Musical Fidelity XCAN Mk2 Owners manual
INSTRUCTIONS FOR USE
SPECIFICATIONS
V2
Output power Typically 1W
Input Impedance 47KOhms
THD <0.015% 20Hz-20kHz unweighted
<0.005% 20Hz-20kHz "A" weighted
S/N ratio >96dB unweighted ref. full output
>108dB "A" weighted ref. full output
Frequency Response 30Hz to 75Khz <+/- 1.0dB
Power requirement 12V AC 500mA (via mains
adaptor supplied)
Dimensions (mm) 110 x 110 x 220 (W x H x D)
width and height include feet
Musical Fidelity reserves the right to make improvements which may result in
specification or feature changes without notice.
X-CANV2issue 1 January 2000
Introduction
All connections should be made before the mains adaptor is plugged in.
can be easily connected either to an available line level out
put or into the tape monitor loop of most amplifier systems.
If your system has an unused line level output (for instance an unused tape
record output) simply connect a set of RCA/phono leads from this output to
the Line In sockets on the X-CAN
If there is no spare set of outputs the X-CAN
your amplifier and tape recorder (in the tape monitor loop) in the following
Connect a set of RCA/phono leads from the amplifier Tape Record outputs
(sometimes labeled Tape Out) to the X-CAN
panel. Then connect another set of RCA/phono lead from the Line Out sock
rear panel to the Line In (or Tape Record) input of
your tape recorder. See below.
With either type of connection whichever source is selected on your ampli
fier, will automatically be sent to the X-CAN
For the best results we recommend that you use Musical Fidelity X-LINX
"no-nonsense" interconnect cables for all connections.
has been designed so that it may be left on indefinitely.
Thank you for purchasing the X-CANV2. We sincerely hope that it will bring you
many years of outstanding headphone listening pleasure.
Connections
Installation Precautions
Your new X-CANV2is designed and built to provide trouble-free performance, as
with all electronic devices it is however necessary to observe a few precautions.
Please ensure that you have complied with these before you connect the power to
your X-CANV2. Retain this guide for future reference.
n Do not use the X-CANV2near water. The unit shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the unit.
n Keep the X-CANV2away from heat sources such as radiators. No naked
flame sources, such as lighted candles, should be placed on the
unit.
n Only use the mains adaptor provided. The use of other adaptors
could seriously damage your X-CANV2.
n Place all connecting cables where they are not likely to be
walked on or trapped by items placed on them.
n X-CANV2will operate in accordance with its specifications as long as
the environmental conditions are kept in the following ranges:-
Temperature 5 to 45 degrees Celsius
Humidity 10 to 90% non condensing
This Hi-Fi product has been tested to ensure that its operation will not be
adversely affected by normal background levels of R.F.I. (Radio Frequency
Interference). It is possible that if the unit is subjected to abnormally high
levels of R.F.I. the unit may not perform as expected. In the unlikely event
of this happening please contact Musical Fidelity's service department.
Do not remove any covers, the X-CANV2will not be covered under warranty if it
has been tampered with. There are no adjustments within. Please refer all service
work to an authorised Musical Fidelity agent.
The X-CAN
V2
AMPLIFIER
way.
ets on the X-CAN
Tape Out
AMPLIFIER
Line Out
V2
Caution!
The X-CANV2is capable of producing high listening levels with very low distortion into most headphones. Be aware that prolonged high level listening can permanently damage your hearing.
The X-CAN
V2
Loading...