![](/html/99/99fa/99fad5f2551ed6f20bae84999d15a2c24c7213a58500109c518b934f4e6538c0/bg1.png)
SPECIFICATIONS
Max output power 100mW into 40Ω
>100mW for loads >40Ω
THD <0.02% 20Hz-20kHz unweighted
<0.007% 20Hz-20kHz "A" weighted
S/N ratio >80dB unweighted
>86dB "A" weighted
Power requirement 12V AC 500mA (via mains
adaptor supplied)
Dimensions (mm) 110 x 110 x 220 (W x H x D)
width and height include feet
INSTRUCTIONS FOR USE
All measurements are made at 3.5mW into 40Ω
Musical Fidelity reserves the right to make improvements which may result in
specification or feature changes without notice.
![](/html/99/99fa/99fad5f2551ed6f20bae84999d15a2c24c7213a58500109c518b934f4e6538c0/bg2.png)
Introduction
Thank you for purchasing the X-CANS. We sincerely hope that
the X-CANS will bring you many years of outstanding headphone
listening pleasure.
Connections
All connections should be made before the mains adaptor is
plugged in.
Installation Precautions
Your new X-CANS is designed and built to provide trouble-free
performance, as with all electronic devices it is however necessary to
observe a few precautions. Please ensure that you have complied
with these before you connect the power to your X-CANS. Retain
this guide for future reference.
nn Do not use the X-CANS near water.
nn Keep the X-CANS away from heat sources such as
radiators.
nn Only use the mains adaptor provided. The use of
other adaptors could seriously damage your XCANS.
nn Place all connecting cables where they are not likely
to be walked on or trapped by items placed on them.
This Hi-Fi product has been tested to ensure that its operation
will not be adversely affected by normal background levels of R.F.I.
(Radio Frequency Interference). It is possible that if the unit is subjected to abnormally high levels of R.F.I. the unit may not perform as
expected. In the unlikely event of this happening please contact
Musical Fidelity's service department.
Do not remove any covers, the X-CANS will not be covered
under warranty if it has been tampered with. There are no adjustments within. Please refer all service work to an authorised Musical
Fidelity agent.
Caution!
The X-CANS can be easily connected either to an available line
level output or into the tape monitor loop of most amplifier systems.
If your system has an unused line level output (for instance an
unused tape record output) simply connect a set of RCA/phono leads
from this output to the Line In sockets on the X-CANS rear panel as
shown below.
If there is no spare set of outputs the X-CANS can be connected
between your amplifier and tape recorder (in the tape monitor loop)
in the following way.
Connect a set of RCA/phono leads from the amplifier Tape
Record ouputs (sometimes labelled Tape Out) to the X-CANS Line
In sockets on the rear panel. Then connect another set of RCA/phono
lead from the Line Out sockets on the X-CANS rear panel to the Line
In (or Tape Record) input of your tape recorder. See below.
With either type of connection whichever source is selected on
your amplifier, will automatically be sent to the X-CANS for
headphone listening.
For the best results we recommend that you use Musical Fidelity X-LINX "no-nonsense" interconnect cables for all connections.
The X-CANS is capable of producing high listening levels with
very low distortion into most headphones. Be aware that prolonged
high level listening can permanently damage your hearing.
The X-CANS has been designed so that it may be left on indefi-
nitely.