Mutec MC-1.1, MC-1 Operating Manual

Page 1
ALL SOFTWARE AND HARDWARE PRODUCT NAMES ARE REGISTERED TRADEMARKS OF THEIR RESPECTIVE OWNERS. WE RESERVE THE RIGHT TO CHANGE TECHNICAL DETAILS WITHOUT PRIOR NOTICE.©MUTEC GmbH 2002•7045-014
WWW.i˙CLOCK-NET.DE
FAX 0049-(0)30-7468 80-99
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
REDUNDANT MULTIPLE CLOCK SYNTHESIZER AND VIDEO REFERENCE GENERATOR
REDUNDANT MULTIPLE CLOCK SYNTHESIZER AND VIDEO REFERENCE GENERATOR
\
B E D I E N U N G S A N L E I T U N G
B E D I E N U N G S A N L E I T U N G
B E D I E N U N G S A N L E I T U N G
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
VERSION 1.0
VERSION 1.00
O P E R AT I N G M A N U A L
O P E R AT I N G M A N U A L
O P E R AT I N G M A N U A L
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
PRELIMINARY
UNI-DIRECTIONAL DIGITAL AUDIO FORMAT CONVERTER
BI-DIRECTIONAL DIGITAL AUDIO FORMAT CONVERTER
Page 2
Page 3
SAFETY INSTRUCTIONS
General inst ructions
To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture, direct
sunlight or excessive heat from sources such as radiators or spotlights. No user serviceable parts are in-
side. Repair and maintenance must be carried out by qualified personnel authorized by MUTEC GmbH!
The unit has been designed for operation in a standard domestic environment. Do NOT expose the unit
and its accessories to rain, moisture, direct sunlight or excessive heat produced by such heat sources as
radiators or spotlights! The free flow of air inside and around the unit must always be ensured.
Initi al operati on
Prior to t he initial op eration of th e unit, the appliance, i ts access ories and p ackaging mu st be
inspe cted for a ny signs of phy sical dama ge that may have o ccurred du ring transi t. If the uni t has
been da maged mec hanically o r if liquids ha ve been spilled inside t he enclosure, the appli ance may
not be co nnected t o the mains or mu st be disco nnecte d from the main s immediat ely! If the un it is
damag ed, please do NOT return i t to MUTEC Gmb H, but noti fy your deal er and the shi pping com-
pany immediately, o therwise claims for d amage or rep lacement m ay not be grant ed.
If the device is left in a low-temperature environment for a long time and then is moved to a room-
temperature environment, condensation may occur on the inside and the exterior. To avoid short-
circuits and flashovers, be sure to wait one or two hours before putting the device into operation.
Power su pply
The device contains a self-adapting wide-range power supply supporting the majority of global stan-
dard line voltages within a range of 90…250 V, with no need for making adjustments. Make sure that
your line-voltage source provides a supply voltage within the specified range. In addition, make sure
that the device is properly grounded via the local electric installation.
Pleas e use the encl osed powe r cord (see p ackaging) to connect t he unit to the ma ins. Switc h the
unit of f before you a ttempt to connect it t o the mains. C onnect th e power cord to t he unit, the n
to a standard 3-pin mains outl et. To draw the po wer cord, ne ver pull on the c able but on th e mains
plug!
The uni t must be grou nded durin g operation!
For information on the power-inlet wiring, refer to the »Wirin g of connec tors« section in the
appendix. Disconnect the device from the mains when not using it for an extended period!
This symbol, an exclamation mark inside a triangle,
alerts you to important operating or safety instructions
in this manual.
This symbol, a flash of lightning inside a triangle, alerts
you to the presence of uninsulated dangerous voltage
inside the enclosure - voltage that may be sufficient to
constitute a risk of shock.
Decla ration of Conformity
We herewith confirm that the product complies with the European
Commission’s standards on electromagnetic compatibility.
Interference emission: EN 50081-1, 1992
Resistance to interference: EN 50082-1, 1992
Presupposed as operation condition is that all clock outputs are con-
nected with high-quality and good shielded BNC 75 ohms cable.
!
R I S K O F
ELECTRICAL SHOCK!
C A U T I O N
!
WARRANTY REGULATIONS
§1 Warranty
MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs within
the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge within 90
days. The purchaser is not entitled to claim an inspection of the device free of charge during the warranty period. If the warranty claim proves to be justified, the product
will be returned freight prepaid by MUTEC GmbH within Germany. Outside Germany, the product will be returned with the additional international freight charges payable
by the customer. Warranty claims other than those indicated above are expressly excluded.
§2 Warranty tra nsferability
This warranty is extended exclusively to the original buyer who bought the product from a MUTEC GmbH specialized dealer or distributor, and is not transferable to anyone
who may subsequently purchase this product. No other person (retail dealer, distributor, etc.) shall be entitled to give any warranty promise on behalf of MUTEC GmbH.
§3 Waranty reg ulations
The return of the completed registration card, or online registration on one of the websites specified below, is a condition of warranty. Failing to register the device before
returning it for repair will void the extended warranty.
The serial number on the returned device must match the one stated on the registration card or entered during online registration. Otherwise, the device will be
returned to the sender at the sender’s expense.
Any returned device must be accompanied by a detailed error description and a copy of the original sales receipt issued by a MUTEC dealer or distributor.
The device must be returned free of shipping expenses and in the original package, if possible; otherwise, the sender has to provide comparably protective packaging.
The sender is fully responsible for any damage or loss of the product when shipping it to MUTEC GmbH.
§4 Limitation of warranty
Damage s caused by the following conditio ns are not cove red by this war ranty:
Damage s caused by every kind o f normal wear a nd tear (e.g. d isplays , LEDs, potentiomet ers, faders, swi tches, bu ttons, co nnectin g element s, printed labels, co ver
glass es, cover p rints, an d similar par ts).
Funct ional failur e of the produ ct cause d by imprope r install ation (please obser ve CMOS compon ents handl ing instru ctions !), negle ct or misus e of
the pro duct, e.g . failure to op erate the uni t in complian ce with the in structions given in t he user or se rvice man uals.
Damage c aused by an y form of ext ernal mecha nical impa ct or modif ication.
Damage c aused by th e user’s fai lure to conne ct and oper ate the unit in c ompliance w ith local s afety reg ulations .
Damage c aused by fo rce majeure ( fire, expl osion, flo od, lightn ing, war, vanda lism, etc .).
Conse quential damages or de fects in p roduct s from other m anufactu rers as well a s any costs resulting fr om a loss of pr oductio n.
Repair s carried o ut by perso nnel which i s not authori zed from MUT EC GmbH will void the warrant y. Adaptations and modifications to the device made with regard to
national, technical, or safety regulations in a country or of the customer do not constitute a warranty claim and should be set with MUTEC GmbH in advance.
§5 Repairs
To obtain warranty service, the buyer must call or write to MUTEC GmbH before returning the unit. All inquiries must be accompanied by a description of the problem and
the original buyer’s invoice. Devices shipped to MUTEC GmbH for repair without prior notice will be returned to the sender at the sender’s expense. In case of a functional
failure please contact:
MUTEC G esellsc haft fuer Sy stement wicklung und Komponent envertri eb mbH
Siekewe g 6/8 • 1230 9 Berlin • Germany • Fon 03 0-74688 0-0 • Fax 030-746880-9 9 • tecsupp ort@iCLOCK-net.de
all software/hardware product names are registered trademarks of their respective owners. No part of
this manual may be reproduced, copied or converted to a machine-readable form or electronical media
without a written permission of MUTEC GmbH. We reserve the right to change or improve our products
without notice. © MUT EC GmbH 2002 -2005
Page 4
Page 5
About this Manual
Additional Features for MC-1.1
. . . . . . . . . . . . . . . .
8
Applications
. . . . . . . . . . . . . . . . . . . . . . . . . . .
8
. . . . . . . . . . . . . . . . . . . . . . .
Wiring the AES/EBU and S/PDIF Interfaces
. . . . . . . . . .
electing Function Areas and
s
etting Functions
S/PDIF
, S/PDIF
, AES/EBU
S/PDIF
, S/PDIF
, AES/EBU
AES/EBU
S/PDIF
, S/PDIF
, AES/EBU
. . . . . . . . . . .
SYMMETRICAL
. . . . . . . . . . . . . . . . . . .
AES/EBU (only MC-1.1)
. . . . . . . . . . . . . .
AES/EBU (only MC-1.1)
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
APPENDIX
Technical Data
Page 6
Page 7
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
\
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
Thank you very much for purchasing
About this Manual
The whole manual is related to both versions in general
,
and MC-1.1
The individual differences are mentioned in the according sections and
chapters.
The structure of this manual refers to the normal process of installing
in a standard audio studio environment. Thus the chapters are
to get to know the general functionality of
and MC-1.1
and to reach
The chapter OPERATION describes individual functions which enable the
and MC-1.1
to every studio environment. The chapters
APPLICATION EXAMPLE and APPENDIX include descriptions of favorable
studio set-ups as well as all technical information.
cleared up by the content of this manual, please feel free to contact your
WARRANTY REGULATIONS located at the beginning of the manual.
and
are multifunctional, high-performance digital audio for-
verters help to interconnect digital audio devices which are using different
transmission formats and are equipped with incompatible interfaces. The
format conversion process does not only the necessary electrical conversion
the specifications which are standardized by the Audio Engineering Society
Various additional operation modes
like ADAT line extension through
AES/EBU lines, SCMS processing or signal status detection
-1
and
specially
for bi-directional connections
which
s
to run two signal paths individually. In addition, this unit con-
s
TM
signal splitter and
AES/EB
between
the original signal to pass through.
ADAT
TM
transfer through AES/EBU lines.
with
an exclamation mark should
These include
additional information which are of major
the text column.
!
The grey boxes contain supplementary
the text column beside the box.
Page 8
\\\\\\\\\\\\
I N T R O D U C T I O N
I N T R O D U C T I O N
I N T R O D U C T I O N
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
Additional Features for MC-1.1
from 32 kHz to 192 kHz
ADAT
TM
signal splitting
line exten
sion.
optical/coaxial
AES/EBU signal splitt
TM
signal distribution.
Applications
send/returns of digital mixing consoles and effect processors.
with professional digital audio equipment.
TM
and S/PDIF optical signals through
symmetrical AES/EBU lines for e.g. theater or broadcast installations.
copying.
8
88
88
Page 9
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
\
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
This red LED lights up when the unit is switched on with the rear panel
The toggle switch selects one of the two functional areas available.
MODE
This function area includes all digital audio format conversion modes avail-
SCMS
This function area offers four different ways to encode the outgoing
6
STATUS
This area
coaxial digial audio signals by means of status LEDs.
OP
Thses outputs transmit digital S/PDIF audio signals (optical) in accordance
with the specifications of the standard IEC 60958 or ADAT
TM
signals (Toshiba
Toslink
TM
connector, EIAJ standard).
for signal splitting and distribution
9
MC-1 Rear Panel
MC-1.1 Rear Panel
MC-1.1 Front Panel
MC-1 Front Panel
432
3
6
6
Page 10
\\\\\\\\\\\\\
C O N T R O L E L E M E N T S
C O N T R O L E L E M E N T S
C O N T R O L E L E M E N T S
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
S/PDIF
CO
These outputs transmit unbalanced digital S/PDIF audio signals (coaxial)
Ω.
AES/EBU OUT
These outputs transmit a balanced digital AES/EBU audio or blank frame
signal compliant with AES 3 – 1992 (R1997) and AES 11 – 1997/2003. The
(XLR connectors, male).
for signal splitting and distribution
AES/EBU IN
This input receives a balanced digital AES/EBU audio or blank frame signal
compliant with AES 3 – 1992 (R1997) and AES 11 – 1997/2003. The input
(XLR connector, female).
S/PDIF
CO
This input receives unbalanced digital S/PDIF audio signals (coaxial) based
Ω.
OP
This input receives digital S/PDIF audio signals (optical) in accordance with
the specifications of the standard IEC 60958 or ADAT
TM
signals (Toshiba
Toslink
TM
connector, EIAJ standard).
MAINS IN, Power Switch + Power Inlet
This is the main switch for switching the device on and off. Be sure to
turning on the switch. Heed the SAFETY INSTRUCTIONS at the beginning of
this manual.
and
TECHNICAL DATA
sections
Page 11
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
\
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
ontent of the Box
The unit was packed carefully. Nevertheless we recommend to check the
content directly after opening the package:
4 x Rubber feet
The unit should be set up as closely as possible to the devices to which it
will be connected, so as to avoid excessive cable lengths. Use the 4 rubber
feets enclosed with the appliance and stick them symmetrically on the
from being damaged.
The device can be mounted into a standard 19“ rack and will require 1 unit.
for sufficient ventilation! The mounting depth including the terminals is
Additional slide-in rails on the rack inside are recommended for safe instal-
Wiring the AES/EBU and S/PDIF interfaces
cables equipped with XLR connectors on both ends. The specifications
stipulate a specific cable resistance of 110
(ask your retailer for a confir-
cal cables equipped with cinch connectors on both ends. The specifications
stipulate a specific cable resistance of 75
tion of this value when purchasing the cables).
accessories to rain, moisture,
direct sunlight, or excessive heat
environment of the device must be ensured!
!
The condition of the packaging
and WARRANTY REGULATIONS.
!
at the beginning of this manual
should be read carefully.
!
cables for the transmission of digital S/PDIF
AES/EBU clock rates well shielded
clock lines are imperative to avoid
!
Page 12
\\\\\\\\\\\\
I N S TA L LAT I O N
I N S TA L LAT I O N
I N S TA L LAT I O N
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
Page 13
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
\
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
The device is fully operated using the two toggle switches at the front
Switching the SELECT switch selects between different basic
function areas.
Switching the DATA switch selects between the individual
functions within one function area.
the
AFETY INSTRUCTIONS and
We also recommend reading the CONTROLS
AND TERMINALS chapter for information on
!
First press on SELECT or DATA switch enables the last selected function
within the last selected function area. The corresponding LED is
beginning to flash.
Every press on DATA switch will select a new function. The LED of every
selected function will flash accordingly and the corresponding function is
available at once.
When the needed function is selected, do not press the switches again!
After a period of approx. 4 seconds the LED in front of the selected
function will stop flashing.
The STATUS area is not accessible by using the SELECT and DATA switches,
All user-specific function settings
are available furthermore when
!
selects individual
functio
SELECT + DATA operation
Function Areas + Functions
Page 14
\\\\\\\\\\\\
O P E R AT I O N
O P E R AT I O N
O P E R AT I O N
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
The function area MODE at MC-1 includes four, and at MC-1.1 seven
the SCMS data included in incoming S/PDIF streams will be analyzed and
front panel labeled as »NON-PCM« and »DTS-CD« will light accordingly.
This functionality applies not to incoming AES/EBU digital audio signals
which are not defined in AES 3 and AES 11.
The MODE factory default is basically S/PDIF
OP
, the SCMS factory default is
OP
S/PDIF
OP
, S/PDIF
CO
, AES/EBU
CO
S/PDIF
OP
, S/PDIF
CO
, AES/EBU
This functions convert an incoming S/PDIF optical (index »
OP
CO
this process a »real« format and electrical conversion of the S/PDIF data
stream will be done to the AES/EBU output aligned to AES 3 or AES 11,
while an electrical conversion will be carried out to the S/PDIF optical and
coaxial outputs. The original input signal will be transfered
the format-same output.
The SCMS data-bits of the S/PDIF optical and coaxial outputs can be set as
AES/EBU
S/PDIF
OP
, S/PDIF
CO
, AES/EBU
This function converts an incoming AES/EBU reference signal to all three
conversion of the AES/EBU data stream will be done to the S/PDIF optical
IEC 60958
, while the original AES/EBU signal
will be refreshed and jitter-cleaned transfered to the AES/EBU output.
The SCMS data-bits of the S/PDIF optical and coaxial outputs can be set
SYMMETRICAL
This function offers an electrical conversion between the AES/EBU and
signal reference. Here the AES/EBU input and the S/PDIF output just like the
capable to transfer digital data simultaneously in both directions.
Thus, MC-1 and MC-1.1 can be used to transfer e.g. ADAT
TM
-based signals
via symmetrical AES/EBU lines. Since the data transmission with optical
cables is limited to 10 meters, as mentioned above, the
SYM-
gives you the benefit of being able to transmit signals
without any loss over considerably greater distances of up to 100 m, e.g.
SYMMETRICAL, it is not possible to set SCMS functions
OP
AES/EBU (only MC-1.1)
This function converts an incoming S/PDIF optical (index »
OP
signal to the AES/EBU output and an incoming AES/EBU reference signal
to the S/PDIF optical output simultaneously. During this processes »real«
format and electrical conversions of the S/PDIF and AES/EBU data streams
will be done based on the double conversion circuitries of MC-1.1. Both
signal paths can be used with different clock rates
simultaneously.
The SCMS data-bits of the S/PDIF optical output can be set as described in
the »SCMS Function Area« section. The factory default is PASS.
This function requires a second
transmission chain, in order to
convert the symmetrical signal back to the
optical signal.
!
Page 15
\\\\\\\\\\\\
O P E R AT I O N
O P E R AT I O N
O P E R AT I O N
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
CO
AES/EBU (only MC-1.1)
This function converts an incoming S/PDIF coaxial (index »
CO
signal to the AES/EBU output and an incoming AES/EBU reference signal
to the S/PDIF coaxial output simultaneously. During this processes »real«
format and electrical conversions of the S/PDIF and AES/EBU data streams
will be done based on the double conversion circuitries of MC-1.1. Both
signal paths can be used with different clock rates
simultaneously.
The SCMS data-bits of the S/PDIF coaxial output can be set as described in
the »SCMS Function Area« section. The factory default is PASS.
This function connects all inputs directly to the outputs of their same for-
will be refreshed and jitter-cleaned before being transfered to their corre-
sponding outputs. All three signal paths can be used with different clock
f
the S/PDIF optical in
ADAT
TM
signal. Thus, MC-1.1 can be used as an
ADAT
TM
signal splitter, while
the other interfaces
the incoming data streams with help of the STATUS area.
the AES 3 and AES 11 specifications do not define any SCMS capability. Due
to this, the AES/EBU output signal is free of SCMS information.
coaxial)!
This function called »Original« sets the outgoing SCMS data-bits to indicate
that the signal source is the original master and not a copy. Therefore
SYMMETRICAL
signal source.
This function called »1st Generation« sets the outgoing SCMS data-bits
to indicate that the signal source is a copy. Therefore devices which are
capable of evaluating SCMS data-bits will not accept those digital audio
signals at their S/PDIF inputs for recording. Due to this, valuable recordings,
sounds or commercial material will be protected against illegal copying. 1st
SYMMETRICAL
signal source.
sponsibility for criminal use of the
sively to protect the musical productions
of the original MC-1 and MC-1.1 owner
against illegal copying by third parties
and to help the owner to use his digital
audio data more easily within his own
studio environment .
With release of the German copyright pro-
tection law at August, 8
th
2003, the use of
equipment which is capable of eliminating
copy protections is not allowed!
!
Page 16
\\\\\\\\\\\\\\\\\\
A N H A N G
A N H A N G
A N H A N G
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
This function transmits all SCMS information received at one of the
AES/EBU is the signal source
SYMMETRICAL is activated
OP
AES/EBU (only MC-1.1) is activated
CO
AES/EBU (only MC-1.1) is activated
signal source.
This function sets the outgoing SCMS data-bits to indicate that there is
signals at their inputs for recording. NONE is not available when one of the
following functions is used:
SYMMETRICAL
signal source.
The STATUS area provides information on various signal statuses of incom-
status bits in the AES/EBU data stream.
This status LED indicates when the incoming digital audio signal of the
This status LED indicates when the incoming digital audio signal of the
This status LED indicates when the incoming digital audio signal of the active
This status LED indicates when the incoming digital audio signal of the
Page 17
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
\
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
B E D I E N E L E M E N T E
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
APPENDIX
2
AES/EBU XLR Output
AES/EBU XLR Input
Page 18
\\\\\\\\\\\\
A P P E N D I X
A P P E N D I X
A P P E N D I X
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
88
Technical Data
S/PDIF OPTICAL INPUT
Interfaces
1 x Toshiba ToslinkTM, EIAJ RC-5720
Format IEC 60958
Resolution 16 – 24 bits
Lock range Every digital audio clock rate from 32.0 kHz to 192.0 kHz
S/PDIF COAXIAL INPUT
Interface 1 x Coaxial (Cinch/RCA female), unbalanced, input impedance 75 Ω, 200 mV –7 V
Format IEC 60958
Resolution 16 – 24 bits
Lock range Every digital audio clock rate from 32.0 kHz to 192.0 kHz
AES/EBU INPUT
Interface 1 x XLR female, transformer balanced, input impedance 110 Ω, 200 mV – 7.0 V
Format AES/EBU 3 – 1992/2003 + AES/EBU 11 – 1997/2003
Resolution 16 – 24 bits
Lock range Every digital audio clock rate from 32.0 kHz to 192.0 kHz
S/PDIF OPTICAL OUTPUT
Interface 1 x Toshiba ToslinkTM, EIAJ RC-5720
Format IEC 60958
Resolution 16 – 24 bits
Transmitted audio clock rates Every digital audio clock rate from 32.0 kHz to 192.0 kHz
S/PDIF COAXIAL OUTPUT
Interface
1 x Coaxial (Cinch/RCA female), unbalanced, 0.5 Vpp @ 75
, output impedance 75 Ω,
buffered
Format IEC 60958
Resolution 16 – 24 bits
Transmitted audio clock rates Every digital audio clock rate from 32.0 kHz to 192.0 kHz
AES/EBU OUTPUT
Interface 1 x XLR male, transformer balanced, 3.5 Vpp @ 110 Ω, output impedance 110 Ω, buffered
Format AES/EBU 3 – 1992/2003 + AES/EBU 11 – 1997/2003
Resolution 16 – 24 bits
Transmitted audio clock rates Every digital audio clock rate from 32.0 kHz to 192.0 kHz
SIGNAL PROCESSING
Signal conversion
S/PDIF (optical) ↔ S/PDIF (coaxial) digital audio electrical conversion S/PDIF (optical + coaxial) ↔ AES/EBU digital audio electrical + format conversion
SCMS copy bit
Generation of original, 1st generation, no copy protection status SCMS pass-thru functionality
S/PDIF signal analyzing Automatic detection of SCMS original + 1st generation status; none-PCM and DTS detection
POWER SUPPLY
Type
Internal, switching power supply
Input voltage 90 V – 260 V (automatic adjustment), 47 Hz – 440 Hz
Power consumption max. 10 W
SYSTEM UNIT COVER
Cover size / material / color 196 x 42 x 156mm without connectors (W x H x D), aluminium sheet 1mm, black
Front panel size / material 198 x 44 x 2mm (W x H x D), aluminium Weight: MC-1 ~ 612g Weight: MC-1.1 ~ 631g
Page 19
Page 20
ALL SOFTWARE AND HARDWARE PRODUCT NAMES ARE REGISTERED TRADEMARKS OF THEIR RESPECTIVE OWNERS. WE RESERVE THE RIGHT TO CHANGE TECHNICAL DETAILS WITHOUT PRIOR NOTICE.©MUTEC GmbH 2002•7045-014
WWW.MUTEC-NET.DE
FON 0049-(0)30-746880-0
FAX 0049-(0)30-74 6880-99
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
Loading...