Musical Fidelity X-10 Mk3, X-10-D Owners manual
SPECIFICATIONS
Input impedance 470KOhms
Output impedance <33 Ohms
THD <0.004% 10Hz to 20kHz
Frequency response 20Hz to 65kHz +0, -0.5dB
Crosstalk better than 80dB, 20Hz to 20kHz
S/N ratio >93dB unweighted ref. full output
>106dB "A" weighted ref. full output
Valve (tube) type 6112 (two)
Power requirement 12 - 0 - 12Volts AC 500mA
(via mains adaptor supplied)
Dimensions 180mm (7.1") wide
88.2mm (3.5") high including feet
218mm (8.6") deep including
RCA sockets
Weights Unit, net : 2.5kg(5lbs 8oz)
Adapter, net :0.45kg(1lb)
Total packed :3.1kg(6lbs 13oz)
TUBE OUTPUT BUFFER
Instructions for use
Musical Fidelity reserves the right to make improvements which
may result in specification or feature changes without notice.
X-10 V3Issue 2 May 2004
Introduction
sockets are simply duplicates of
-
’s
inlet socket, and plug the power supply itself into a convenient wall mains
ready for use. Allow a minute or so for the valves (tubes) to warm up, then
please note that the mains adapter may become warm to the touch - this is
Thank you for purchasing the X-10 V
hope that it will bring you many years of outstanding listening pleasure.
3
Tube Output Buffer. We sincerely
Connections
All connections should be made before the mains adaptor is plugged in.
Installation Precautions
Your new X-10 V
but as with all electronic devices, it is necessary to observe a few precautions :
n Do not use the X-10 V
to dripping or splashing and no objects filled with liquids, such as
vases, must be placed on the unit.
n Keep the X-10 V
sources, such as lighted candles, should be placed on the unit.
n Only use the mains adaptor provided. The use of other adaptors
could seriously damage your X-10 V
n Place all connecting cables where they are not likely to be walked on
or trapped by items placed on them.
n X-10 V
following environmental range :
This Hi-Fi product has been tested to ensure that its operation is not adversely affected by normal background levels of Radio Frequency Interference
(R.F.I.), and that it does not itself generate excessive amounts of interference.
However, if a problem persists, please contact your Musical Fidelity agent.
Never open the case of the X-10 V
antee. There are no user adjustments inside. Please refer all service work to
an authorised Musical Fidelity agent.
3
is designed and built to provide trouble-free performance,
3
near water. The unit must not be exposed
3
away from heat such as radiators. No naked flame
3
.
3
will operate in accordance with its specifications within the
Temperature5 to 45 degrees Celsius
Humidity 10 to 90% non condensing
3
yourself, as this will invalidate the guar-
Using good quality RCA leads (not supplied), connect the left and right
outputs from your CD player or other audio source to the X-10 V
3
LINE
INPUTsockets. The LOOP OUTPUT
the LINE INPUT, and are directly connected internally. This is to allow
further connection to other audio equipment if required.
Now connect your X-10 V
3
left and right OUTPUTSto the CD or auxil
iary inputs of your amplifier system.
Connect to amplifier
BUILT IN TAIWAN
Input from CD player
or other audio source
Plug the AC connector lead from the power supply unit into the X-10 V
Optional output to other
audio equipment
AC inlet from
mains adaptor
3
outlet. The blue LEDon the front panel will light to confirm the unit is
sit back and enjoy the music.
X-10 V3Issue 2 May 2004
This product has been designed so that it may be left on indefinitely, but
normal.
Loading...