Muskoka Chair CEDAR Assembly Instructions Manual
Muskoka Chair
Assembly Instructions
For: Thickness Arm & Rail Width
¾” 5½”
¾” 8”
1” 7½”
1032 Henshaw Lake Road, Box 494, Port Carling, ON P0B 1J0
705-765-3836
www.muskokachair.com
Muskoka Chair Assembly Instructions
Tools Needed: Cordless Drill
#2 Robertson Bit
9/16” Socket or Adjustable Wrench
Tips:
Separate all parts in kit box into five sections (as marked)
Section A Rail Assembly 15 parts ¾” x 8” & 1” x 7½” ............................... Pages 1 - 5
14 parts ¾” x 5½”
Section B Back Support Assembly, 5 parts ................................................. Pages 6 - 7
Section C Chair Back Assembly, 10parts................................................... Pages 8 - 13
Section D Arm and Front Leg Assembly, 8 parts ..................................... Pages 14 - 23
Section E Front Plate “Install” Only, 1 part .......................................................Page 24
Total = 39 Parts for ¾”x 8” & 1” x 7½”
38 Parts for ¾” x 5½”
66 (approx) - 1½” Screws
2 - 2” Carraige Bolts
¾” x 5½” & ¾”x 8”
2 - 2½” Carraige Bolts
1” x 7½”
11 - 1½” Round Head Screws - USE ONLY for base strap (7) and rail assembly (4)
12 - 1¼” Screws USE ONLY for bottom back piece (4)
and for each arm assembly (4)
Section D
4 - 1½” hex head bolts
¾” x 5½” & ¾”x 8”
6 nuts, 6 washers
If all parts and hardware are accounted for, lets begin.
If not call 1-705-765-3836 for assistance.
4 - 2” hex head bolts
1” x 7½”
Part A - Rail Assembly, 16 Parts Page 1
¾” x 5½” Muskoka Chair
Seat Base
2F
2E
2D
2C
2B
Left
Side
Rail
Under Chair Dowel
Right
Side
Rail
¾” x 8” & 1” x 7½” Muskoka Chair
2A
1A
1B
1C
Seat Base
2F
2E
2D
2C
2B
Left
Side
Rail
Under Chair Dowel
2A
Right
Side
Rail
1A
1B
1C
1D
Part A - Rail Assembly, continued
1½” round head screw
Page 2
Screw - 4 (1½” round head screw)
Screw - 3
(1½” round head screw)
Under Chair Dowel -1
Screw - 2 (1½” round head screw)
From outside
left and right rail
screw into under
chair dowel.
(Pre-drilled 1” holes to set
dowels into)
Right Rail
Under Chair Dowel - 2
Screw - 1 (1½” round head screw)
Left Rail
Part A - Rail Assembly, continued
¾” x 5½”
Page 3
Seat Slat 2B
1½” round head screws
Placement of second slat
(¾” x 5½” only) use sticks after
second slat is installed
Pewter Slat - 5½” only
Placement of rst seat slat
Use spacer sticks from
¾” x 8” Chair
1” x 7½” Chair
(Seat Slat 2B)
here forward
Part A - Rail Assembly, continued
Reminder: Sticks only for 8” and 7½” chair
Placement of 2nd Seat Slat 2A
Page 4
Spacer Sticks
¾” x 5½” Muskoka Chair ¾” x 8” & 1” x 7½” Muskoka Chair
2C
2A
1A
1B
1C
1D
2D
2E
2F
Seat Base
2B
2A
2C
2B
1A
1B
1C
2D
2E
2F
Seat Base
Part A - Rail Assembly, continued Page 5
¾” x 5½” Muskoka Chair
¾” x 8” & 1” x 7½” Muskoka Chair
Part A - Rail Assembly, continued
Picture of Finished Rail Section
Page 5a
Part B - Back Support Assembly, 5 parts
Back Support Dowel (shorter of the 3 dowels supplied)
Left or Right
Arm Support
Page 6
Back Support Right Side
Back Support Left Side
Same
Screw
Screw
Back Support Dowel
Part B - Back Support Assembly, 5 parts
NOT HERE
Page 7
Screw
Screw
Screw
Screw
Pre-Drilled
Holes To Accept Screws
Loading...