Mutable Instruments Peaks User Manual
LFO: Low frequency oscillator
go back to the 4 standard functions.
5 waveforms are provided, each of them continously
variable:
• Sine with wavefolding
• Triangle with controllable ascending/descending ratio
• Square with duty cycle control
• Stepped triangle with variable number of steps
• Clocked noise with interpolation control
DRUM: Analog modeling drums
Channel 1 is a modeled analog bass drum, and channel
2 a modeled snare drum.
Knob TWIN & EXPERT mode SPLIT mode
1 Frequency BD attack
2 Frequency modulation/
tone
3 Attack/noisiness SD tone
4 Decay SD noisiness
Note: With extreme noisiness and tone settings, the
snare drum turns into a hi-hat.
BD decay
Knob TWIN & EXPERT mode SPLIT mode
1 Frequency Ch. 1 Frequency
2 Waveform Ch. 1 Waveform
3 Waveshape variation Ch. 2 Frequency
4 Initial phase Ch. 2 Waveform
The trigger resets the LFO to the phase set by the
“initial phase” control.
TAP: Tempo synchronized LFO
This function is similar to the LFO except that the frequency is synchronized to the rate of the input trigger
signals, or to the “taps” on the buttons (G) and (H).
Knob TWIN & EXPERT mode SPLIT mode
1 Amplitude Ch. 1 Waveform
2 Waveform Ch. 1 Shape
3 Waveshape variation Ch. 2 Waveform
4 Initial phase Ch. 2 Shape
Tips
Hold the function selection switch (F) for 1 second to
unlock 4 new secret functions. Repeat this operation to
go back to the 4 standard functions.
Peaks
Dual trigger converter
About Peaks
Front panel
ENV: Envelope generator
Peaks is a 2-channel multi-function signal generator:
envelopes, synchronized low-frequency oscillations, or
drum signals can be generated in response to triggers.
Installation
Peaks requires a -12V / +12V power supply (2x5 pins
connector). The red stripe of the ribbon cable (-12V side)
must be oriented on the same side as the “Red stripe”
marking on the board.
The power consumption is as follows:
-12V: 2mA ; +12V: 60mA.
Online manual and help
The manual can be found online at
mutable-instruments.net/modules/peaks/manual
For help and discussions, head to
mutable-instruments.net/forum
A. B. C. D. Parameters. Refer to the tables in the next
sections.
E
A
F
B
E. Control mode selection switch and LED.
F. Function selection switch and LEDs.
G. H. Manual trigger buttons for channels 1 & 2.
1. 2. Channel 1 & 2 trigger inputs.
3. 4. Channel 1 & 2 signal outputs.
Control modes
G
C
1
D
H
2
3 4
Peaks can operate in 3 different modes:
TWIN: Both channels share the same parameters but
can be triggered independently. The 4 knobs control the
4 parameters. Perfect for duophony!
SPLIT: Knobs 1&2 control two main parameters of channel 1; and knobs 3&4 two main parameters of channel 2.
Press the button (E) to switch back and forth between
TWIN and SPLIT mode. The LED is lit in SPLIT mode.
EXPERT: Channel 1 and 2 are completely independent.
Hold the button (E) for 1 second to enter the EXPERT
mode. Press (E) to change the channel. The LED blinks
once when channel 1 is active, twice when channel 2 is
active. Hold (E) for 1 second to leave the EXPERT mode.
Attack time Decay time
Release time
Sustain
level
Knob TWIN & EXPERT mode SPLIT mode
1 Attack Ch. 1 Attack
2 Decay Ch. 1 Decay
3 Sustain Ch. 2 Attack
4 Release Ch. 2 Decay
In Twin & Expert modes, the envelope is an ADSR and
requires a Gate signal.
In Split mode, the envelope is a simpler AD, and only
requires a Trigger signal.
Loading...