pin configuration of the baluns. The pin configuration follows the
EIA/TIA 568A/B standard. The HDMI Wall-Plate Extender Kit is reverse
polarity sensitive. Please ensure that wiring is straight through (Ring to Ring,
Tip to Tip).
2. To install the HDMI Transmitter or Receiver in a single back box, choose a back
box with a depth of 1.97” (50 mm)
into the rear of the extender. Secure the extender with the 2 front screws.
12. The following diagram shows the final configuration.
3. Connect
cable.
4. Connect the Cat5e (or higher) grade UTP cables to the RJ45 Link connectors on
Transmitter.
5.
cable.
6.
the Receiver.
7. Connect the 5 VDC power supply first to the Receiver first and then plug the
power supply into an AC power outlet. Connect the 5 VDC power supply first
If power is present, then the green power LED of the Transmitter an d Receiver
will be ON.
8. Power on the HDMI equipment and verify the image quality
9. This product support bidirectional IR Control.
Note: You can diffe rentiate the IR Sensor and the IR Emitter by look ing
at the 3.5 mm plug. The IR Sensor is using a Stereo Plug (3
10. Position the IR Sensor so that it is directed to the hand-held remote control. For
a clear IR signal recept ion, aim the hand-held remote control to the top of the IR
Sensor enclosure.
11. Position the IR Emitter as close as possib le to th e source’s IR Senso r (i.e. DVD
player). For a clear IR signal reception, the IR Emitter can be glued on the
source’s IR Sensor. The IR Emitter’s signal is transmitted from the side of the
enclosure.
Troubleshooting
The following tables describe some of the symptoms, probable causes and possible solutions
in respect to the installation of the HDMI Wall-Plate Extender Kit.
display. Cycle power of the
HDMI Extender and power
Verify that the HDMI cables
powering up
directed to the IR
Sensor or IR Emitter
not directed to the
sunlight, Fluorescent,
Neon or Halogen
If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
directed towards the remote
and the IR Emitter to the
equipment
for the interfering light
© MuxLab Inc. 2014 2 © MuxLab Inc. 2014 3
Loading...