MUSIC Tribe PH ULM200M01 User Manual

ULM200USB/ULM202USB Controls
Model: ULM200M
(1)
Model: ULM200D
(5)(4)
(2) (3)
Type of product: Wireless Microphone
ULM200USB/ULM202USB Controls
1. POWER/STATUS LED
2. W VOLUME Button (Mute/volume down)
3. V VOLUME Button (Power on/unmute/volume up)
4. USB connector
ULM200USB/ULM202USB Getting Started
1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connec tor on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible produc ts, or to a USB port on a computer.
V
2. Press and hold the microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will  ash slowly during the connec ting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the the volume
4. A long press of the microphone into mute. The mute condition is indicated by rapid  ashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the batter y is low by regular brief  ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will  ash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down af ter 10 seconds.
button on the ULM200M wireless
V
and W buttons to adjust
W
button will put the ULM200M
V
button will unmute the ULM200M
V
and W buttons and moving the microphone
Speci cation
RF output <100 mW / +20 dBm
Operating range 120 m (Line of Sight)*
Dynamic range 92 dB, A-weighted**
Equivalent input noise -112 dBu
Frequency Response 20 Hz - 20 kHz, ±1 dB (Wireless Link)
Sampling rate 48 kHz
Resolution 24-bit
Encoding 232 kbps SLAC (Slightly
Lossy Audio Codec)
Latency 14.5 ms
RF frequency 2.4 GHz ISM band
(2406 MHz - 2474 MHz), 18 channels
Power Supply current 70 mA @ +5 VDC
Battery type 2 x AA (LR6)
Alkaline cells
Battery life >30 hours
Dimensions (W x D x H) 45.7 x 45.7 x 243.8 mm
(1.8 x 1.8 x 9.6")
Weight 0.4 kg (0.9 lbs)
*Achieva ble range wi ll be depend ent on nearby s ources of RF in terfere nce and/ or line of s ight obst acles.
**Mea sured fro m analog inpu t to analog out put, unit y gain oper ation with out wireless compression.
ULM200USB/ULM202USB Controles
Model: ULM200M
(1)
Model: ULM200D
(5)(4)
(2) (3)
Tipo de producto: Micrófono inalámbrico
ULM200USB/ULM202USB Controles
1. Piloto de encendido/estado POWER/STATUS
2. Botón W VOLUME (anulación/reducción de volumen)
3. Botón V VOLUME (Encendido/aumento de volumen)
4. Conector USB
5. Piloto de estado de enlace inalámbrico
ULM200USB/ULM202USB Puesta en marcha
1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connec tor on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible produc ts, or to a USB port on a computer.
V
2. Press and hold the microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will  ash slowly during the connec ting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the the volume
4. A long press of the microphone into mute. The mute condition is indicated by rapid  ashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the batter y is low by regular brief  ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will  ash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down af ter 10 seconds.
button on the ULM200M wireless
V
and W buttons to adjust
W
button will put the ULM200M
V
button will unmute the ULM200M
V
and W buttons and moving the microphone
ULM200USB/ULM202USB Réglages
Model: ULM200M
(1)
Model: ULM200D
(5)(4)
(2) (3)
Type de produit : micro sans l
ULM200USB/ULM202USB Réglages
1. Témoin Led d’É TAT/ALIME NTATION
2. Bouton W VOLUME (couper/diminuer le volume)
3. Bouton V VOLUME (mise sous tension/augmenter
levolume)
4. Connecteur USB
5. Témoin Led d’état de la liaison sans  l
ULM200USB/ULM202USB Mise en œuvre
1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connec tor on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible produc ts, or to a USB port on a computer.
V
2. Press and hold the microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will  ash slowly during the connec ting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the the volume
4. A long press of the microphone into mute. The mute condition is indicated by rapid  ashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the batter y is low by regular brief  ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will  ash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down af ter 10 seconds.
button on the ULM200M wireless
V
and W buttons to adjust
W
button will put the ULM200M
V
button will unmute the ULM200M
V
and W buttons and moving the microphone
ULM200USB/ULM202USB Regler
Model: ULM200M
(1)
Model: ULM200D
(5)(4)
(2) (3)
Produkttyp: Drahtlosmikrofon
ULM200USB/ULM202USB Regler
1. BETRIEB/STATUS-LED
2. W VOLUME-Taste (stummschalten /leiser)
3. V VOLUME-Taste (einschalten/lauter)
4. USB-Anschluss
5. Wireless Link Status-LED
ULM200USB/ULM202USB Erste Schritte
1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connec tor on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible produc ts, or to a USB port on a computer.
V
2. Press and hold the microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will  ash slowly during the connec ting sequence and will light solid once connected. If the ULM200M wireless microphone cannot connect to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the the volume
4. A long press of the microphone into mute. The mute condition is indicated by rapid  ashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the batter y is low by regular brief  ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will  ash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down af ter 10 seconds.
button on the ULM200M wireless
V
and W buttons to adjust
W
button will put the ULM200M
V
button will unmute the ULM200M
V
and W buttons and moving the microphone
ULM200USB/ULM202USB Controles
Model: ULM200M
(1)
Model: ULM200D
(5)(4)
(2) (3)
Tipo do produto: Microfone sem o
ULM200USB/ULM202USB Controles
1. LED POWER/STATUS
2. Botão de W VOLUME (Mute/abaixa o volume)
3. Botão de V VOLUME (Power on/aumenta o volume)
4. Conector USB
5. LED Status de Link Wireless (sem  o)
Primeiros Passos ULM200USB/ULM202USB
1. Connect the ULM200D wireless receiver to the “WIRELESS ONLY!” USB connec tor on wireless-enabled BEHRIINGER mixers, powered speakers or other compatible products, or to a USB port on a computer.
V
2. Press and hold the microphone to connect wirelessly to the ULM200D receiver. The LED on the microphone will  ash slowly during the connecting sequence and will light solid once connec ted. If the ULM200M wireless microphone cannot connec t to a receiver, the microphone will automatically power down after 10 seconds.
3. Once connected, the ULM200M microphone will be set at a medium volume. Use the the volume
4. A long press of the microphone into mute. The mute condition is indicated by rapid  ashing of the LED. If the user does not unmute within 60 seconds, the ULM200M microphone will power down to save batter y life.
5. A short press of the microphone. If the ULM200M microphone is unmuted more than 10 seconds after muting, it will return to the previous volume level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the batter y is low by regular brief  ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless receiver, the microphone can be re-paired from the powered down state by simultaneously pressing the buttons and moving the microphone to within 10 cm (4 inches) of the ULM200D wireless receiver. The LED on the microphone will  ash slowly during the pairing sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair to the receiver it will automatically power down af ter 10 seconds.
button on the ULM200M wireless
V
and W buttons to adjust
W
button will put the ULM200M
V
button will unmute the ULM200M
V
and W
LEGAL DISCLAIMER
MUSIC Group accepts no liabilit y for any loss which may be su ered by any person who relies either wholly or in par t upon any description, photograph, or statement contained herein. Technical speci cations, appearances and ot her information are subje ct to change without notice. All trademarks are the proper ty of their respective owners. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER , BUGERA and DDA are trademarks or registered trademark s of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding MUSIC Group’s Limited Warranty, please see complete details online at music-group.com/warranty.
NEGACIÓN LEGAL
MUSIC Group no admite ningún tipo de responsabilidad por cualquier daño o pérdida que pudiera sufrir cualquier per sona por con ar total o parc ialmente en la descripciones, fotograf ías o a rmaciones contenidas en este doc umento. Las especi caciones técnic as, imágenes y otras informaciones contenidas en este documento están sujetas a modi c aciones sin previo aviso. Todas las marcas comerciales que aparecen aquí son propiedad de sus resp ectivos dueño s. MIDAS, KLARK TEKNIK , TURBOSOUND, BEHRINGER, BUGERA y DDA son marcas comerciales o marcas registradas de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Reservados todos los derechos.
GARANTÍA LIMITADA
Si quiere conocer los detalles y condiciones aplicables de la garantía así como información adicional sobre la Garantía limitada de MUSIC group, consulte online toda la información en la web music-group.com/warranty.
DÉNI LÉGAL
MUSIC Group ne peut être tenu pour responsable pour toute perte pouvant être subie par toute pers onne se  ant en partie ou en totalité à toute description, photographie ou a rmation contenue dans ce document. Le s caractéristiques, l’apparence et d’autre s informations peuvent f aire l’objet de modi c ations sans noti cation. Toutes les marques appartiennent à leurs propriétaires respectifs. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA et DDA sont des marques ou marques déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Tous droits réservés.
GARANTIE LIMITÉE
Pour connaître les termes et conditions de garantie applicables, ainsi que les informations supplémentaires et détaillées sur la Garantie Limitée de MUSIC Group, consultez le site Internet music-group.com/warranty.
HAFTUNGSAUSSCHLUSS
MUSIC Group üb ernimmt keine Haf tung für Verluste, die Personen entstanden sind, die sich ganz oder teilweise auf hier enthaltene Beschreibungen, Fotos oder Aussagen verlassen haben. Technische Daten, Erscheinungsbild und andere Informationen können ohne vorherige Ankündigung geändert werden. Alle Warenzeichen sind Eigentum der jeweiligen Inhaber. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA und DDA sind Warenzeichen oder eingetragene Warenzeichen der MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Alle Rechte vorbehalten.
BESCHRÄNKTE GARANTIE
Die geltenden Garantiebedingungen und zusätzliche Informationen bezüglich der von MUSIC Group gewähr ten beschränk ten Garantie  nden Sie online unter music-group.com/warranty.
LEGAL RENUNCIANTE
O MUSIC Group não se responsabiliza por perda alguma que possa ser sofrida por qualquer pessoa que dependa, seja de maneira complet a ou parcial, de qualquer descrição, fotogra a, ou declaração aqui contidas. Dado s técnicos, aparências e outras informações estão sujeitas a modi cações sem aviso prévio. Todas as marcas são propriedade de seus respec tivos donos. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA e DDA são marc as ou marcas regis tradas do MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 Todos direitos res ervados.
GARANTIA LIMITADA
Para obter os termos de garantia aplicáveis e condições e informações adicionais a respeito da garantia limitada do MUSIC group, favor veri car detalhes na íntegra através do website music-group.com/warranty.
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE INFORMATION
ULTRALINK ULM200USB/ULM202USB
Responsible Par ty Name: MUSIC Group Services
NV Inc.
Address: 5270 Procyon Street
Las Vegas, NV 89118 USA
Phone Number: +1 702 800 8290
ULTRALINK ULM200USB/ULM202USB
complies with the FCC rules as mentioned in the followingparagraph:
This equipment has been tested and found to comply with the limit s for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio f requency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a par ticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correc t the interference by one or more of the followingmeasures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment
and receiver
Connect the equipment into an outlet on a circuit di erent
from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician
forhelp
This device complies with Part 15 of the FCC rules. Operation is subjec t to the following t wo conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any inter ference received, including inter ference that may cause undesired operation.
Important information:
Changes or modi cations to the equipment not expressly approved by MUSIC Group can void the user’s authority to use the equipment.
Operation in the 2.4 GHz ISM (Industrial, Scienti c, Medical) frequency band may be subject to interference from other transmitting equipment operating in this band. In the event of such interference, please verify and reassign the transmitting channels of any potentially interfering transmitting equipment.
We Hear You
Loading...