Murray 425619x24B Operator Manual

Model
425619x24B
SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE.
PRODUCT INFORMATION
The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to make sure state laws and other laws are followed.
RECORD THE FOLLOWING INFORMATION ABOUT YOUR UNIT. THIS INFORMATION IS NECESSARY WHEN ORDERING PARTS OR IN CASE OF LOSS OR THEFT.
F–040739L
BUILT IN THE
TABLE OF CONTENTS
WARRANTY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESPONSIBILITY OF THE OWNER 3. . . . . . . . . . . . . . . . .
SAFETY RULES 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTERNATIONAL PICTORIALS 9. . . . . . . . . . . . . . . . . . . . .
ASSEMBLY 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS BAG – CONTENTS 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO INSTALL THE SEAT 11. . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO ASSEMBLE THE STEERING WHEEL 11. . . . . . . . . . . .
HOW TO ASSEMBLE THE GAUGE WHEELS 11. . . . . . . . . . . . .
MAINTENANCE FREE BATTERY 12. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO INSTALL THE BATTERY CABLES 12. . . . . . . . . . . . . .
IMPORTANT! BEFORE YOU START MOWING 13. . . . . . . . . . . .
HOW TO PREPARE THE ENGINE 13. . . . . . . . . . . . . . . . . . . . . . .
CHECK THE LEVEL OF THE MOWER HOUSING 13. . . . . . . . . .
CHECK THE TIRES 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATION 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOCATION OF CONTROLS 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATTACHMENTS 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO USE THE THROTTLE CONTROL 15. . . . . . . . . . . . . . . .
HOW TO USE THE BLADE ROTATION CONTROL 15. . . . . . . . .
HOW TO USE THE SPEED CONTROL PEDAL 16. . . . . . . . . . . .
HOW TO DISCONNECT THE TRANSMISSION 16. . . . . . . . . . . .
HOW TO SET THE PARKING BRAKE 17. . . . . . . . . . . . . . . . . . . .
HOW TO CHANGE THE CUTTING HEIGHT 17. . . . . . . . . . . . . . .
HOW TO STOP THE UNIT 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO TRANSPORT THE UNIT 17. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO OPERATE WITH THE MOWER HOUSING 18. . . . . . . .
HOW TO OPERATE THE UNIT ON HILLS 18. . . . . . . . . . . . . . . . .
BEFORE STARTING THE ENGINE 19. . . . . . . . . . . . . . . . . . . . . . .
HOW TO START THE ENGINE 19. . . . . . . . . . . . . . . . . . . . . . . . . .
OPERATING TIPS 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOWING AND BAGGING TIPS 20. . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE CHART 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO CHECK THE MUFFLER 21. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REMOVE AND INSTALL THE BLADE 22. . . . . . . . . . .
HOW TO SHARPEN THE BLADE 22. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO ADJUST THE BLADE ROTATION CONTROL 23. . . . .
HOW TO CHECK AND ADJUST THE MOTION DRIVE BELT 24
HOW TO CHECK AND ADJUST THE DRIVE BRAKE 25. . . . . . .
MAINTENANCE FREE BATTERY 25. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO CHARGE THE BATTERY 25. . . . . . . . . . . . . . . . . . . . . . .
WHERE TO LUBRICATE 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO CHECK THE FUEL FILTER 26. . . . . . . . . . . . . . . . . . . . .
CHECK THE TIRES 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REMOVE THE MOWER HOUSING 27. . . . . . . . . . . . . .
HOW TO INSTALL THE MOWER HOUSING 27. . . . . . . . . . . . . . .
HOW TO ADJUST THE GAUGE WHEELS 28. . . . . . . . . . . . . . . .
HOW TO LEVEL THE MOWER HOUSING 29. . . . . . . . . . . . . . . .
HOW TO REPLACE THE MOTION DRIVE BELT 30. . . . . . . . . . .
HOW TO REPLACE THE MOWER DRIVE BELT 31. . . . . . . . . . .
HOW TO INSTALL THE WHEELS 32. . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REPLACE THE FUSE 33. . . . . . . . . . . . . . . . . . . . . . . . . .
HOW TO REPLACE THE LIGHT BULB 33. . . . . . . . . . . . . . . . . . .
HOW TO CLEAN THE MOWER HOUSING 33. . . . . . . . . . . . . . . .
STORAGE (OVER 30 DAYS) 33. . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE SHOOTING CHART 34. . . . . . . . . . . . . . . . . . . . .
HOW TO ORDER REPAIR PARTS 35. . . . . . . . . . . . . . . . . . .
PARTS LIST 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLOPE GUIDE 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAWN TRACTOR ACCESSORIES 52. . . . . . . . . . . . . . . . . .
MURRAY, INC. Two Year Limited Warranty
Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of Two (2) Years from the date of purchase; however, this warranty does not cover engines, accessories (such as snow blowers, snow blades, grass baggers and plows), transmissions, batteries and Normal Wear Parts (except as noted below) or transaxles as the companies that manufacture these items furnish their own warranties and provide service through their authorized field service facilities. For additional information, see the warranties covering these particular parts. If you are uncertain whether your unit contains or is equipped with one or more of these parts, consult your dealer prior to purchase. Subject to the terms and conditions noted in this Limited Warranty, we shall, at our option, repair or replace at no cost to the original purchaser any part covered by this Limited Warranty during the applicable warranty period.
In the event the battery proves defective within ninety (90) days from the date of purchase, we will replace it without charge. If the battery proves defective after (90) days but within one hundred twenty (120) days from the date of purchase, we will replace it for a charge of one half (1/2) of the retail price of the battery in effect at the time of return.
Normal Wear Parts are defined as belts, blades, blade adapters, pneumatic tires, headlights and seat covers. These parts are warranted to be free from defects in material and workmanship as delivered with the product. Any claim for repair or replacement of Normal Wear Parts must be made within thirty (30) days of the date of purchase. No claims involving damage caused from material use, abuse or misuse will be honored.
This Murray, Inc. Two (2) Year Limited Warranty is your exclusive remedy; however, this warranty is void or does not apply to any unit that has been tampered with, altered, misused, abused or used for rental or other commercial and/or professional (non–homeowner) uses. Your warranty does not cover minor mechanical adjustments which are not due to any defect in material or workmanship. For assistance in making such adjustments, consult your Instruction Book.
To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, return the unit (or if authorized in advance, the defective part) along with your proof of purchase to an Authorized Service Center near you. To locate the nearest Authorized Service Center, call the Central Parts Distributor for your area shown in the list provided with your unit or check the Yellow Page listings in your local telephone directory. If you return the entire unit, we will repair the unit. If we authorize the return of the defective part only, we will either replace or repair the part. In the case of a defect in a transmission or differential (as distinguished from a transaxle), the entire transmission or differential must be returned since they do not include user serviceable parts.
This Murray, Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
implied warranty of merchantability and warranty of fitness for a particular purpose. If you need additional information on this written warranty or assistance in obtaining service, write or call: MURRAY, INC., Outdoor Power Equipment, Customer Service Department, P.O. Box 268, Brentwood, Tennessee 37027. (1–800–251–8007)
This Limited Warranty is given in lieu of all other expressed and implied warranties including the
F–040739L
2
OWNER’S INFORMATION
This instruction book is for several different models. The instructions are written for a person with some mechanical ability. Like most ser­vice books, not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can follow with some mechanical ability. Read and follow these instructions before you use the unit.
Know your product: If you understand the unit and how the unit oper­ates, you will get the best performance. As you read this manual, com­pare the illustrations to the unit. Learn the location and the function of the controls. To help prevent an accident, follow the operating instruc­tions and the safety rules. Keep this manual for future reference.
IMPORTANT: Many units are not assembled and are sold in car- tons. It is the responsibility of the owner to make sure the assembly instructions in this manual are exactly followed. Other units are pur­chased in an assembled condition. On assembled units, it is the re­sponsibility of the owner to make sure the unit is correctly assembled. The owner must carefully check the unit according to the instructions in this manual before it is first used.
RESPONSIBILITY OF THE OWNER
The responsibility of the owner is to follow the instructions below.
1. Carefully read and follow the rules for safe operation.
2. Follow all the assembly instructions.
3. Inspect the unit.
4. Make sure that the operator of the unit knows how to correctly use all standard and accessory equipment.
5. Operate the unit only with guards, shields, and other safety items in place and working correctly.
6. Correctly adjust the unit.
7. Service the unit only with authorized or approved replacement parts.
8. Complete all maintenance on the unit.
Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other repro­ductive harm.
Battery posts, terminals and related accesso­ries contain lead and lead compounds, chemi­cals known to the State of California to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
Environmental Awareness
D Do not fill the engine’s fuel tank completely full.
D Drain fuel for off–season storage.
D Use only unleaded gasoline.
D Service the air cleaner regularly.
D Change oil regularly. Use 10W–30 oil in summer.
D Tune–up the engine regularly.
D Keep equipment in efficient operating condition.
D Dispose of used engine oil properly.
SAFETY RULES
Safe Operation Practices for Ride–on Mowers
WARNING: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
I. General operation
1. Read, understand and follow all instructions in the Instruction Book, on the machine, the engine and with any attachments before starting.
2. Only allow responsible adults, who are familiar with the instructions, to operate the machine.
3. Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.
4. Be sure the area is clear of other people before mowing. Stop the machine if anyone enters the area.
5. Never carry passengers.
6. Turn off power to the blades or any attachments before backing up. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
7. Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either the entire grass bagger or the mower guard in place.
8. Slow down before turning.
9. Never leave a machine unattended with the engine running. Always turn off the blade(s), set the parking brake, stop the engine and remove the key before dismounting.
10. Turn off power to attachment(s) when transporting or not in use. Turn off the blade(s) when not mowing.
11. Stop the engine before removing the grass bagger or unclogging the chute.
12. Mow only in daylight or good artificial light.
13. Do not operate the machine while under the influence of alcohol or drugs or when very tired.
14. Watch for traffic when operating near or crossing roadways.
15. Use extra caution when loading or unloading the machine into a trailer or truck.
16. Turn off all attachment clutches before attempting to start the engine.
17. Always wear goggles, safety glasses, or an eye shield when you operate the unit to protect your eyes from foreign objects that can be thrown from the unit. Always wear eye protection when you make an adjustment or repair to the machine.
18. Use care when pulling loads or using heavy equipment. a. Use only approved drawbar hitch points.
F–040739L
3
OWNER’S INFORMATION
b. Limit loads to those you can safely control. c. Do not turn sharply. Use care when backing. d. Use counterweights or wheel weights when suggested in the Instruction Book.
19. Do not operate this machine if you are taking drugs or other medication which can cause drowsiness or affect your ability to operate this machine.
20. Do not use this machine if you are mentally or physically unable to operate this machine safely.
21. Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower related injuries. These opera­tors should evaluate their ability to operate a riding mower safely enough to protect themselves and others from serious injury.
II. Slope operation
Slopes and rough terrain are major factors related to loss–of–control and tip–over accidents, which can result in severe injury or death. ALL slopes require extra caution. If you cannot back up the slope or if you feel uneasy on the slope, do not mow it. See the “Slope Guide” in the back of this book to check for safe operation.
DO
1. Mow up and down slopes, not across.
2. Remove obstacles such as rocks, limbs, etc...
3. Watch for holes, ruts or bumps. Uneven terrain could overturn the machine. Tall grass can hide obstacles.
4. Use slow speed on slopes. Do not make sudden speed changes.
5. Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.
6. Use extra care with grass baggers or other attachments, they can change the stability of the machine.
7. Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.
8. Avoid starting or stopping on a slope. If tires lose traction, turn off the blades and proceed slowly straight down the slope.
DO NOT
1. Do not turn on slopes unless absolutely necessary, then only turn slowly and gradually downhill, if possible.
2. Do not mow drop–offs, ditches or embankments. A wheel over the edge or an edge caving in could cause a sudden overturn and an injury or death.
3. Do not mow on wet grass. Reduced traction could cause sliding.
4. Do not try to stabilize the machine by putting your foot on the ground.
5. Do not use a grass bagger or other rear mounted accessories on steep slopes (greater than 10 degrees).
III. Children
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. NEVER assume that children will remain where you last saw them.
1. Keep children out of the mowing area and in the watchful care of another responsible adult.
2. Be alert and turn the engine off if children enter the area.
3. Before and when backing, look behind and down for small children.
4. Never carry children or any passengers, even with the blades off. They may fall off and be seriously injured or interfere with the safe operation of the machine.
5. Never allow children to operate the machine. Instruct children in the potential dangers of the machine.
6. Use extra care when approaching blind corners, shrubs, trees or other objects that may obscure vision.
IV. Service
1. Use extra care when handling gasoline and other fuels. Fuels are flammable and the vapors are explosive. a. Use only an approved container. b. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool for several minutes before refueling. Do not smoke. c. Never refuel the machine indoors. d. Never store the machine with fuel in the tank or fuel container inside where there is an open flame, such as a water heater.
2. Never start or run the engine inside a closed area.
3. Keep all nuts and bolts, especially the blade attachment nuts tight. Frequently check the blade(s) for wear or damage such as cracks and nicks. A blade that is bent or damaged must be immediately replaced with an original equipment blade from an authorized service dealer. For safety, replace the blade every two years. Keep the equipment in good condition.
4. Never tamper with the safety devices. Check their proper operation regularly.
5. To reduce fire hazards, keep the machine free of grass, leaves or other debris build–up. Clean up oil or fuel spills. Allow the machine to cool before storing.
6. Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
7. Never make adjustments or repairs with the engine running. The carburetor can be adjusted with the engine running. Do not change the engine governor settings or over–speed the engine.
8. Grass bagger components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. For storage, always make sure the grass bag is empty. Frequently check components and replace with manufacturer’s recom­mended parts when necessary.
9. Mower blade(s) are sharp and can cut. Wrap the blade(s) or wear gloves and use extra caution when servicing them or the blade housing area.
10. Check the brake operation frequently. Adjust and service as required.
11. Wait for all movement to stop before servicing any part of the unit.
Look for this symbol to indicate important safety precautions. This symbol indicates: “Attention! Become Alert! Your Safety Is At Risk.”
F–040739L
4
SAFE MOWING GUIDE
Each person that operates power equipment must learn to use correct and safe mowing procedures. To help you
learn, carefully read the following pages. Most of the time the operator was
not correctly shown or did not read the instructions on the unit or in the Instruction Book before using the unit. Also, some operators do not have enough experience. The result is unsafe use, endangering the operator, bystanders and the equipment. Another result can be a poor appearance of the area mowed.
Read this book. Read the instructions on the unit. Operate the mower according to the Safe Mowing Guide. Follow all safety rules, cautions or warnings in this book and on the unit. Make sure anyone that uses the unit reads the instructions and is told how to safely operate the mower.
controls and how they work. In an emergency, how fast you can stop the blade is important. Learn how to control the mower at all times.
Many engines are started by hand. When you use a pull start or rope start, place your feet apart and away from the blade(s). Hold the rope handle tight. Never wrap the rope around your arm or fingers for a “better grip”. To start the engine, follow the instructions on the mower, in this book and in the engine operating instructions.
For electric start engines, sit in the seat to start the engine. The battery can be dangerous. Follow the instructions on the battery, the acid container, and in this book when working with the battery. Even small batteries have enough voltage to cause an injury. Always be careful.
The mower is designed to be operated by one person. Never let another person ride with you on the unit or on any accessories. A passenger will make the unit harder to control, block the visibility or distract the operator and is dangerous to the operator, the passenger and the equipment. Without a passenger seat, the passenger can fall from the mower or contact dangerous parts. A mower is not a toy for showing off or for giving rides.
The blade of a power mower rotates very fast. It can discharge rocks and other objects over a long distance which can be dangerous. The force of the objects can break windows, cause injuries or even put an eye out. Most of the time the injury is to a person, like a child. Keep every person completely away from the area to be mowed. Make sure the grass is not discharged toward anyone. Planning your mowing pattern has a double advantage. It can decrease the possibility of an injury and make the clean up after mowing easier.
The mower will give you good service and durability, if operated in normal conditions. If the mower is not correctly serviced or is used where the terrain is rough or unsuitable, product performance and safety will be decreased.
Correct clothing is an important part of safe mowing. Safety glasses will protect the eyes from objects discharged by the mower. Safety shoes with steel plates can protect a foot from injury by the blade. For protection from objects discharged from the mower, wear clothing that will cover the arms and legs.
Before you start cutting the grass, practice using the mower in a large open and level area. Learn the location of the controls on the mower. Know the purpose of the
F–040739L
Never cut a wet lawn. Wet grass can cause an accident, affect mower performance and can cause problems with future lawn growth and appearance. Wet grass is slippery and can cause the mower to slip. Someone can get injured by touching the blade(s). Wet grass tends to clog the mower, causing poor discharge. Cut wet grass will collect on the lawn, retarding the growth of the grass. Also, getting the mower wet will cause parts to rust and decrease the life of the unit.
When you look over the lawn, remember obstacles that cannot be removed, like pipes, stumps or rocks. Keep away from these obstacles that can cause damage to the mower or injury to the operator or a person near the mower. Clear the area of rocks, toys, wire or other loose objects. These items can damage the mower or can be discharged by the mower blade.
5
Check the terrain of the area to be mowed. Mow in a pattern that will keep you away from dangerous areas. Check the distance you need to stop and the distance available to turn. Slopes and rough terrain must be mowed carefully and some areas must not be mowed at all. With riding mowers, mow up and down the hill. When you must mow rough terrain or on slopes, drive slowly and stop in these areas only in an emergency. Before you ride up or down a slope, try to back straight up the slope. Do not ride up or down a slope that is too steep to back straight up. See the “Guide” in the back of this Instruction Book to check any slopes.
Before you start cutting, make sure the mower was completely assembled according to the Instruction Book. If the mower was completely assembled at the
SAFE MOWING GUIDE
store, you must still check the mower according to the assembly instructions. Make sure the mower is correctly assembled and that all fasteners are tight. Make sure the engine has the correct amount of oil. Check these items often during the life of the mower.
Your mower has a gasoline engine. Gasoline is a dangerous fuel. Keep gasoline only in an approved safety gasoline container. Do not keep large amounts of gasoline. When you add gasoline to the fuel tank, do not smoke. Store the gasoline container and the mower in an area that has good ventilation. Also, keep the gasoline away from any flames like the pilot light of a furnace or any other source of ignition. If the mower is to be stored for more than a few weeks, remove the gasoline from the fuel tank. When inside an enclosure, do not add gasoline to the fuel tank. Before you add gasoline, move the mower outside and add gasoline carefully. Before you start the engine, remove any gasoline from the outside of the fuel tank or from the mower. Warm gasoline will expand. Leave some space in the fuel tank for the gasoline to expand. Also, the fuel cap has a vent hole for fuel vapors. Always use the correct fuel cap. Failure to follow safety rules about gasoline will cause fires and explosions, injury to you and damage to the equipment and other property.
engine and transmission cool before servicing the mower. Remember, exhaust fumes are dangerous. Never operate the engine inside a building.
When you get a new mower, it can be a new experience for the family. Tell each person how a mower can be dangerous. Remember, a mower is not a toy. A mower is not to be used by children or anyone not old enough, strong enough or that does not have experience.
If the mower is not correctly assembled, not operated correctly, or not regularly serviced, the mower can be dangerous. The most important rule to follow is always use good judgement and common sense. Mow safely and carefully.
Your mower will easily cut thick grass. Fingers, feet and other parts can also be cut by the blade. Injuries occur when the operator does not think and reaches into the chute opening. Always operate the mower as if the blade is rotating. Do not service or make an adjustment, except to the carburetor, while the engine is running.
When you mow, remember that children are attracted to the mower. Always use caution when mowing around obstacles like trees or shrubs or when moving backward. Only mow in a forward direction if possible. Your visibility is decreased when you mow backward. Also, the blades are made to cut while the unit is moving forward. If you mow backward, the cutting performance decreases.
Before you leave the mower, stop the engine. Remove the key. Disengage and lower any attachment. Set the parking brake. Never mount or dismount from the seat while the engine is running. An accident can occur if you touch the brake, speed control pedal, throttle, or blade control while the engine is running. Mount and dismount from the seat on the side of the unit that is marked ENTER–EXIT.
If you add gasoline to an engine that is running or hot, the result can be an explosion. Before you add gasoline, stop the engine and let the engine cool for several minutes. Remove dry grass and other debris from the mower. Keep the mower clean to improve the performance, help the engine and transmission run cooler, extend the life of moving parts, and decrease the danger of a fire.
Fires and explosions are not the only dangers when working around a mower. The engine, transmission, and the muffler will get hot in several minutes when the engine is running. Do not touch these parts of the mower. Stop the engine. Let the
F–040739L
Use only accessories that are factory approved for your mower. The wrong accessory can decrease the safety of the mower and can even damage the unit. Read and follow the instructions included with the accessory and the mower.
Use only original equipment or replacement parts that are factory approved for service. If you need service, select an Authorized Service Center for your mower. If you do the work on the unit, follow the instructions in the Instruction Book.
6
Make sure you are in good condition when you mow. When you mow for several hours your reflexes will decrease and your mind will not be as alert. Take a short break or an accident can occur. If the temperature is hot, use caution to prevent dehydration. If you are tired, angry or not completely alert, do not operate the mower. If you use alcohol, medication or drugs, do not use the mower or any type of power equipment.
Engine speed is a key to safe mowing and to a good looking lawn. The maximum speed of the engine was set at the factory. Do not change the setting of the engine governor.
Select the maximum engine and ground speed that is right for the terrain and the height of the grass. The blade cuts best when the engine is operating at maximum speed. The engine and transmission will also run cooler at maximum engine speed.
SAFE MOWING GUIDE
Also, the grass bagger will function better when the engine is operating at maximum speed. On slopes, decrease the ground speed and use care making sure the mower feels safe to operate.
If the weather conditions are bad, do not mow. If weather conditions become bad, stop cutting and finish later. It is dangerous to cut grass in the rain. Always find protection in an electrical storm. If the weather conditions are extra dry, protect your eyes with safety glasses from the dust and from the objects discharged by the mower. Also, a dust or a pollen mask can help.
Your mower is equipped with a number of safety devices which are important to the safety of the operator and bystanders and must never be changed or removed from the mower. If a safety device is lost, damaged or no longer functions, repair or replace the device before you operate the mower.
It is best to mow during the day. If you must mow at night, make sure there is enough light for safe operation.
Your mower will require regular maintenance and service. The maintenance schedule depends on the hours of use. Also, mowing conditions can change the schedule. Check the Instruction Book for more information. Correct maintenance will help the mower function safely.
Do not service the mower (except for the carburetor adjustment) while the engine is running. Before you service the unit, even with the engine stopped, always disconnect the wire from the spark plug to prevent the engine from starting.
If you hit a large object during operation, stop the engine. Remove the wire from the spark plug. Carefully inspect the mower for damage. Before you start the engine again, make the necessary repairs. If you
feel new or excessive vibration, immediately stop the engine and check for the problem. Vibration can be a warning of a problem. Keep all nuts, bolts and screws tight.
The blade is the most dangerous part of the mower. Frequently check the blade and the blade mounting fasteners. Keep the fasteners tight. If the blade hits a solid object, stop the engine. Remove the wire from the spark plug. Check for a blade that is bent, cracked or for other damages. Before you start the engine, replace a damaged blade(s). For safety, replace the blade every two years.
A sharp blade decreases the workload on the engine and more evenly cuts grass. Frequently sharpen the blade for a better looking cut. Use the left side of the mower housing to trim near an object.
A grass bagger is a good accessory for your mower. For best performance and safety, make sure the grass bagger is approved for use with your mower. Follow the assembly and operation instructions included with the grass bagger.
Some grass baggers require a special blade for best performance. Before you attach, check, or empty the grass bagger, always stop the engine. Before each use of the grass bagger, check for cracks, wear or deterioration. Before you use the grass bagger, replace a damaged part with a replacement part approved by the factory.
For you to have a good green lawn, follow the mowing procedures below. Do not cut the grass too short. If you cut the grass too short you can cause the grass to become yellow or make the lawn look brown. Use a lower height of cut in cool months when the grass is thicker. Raise the height of cut in hot dry periods. If you cut the grass with
a blade that is not sharp or at a slow engine speed you can damage the grass. Move the throttle control to the FAST position when mowing and using the grass bagger. Also, use a slower ground speed when using the grass bagger.
If you change the direction or pattern of cut slightly every time you mow will make the grass grow stronger and thicker. Do not add oil or gasoline to the mower while on the lawn. Spilled oil or gasoline can kill the grass. In high or thick grass, do not try to cut all the grass the first time. Raise the height of cut on the first cutting and lower the height for the next cutting. Another way is to cut only part of the width of the mower and decrease your ground speed (not the engine) to move more slowly so that the mower can discharge the grass as it moves forward.
Understand the controls and how they work. Learn the ground speed(s) of your mower. Check the stopping distance required at different travel speeds. Check the turning radius of the mower. The controls on your riding mower are different from an automobile. The throttle is operated by hand and holds the engine speed constant until it is changed. The location of the travel speed control is different from that of an automobile. Also, the brake and clutch systems are different. Remember the procedures to follow in an emergency. Remember, turning off the engine ignition switch will stop the blade and the drive mechanism. If the traction of the wheels is lost or does not feel safe, disengage all systems and stop the engine. Dismount from the mower. Push the unit to a safe place before you begin mowing again.
Your unit has an electrical system that includes an operator presence switch in the seat. The operator presence switch detects if the operator is sitting on the seat. The engine will stop if the operator leaves the seat when the blade engagement control is engaged. This operator presence switch is a safety device only. It must not regularly be used to stop the engine or the blade. There are other control systems on the mower for this purpose. Always keep the operator presence switch and other safety devices and controls in place and operating for your protection.
Remember, your mower is a tool that can be dangerous if it is not correctly used. Follow the instructions in this Instruction Book. Safe and careful use of the mower will give you many safe hours of problem free use.
F–040739L
7
STEPS TO FOLLOW
BEFORE MOWING
F Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes.
F Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory replacement blade.
F Fill the fuel tank outside. Clean off spilled fuel.
F Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with any attachments. Owner’s Manual
instructions are for your safety and the safety of others.
F Exhaust fumes are dangerous. Start the engine outside.
F Make sure all safety devices are in place and working correctly.
F Operation of the mower is only for a person that has experience.
F Wet grass can be dangerous. Let the grass dry.
F Instruct children and others to keep away from the work area.
F Never cut the grass without good light.
F Pick up loose objects. Remove them from the mowing area.
WHILE MOWING
F Watch for fixed objects and avoid them. They can damage the mower or cause injury.
F A hot engine, muffler, and transmission will cause a burn. Do not touch.
F Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check a slope.
F Lack of daylight or good artificial light is cause to stop mowing.
F Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the unit vibrates excessively.
F Do not make adjustments or repairs without stopping the engine. Disconnect the spark plug wire.
F On or near roads, watch out for traffic. Direct discharge away from roads.
F When mowing, avoid areas where traction is unsure. Look back before changing direction of travel.
F In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass from the mower.
F Never remove any safety related parts.
F Do not pour gasoline into a engine that is hot or running.
AFTER MOWING
F Always let the mower cool before storing in an enclosed area.
F Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before storing.
F Tighten all loose nuts, bolts and screws before you use the unit.
F Empty and clean any grass catcher or other accessory.
F Remove the key or disconnect the spark plug wire to prevent unauthorized use.
F Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion.
F Only original parts or factory approved substitutes can be used to service the mower.
F When storing the mower for an extended period, remove the fuel from the fuel tank.
F Instruct children to leave the mower alone. It is not a toy.
F Never keep gasoline near a source of ignition. Always use an approved container. Keep gasoline away from children.
F Lubricate according to the Instruction Book. See “Lubrication”.
IMPORTANT––Read the Instruction Book. Keep this book for future use and reference.
WARNING: Look for this symbol to point out important safety precautions. It means: “Attention! Become Alert! Your Safety Is Involved.”
F–040739L
8
INTERNATIONAL PICTORIALS
INTERNATIONAL PICTORIALS
IMPORTANT: Some of the following pic­torials are located on your unit or on literature supplied with the product. Be­fore you operate the unit, learn and un­derstand the purpose for each pictorial.
Safety Warning Pictorials
1 Warning 2 Shield Eyes. Explosive Gases Can
Cause Blindness Or Injury.
3 No Sparks, Flames or Smoking. 4 Sulphuric Acid Can Cause Blindness
Or Severe Burns
12 3 546
5 Flush Eyes Immediately With Water.
Get Medical Help Fast.
6 IMPORTANT: Read Owner’s Manual
Before Operating This Machine.
7 WARNING: Thrown Objects. Keep
Bystanders Away. Read User Instructions Before Operating This Machine.
8 WARNING: Do Not Use This Machine
On Slopes Greater Than 15 Degrees.
9 DANGER: Keep People, Especially
Children, Away From Unit.
10 DANGER: No Step. 11 DANGER: Keep Feet And Hands
Away From Rotating Blade.
12 DANGER: Keep Hands Away From
Rotating Blade.
13 DANGER: Disconnect Spark Plug
Wire Before Servicing Unit.
14 WARNING: Hot Surface. 15 WARNING: Use Caution When
Connecting Or Disconnecting Accessories.
16 WARNING: Crushed Fingers.
1
7
12
Control And Operating Pictorials
1 Engine Start 2 Lights 3 Engine Stop 4 Engine Stop 5 Engine Run
1
2
13
3
8
6 Brake
7 Parking Brake
8 Clutch
9 Slow
10 Fast
9
14
10
MAX 90N+MAX 150N
+
15
11 Choke
12 Oil
13 Blade Rotation Control
14 Raise
15 Fuel
11
16
2
4
5
67
8
9
10 11 12
F–040739L
13
14
9
15
ASSEMBLY
ASSEMBLY
This instruction book is for several models. Some parts or accesso­ries are not included on all models. Read and follow the assembly and adjustment instructions for your mower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled.
NOTE: In this instruction book, left and right describe the loca­tion of a part with the operator on the seat.
WARNING: Before doing any assembly or mainte­nance to the mower, remove the wire from the spark plug.
PARTS BAG – CONTENTS
The fasteners and other loose parts are shown below. The fasteners are shown full size. The quantity is shown in brackets ( ).
2x82
(2) Carriage Bolt
14x79
(2) Wing Nut
17x91
(4) Washer
1001054 (2) Knob
31x11
(2) Hair Pin
17x47
(2) Washer
25x3
(1) Bolt
17x146
(1) Washer
20729
(1) Keys & Ring
F–040739L
10
ASSEMBLY
HOW TO INSTALL THE SEAT
Use the fasteners shown below to install the seat. The fasteners are shown at full size.
1. Carefully remove the plastic bag from the seat.
2. Align the holes in the seat
hinge to the holes in the seat (Figure 1). Fasten
the seat to the seat hinge with the fasteners as shown.
3. Check the operating posi­tion of the seat. If the seat needs to be adjusted, loosen the two wing bolts. Slide the seat for­ward or backward along the seat adjusting holes as shown. Tighten the
wing bolts (A).
(A)
1001054
(B)
17x47
Seat
Seat Hinge
Adjusting
Seat
Hole
B
A
Figure 1
HOW TO ASSEMBLE THE STEERING WHEEL
Use the fasteners shown below to install the steering wheel. The fasteners are shown at full size.
(A)
25x3
1. Make sure the front wheels point forward.
2. Slide the cover over the steering post (Figure 2).
3. Slide the steering wheel onto the steering post.
4. Apply firm pressure to center of the steering wheel with the palm of your hand until you hear a clicking noise. To check for proper locking of the steering wheel to the steering post, pull upward on steering wheel.
5. Use the fasteners shown above to secure the steering wheel. The fasteners are shown at full size. Tighten the screw. DO NOT over tighten.
(C)
17x146
HOW TO ASSEMBLE THE GAUGE WHEELS
Use the fasteners shown below to install the gauge wheels.
6. Remove adhesive backing from hub cover (found in parts bag) and place hub cover over hub.
Hub Cover
A
C
Steering Wheel
Cover
Steering Post
Figure 2
(A)
31x11
1. Attach the gauge wheels to the axle bolts with the fasteners.
NOTE: The axle bolt is mounted in the LOW position. To change the position to a higher cutting position, see “How To Adjust The Gauge Wheels” in the Maintenance section.
F–040739L
(B)
17x91
11
Axle Bolt
B
A
Gauge Wheel
Figure 3
ASSEMBLY
MAINTENANCE FREE BATTERY
IMPORTANT: Before you attach the battery cables to the battery, check the battery date. The battery date tells if the battery must be charged.
1. Check the top of the battery for the location of the battery date (Figure 4).
2. If the battery is put into service before the battery date, the battery cables can be attached without charging the battery. See “How To Install The Battery Cables”.
3. If the battery is put into service after the battery date, the battery must be charged. See “How To Charge The Maintenance Free Battery”.
HOW TO CHARGE THE MAINTENANCE FREE BATTERY
WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion.
1. Remove the battery and battery tray.
2. Remove the protective caps from the battery terminals.
3. Use a 12 volt battery charger to charge the battery. Charge at a rate of 6 amperes for one hour. If you do not have a battery charger, have an authorized service center charge the battery.
4. Install the battery and battery tray. Make sure the positive (+)
terminal is on the left side.
HOW TO INSTALL THE BATTERY CABLES
WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable.
Use the fasteners shown below to install the battery cables. The fasteners are shown at full size.
(A)
2x82
1. Remove the protective caps from the battery terminals.
2. Fasten the red cable to the positive (+) terminal with the fasteners as shown (Figure 4).
3. Fasten the black cable to the negative (–) terminal with the fasteners as shown.
(B)
14x79
B
Black Cable
Positive (+)
Terminal
A
Red Cable
A
Battery
Battery Tray
Figure 4
F–040739L
12
ASSEMBLY
IMPORTANT! BEFORE YOU START MOWING
- Check the engine oil.
- Fill the fuel tank with gasoline.
- Check the level of the mower housing.
- Check the air pressure of the tires.
- Make sure the battery cables are attached.
HOW TO PREPARE THE ENGINE
NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed.
See the engine manufacturer’s instructions for the type of gasoline and oil to use. Before you use the unit, read the information on safety, operation, maintenance, and storage.
WARNING: Follow the engine manufacturer’s instructions for the type of gasoline and oil to use. Always use a safety gasoline container. Do not smoke when adding gasoline to the engine. When inside an enclosure, do not fill with gasoline. Before you add gasoline, stop the engine. Let the engine cool for several minutes.
IMPORTANT: This unit is equipped with an internal combustion engine and must not be used on or near any unimproved
WARNING: Before doing any assembly or mainte­nance to the mower, remove the wire from the spark plug.
NOTE: In this instruction book, left and right describe the loca­tion of a part with the operator on the seat.
forest–covered, brush–covered or grass–covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. See an Authorized Service Center for a spark arrester for the muffler.
In some areas, local law requires the use of a resistor spark plug to control the ignition signals. See an Authorized Service Center for a resistor spark plug for the engine.
NOTE: Actual sustained horsepower will likely be lower due to operating limitations and environmental factors.
CHECK THE LEVEL OF THE MOWER HOUSING
Make sure the level of cut is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section of this instruction book.
CHECK THE TIRES
Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure (PSI) is 14 PSI (1 BAR). The tires were over inflated for shipment.
F–040739L
13
Throttle Control
Lever
Brake Pedal
OPERATION
Blade Rotation
Control
Speed Control
Pedal
Lift
Lever
LOCATION OF CONTROLS
BLADE ROTATION CONTROL: Use the blade rotation
control to start and stop the rotation of the blades.
BRAKE PEDAL: Use the brake pedal to quickly stop.
HEADLIGHT SWITCH: The headlight switch is the first part
of the ignition switch. To use the lights with the engine running, turn the key to the position for the lights.
Figure 5
AUTOMATIC DRIVE DISCONNECT: Use the auto-
matic drive disconnect, located under the seat, to disengage the transmission.
LIFT LEVER: Use the lift lever to change the height of cut.
PARKING BRAKE LEVER: Use the parking brake lever
to engage the brake when you leave the unit.
SPEED CONTROL PEDAL: Use the speed control pedal
to change the speed and the direction of the unit.
IGNITION SWITCH: Use the ignition switch to start and stop
the engine.
F–040739L
THROTTLE CONTROL LEVER: Use the throttle control
lever to increase or decrease the speed of the engine.
14
OPERATION
ATTACHMENTS
This unit can use many different attachments. See the attachment page in this book. This unit can pull attachments like a lawn sweeper, a lawn aerator, a hopper spreader or a small trailer. This unit can not use attachments that engage the ground like a plow, a disk harrow, or a cultivator.
For all pull–behind attachments or trailers, the maximum gross weight is 250 pounds. Gross weight is the weight of the attachment or trailer and any load that might be on or in it.
Do not operate on a slope that is greater than 10 degrees when using a pull–behind attachment or trailer. We have included a slope guide in this book to help you determine the slope on which you will be operating your unit. Never allow someone to stand or ride on or in an attachment or trailer.
HOW TO USE THE THROTTLE CONTROL
Use the throttle control to increase or decrease the speed of the engine.
CAUTION: Always operate the engine with the throttle control in the FAST position. If the engine runs for several minutes at slower than the FAST position, the engine and transmission will overheat and can be damaged.
1. The FAST position is marked with a detent. For normal opera­tion and when using a grass bagger, move the throttle control to the FAST position. For maximum charging of the battery and for a cooler running engine and transmission, operate the en­gine in the FAST position.
2. For transport and to tow pull behind attachments, control the ground speed with the speed control pedal.
3. The engine governor is set at the factory for maximum perform­ance. Do not adjust the governor to increase the speed of the engine.
HOW TO USE THE BLADE ROTATION CONTROL
The blade rotation control is next to the steering wheel (Figure 6). Use the blade rotation control to engage the blade(s) or to operate a snow thrower attachment.
1. Before you start the engine, make sure the blade rotation con- trol is in the DISENGAGE position.
2. Move the blade rotation control to the ENGAGE position to rotate the blade(s).
Note: If the engine stops when you engage the blade(s), the seat switch is not activated. Make sure you sit in the middle of the seat. Also, make sure the wire is connected to the seat switch.
3. Move the blade rotation control to the DISENGAGE position to stop the blade(s). Before you leave the operator’s position, make sure the blade(s) has stopped rotating.
4. Before you ride the unit across a sidewalk or a road, move the
blade rotation control to the DISENGAGE position.
WARNING: Always keep your hands and feet away from the blade, deflector opening, and the mower housing when the engine runs.
F–040739L
Disengage
Position
15
Blade Rotation Control
Engage Position
Figure 6
OPERATION
CHOKE
HOW TO USE THE SPEED CONTROL PEDAL
The drive system uses a Hydrostatic Automatic Drive transmission. The Hydrostatic transmission is very easy to operate. This type of drive system does not require a shift lever or a clutch pedal.
The speed and direction of travel is controlled by a single speed control pedal operated with your right foot. Do not use the left brake pedal in normal operation. Only use the left brake pedal to quickly stop in an emergency.
HOW TO DRIVE FORWARD
1. The automatic drive disconnect must be in the DRIVE position (Figure 8).
2. Slowly release your left foot from the brake pedal.
3. Move the throttle control to the FAST position.
4. Slowly push the speed control pedal forward to the desired speed (Figure 7).
5. To increase forward speed, slowly move the speed control
pedal forward. To reduce forward speed, slowly release the speed control pedal until the unit slows to the desired speed.
HOW TO DRIVE IN REVERSE
1. Look to the rear.
2. Slowly push the speed control pedal to the REVERSE position.
HOW TO CHANGE DIRECTIONS
CAUTION: To change directions, do not use the left brake pedal. Use only the speed control pedal.
1. Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL
position.
2. When the unit stops, slowly move the speed control pedal to the desired direction.
SPEED CONTROL PEDAL POSITIONS
The forward speed is controlled by the position of the speed control pedal. The following chart provides functions along with the pedal positions. Always operate the engine with the throttle control in the FAST position.
FUNCTION
Trimming Snow Thrower
PEDAL
POSITION
1/3
THROTTLE
Speed Control
Pedal
Figure 7
HOW TO DISCONNECT THE TRANSMISSION
To push the unit, use the automatic drive disconnect to release the transmission. The automatic drive disconnect is under the seat.
1. The engine must be off.
2. Raise the seat. The automatic drive disconnect is under the seat.
3. Move and latch the automatic drive disconnect in the PUSH position (Figure 8). The transmission is now released and the unit can be pushed.
NOTE: In cold weather, the heavy viscosity oil in the transmission will make the unit difficult to push.
4. To engage the transmission, unlatch the automatic drive dis­connect. The transmission is now connected and ready to op-
erate.
F–040739L
Bagging Grass 1/3 to 1/2
Normal Mowing 1/2 to 2/3
Easy Mowing Snow Blade
Transport FULL
Pull Behind Attachments
Automatic Drive Disconnect
PUSH POSITION
16
1/2 to 3/4
1/3 to 1/2
FAST
CHOKE
FAST
SLOW
THROTTLE
Seat
Automatic Drive Disconnect
DRIVE POSITION
Figure 8
OPERATION
HOW TO SET THE PARKING BRAKE
1. Completely push the brake pedal forward.
2. Lift the parking brake lever (Figure 9).
3. Remove your foot from the brake pedal and then release the parking brake lever. Make sure the parking brake will hold the unit.
4. To release the parking brake, completely push the brake pedal forward. The parking brake will automatically release.
WARNING: Before you leave the operator’s position, move the shift lever to the neutral (N) position. Set the parking brake. Move the blade rotation control to the DISENGAGE position. Stop the engine and remove the ignition key.
Parking
Brake
Figure 9
HOW TO CHANGE THE CUTTING HEIGHT
To change the cutting height, raise or lower the lift lever as follows.
1. Move the lift lever forward to lower the mower housing and back to raise the mower housing (Figure 10).
2. When you ride on a sidewalk or road, move the lift lever to the highest position and move the blade rotation control to the DISENGAGE position.
HOW TO STOP THE UNIT
1. Slowly remove your foot from the speed control pedal. The speed control pedal will automatically return to the NEUTRAL position and the unit will stop.
2. Move the blade rotation control to the DISENGAGE position.
3. Set the parking brake.
Lift Lever
Figure 10
WARNING: Make sure the parking brake will hold the unit.
4. Move the throttle control to the SLOW position.
5. To stop the engine, turn the ignition key to the OFF position. Remove the key.
HOW TO TRANSPORT THE UNIT
To transport the unit, follow the steps below.
1. Move the blade rotation control to the DISENGAGE position
2. Raise the lift lever to the highest position.
F–040739L
3. Move the throttle control to the FAST position.
4. Slowly push the speed control pedal forward to the desired speed.
17
OPERATION
HOW TO OPERATE WITH THE MOWER HOUSING
WARNING: The deflector is a safety device. Do not re­move the deflector. The deflector forces the dis­charged material toward the ground. Always keep the deflector in the down position. If the deflector is dam­aged, replace the deflector with an original equipment part from an authorized service center.
1. Start the engine.
2. Release the parking brake.
3. Move the lift lever to a height of cut position. In high or thick grass, cut the grass in the highest position first and then lower the mower housing to a lower position.
CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged.
4. Move the throttle control to the SLOW position.
5. Move the blade rotation control to the ENGAGE position.
6. Move the throttle control to the FAST position.
7. Slowly push the speed control pedal to the desired speed.
NOTE: When you mow in heavy grass or mow with a grass bagger, use a slow forward speed.
8. Make sure the level of cut set at the factory is still correct. After you mow a short distance, look at the area that was cut. If the mower housing does not cut level, see the instructions on “How To Level The Mower Housing” in the Maintenance section.
WARNING: For better control of the unit, always select a safe speed.
HOW TO OPERATE THE UNIT ON HILLS
WARNING: Do not ride up or down slopes that are too steep to back straight up. Never ride the unit across a slope. See the “Slope Guide” in the back of this book for information on how to check slopes.
HOW TO OPERATE ON A HILL
1. Control the speed only with the speed control pedal. Do not use the brake pedal on a hill.
2. To help prevent an accident, slowly move the speed control pedal. Avoid sudden turns or changes in speed.
3. To reduce forward speed when going down a hill, slowly release the speed control pedal until the unit slows to the desired speed.
HOW TO STOP ON A HILL
1. Avoid stopping on a hill. If you must quickly stop in an emergen­cy, remove your right foot from the speed control pedal and quickly depress the left brake pedal.
2. Set the parking brake.
3. Before you dismount from the seat, move the throttle control to SLOW position, move the blade rotation control to the DISEN­GAGED position, turn off the engine and set the parking brake.
HOW TO START OPERATION ON A HILL
1. Start the engine
2. Move the blade rotation control to the ENGAGED position.
3. Move the throttle control to the FAST position.
4. Depress the brake pedal and release the parking brake. As you release the parking brake, push the speed control pedal to the desired speed.
WARNING: Slowly push the speed control pedal as you release the parking brake. The parking brake must be disengaged before the speed control pedal is able to engage the transmission.
F–040739L
18
OPERATION
BEFORE STARTING THE ENGINE
CHECK THE OIL
NOTE: The engine was shipped from the factory filled with oil. Check the level of the oil. Add oil as needed. See the engine manufacturer’s instructions for the type of gasoline and oil to use.
1. Make sure the unit is level.
NOTE: Do not check the level of the oil while the engine runs.
2. Check the oil. Follow the procedure in the engine manufactur­er’s instructions.
3. If necessary, add oil until the oil reaches the FULL mark on the dipstick. The quantity of oil needed from ADD to FULL is shown on the dipstick. Do not add too much oil.
ADD GASOLINE
WARNING: Always use a safety gasoline container. Do not smoke when adding gasoline to the fuel tank. Do not add gasoline when you are inside an enclo­sure. Before you add gasoline, stop the engine and let the engine cool for several minutes.
Fill the fuel tank with regular unleaded gasoline. Do not use premium unleaded gasoline. Make sure the gasoline is fresh and clean. Leaded gasoline will increase deposits and shorten the life of the valves.
Full
Fuel Tank
CAUTION: A mixture of alcohol (ethanol or methanol) and gasoline (called gasohol), will attract moisture and cause acid deposits during storage. While the unit is in storage, the acids in the fuel can damage the fuel system.
To prevent engine problems with the fuel system, empty the fuel system before storage of 30 days or longer as follows.
1. Drain the fuel tank.
2. Start the engine. Let the engine run until the fuel lines and the carburetor are empty.
3. After storage, make sure you use fresh fuel. See the storage instructions for additional information.
4. Never use engine cleaner or carburetor cleaner in the fuel tank or permanent damage can occur.
CARBURETOR
The factory settings for the carburetor are for most conditions. If the engine is operated under the following conditions, you can adjust the carburetor mixture. To adjust the carburetor, see the engine manufacturer’s instructions.
1. The engine has a loss of power or does not run smooth.
2. A change from summer to winter operation.
3. A 40 degree change in the operation temperature. The carbure­tor was adjusted at 80 degrees at the factory.
4. The engine is operated above 4,000 feet.
HOW TO START THE ENGINE
WARNING: The electrical system has an operator presence system that includes a sensor switch for the seat. These components tell the electrical system if the operator is sitting on the seat. This system will stop the engine when the operator leaves the seat if the blade rotation control is engaged or if the trans­mission is engaged. For your protection, always make sure this system operates correctly.
NOTE: The engine will not start unless you depress the brake pedal or engage the parking brake and move the blade rotation control to the DISENGAGE position.
1. Push the brake pedal completely forward. Keep your foot on the pedal.
F–040739L
2. Make sure the blade rotation control is in the DISENGAGE position.
3. Move the throttle control completely forward to the CHOKE or FAST position. Some models have a separate choke knob. Pull the choke knob to the full CHOKE position.
4. Turn the ignition key to the START position. Release the key when the engine starts.
NOTE: If the engine does not start after four or five tries, see the TROUBLE SHOOTING CHART.
5. Slowly move the throttle control to the SLOW position.
6. Let a cold engine run for several minutes. Begin work when the engine is warm. To start a hot engine, move the throttle control to a position between FAST and SLOW.
19
OPERATING TIPS
OPERATION
1. Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly, the adjustment must be cor­rect.
2. Before you use the unit, check the oil in the engine and add oil if necessary.
3. If the engine will not start, first make sure the wire is attached to the spark plug.
4. Make sure all the belts are inside all the belt guides. See the in­structions on how to remove and install the motion drive and mower drive belts.
MOWING AND BAGGING TIPS
1. For a lawn to look better, check the cutting level of the mower housing. See “How To Level The Mower Housing” in the Main­tenance section.
2. For the mower housing to cut level, make sure the tires have the correct amount of air pressure.
3. Every time you use the unit, check the blade. If the blade is bent or damaged, immediately replace the blade. Also, make sure the nut for the blade is tight.
4. Keep the blade(s) sharpened. Worn blades will cause the ends of the grass to turn brown.
5. Before you make an inspection, adjustment (except for the car­buretor) or repair, make sure the wire from the spark plug is dis­connected.
6. For longer life of the battery on electric start models, charge the battery every three months.
7. Use the speed control pedal to change the ground speed, not the throttle control.
8. Belt noise can occur when the blade is engaged. This noise is normal and does not affect the operation of the unit.
10. For better engine performance and an even discharge of the cut grass, always operate the engine with the throttle in FAST position.
11. When you use a bagger, operate the engine with the throttle in FAST position and the speed control pedal pushed 1/3 forward.
12. For better cutting performance and a quality cut, mow with the speed control pedal pushed 1/3 to 1/2 forward.
13. After each use, clean the bottom and top of the mower housing for better performance. Also, a clean mower housing will help prevent a fire.
5. Do not cut or bag grass that is wet. Wet grass will not discharge correctly. Let the grass dry before cutting.
6. Use the left side of the mower housing to trim near an object.
7. Discharge the cut grass onto the mowed area. The result is a more even discharge of cut grass.
8. When you mow large areas, start by turning to the right so that the cut grass will discharge away from shrubs, fences, drive­ways, etc. After one or two rounds, mow in the opposite direc­tion making left turns until finished (Figure 11).
9. If the grass is very high, cut two times to decrease the load on the engine. First cut with the mower housing in the highest posi­tion and then lower the mower housing for the second cut.
F–040739L
Figure 11
20
MAINTENANCE
MAINTENANCE CHART
FREQUENCY MAINTENANCE REQUIRED COMMENTS
Daily or before each use
After completion of first 5 hours
After 25 hours Maintenance engine. Refer to the Engine Owner’s Manual.
Before storage of 30 days or more
Maintenance engine. Refer to the Engine Owner’s Manual.
Examine blade(s). Check for cracks, wear, and excessive
damage.
Remove debris from unit and mowing area.
Examine all rotating and sliding parts.
Check tire inflation. Refer to the Maintenance section.
Verify that the mower housing is level. Refer to the Maintenance section.
Examine V–belts. Check for cracks, wear, and excessive
damage.
Check brake operation. Refer to the Operation and Maintenance
sections.
Change oil. Refer to the Engine Owner’s Manual.
Remove, examine, sharpen, and balance
Refer to Maintenance section.
blade(s).
Check adjustments:
Refer to Maintenance section. a. Blade Rotation Control b. Brake c. Clutch d. Steering
Lubricate chassis and mower housing. Refer to Where to Lubricate instructions.
Check the muffler:
Refer to Maintenance section. a. Torque b. For wear or burn out c. Condition of spark arrestor, (if applicable).
Prepare engine for storage. Refer to the Engine Owner’s Manual.
Drain fuel system. Refer to warnings in the Owner’s Manual.
Add fuel stabilizer. Refer to the Engine Owner’s Manual.
Prepare battery for storage: a. Remove from unit. b. Fully charge. c. Move to cool dry place.
GENERAL RECOMMENDATIONS
1. The owner’s responsibility is to maintain this product. This will extend the life of the product and is also necessary to maintain warranty coverage.
2. Check the spark plug, drive brake, lubricate the unit, and clean the air filter once a year.
3. Check the fasteners. Make sure all fasteners are tight.
4. Follow the Maintenance section to keep the unit in good operat­ing condition.
WARNING: Before you make an inspection, adjust­ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.
F–040739L
NOTE: Torque is measured in foot pounds (metric Nm). This measurement describes how tight a nut or bolt must be. The torque is measured with a torque wrench.
HOW TO CHECK THE MUFFLER
Check the muffler every 50 hours. Make sure the muffler is correctly mounted and is not loose. If the muffler is worn or burnt, replace with a new muffler. A worn muffler is a fire hazard and can also damage the engine.
If you mount a spark arrester to the muffler, also check the spark arrester when you check the muffler. If the spark arrester is worn or damaged, replace it with a new spark arrester. See your nearest authorized service center for a spark arrester.
21
MAINTENANCE
INSPECT BLADE
WARNING: Before you inspect or remove the blade, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Check the unit for dam­age. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.
If you keep the blade sharp and inspect the blade for damage, the blade will cut better and be more safe to operate. Frequently check the blade for excessive wear, cracks, or other damage. Frequently check the nut that holds the blade. Keep the nut tight. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. See if the blade is bent or damaged. Check the blade adapter for damage. Before you operate the unit, replace damaged parts with original equipment parts. See the authorized service center in your area. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment part.
HOW TO REMOVE AND INSTALL THE BLADE
1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.
2. Use a piece of wood to keep the blade from rotating.
3. Remove the nut that holds the blade (Figure 12).
Hi–Lift
Edge Up
Mandrel
Blade Adapter
Blade
Belleville Washer
Washer
Nut
4. Check the blade and the blade adapter according to the in­structions for “Inspect Blade”. Replace a badly worn or dam­aged blade with an original equipment blade. See an authorized service center in your area.
5. Clean the top and bottom of the mower housing. Remove all the grass and debris.
6. Mount the blade and blade adapter on the mandrel (Figure 12).
7. Mount the blade so that the hi–lift edges are up. If the blade is upside down, the blade will not cut correctly and can cause an accident.
8. Fasten the blade with the original washers and nut. Make sure the outside rim of the Belleville washer is against the blade (Figure 13).
WARNING: Always keep the nut tight that holds the blade. A loose nut or blade can cause an accident.
F–040739L
Figure 12
9. Tighten the nut that holds the blade to a torque of 35 foot pounds (47,5 N–m).
10. Install the mower housing. See “How To Install The Mower Housing”.
Blade Adapter
Blade
Washer
Belleville Washer
(Outside rim must be
against the blade.)
Nut
Figure 13
HOW TO SHARPEN THE BLADE
WARNING: Vibration can be caused if the blade is not correctly balanced or if the blade is damaged. A blade that is damaged with cracks can break and cause an accident.
Keep a sharp edge on the blade. A blade that is not sharp will cause the tips of the grass to become brown.
1. Sharpen the blade two times a year or every 25 hours.
2. Remove the blade according to the instructions in “How To Re- move And Install The Blade”.
3. Clean the blade with a brush, soap and water. Check the blade. Look for cracks, nicks, or other damage. Replace a badly worn or damaged blade with an original equipment blade. See an authorized service center in your area.
4. Sharpen the blade with a file (Figure 14). Make sure you keep the original bevel angle.
5. Make sure the blade is balanced. Use a screwdriver and hold the blade parallel to the ground (Figure 14). A blade that is balanced will stay parallel to the ground. If the blade is not bal­anced, the heavy end will rotate toward the ground. Sharpen the heavy end until the blade is balanced.
6. A new blade will cut better than a badly worn blade. Every three years, have an authorized service person inspect the blade or replace the old blade with an original equipment blade.
7. Assemble the blade according to the instructions “How To Re­move And Install The Blade”.
Blade
Screwdriver
Blade is balanced
when parallel to the ground.
Ground
22
Figure 14
File
MAINTENANCE
HOW TO ADJUST THE BLADE ROTATION CONTROL
WARNING: To prevent an injury, the blade rotation control must operate correctly.
In normal usage, the blade rotation control will not require an adjustment. However, if the cutting performance decreases or the quality of cut is poor, make the following changes.
1. When you mow, make sure the throttle control in in the FAST position.
2. Move the blade rotation control to the DISENGAGE position (Figure 15).
3. Stop the engine. Disconnect the wire from the spark plug.
Disengage
Position
Blade Rotation Control
Engage Position
6. Attach the wire to the spark plug. Mow for a short distance and again check the quality of cut. If necessary, move the blade drive spring to the bottom hole.
7. Again check the quality of cut. If the quality of cut has not im­proved, replace the mower drive belt. See “How To Replace The Mower Drive Belt”. If replacing the belt does not correct the problem, take the unit to an authorized service center.
8. Move the blade rotation control to the DISENGAGE posi- tion. Stop the engine. Disconnect the wire from the spark plug. Check the operation of the blade brake. Rotate the pulleys with your hand. Make sure the brake pads are pressed tightly against the pulleys (Figure 17).
WARNING: If the brake pads do not press tightly against the pulleys, take the unit to an authorized service center.
Blade Brake
Brake Pad
Against Pulley
Figure 15
4. Check the blade(s). Keep a sharp edge on the blade(s). A blade that is not sharp will cause the tips of the grass to become brown.
5. Disconnect the blade drive spring from the blade control rod. Move the blade drive spring to the middle hole (Figure 16). This will increase the tension on the mower drive
belt.
DISENGAGE POSITION
Blade
Control Rod
Top Hole (New Belt)
Middle Hole
Bottom Hole
Figure 17
9. Move the blade rotation control to the ENGAGE position. Check the pads for the blade brake. If the pads are excessively worn or damaged, replace the brake pad assemblies. Correct replacement parts and assistance are available from an autho­rized service center.
10. Attach the wire to the spark plug. Mow for a short distance and again check the operation of the blade rotation control.
11. When you move the blade rotation control to the DISENGAGE position, all movement will stop within five se­conds. If there is movement of the belt or the blades continue to rotate, engage and disengage the blade rotation control five times to remove any excess rubber from a new mower drive belt. If you need assistance, take the unit to an autho­rized service center.
F–040739L
Blade Drive Spring
Figure 16
12. If you replace the mower drive belt, move the blade drive spring to the top hole (Figure 16).
23
MAINTENANCE
HOW TO CHECK AND ADJUST THE MOTION DRIVE BELT
If the motion drive belt is loose, the belt will slip when; (1) going up a hill, (2) pulling a heavy load, or (3) the unit will not move forward. Adjust the belt as follows.
WARNING: Before you make an inspection, adjust­ment, or repair to the unit, disconnect the wire to the spark plug. Remove the wire from the spark plug to prevent the engine from starting by accident.
1. Check the routing of the motion drive belt. Make sure the belt is installed correctly and is inside all the belt guides.
2. Disconnect the clutch link from the idler arm (Figure 18).
3. Align the hole in the brake lever with the hole in the frame. Hold the brake lever in place with a 1/4 inch (6 mm) pin or bolt (Figure 19).
4. Rotate the clutch link until the mounting hole in the clutch link is aligned with the hole in the idler arm as shown in Figure 18.
5. Connect the clutch link to the idler arm (Figure 18).
6. Remove the 1/4 inch (6 mm) pin or bolt (Figure 19).
7. If the belt still slips after the belt has been adjusted, then the motion drive belt is worn or damaged and must be replaced. See “How To Replace The Motion Drive Belt”.
Mounting
Holes
Clutch Rod
Clutch Link
Idler Arm
Figure 18
Clutch Link
Idler Arm
1/4” (6mm)
Pin or Bolt
Idler Spring
Belt Guide
Brake Lever
Motion Drive Belt
Figure 19
F–040739L
24
MAINTENANCE
HOW TO CHECK AND ADJUST THE DRIVE BRAKE
Completely push the brake pedal forward. Set the parking brake. Move the automatic drive disconnect to the PUSH position. Push the unit. If the rear wheels rotate, adjust or replace the brake pads. Adjust the drive brake as follows.
1. The location of the drive brake is on the right side of the gearbox (Figure 20).
2. Make sure the parking brake is set and the automatic drive disconnect is in the PUSH position. Turn the hex nut in a clockwise direction until the rear wheels do not turn when the unit is pushed forward.
3. Release the parking brake and push the unit. If the unit does not roll, turn the hex nut in a counterclockwise direction until the unit rolls.
4. Set the parking brake. Push the unit. If the rear wheels do not turn, the drive brake is correctly adjusted. Release the parking brake.
WARNING: If you cannot correctly adjust the drive brake, replace the brake pads. Correct replacement parts and assistance are available from an autho­rized service center.
MAINTENANCE FREE BATTERY
Drive Brake
Hex Nut
Gearbox
Figure 20
HOW TO REMOVE THE BATTERY
To charge or clean the battery, remove the battery from the unit as follows.
WARNING: To prevent sparks, disconnect the black battery cable from the negative (–) terminal before you disconnect the red cable. WARNING: The battery contains sulfuric acid which is harmful to the skin, eyes and clothing. If the acid gets on the body or clothing, wash with water.
1. Disconnect the black cable from the negative (–) terminal (Figure 21).
2. Disconnect the red cable from the positive (+) terminal.
3. Lift the battery tray and the battery out of the unit.
HOW TO CLEAN THE BATTERY
1. Remove the battery.
2. Wash the battery with a solution of one gallon of water and four tablespoons of baking soda (sodium bicarbonate). Make sure the solution does not get into the battery cells.
3. Clean the terminals and the ends of the cables with a wire brush.
4. Install the battery.
5. To prevent corrosion, apply grease to the battery terminals.
1. Before you charge the battery, remove the battery.
2. To charge the battery, use a 12 volt battery charger. Charge at a rate of 6 amperes for 1 hour.
3. Install the battery.
WARNING: To prevent sparks, fasten the red cable to the positive (+) terminal before you connect the black cable.
4. Fasten the red cable to the positive (+) terminal with the fas­teners as shown.
5. Fasten the black cable to the negative (–) terminal with the fas­teners as shown.
Positive (+)
Terminal
Wing Nut
Red Cable
Carriage Bolt
HOW TO CHARGE THE BATTERY
WARNING: When you charge the battery, do not smoke. Keep the battery away from any sparks. The fumes from the battery acid can cause an explosion.
F–040739L
25
Black Cable
Carriage Bolt
Battery
Battery Tray
Figure 21
MAINTENANCE
WHERE TO LUBRICATE
Models with grease fittings: Lubricate with grease gun.
Apply grease with a brush to the areas shown.
Lubricate the areas shown with engine oil.
NOTE: Apply grease to the steering gear assembly. CAUTION: If the unit is operated in dry areas that have sand, use a dry graphite spray to lubricate the unit.
HOW TO CHECK THE FUEL FILTER
NOTE: Before you replace the fuel filter or the fuel line, the fuel tank must be empty.
If the fuel filter is dirty, the engine will run rough and have less performance. Remove the old filter (Figure 23). Replace the old filter with a new filter. Use an original equipment part. See an authorized service dealer in your area.
CHECK THE TIRES
Check the air pressure in the tires. Tires with too much air pressure will cause the unit to ride rough. Also, the wrong air pressure will keep the mower housing from cutting level. The correct air pressure is 14 PSI (1 BAR).
F–040739L
Figure 22
Clips
Fuel Line
Fuel Filter
Figure 23
26
MAINTENANCE
HOW TO REMOVE THE MOWER HOUSING
1. Move the blade rotation control to the DISENGAGE position.
2. If equipped, remove the gauge wheels.
3. Move the lift lever to the level adjustment position(Figure 24).
WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUST­MENT position.
4. Remove the hair pins and the washers from the adjuster arms (Figure 25). See illustra­tions “C” and “D”.
5. Remove the hair pins and washers from the suspension links. See illustrations “A” and “B”.
6. Disconnect the extension spring from the blade control rod. See illustration “E”.
7. Disconnect the front hanger from the axle support. See illustration “F”.
8. Remove the mower drive belt from the stack pulley.
9. Pull the mower housing away from the right side of the unit.
10. To operate without the mower housing, move the lift lever to the TOP position.
A
Suspension
Link
Level Adjustment
Position Figure 24
Lift Lever
Blade Rotation
Control
HOW TO INSTALL THE MOWER HOUSING
1. Push the mower housing under the right side of the unit.
2. Put the mower drive belt around the stack pulley. Make sure the “V” side of the mower drive belt is against the stack pulley. Also, make sure the mower drive belt is not twisted.
3. Attach the front hanger to the axle support with the hanger rod. Fasten with the fasteners as shown. See illustration “F”.
4. Make sure the mower drive belt is between the stack pulley and the two belt guides. See illustration “G”.
5. Attach the suspension links to the lifter assembly. Fasten with the washers and hair pins. See illustrations “A” and “B”.
6. Attach the right and the left adjuster arms to the suspension brackets. Fasten with the washers and hair pins. See illustra­tions “C” and “D”.
7. Attach the extension spring to the blade control rod. See illustration “E”.
8. Move the blade rotation control to the ENGAGE position. Make sure the mower drive belt is inside all the belt guides.
9. Make sure the mower housing is level. See the instructions on “How To Level The Mower Housing”.
10. If equipped, install the gauge wheels.
11. Check the operation of the blade rotation control. See the in- structions on “How To Adjust The Blade Rotation Control”.
Stack Pulley
B
Suspension
Link
A
B
Adjuster
Arm
Belt
Guide
Mower Drive Belt
Belt
Guide
A
Lifter
Assembly
B
Adjuster
Arm
A
B
Blade
Control Rod
Hanger Rod
Extension
Spring
F–040739L
Front Hanger
Mower Drive Belt
Figure 25Gauge Wheel
27
MAINTENANCE
HOW TO ADJUST THE GAUGE WHEELS
The axle bolts for the gauge wheels were mounted in the LOW cut position. To change the position of the gauge wheels, move the axle bolts as follows.
IMPORTANT: Before you adjust the gauge wheels, you must do the following. Make sure the mower housing is level. Make sure the height of cut is set at the height you want for your lawn. Mow a short distance on a flat level area and look at the area that was cut. If the mower housing does not cut level, see the instructions “How To Level The Mower Housing.”
WARNING: Before you make an inspection, adjust­ment, or repair to the unit, disconnect the wire to the spark plug. Remove the spark plug wire to prevent the engine from starting by accident.
1. Remove the gauge wheels (Figure 26).
2. Mow a short distance on a flat level area to check the level of cut and the height of cut. Look at the height of cut position number on the lift lever (Figure 27).
3. Look at each gauge wheel bracket. There are 3 holes in each bracket and a number next to each hole. The number for the height of cut position on the lift lever indicates the correct hole to use on each gauge wheel bracket (Figure 28).
Locking
Ring
Washer
Axle Bolt
Gauge Wheel
Figure 26
Lift Lever
Cutting Height Positions
Figure 27
4. Assemble the axle bolts to the gauge wheel brackets using the correct hole in the bracket as indicated (Figure 28).
NOTE: If the height of cut position is changed by the lift lever, you must move the gauge wheels to the correct hole (Figure 28) to keep a level height of cut.
F–040739L
28
Gauge
Wheel Bracket
Wheel Bracket
Hole No.
1 1 2 2 3 3,4,5,6
Lift Lever
Position No.
Figure 28
MAINTENANCE
HOW TO LEVEL THE MOWER HOUSING
If the mower housing is level, the blade will cut easier and the lawn will look better.
WARNING: Before you make an inspection, adjust­ment, or repair to the unit, disconnect the wire to the spark plug. Remove the spark plug wire to prevent the engine from starting by accident.
1. Make sure the unit is on a hard flat surface.
2. Check the air pressure in the tires. If the air pressure is incor­rect, the mower housing will not cut level. Make sure the tires are inflated to 14 PSI. (1 BAR).
Lift Lever
Cover
Cutting Height Positions
IMPORTANT: On models equipped with gauge wheels, the gauge wheels must be removed to correctly adjust the level of the mower housing.
3. Some models have gauge wheels on the mower housing. If equipped, remove the gauge wheels.
4. Open the cover.
5. Move the lift lever to the LEVEL ADJUSTMENT position (Figure 29).
WARNING: The lift lever is spring loaded. Make sure the lift lever is locked in the LEVEL ADJUSTMENT position.
6. Loosen the left and right adjuster knobs (Figure 30). Push down on each side of the mower housing. Make sure both sides of the mower housing are setting on a flat surface. Also, make sure the lift links are loose and can easily move up or down.
7. Push down on the lift links and tighten the left and right adjust- er knobs (Figure 30). Make sure the adjuster knobs are tight. If necessary, use a wrench to tighten the adjuster knobs. For plastic adjuster knobs, tighten to a torque of 7 foot pounds (9,5 N–m). For metal adjuster knobs, tighten to a torque of 10 foot pounds (13,5 N–m).
Level Adjustment Position
Figure 29
Lift Link
Adjuster Knobs
Lift Lever
Figure 30
8. Raise the lift lever from the LEVEL ADJUSTMENT position to a CUTTING HEIGHT position (Figure 31).
9. Close the cover.
10. If equipped, install the gauge wheels.
11. Mow for a short distance. If the height of cut is not level, repeat the above steps.
CAUTION: Do not operate with the mower housing in the LEVEL ADJUSTMENT position. If you operate in the LEVEL ADJUSTMENT position, the mower housing and blades can be damaged.
F–040739L
Cover
Cutting Height Positions
Figure 31
29
MAINTENANCE
HOW TO REPLACE THE MOTION DRIVE BELT
REMOVAL
1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.
2. Remove the mid–idler pulley.
3. Disconnect the idler spring (Figure 34).
4. Remove the idler pulley and spacer (Figure 34).
5. Remove the V–idler pulley and spacer.
6. Remo ve the motion drive belt from the drive pulley (Figure 34).
7. To remove the motion drive belt from the stack pulley, pull the front end of the belt under the stack pulley and then back between the stack pulley and the steering plate (Figure 32).
8. Remove the access panel (Figure 33).
9. Remove the two screws that attach the steering shaft
assembly (Figure 33). Raise the steering wheel and steering shaft assembly. Pull the motion drive belt under the steering shaft assembly.
10. Remove the motion drive belt. A correct replacement part or assistance is available from an Authorized Service Center in your area.
INSTALLATION
1. Slide the motion drive belt between the stack pulley and the belt guides (Figure 32). Install the motion drive belt on the
top pulley of the stack pulley. Make sure the “V” side of the belt is against the pulley.
2. Push the motion drive belt through the opening between the steering plate and the engine plate.
3. Install the end of the motion drive belt around the drive pulley (Figure 34).
4. Put the motion drive belt around the V–idler pulley. Install the motion drive belt, V–idler pulley and spacer.
5. Put the belt around the idler pulley. Fasten the idler pulley and spacer with the hex nut. Make sure the flat side of the belt is against the idler pulley. Also, make sure the belt is not twisted.
6. Connect the idler spring (Figure 34).
7. Install the mid–idler pulley.
8. Check the routing of the motion drive belt (Figure 34). Make sure the motion drive belt is installed correctly on the idler pulleys and inside all belt guides.
9. Attach the steering shaft assembly to the steering plate with two screws (Figure 33).
10. Attach the access panel (Figure 33).
11. Before you use the unit, check the adjustment of the clutch. See the instructions “How To Check And Adjust The Clutch”.
12. Install the mower housing. See the instructions “How To Install The Mower Housing”.
FRONT
Stack Pulley
Motion
Drive
Belt
Steering Shaft
Assembly
Motion Drive
Belt
Screw
Access Panel
Steering
Plate
Belt Guides
Figure 32
Figure 33
Idler Pulley
Spacer
V–Idler Pulley
F–040739L
Drive Pulley
Idler Spring
Spacer
V–Idler Pulley
Idler Spring
30
Mid–Idler Pulley
Motion Drive Belt
Belt Guide
Belt Guide
Stack Pulley
Figure 34
MAINTENANCE
HOW TO REPLACE THE MOWER DRIVE BELT
1. Remove the mower housing. See the instructions on “How To Remove The Mower Housing”.
2. Pull the belt retainer away from the idler pulley and remove the mower drive belt (Figure 35).
3. Pull the belt retainer away from the right mandrel pulley and remove the mower drive belt.
4. Pull the belt retainer away from the left mandrel pulley and remove the mower drive belt.
NOTE: Replace the mower drive belt with an original equipment belt from an authorized service center.
5. Install the new mower drive belt. Pull the belt retainer away from the right mandrel pulley. Put the belt around the right
mandrel pulley.
6. Pull the belt retainer away from the left mandrel pulley. Put the belt around the left mandrel pulley.
7. Pull the belt retainer away from the idler pulley. Put the flat side of the mower drive belt around the idler pulley.
8. Make sure the “V” side of the mower drive belt is against the mandrel pulleys as shown.
9. Install the mower housing. See the instructions on “How To Install The Mower Housing”.
10. Before you mow, check the blade rotation control. See the in­structions on “How To Adjust The Blade Rotation Control”.
Belt Retainer
Left Mandrel Pulley
Belt Retainer
Belt Retainer
Right Mandrel Pulley
Idler Pulley
Figure 35Mower Drive Belt
F–040739L
31
MAINTENANCE
HOW TO INSTALL THE WHEELS
If the wheels must be removed for service, make sure they are installed as follows.
Front Wheel
1. Make sure the valve stem is to the outside of the tractor. Slide the front wheel on the spindle (See Figure 36).
2. Fasten the front wheel with washer and cotter pin. Bend the ends of the cotter pin apart to keep the front wheel on the
spindle.
3. If your model has hub caps, install the hub caps. Make sure the washer hold the hub caps in place.
Hub Cap
Valve Stem
Cotter Pin
Washer
Washer
Spindle
Front Wheel
Figure 36
Rear Wheel
1. Install the washers and spacer onto the axle as shown in Figure 37.
2. Mount the square key in the key slot (See Figure 37).
3. Make sure the valve stem is to the outside of the tractor. Align the slot in the rear wheel with the square key. Slide the rear wheel on the axle.
4. Fasten the rear wheel with washer and e–ring.
5. If your model has hub caps, install the hub caps. Make sure the washer hold the hub caps in place.
Rear Wheel
Hub Cap
E–Ring
Washer
Valve Stem
Square Key
Key Slot
Washer
Axle
Spacer
Figure 37
F–040739L
32
MAINTENANCE
HOW TO REPLACE THE FUSE
If the fuse is blown, the engine will not start. The location of the fuse is next to the battery. Remove the fuse and replace with a automotive fuse (Figure 38).
Automotive Fuse
Figure 38
HOW TO REPLACE THE LIGHT BULB
1. Raise the tractor hood.
2. Turn the light socket until the tabs on the socket align with the notches in the bezel (Figure 39). Remove the light socket. Turn the light bulb and remove the bulb.
HOW TO CLEAN THE MOWER HOUSING
WARNING: Before you clean the mower housing, stop the engine and disconnect the wire to the spark plug.
Grass and other debris on top of the mower housing can keep the belt from working correctly. For safety and correct operation, frequently clean the top of the mower housing. Remove grass and debris from around the pulleys and other moving parts.
3. Install a new light bulb. Align the light socket with the notches in the bezel and turn the light socket to lock in position.
Bezel
Light Bulb
Light Socket
1. Move the lever for the blade rotation control to the ENGAGE position.
2. Clean the top of the mower housing.
3. Move the lever for the blade rotation control to the DISENGAGE position.
4. Again clean the top of the mower housing.
5. After you cut the grass, clean the bottom of the mower housing.
Figure 39
STORAGE (over 30 days)
At the end of each year, prepare the unit for storage as follows.
THE ENGINE
For storage information, see the the engine manufacturer’s instructions.
THE BATTERY
1. Remove the battery.
2. Clean the battery terminals of any deposits.
3. Charge the battery. See the instructions on “How To Prepare And Charge The Battery”.
4. Store the battery in a cool, dry place.
NOTE: After a long time in storage, charge the battery.
THE FUEL SYSTEM
WARNING: Do not drain the gasoline inside a build­ing or near a fire. Do not smoke because the fumes from the fuel can cause an explosion.
F–040739L
1. Start the engine.
2. Run the engine until the fuel tank and the carburetor are out of fuel and the engine stops.
3. Do not leave fuel in the fuel tank or the carburetor. The fuel can damage the function of the fuel system. Some models have a fuel drain (Figure 40). Hold a cloth under the fuel drain. Push the fuel drain until the carburetor is empty.
4. After storage, make sure you use fresh fuel.
Fuel Drain
Figure 40
CLEAN THE UNIT
1. Clean the dirt and grass from the engine.
2. Clean the mower housing.
LUBRICATE THE UNIT
See the “Lubrication” instructions in this book.
33
TROUBLE SHOOTING CHART
PROBLEM: The engine will not start.
1. Follow the steps, “How To Start The Engine” in this book.
2. Electric–Start Models: Clean the battery terminals. Tighten the cables.
3. Drain the fuel tank. Clean the fuel line. Replace the fuel filter.
4. Remove the spark plug(s). Move the throttle to the SLOW posi­tion. Turn the ignition key to the ON position. Try to start the en­gine several times. Install the spark plug.
5. Replace the spark plug.
6. Adjust the carburetor.
PROBLEM: The engine will not turn over.
1. Follow the steps, “How To Start The Engine” in this book.
2. Electric–Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.
3. Replace the fuse.
4. Check the wiring harness for damage or a loose connection. Repair the damaged wire.
5. Electric–Start Models: replace the solenoid. Recoil–Start Mod­els: replace the module.
PROBLEM: The engine is difficult to start.
1. Adjust the carburetor.
2. Replace the spark plug.
3. Replace the fuel filter.
PROBLEM: The engine does not run smooth or has a loss of power.
1. Check the oil.
2. Clean the air filter.
3. Clean the air screen.
4. Replace the spark plug.
5. The engine is working too hard. Use a lower gear.
6. Adjust the carburetor.
7. Replace the fuel filter.
PROBLEM: The engine does not run smooth at fast speed.
1. Replace the spark plug.
2. Adjust the throttle control.
3. Clean the air filter.
4. Replace the fuel filter.
PROBLEM: The engine stops when the blades are engaged.
1. To activate the seat sensor, always sit in the middle of the seat.
2. Check the wiring harness for damage or a loose connection. Repair the damaged wire.
PROBLEM: On slopes, the engine stops.
1. Mow up and down slopes. Never mow across a slope.
2. To activate the seat sensor, always sit in the middle of the seat.
PROBLEM: The engine will not idle.
1. Replace the spark plug.
2. Clean the air filter.
3. Adjust the carburetor.
4. Adjust the throttle control.
5. Drain the fuel tank. Clean the fuel line. Replace the fuel filter.
PROBLEM: A hot engine causes a decrease in power.
1. Clean the air screen.
2. Check the oil.
3. Adjust the carburetor.
4. Replace the fuel filter.
PROBLEM: Excessive vibration.
1. Replace the blade.
2. Check for loose engine bolts.
3. Decrease the air pressure in the tires.
4. Adjust the carburetor.
5. Check for a damaged belt or damaged pulley. Replace the damaged parts.
PROBLEM: The grass does not discharge correctly.
1. Stop the engine. Clean the mower housing.
2. Raise the height of cut.
3. Replace or sharpen the blade(s).
4. Move the shift lever to a slower speed.
5. Move the throttle control to the FAST position.
6. Replace the spring for the blade idler.
PROBLEM: The mower housing does not cut level.
1. Check the air pressure in the tires.
2. Adjust the level of the mower housing.
3. Check the front axle. If the front axle does not freely pivot, loos­en the axle bolt(s).
PROBLEM: The mower blades will not rotate.
1. Check the mower drive belt. Make sure the belt is installed cor­rectly.
2. Replace the mower drive belt.
PROBLEM: The unit will not move when the brake is released and the speed control pedal is depressed.
1. Check the motion drive belt. Make sure the belt is installed correctly.
2. Adjust the clutch.
3. Replace the motion drive belt.
4. Release the Automatic Drive Disconnect under the seat.
PROBLEM: The unit moves slower or stops when the speed control pedal is depressed.
1. Adjust the clutch.
2. Replace the motion drive belt.
PROBLEM: When the brake pedal is released, belt noise can be heard.
1. Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.
2. If the noise is continuous, adjust the clutch.
PROBLEM: The rear wheels spin over uneven terrain.
1. Check the front axle. If the front axle does not freely pivot, loos­en the axle bolt(s).
F–040739L
34
Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where the unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow pages of the telephone directory.
If you cannot get a repair part or service as described above, call or write to the Central Parts Distributor shown below. When you order, include the following information: (1) Complete Model Number (see nameplate), (2) Date of Manufacture, (3) Complete Part Number, (4) Description, (5) Quantity. Repair parts for the engine or the transmission are available from the manufacturer's authorized service center found in the yellow pages of the telephone directory. See the individual engine or transmission warranties.
If you are unable to obtain parts or service in the manner outlined above, then contact:
USA MURRAY, INC., Outdoor Power Equipment, Customer Service Dept., P.O. Box 268, Brentwood, TN 37027 (1-800-251-8007) CANADA MURRAY CANADA, INC., Factory Customer Service, 1195 Coutneypark Drive East, Mississauga, Ont. L5T–1R1 (1-800-661-6662)
MURRAY, INC. LAWN MOWER CENTRAL PARTS DISTRIBUTORS
BILLIOU'S, INC.
1343 South Main St. Porterville, CA. 93257 (559) 784-4102 1-877-245-5468 FAX 1-800-226-7337
Arizona, California, Hawaii, Nevada
BROWN & WISER, INC.
9991 S.W. Avery Street Tualatin, OR. 97062 (503) 692-0330 1-800-882-4782 FAX (503) 691-2041 Alaska, Idaho (counties Ada, Adams, Benewah, Boise, Bonner, Boundry, Canyon, Clearwater, Elmore, Gem, Idaho, Kooten, Latah, Lewis, Nez Perce, Owyee, Payette, Ravalli, Shoshone, Valley, Washington), Montana (counties Flathead, Lake, Lincoln, Mineral, Missoulo, Ravalli, Sanders), Oregon,
Washington
CPT CANADA POWER TECHNOLOGY LIMITED
Mississauga
161 Watline Avenue Mississauga, Ontario L4Z-1P2 (905) 890-6900 1-800-861-9559
Edmonton
101-10411-178th Street Edmonton, Alberta T5S 1R5 (780) 453-5791 1-800-861-9559
FRANK EDWARDS CO.
3626 Parkway Blvd. West Valley, UT 84120 1-800-318-0201 FAX 1-801-736-8067 Colorado, Idaho (counties Bannock Bearlake, Bingham, Blaine, Booneville, Butte, Camas, Caribou, Cassia, Custer, Franklin, Fremont, Gooding, Jefferson, Jerome, Lemhi, Lincoln, Madison, Minidoka, Oneida, Power, Teton, Twin Falls) Montana (all counties except Flathead, Lake, Lincoln, Mineral, Missoulo, Ravalli, and Sanders), Utah, Wyoming
GARDNER, INC.
3641 Interchange Road Columbus, OH. 43204-1499 1-800-848-8946 FAX 1-800-626-4735
Alabama, Arkansas (except these counties: Hempstead, Howard, Lafayette, Little River, Miller, Nevada, Pike, Sevier), Connecticut,
Delaware, District of Columbia, Florida, Georgia, Illinois (South of Hwy. 80),, Indiana, Iowa, Kansas, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan (except upper Peninsula), Mississippi, Missouri, Nebraska, New Hampshire, New Jersey, New York, North Carolina, Ohio, Pennsylvania, Rhode Island, South Carolina, Tennessee, Vermont, Virgina, West Virginia
Puerto Rico
GULF COAST ENGINE, INC.
4202 Russell Dr. Corpus Christi, TX. 78408 1-800-825-6999 FAX 1-888-888-7036 Arkansas (counties Hempstead, Howard, Lafayette, Little River, Miller, Nevada, Pike, Sevier) New Mexico, Oklahoma, Texas,
Mexico
WISCONSIN MAGNETO, INC.
4727 N. Teutonia Ave. Milwaukee, WI. 53209 1-800-733-7388 FAX 1-800-733-0127 Illinois (N. of Hwy. 80), Michigan (upper Peninsula), Minnesota, North & South
Dakota, Wisconsin
Ville St-Laurent
234 Migneron Street Ville St-Laurent, Quebec H4T 1Y7 (514) 731-3559 1-800-861-9559
Canada
F–040739L
35
REPAIR PARTSMODEL 425619x24B
CHASSIS & HOOD
19
17
18
13
14
15
16
12
48
11
70
10
47
20
57
2
3 4
58
30
32
8
7
9
2
24
55
56
22
21
50
23
6
5
58
55
33
59
34
25
31
29
1
31
27
28
16
16
16
46
16
43
44
16
52
45
36
35
31
42
49
16
16
37
38
41
16
53
26
51
39
40
F–040739L
36
REPAIR PARTSMODEL 425619x24B
CHASSIS & HOOD
Key
No. Part No. Description
1 1001028 Seat
2 028x23 Cap, Push 0n
3 094057 Spring
4 26x229 Screw
5 1001054 Bolt, Wing
6 017x47 Washer
7 009x56 Bolt, Shoulder
8 094154E701 Support, Seat
9 094156 Z Rod, Pivot
10 1001648E700 Bracket, Pivot
11 001x45 Bolt
12 015x89 Nut
13 009x55 Bolt, Shoulder
14 094155 Z Washer
Key
No. Part No. Description
32 26x238 Screw
33 1001491 Bearing, Steering
34 1001594E700 Dash
35 26x201 Screw
36 093007E701 Panel, Access
37 095318E700 Support, Dash
38 1001270E701 Bracket, Rear Hanger
39 094085E700 Support, Left Grille
40 094007E701 Axle, Hanger
41 094084E700 Support, Right Grille
42 009x58 Bolt, Shoulder
43 1001928E701 Frame, Right
44 1001927E701 Frame, Left
45 690424 Container, Battery
15 164x31 Spring
16 26x249 Screw
17 26x263 Screw
18 164x30 Spring
19 1001556E549 Deck, Seat
20 15x123 Nut
21 094194E701 Plate, Index
22 009x47 Screw
23 095408 Mat, Left
24 095409 Mat, Right
25 1001539E549 Hood
26 1001533E549 Grille
27 1001552 Lens, Left
28 1001550 Housing, Left Headlamp
29 1001551 Lens, Right
46 1001002E701 Plate, Hitch
47 1001906E700 Plate, Rear
48 094186E700 Top, Rear Plate
49 26x277 Screw
50 015x81 Nut
51 15x124 Nut
52 690482E701 Support, Battery
53 1001540 Insert, Grille
55 0193x1 Fastener, Panel
56 094680 Cover, Detent
57 1001652 Trim, Hood (3.75”)
58 1001653 Trim, Hood (6.5”)
59 1001755 Grommet, Parking Brake
70 1001542 Holder, Cup
–– 1001599 Bag Assembly, PArts
30 1001549 Housing, Right Headlamp
31 26x270 Screw
F–040739L
–– 240214x00 Utility Cart
–– F–040739L Instruction Book & Parts List
37
54
REPAIR PARTSMODEL 425619x24B
DRIVE ASSEMBLY
1
2
52
53
45
44
47
43
46
42
7
8
41
40
56
39
55
38
40
37
48
41
39
1
51
1
50
49
34
1
4
5
1
6
9
10
11
F–040739L
58
25
16
36
57
35
26
24
23
22
34
21
38
32
33
31
30
29
2827
20
19
17
18
19
16
1
14
12
59
15
9
REPAIR PARTSMODEL 425619x24B
DRIVE ASSEMBLY
Key
No. Part No. Description
1 26x249 Screw
2 091079 Grip, Parking Brake
4 1001245 Z Rod, Parking Brake
5 094185E701 Bracket, Transaxle – Left
6 1001013 Z Rod, Clutch
7 094045 Z Latch, Parking Brake
8 37x106 V–Belt, Drive
9 015x79 Nut, Flange
10 021544 Pedal, Brake/Clutch
11 1001011E701 Assembly, Brake Pedal
12 094384 Screw, Guide
14 002x53 Bolt, Carriage
15 017x57 Washer
16 0031x4 Pin, Hair
Key
No. Part No. Description
31 015x84 Nut, Centerlock
32 030x20 Pin, Cotter
33 017x48 Washer
34 165x92 Spring, Extension
35 17x148 Washer
36 1001086 Z Arm, Disconnect
37 06x105 Capscrew
38 165x150 Spring, Brake
39 015x98 Locknut, Flange
40 690409 Pulley, Idler
41 690369 Spacer
42 1001097E701 Bracket, Idler Assembly
43 009x49 Bolt, Shoulder
44 1001007 Z Link, Clutch
17 1001231E701 Pedal Assembly, Hydro
18 092511–601 Wheel & Tire Ass’y –Rear 20”
– – 407926 Tire ONLY *
– – 407049 Tube ONLY
19 17x160 Washer
20 690554 Z Spacer
21 024373 Stem, Valve
22 17x195 Washer
23 0011x3 E–Ring
24 094618 Cap, Hub
25 015x88 Nut, Centerlock
26 * * Transaxle
27 1001085E701 Strap, Torque
28 26x216 Screw
29 1001234 Z Rod, Control
45 1001014 Nut, Tee
46 690410 Pulley, Idler
47 1001012 Bushing, Pivot
48 1001018 Z Arm Assembly, Idler
49 094184E701 Bracket, Transaxle –Right
50 01x155 Bolt, Hex
51 1001214 Z Bracket, Disconnect
52 1001215 Z Rod, Disconnect
53 1001108E701 Bracket, Idler Pivot
54 002x92 Bolt, Carriage
55 002x78 Bolt, Carriage
56 165x155 Spring, Clutch
57 017x38 Washer
58 021553 Key, Square 3/16
59 094953 Pad, Hydro Pedal
30 092132 Z Nut, Adjusting
* When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match. ** For information on Replacement Parts for this transaxle contact the manufacturer.
F–040739L
39
REPAIR PARTSMODEL 425619x24B
STEERING
3
41
43
2
1
30
13
6
40
39
19
31
30
34
33
30
30
4
5
6
12
7
8
9
10
11
25
31
15
16
25
28
29
24
14
30
19
26
22
27
23
25
22
23
17
18
30
37
20
20
21
24
38
F–040739L
36
35
32
25
40
REPAIR PARTSMODEL 425619x24B
STEERING
Key
No. Part No. Description
1 1001226 Wheel, Steering
2 690625 Post, Steering
3 1001441 Cap, Steering Wheel
4 094124 Bearing
5 15x111 Nut, Flange
6 009x57 Bolt, Shoulder
7 690183 Gear, Pinion
8 011x25 Ring, Snap
9 094121 Gear, Sector
10 094123 Bearing
11 001x84 Bolt
Key
No. Part No. Description
23 17x104 Washer
24 017x53 Z Washer
25 015x84 Nut, Flange
26 1001460E701 Axle Assembly
27 095329E701 Drag Link, Left
28 094575E701 Spindle Assembly, Right
29 095328E701 Drag Link, Right
30 26x249 Screw
31 091334 Bearing, Wheel
32 024373 Stem, Valve
33 024380 Tire *
12 1001121E701 Plate, Steering
13 094006E700 Plate, Engine
14 015x88 Nut, Flange
15 15x118 Nut, Flange
16 1001270E701 Bracket, Hanger
17 094007E701 Axle, Hanger
18 01x146 Bolt
19 030x49 Pin, Cotter
20 690150 Bearing
21 094576E701 Spindle Assembly, Left
22 01x111 Bolt
* When you order a tire, make sure to give the brand name of the tire so that the tread pattern on the tire will match.
–– 407924 Tube
34 094581–601 Wheel and Tire Assembly
35 17x195 Washer
36 17x192 Washer
37 17x113 Washer
38 094618 Hub Cap
39 26x267 Screw
40 092059 Bellows
41 0025x3 Bolt
43 17x146 Washer
F–040739L
41
MOWER HOUSING SUSPENSION
2
4
21
14
22
24 24
17
3
REPAIR PARTSMODEL 425619x24B
11
12
10
11
18
5
1
16
9
15
14
15
13
12
24
14
25
22
27
20
32
37
26
26
36
34
11
45
20
33
25
19
32
39
30
23
38
31
40
24
8
6
7
43
25
F–040739L
31
24
44
25
30
42
39
15
41
42
7
24
15
REPAIR PARTSMODEL 425619x24B
MOWER HOUSING SUSPENSION
Key
No. Part No. Description
1 092698 Grip
2 094826 Z Handle, PTO
3 094022 Z Pad, Switch
4 0025x3 Bolt
5 092697 Grip
6 166x40 Spring
7 17x103 Washer
8 690533 Lever, Lift
9 094017 Z Lever, PTO
10 009x39 Bolt, Shoulder
11 030x20 Pin, Cotter
Key
No. Part No. Description
22 17x168 Washer
23 017x57 Washer
24 0031x4 Pin, Hair
25 017x91 Z Washer
26 002x85 Bolt, Carriage
27 1001111E700 Lever Assembly, Lift
30 094067 Pin
31 094055E701 Bracket, Rear Suspension
32 690151 Spacer, Lifter
33 009x53 Bolt, Shoulder
34 094015E700 Bracket, Pivot
12 017x57 Washer
13 094004 Z Link, PTO
14 015x84 Nut, Flange
15 26x249 Screw
16 166x39 Spring
17 094018E701 Bracket, PTO
18 165x119 Spring
19 690394E701 Crank, PTO
20 690212E701 Link, Lift
21 690122E701 Link, Lift Handle
36 17x191 Washer
37 015x84 Nut, Flange
38 165x131 Spring
39 015x68 Nut, Flange
40 094005E700 Bracket, PTO
41 094027E700 Hanger, Left Deck
42 094026E700 Hanger, Right Deck
43 094158 Z Rod, Hanger
44 690539E701 Bracket, Suspension
45 1001098E701 Plate, Stiffening
F–040739L
43
4
53
60
REPAIR PARTSMODEL 425619x24B
MOWER HOUSING
2
3
2
61
17 1
62
5
10
47
13
33
14
31
32
29
50
11
51
1
55
24
52
20
8
19
17
9
15
5
32
22
23
30
22
21
5
48
22
24
25
27
22
5
5
23
32
49
24
12
28
5
26
22
17
17
22
21
4
5
9
8
19
20
5
23
46
11
22
18
23
10
59
15
13
47
1
16
17
33
53
51
60
F–040739L
64
50
54
33
22
44
5
43
42
65
66
33
32
42
41
36
40
38
39
45
34
44
37
33
36
38
39
33
40
5
34
7
58
57
35
37
REPAIR PARTSMODEL 425619x24B
MOWER HOUSING
Key
No. Part No. Description
1 094199 Pulley, Jackshaft
2 15x140 Nut, Hex
3 037x88 Belt, Mower Drive
4 690387 Pulley, Idler
5 015x84 Nut, Flange
7 009x58 Bolt
8 690212E701 Link, Lift
9 094137 Pad, Friction
10 009x52 Bolt, Shoulder
11 094055E701 Bracket, Suspension
12 094049E701 Pad Assembly, Left Brake
13 094068 Knob
14 009x51 Bolt, Shoulder
15 094128E700 Plate, Suspension
16 166x43 Spring
Key
No. Part No. Description
34 1001200 Mandrell Housing
35 690539E701 Bracket, Suspension
36 690411 Adapter, Blade
37 095100E701 Blade
38 17x166 Washer
39 17x165 Washer
40 15x100 Nut
41 0166x4 Spring
42 028x23 Cap, Push On
43 094957 Z Rod, Deflector
44 094707SE Deflector Assembly
45 094956E701 Bracket, Deflector Hinge
46 094190E701 Bracket, Front Hanger
47 017x45 Washer
48 094781 Guide, Belt
17 015x79 Nut, Flange
18 094192E700 Bracket, Suspension
19 095194 Pin, Hanger
20 017x91 Washer
21 0031x4 Pin, Hair
22 0025x7 Bolt
23 094051E701 Cover, Pulley
24 009x39 Bolt, Shoulder
25 690408E700 Arm, Idler
26 166x41 Spring
27 094047E701 Pad Assembly, Right Brake
28 094193E700 Bracket, Brake
29 166x42 Spring
30 094191E700 Bracket, Suspension
31 092426E700 Plate
32 015x88 Nut, Flange
33 002x53 Bolt, Carriage
49 690369 Spacer
50 094025 Bolt, Axle
51 017x91 Washer
52 165x119 Spring, Extension
53 092683 Wheel, Gage
54 1001260E700 Bracket, Right Wheel
55 092423E700 Bracket, Left Wheel
57 26x249 Screw
58 094604E700 Stiffener
59 094814E700 Housing, Blade *
60 031x11 Ring, Locking
61 015x98 Nut, Flange
1–61 7601032 Complete Mower Housing Assy
62 094066 Guide, Belt
64 095080E701 Cover, Mulch
65 002x64 Bolt
66 014x86 Wingnut
* Includes Key No. 17, 18, 30, 31, 32, 33, 45, 46, 53, 54, 55, and 56.
F–040739L
45
26
8
REPAIR PARTSMODEL 425619x24B
ENGINE MOUNT
1
2
3
4
5
6
9
9b
9c
9b
15
32
30
15
9f
9e
31
9a
22
9d
21
10
7
22
21
23
23
F–040739L
46
11
14
13
12
Key
No. Part No. Description
1 092317 Fuel Cap **
2 690280 Fuel Tank
3 095197 Hose Clamp **
4 7601033 Fuel Line (Must cut to length) **
5 095197 Hose Clamp **
6 26x201 Screw
7 094006E700 Plate, Engine
8 092371 Throttle Control
9 * Engine, BRIGGS & STRATTON
9a 1001717 Muffler
REPAIR PARTSMODEL 425619x24B
ENGINE MOUNT
9b 091309 Gasket, Muffler
9c 095207 Adapter, Muffler
9d 06x103 Screw, Adapter
9e 009x59 Bolt, Muffler
9f 092378 Lock, Screw
10 0025x7 Bolt, Engine Mount
11 690439 Z Stack Pulley Assembly
12 019x35 Lockwasher
13 1x140 Bolt, Hex
14 17x170 Washer
15 26x249 Screw
21 094384 Guide, Belt
22 015x79 Z Nut, Flange
23 094066 Guide, Belt
26 26x253 Screw
30 1001897 Shield, Heat
F–040739L
31 26x263 Screw
32 06x104 Screw
* For information on Replacement Parts for this engine contact the manufacturer.
* * These parts are included with Key number 2.
47
REPAIR PARTSMODEL 425619x24B
ELECTRICAL SYSTEM
1
92556
2
11
6
24x31
94613
REAR HARNESS: 250X67
LIGHT HARNESS: 250X92
MAIN HARNESS: 250x117
5
94136
3
10
94136
4
F–040739L
7
24x32
21075
8
94159
9
48
ELECTRICAL SYSTEM
Key
No. Part No. Description
1 250x92 Harness, Light Wire
1001716 Socket, Light
090084 Bulb, Light
2 250x117 Harness, Chassis Wire
3 092556 Switch, Ignition
020729 Key, Ignition 091489 Nut, Hex
091488 Cap, Ignition
4 094136 Switch, Limit
REPAIR PARTSMODEL 425619x24B
5 302031 Fuse
407078 Holder, Fuse
6 094613 Solenoid
26x229 Screw, Mounting
15x116 Locknut
7 024x32 Cable, Battery Ground
26x229 Screw, Ground Cable
8 021075 Battery
002x82 Bolt, Carriage
014x79 Wingnut
9 250x67 Harness, Seat Switch Wire
10 094159 Switch, Seat Sensor
11 024x31 Cable
F–040739L
49
F–040739L
50
INDEX
A
Adjustments
Blade Rotation Control, 23 Clutch, 24 Drive Brake, 25 Mower Housing, Level, 29
Attachments, 15, 52 Automatic Drive Disconnect,
Operation, 16
B
Battery
Charge, 25 Check, 12 Clean, 25 Install, 12 Removal, 25 Storage, 33
Belt
Motion Drive
Adjust, 24 Replace, 30
Mower Drive
Adjust, 23 Replace, 31
Blade
Inspect, 22 Remove And Install, 22 Sharpen, 22
Blade Rotation Control
Adjust, 23 Location, 14 Operation, 15
Brake Pedal, Location, 14
C
Clutch
Adjust, 24 Check, 24
Controls, Location, 14 Cutting Height
Adjust, 29 Change, 17
D
Drive Brake
Adjust, 25 Check, 25
E
Engine
Fuel, 13, 19 Oil, 13, 19 Preparation, 13 Spark Arrester, 13, 21 Starting, 19 Storage, 33
Throttle Control, 15
F
Filter, Fuel, 26 Fuel, Type, 19 Fuse, 33
H
Headlight, Replace Light Bulb, 33 Headlight Switch, Location, 14
I
Ignition Switch, Location, 14
L
Lift Lever
Location, 14 Operation, 17
Lubrication, Mower, 26
M
Maintenance
Adjust, Guage Wheels, 28 Battery
Charge, 25 Clean, 25
Belt
Motion Drive, 30
Mower Drive, 31 Blade, 22 Blade Rotation Control, 23 Clutch, 24 Drive Brake, 25 Filter, Fuel, 26 Fuse, 33 Headlight, 33 Install, Wheels, 32 Lubrication, 26 Mower Housing
Clean, 33
Install, 27
Level, 29
Remove, 27 Muffler, 21 Storage, 33
Maintenance Chart, 21 Motion Drive Belt
Adjust, 24 Replace, 30
Mower Drive Belt
Adjust, 23 Replace, 31
Mower Housing
Clean, 33 Cutting Height, 17 Install, 27 Level Adjustment, 29
Operation, 18 Remove, 27
Muffler, 21
Spark Arrester, 21
O
Oil
Check, 19 Type, 19
Operation
Attachments, 15 Automatic Drive Disconnect, 16 Blade Rotation Control, 14, 15 Brake Pedal, 14 Headlight Switch, 14 Ignition Switch, 14 Lift Lever, 14, 17 Location Of Controls, 14 Mower Housing, 18 Mowing And Bagging, 20 Operate On Hills, 18 Parking Brake, 14, 17 Speed Control Pedal, 14, 16 Start The Engine, 19 Stop The Unit, 17 Throttle Control, 14, 15 Transport, 17
P
Parking Brake
Location, 14 Operation, 17
Parts Bag, 10
S
Safety Rules
American National Standard Institute, 3–4
Safe Mowing Guide, 5–7 Seat, Install, 11 Seat Switch, Operation, 19 Slope Guide, 50
Spark Arrester, 13, 21 Speed Control Pedal
Location, 14
Operation, 16 Steering Wheel, 11 Storage, 33
T
Throttle Control
Location, 14
Operation, 15 Tire Pressure, 13, 26
Trouble Shooting Chart, 34
W
Warranty, 2
F–040739L
51
LAWN TRACTOR ACCESSORIES
Make your Lawn Tractor do more than you ever imagined.
The accessories shown on this page can be used on your Lawn Tractor. See the Store or Dealer where you purchased your Lawn Tractor. If you are unable to obtain the necessary information, contact the Central Parts Distribution Center for your area as listed in your Repair Parts Book.
LAWN SWEEPER Model No. 24720
GRASS BAGGER Model No. 24767 9 Bushel Capacity
(For 42” and 46”)
38” MULCHER KIT Model No. 24750
40” MULCHER KIT Model No. 24755
SNOW BLADE Model No. 24478
SNOW THROWER Model No. 24574
GARDEN TILLER Model No. 13460
F–040739L
42” MULCHER KIT Model No. 24758
TIRE CHAINS Model No. 24530
(For 18x8.5 inch tire)
Model No. 24538
(For 18x9.5 inch tires)
Model No. 24525
(For 20x8 inch tire)
Model No. 24515
(For 20x10 inch tire)
Model No. 24539
(For 23x9.5 inch tire)
REAR WHEEL WEIGHTS
Model No. 24003
(For 18x9.5 inch tires) (For 20x8 inch tires)
Model No. 24630
(For 23 inch tires)
GRASS BAGGER Model No. 24744 7 Bushel Capacity
(For 38”, 40”, and 42”)
Made in U.S.A.
52
Loading...