Muskoka Electric Fireplace MM258E, Simcoe MM258E, Simcoe MM258W, Simcoe MM258OK Assembly Instructions Manual
ELECTRIC FIREPLACE
111
YEAR
ANN E
A!O
I
N
H
O
M
E
W
A
R
R
A
N
T
Y
G
A
R
A
N
T
I
E
"
L
A
M
A
I
S
O
N
G
A
R
A
N
T
#
A
E
N
S
U
P
R
O
P
I
A
C
A
S
A
MANTELS
MANTEAUX DE CHEMINÉES
ÉLECTRIQUES
REPISAS PARA
CHIMENEAS ELÉCTRICAS
Assembly Instructions
Instructions d'assemblage
Instrucciones de montaje
MM258E
MM258W
MM258OK
REV00
TIPS FOR THE ASSEMBLY OF
YOUR NEW MANTEL
• Before you begin assembly, locate the instructions and hardware. Take out all the parts and
compare them to the diagrams below. Be sure you have all the parts and can identify them.
• A helping hand is always good. Assemble your mantel with an adult assistant if possible. Some
pieces are heavy and will need to be held by a helper. Assembly time will take approximately
30-60 minutes.
TOP 1PC
ESPRESSO: ZZ.258E.01
WHITE: ZZ.258W.01
OAK: ZZ.258OK.01
BASE 1PC
ESPRESSO: ZZ.258E.02
WHITE: ZZ.258W.02
OAK: ZZ.258OK.02
UPPER FACING PANEL 1PC
ESPRESSO: ZZ.258E.07
WHITE: ZZ.258W.07
OAK: ZZ.258OK.07
LOWER FACING PANEL 1PC
ESPRESSO: ZZ.258E.08
WHITE: ZZ.258W.08
OAK: ZZ.258OK.088
INSIDE
LEFT FRONT
PANEL 1PC
ESPRESSO:
ZZ.258E.03
WHITE:
ZZ.258W.03
OAK:
ZZ.258OK.03
VIEW
LEFT SIDE
PANEL 1PC
ESPRESSO:
ZZ.258E.04
WHITE:
ZZ.258W.04
OAK:
ZZ.258OK.04
OUTSIDE
VIEW
RIGHT FRONT
PANEL 1PC
ESPRESSO:
ZZ.258E.05
WHITE:
ZZ.258W.05
OAK:
ZZ.258OK.05
FIREBOX SHELF 1PC
ESPRESSO: ZZ.258E.09
WHITE: ZZ.258W.09
OAK: ZZ.258OK.09
RIGHT SIDE
PANEL 1PC
ESPRESSO:
ZZ.258E.06
WHITE:
ZZ.258W.06
OAK:
ZZ.258OK.06
17PCS 17PCS
2PCS 2PCS 4PCS 4PCS
ANTI-TIP DEVICE 2 SETSWINGNUT AND LOCK WASHER
4PCS
1
GET READY TO START
Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or
exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the
hardware bag which is
DO NOT discard any pieces.
Step 1
Locate the base and place it on the floor. DO NOT put it up against
the wall at this point in the assembly, as you need to get in behind
the mantel to insert several wingnuts, lock washers and firebox screws.
Step 2
Locate the left side panel and the left front panel. Facing the
front of the base, take the left side panel, positioning it so the
holes in the blocks on the bottom line up with the holes on the
base. Position the left front panel next to the left side panel, lining
up the holes in the blocks with the holes on the base. Attach the
left front and side panel to the base by inserting and tightening
1 wingnut and 1 lock washer to each piece. Attach the left side
and front panels together by inserting and tightening 2 wingnuts
and 2 lock washers.
RED and located inside the packaging, taped to the top box. Be sure you
Step 3
Repeat Step 2, but with the right side panel and the right
front panel.
2
Loading...