MuxLab 500028,500028-F Users Guide [ok]

Specifications
Environment Devices
3dB Bandwidth Maximum Input Insertion Loss per balun pair Common Mode Rejection
THD Audio Source Impedance Audio Receiver Impedance Max. Distance – Cat 5 UTP Pin Configuration (RJ45)
Cable – UTP
Cable - Coax Connectors
Temperature Enclosure Dimensions Weight Warranty Order Information
Line level unbalanced analogue audio DVD players, satellite receivers, MPEG players, laptops, hi-fidelity stereo audio amplifiers, audio switchers, AV monitors and other line level audio equipment. Transparent to the user. 20 Hz to 20 KHz over the distance range.
1.1Vp-p (unbalanced) Less than 2 dB over the frequency range.
Greater than 60 dB @ 1 KHz Greater than 40 dB over the frequency range. Less than 0.007% @ 1KHz 100 ohms maximum 10 k ohms minimum 3,250 ft (1 km) Audio 1 (White): pins 1[R] & 2 [T] Audio 2 (Red): pins 3 [R] & 6 [T] 24AWG or lower solid copper twisted pair wire Impedance: 100 ohms at 1 MHz; Maximum capacitance: 20 pf/foot. Attenuation: 6.6 dB/1000 ft at 1 MHz Shielded audio cable. 500028: Two (2) RCA-M 6” cable leads 500028-F: Two (2) RCA jacks One (1) RJ45 Operating: 0º to 55º C. Storage:-20º to 85º C. Humidity: up to 95% ABS. Fire retardant plastic
2.40” x 2.25” x 1.00” plus 6” audio lead
3.1 oz (89 gms) Lifetime 500028 Stereo Hi-Fi Balun, M 500028-2PK Stereo Hi-Fi Balun, M, 2-Pack 500028-F Stereo Hi-Fi Balun, F 500028-F-2PK Stereo Hi-Fi Balun, F, 2-Pack
Stereo Hi-Fi Balun (500028 & 500028-F)
Quick Installation Guide
Introduction
The Stereo Hi-Fi Balun (500028, 500028-F) allows unbalanced line level stereo audio to be transmitted up to 5,000 ft (1.5km) via unshielded copper twisted pair (UTP) in a point-to-point connection. Used in pairs, the product is designed for high fidelity applications where full audio bandwidth (20Hz to 20 KHz) is required. Used in pairs, the Stereo Hi-Fi Balun eliminates costly and bulky audio cable, allowing audio equipment to be connected or moved within a structured cabling environment. Applications include; audio distribution, high-fidelity sound systems, custom residential audio systems.
Installation
To install the Stereo Hi-Fi Baluns, perform the following steps:
1. One pair of Stereo Hi-Fi Baluns is required for each stereo channel.
2. Identify the pin configuration of the baluns. Two (2) twisted pairs are required as shown in the following diagram.
8495 Dalton Road, Mount Royal, Quebec, Canada, H4T 1V5
Tel.: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com URL: www.muxlab.com
94-000556-A SE-000589-B
© MuxLab Inc.
Note: The Stereo Hi-Fi Balun is phase polarity sensitive. Therefore, in order to achieve full stereo audio quality, please ensure that the wiring is straight-through and according to EIA568 (A or B) standard.
3. Verify the colors of the RCA plugs and connect one (1) Stereo Hi-Fi Balun to the left-audio and right-audio RCA connectors of the audio source.
4. Verify the colors of the RCA plugs and connect a second Stereo Hi-Fi Balun to the left-audio and right-audio RCA connectors of the audio receiver at the remote end.
5. Complete the connection between the two (2) baluns, using standard UTP cable, connector blocks and appropriate modular RJ45 outlets.
6. Power-on the audio equipment and check the audio quality. The audio should be clear within the maximum specified distances. The following diagram shows a typical configuration.
7. The female version requires respective RCA type audio cables (not included)
Troubleshooting
The following table describes some of the symptoms, probable causes and possible solutions in respect to the installation of the Stereo Hi-Fi Balun. If you still cannot diagnose the problem, please call MuxLab Customer Technical Support at 877-689-5228 (toll-free in North America) or 514-905-0588 (International).
Symptom Probable Causes Possible Solutions
Poor audio quality
No audio No power Check your audio system for power.
Audio phase cancellation Audio weak Distance specifications
EMI interference. Check that wiring is not too close to
transformers and ballasts.
Split pair Ensure that the UTP pairs are not
split and that each pair of wires is twisted.
Open circuit Check wiring to ensure continuity Defective balun Change Stereo Hi-Fi Baluns for
another pair.
Reversed wires Check for straight-through wiring.
Check DC loop resistance and verify
exceeded
if distance spec is exceeded. Reduce cable length or eliminate high-loss components.
© MuxLab Inc.
Loading...