Models
22”
Front Drive
This Instruction Book contains information for several models.
Read and keep this book for future reference.
This book contains important information on
SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE.
PRODUCT INFORMATION
The owner must be certain that all
the product information is included with the unit.
This information includes
the INSTRUCTION BOOKS,
the REPLACEMENT PARTS and the WARRANTIES.
This information must be included to make sure state laws
and other laws are followed.
RECORD THE FOLLOWING INFORMATION ABOUT YOUR UNIT.
THIS INFORMATION IS NECESSARY WHEN ORDERING PARTS
OR IN CASE OF LOSS OR THEFT.
F–030406L
BUILT IN TH E
MURRAY, INC. Two Year Limited Warranty
Murray, Inc. warrants to the original purchaser that this unit shall be free from defects in material and workmanship under normal use and service for a period of Two (2) Years from
the date of purchase; however, this warranty does not cover engines, accessories (such as
snow blowers, snow blades, grass baggers and plows), transmissions, batteries and Normal Wear Parts (except as noted below) or transaxles as the companies that manufacture
these items furnish their own warranties and provide service through their authorized field
service facilities. For additional information, see the warranties covering these particular
parts. If you are uncertain whether your unit contains or is equipped with one or more of
these parts, consult your dealer prior to purchase. Subject to the terms and conditions noted
in this Limited Warranty, we shall, at our option, repair or replace at no cost to the original
purchaser any part covered by this Limited Warranty during the applicable warranty period.
In the event the battery proves defective within ninety (90) days from the date of purchase,
we will replace it without charge. If the battery proves defective after (90) days but within one
hundred twenty (120) days from the date of purchase, we will replace it for a charge of one
half (1/2) of the retail price of the battery in effect at the time of return.
Normal W ear Parts are defined as belts, blades, blade adapters, pneumatic tires, headlights
and seat covers. These parts are warranted to be free from defects in material and workmanship as delivered with the product. Any claim for repair or replacement of Normal W ear
Parts must be made within thirty (30) days of the date of purchase. No claims involving damage caused from material use, abuse or misuse will be honored.
This Murray, Inc. Two (2) Year Limited Warranty is your exclusive remedy; however, this
warranty is void or does not apply to any unit that has been tampered with, altered, misused,
abused or used for rental or other commercial and/or professional (non–homeowner) uses.
Your warranty does not cover minor mechanical adjustments which are not due to any defect in material or workmanship. For assistance in making such adjustments, consult your
Instruction Book.
To make a claim under this Murray, Inc. Two (2) Year Limited Warranty, return the unit (or
if authorized in advance, the defective part) along with your proof of purchase to an Authorized Service Center near you. To locate the nearest Authorized Service Center, call the
Central Parts Distributor for your area shown in the list provided with your unit or check the
Yellow Page listings in your local telephone directory. If you return the entire unit, we will
repair the unit. If we authorize the return of the defective part only, we will either replace or
repair the part. In the case of a defect in a transmission or differential (as distinguished from
a transaxle), the entire transmission or differential must be returned since they do not include user serviceable parts.
This Murray, Inc. Two (2) Year Limited Warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This Limited Warranty is given
in lieu of all other expressed and implied warranties including the implied warranty
of merchantability and warranty of fitness for a particular purpose. If you need addi-
tional information on this written warranty or assistance in obtaining service, call or write to
the address below. The model number along with the CUSTOMER CARE Center 1–800
number is on the Model Number Nameplate attached to the unit.
MURRAY, INC.
Outdoor Power Equipment
Customer Service Department
Brentwood, Tennessee 37027
P.O. Box 268
F–030406L
2
This instruction book is written for a person with some mechanical ability. Like most service books,
not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can
follow with some mechanical ability. Read and follow these instructions before you use the unit.
Know your product: If you understand the unit and how the unit operates, you will get the best
performance. As you read this manual, compare the illustrations to the unit. Learn the location and
the function of the controls. To help prevent an accident, follow the operating instructions and the
safety rules. Keep this manual for future reference.
IMPORTANT: Many units are not assembled and are sold in cartons. It is the responsibility of the
owner to make sure the assembly instructions in this manual are exactly followed. Other units are
purchased in an assembled condition. On assembled units, it is the responsibility of the owner to
make sure the unit is correctly assembled. The owner must carefully check the unit according to
the instructions in this manual before it is first used.
RESPONSIBILITY OF THE OWNER
The responsibility of the owner is to follow the instructions below.
1. Carefully read and follow the rules for safe operation.
2. Follow all the assembly and preparation instructions.
3. Inspect the unit.
4. Make sure that the operator of the unit knows how to correctly use all standard and accessory
equipment.
5. Operate the unit only with guards, shields, and other safety items in place and working correctly .
6. Correctly adjust the unit.
7. Service the unit only with authorized or approved replacement parts.
8. Complete all maintenance on the unit.
OWNER’S INFORMATION
F–030406L
Engine Exhaust, some of its constituents, and
certain vehicle components contain or emit
chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause
cancer and birth defects or other reproductive
harm. WASH HANDS AFTER HANDLING.
3
IMPORTANT
Safe Operation Practices for Walk–Behind Mowers.
This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.
I. General Operation
1. Read, understand, and follow all instructions on the machine and in the manual(s).
Be thoroughly familiar with the controls and
the proper use of the mower before starting.
2. Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
3. Only allow responsible individuals, who are
familiar with the instructions, to operate the
mower.
4. Thoroughly inspect the mower and area
where the equipment is to be used. Clear
the area of objects such as rocks, toys, wire,
bones, sticks etc., which could be picked up
and thrown by the blade.
5. Be sure the area is clear of other people before mowing. Stop mower if anyone enters
the area.
6. Do not operate the mower when barefoot or
wearing open sandals. Always wear substantial foot wear.
7. Do not pull mower backwards unless absolutely necessary. Look down and behind before and while moving backwards.
8. Do not operate the mower without proper
guards, plates, grass catcher or other safety
protective devices in place.
9. See manufacturer’s instructions for proper
operation and installation of accessories.
Only use accessories approved by the
manufacturer.
10. Stop the blade(s) when crossing gravel
drives, walks, or roads.
11. Stop the engine (motor) whenever you
leave the equipment, before cleaning the
mower or unclogging the chute.
12. Shut the engine (motor) off and wait until the
blade comes to complete stop before removing grass catcher.
13. Mow only in daylight or good artificial light.
14. Do not operate the mower while under the
influence of alcohol, drugs or other medica-
F–030406L
tion which can cause drowsiness or affect
your ability to operate this machine safely.
15. Never operate mower in wet grass. Always
be sure of your footing; keep a firm hold on
the handle and walk; never run.
16. Disengage the self–propelled mechanism
or drive clutch on mowers so equipped before starting the engine (motor).
17. If the equipment should start to vibrate abnormally, stop the engine (motor) and check
immediately for the cause. Vibration is generally a warning of trouble such as a blade
that is damaged, a loose blade, or the engine mounting bolts are loose.
18. Always wear safety goggles or safety
glasses with side shields when operating
mower to protect your eyes from foreign objects which can be thrown from the unit.
19. Plan your mowing pattern to avoid discharge of material toward roads, sidewalks,
bystanders and the like.
20. After striking a foreign object, stop the engine. Remove the wire from the spark plug.
Inspect the blade and mower for damage. If
damaged, repair before starting and operating the mower.
21. Keep any washout ports and other mower
housing service openings closed when
mowing.
II. Slope Operation
Slopes are a major factor related to slip and fall
accidents which can result in severe injury. All
slopes require extra caution. If you feel uneasy
on a slope, do not mow it.
DO:
Mow across the face of slopes; never up
and down. Do not mow excessively steep
slopes (maximum 15 degrees) or areas
where the ground is very rough. See the
“Guide” in the back of this manual to check
a slope. Exercise extreme caution when
changing direction on slopes.
Remove objects such as rocks, tree limbs,
etc.
Watch for holes, ruts, or bumps. Tall grass
can hide obstacles.
4
(Continued Following Page)
DO NOT:
IMPORTANT
Do not mow near drop–offs, ditches, or embankments. The operator could lose footing
or balance.
Do not mow excessively steep slopes.
Do not mow on wet grass. Reduced footing
could cause slipping.
III. Children
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are
often attracted to the mower and the mowing
activity. Never assume that children will remain
where you last saw them.
1. Keep children out of the mowing area and
under the watchful care of a responsible
adult.
2. Be alert and turn mower off if children enter
the area.
3. Before and while moving backwards, look
behind and down for small children.
4. Never allow children to operate the mower.
5. Use extra care when approaching blind corners, shrubs, trees, or other objects that
may obscure vision.
IV.Service
*1. Use extra care in handling gasoline and oth-
er fuels. They are flammable and vap or s a r e
explosive.
a. Use only an approved container.
b. Never remove gas cap or add fuel with
the engine running. Allow engine to cool
before refueling. Do not smoke.
c. Never refuel the machine indoors.
d. Never store the machine or fuel contain-
er inside where there is an open flame,
such as a water heater.
*2. Never run an engine indoors or inside a
closed area.
3. Never make adjustments or repairs to items
such as the height adjusters or grass catcher with the engine (motor) running. Discon-
nect the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting. Always wear eye protection when
you make adjustments or repairs.
4. Keep all nuts and bolts, especially blade attachment bolts, tight and keep equipment in
good condition.
5. Never tamper with safety devices. Check
their proper operation regularly.
6. To reduce fire hazard, keep mower free of
grass, leaves, or other debris build–up.
Clean up oil or fuel spillage. Allow mower to
cool before storing.
7. Stop and inspect the equipment if you strike
an object. Repair, if necessary, before restarting.
8. Never attempt to make wheel height adjustments while the engine (motor) is running.
9. Always disconnect electric mowers (live operated) before cleaning, repairing, or adjusting.
10. Grass catcher components are subject to
wear, damage, and deterioration, which
could expose moving parts or allow objects
to be thrown. Frequently check components
and replace with manufacturer’s recommended parts, when necessary. For storage, always make sure grass catcher is
empty.
11. Mower blades are sharp and can cut. Wrap
the blade(s) or wear gloves, and use extra
caution when servicing them.
12. Do not change the engine governor setting
or over–speed the engine.
13. Frequently check the blade for wear or damages such as cracks and nicks. A blade that
is bent or damaged must be immediately replaced with a factory replacement blade.
For safety and good cutting performance,
replace the blade every two years. Frequently check the blade bolt and the engine
mounting bolts. Replace damaged bolts
and tighten loose bolts.
14. Use only original equipment or authorized
replacement parts.
F–030406L
*Asterisked items do not apply to electric mowers.
5
Every person who uses power equipment
SAFE MOWING GUIDE
must learn the difference between proper and
improper use, safe and unsafe mowing practices. Read the next few pages carefully.
They can help you learn. Too often the mower user is inexperienced, not properly instructed, or has not read the Instruction Book
and instructions on the unit before using it for
the first time. This can result in unsafe use endangering the operator, bystanders, and the
equipment. Another result can be a poor appearance of the area mowed.
Read this Instruction Book. Read the instructions on the unit. Operate the mower according to the Safe Mowing Guide and other
safety rules and recommendations in this Instruction Book and on the unit. Make sure anyone who uses the unit has read the instructions
and has been told how to operate the mower
safely.
Your mower is designed to provide good service and durability in normal residential cutting. If the mower is not properly serviced and
maintained or used on unsuitable terrain or in
conditions not suitable for mowing, product
performance and safety will be reduced.
Proper attire is an important part of safe mowing. Safety glasses protect the eyes from
thrown objects. Safety shoes with steel toes
can protect a foot from being cut by the blade.
Shirts and pants that cover the arms and legs
can stop or deflect a thrown object.
gency. Learn how to cut and how to keep control of the mower at all times.
Many mowers are started manually. When using a pull start or rope start, place your feet
firmly and away from the blade. Hold the rope
handle securely, but never wrap the rope
around your arm or fingers for a “better grip”.
The mower is designed for use by one person.
Always mow alone. Never carry passengers.
Carrying a passenger is dangerous for the
passenger and the operator. A mower is not for
amusement or for carrying objects.
Is the area you are planning to mow wet? Never cut a wet lawn. Cutting wet grass can cause
an accident. It can affect mower performance
and also cause problems with future lawn
growth and appearance. Wet grass is slippery
and might cause the operator to fall or the
mower to slip. Someone could be hurt by
touching the blade. Wet grass tends to clog the
mower, causing poor discharge. Wet clippings
bunch up on the lawn retarding the growth of
grass. A wet mower can cause parts to rust
and reduce the useful life of the unit.
Practice using the mower before you actually
begin cutting grass. Select a large open level
area. Learn the location and function of the
controls and how they work. It is important that
the blade can be stopped quickly in an emer-
F–030406L
When you look over the lawn, refresh your
memory about hard, immovable obstacles
such as pipes, stumps, and rocks and avoid
them. They can cause damage to the mower
or an accident injuring the operator or a bystander. Take a litter bag along and walk over
the area to be cut. Pick up any stones, toys,
wire, bones, or other loose objects. These
items can damage the mower or they can become dangerous flying objects if the mower
blade hits them. The blade of a power mower
travels very fast. It can throw rocks and other
objects with force over long distances. Objects
thrown by mowers can break windows, cause
6
bruises, or even put out an eye. Often the per-
SAFE MOWING GUIDE
son hurt by a thrown object is a bystander such
as a child, another family member or a neighbor. Keep people and pets completely away
from the mowing area. Direct the mower’s discharge away from areas where people can be.
Planning your mowing pattern has a double
benefit. It can reduce chances of an injury and
make the clean up after mowing easier.
Are there ditches,
walls, or major inclines in the area to be
cut? Plan the mowing
pattern to avoid such
danger areas. Inclines and rough terrain must be mowed
carefully and some
areas must not be cut
with a mower at all.
With walk behind
equipment, mow
across the incline so
that if you or the mower slip, you won’t run
into each other.
Never mow slopes greater than 15 degrees.
See the “Guide” in the back of this Instruction
Book to check any slopes.
Ready to start cutting? Not yet. Be sure the
mower has been fully assembled according to
directions in the Instruction Book. Even if assembly was done by a lawn and garden shop
or the store where the unit was purchased, it
must be checked. Are all nuts, bolts and
screws tight? Does the engine have oil? These
items must be checked periodically throughout
the life of the mower.
Your mower has a gasoline engine. Gas is
dangerous. Store fuel only in a approved gas
container. Do not store large amounts of gas.
Put out all cigarettes, pipes and cigars before
working with gasoline. Store fuel and the mower itself in a well ventilated area away from any
possible source of ignition such a pilot light on
a furnace. If the mower is to b e stored for an extended time, remove the gas from the tank.
This minimizes the chance of a fire and keeps
the tank clear of deposits and old gasoline,
thus improving mower performance. Move the
mower outside before adding gasoline. Use a
funnel and wipe up any spilled fuel before starting. Remember, gasoline expands when
heated so leave some expansion room. Also,
most mower gas caps are vented to allow for
expansion. Always use the proper cap. People
are needlessly burned by fires, hurt in explosions, mowers and other property are damaged because of failure to follow basic safety
rules related to gasoline and fueling.
Never add gasoline to an engine that is running
or that is hot from recent use, this can cause an
accident. Remove dry grass and other debris
from the mower. Keeping the mower clean will
F–030406L
improve the performance, help the engine stay
cooler, extend the life of moving parts, and
minimize the danger of fire. People get burned
working with and around their mowers for other reasons than fire and explosions. It takes
only a few seconds of operation for the engine
and the muffler to become hot. Do not touch
these parts when the mower is running. Stop
the engine and let it cool down before servicing
the mower. Remember, exhaust fumes can be
dangerous. Never operate the engine indoors
or in an enclosed area.
Getting a new mower can be a big event for a
family. Let family members satisfy their curiosity about the mower and at the same time, tell
them about its dangers. Remember, a mower
is not a toy and is not for use by children or anyone lacking in age, strength or experience.
As with any power equipment, a mower can be
dangerous if not assembled, misused, or not
properly maintained. The most important rule
is to always use good judgement and common
sense.
Your mower will cut thick grass and heavy
plant stems with ease. Fingers and toes are no
more resistant to the mower’s blade. Many
people are injured because they “forgot” and
reached into the discharge chute. Always treat
your lawn mower as if the blade is rotating.
Never perform any service or try to make any
adjustment,except carburetor, while the engine is running.
Use only accessories suited for your mower.
Use of improper accessories can reduce the
safety designed into both the mower and the
accessory, it can even damage the unit. Read
and follow the instructions which come with the
accessory and the mower.
7
Use only original equipment or approved sub-
SAFE MOWING GUIDE
stitutions as service parts. If you need professional service, select a shop that is an
Authorized Service Center for your brand of
mower. If you plan to service the unit yourself,
follow directions in the Instruction Book.
in the rain is no fun and it is dangerous. Always
seek shelter in an electrical storm. In extremely dry mowing conditions, your safety glasses
can serve a dual purpose by protecting your
eyes from dust and thrown objects, also a dust
or pollen mask can be helpful.
As you mow, remember children and pets are
sometimes attracted to the activity. Be especially careful when trimming around shrubbery
or when backing up. If at all possible, don’t
mow when moving backwards. It is dangerous
because vision is restricted. Also, blades are
designed to cut while the unit is moving forward so cutting performance is reduced when
mowing in reverse.
Never leave the mower running and unattended. Shut off the engine. Put the mower in
a position so that it can not roll. If the unit is
self–propelled, make sure the drive control is
disengaged.
When mowing, be aware of your condition and
the weather conditions. After mowing a long
time, you will be tired. This is the time when
reactions slow down, your attention wanders;
the time when you are wide open for an accident. Take a short break. If temperatures are
high, take precautions to avoid becoming dehydrated. If you are angry, tired, or unable to
give your full attention to mowing, if you have
been consuming alcohol, medicines, or drugs,
do not use your mower or any type of power
equipment.
If weather conditions become worse while you
are cutting, stop and finish later. Cutting grass
F–030406L
Your mower is equipped with a number of safety features which are important to the safety of
the operator and bystanders and must never
be altered or removed. If a safety feature becomes inoperable, lost, or damaged, it must be
repaired or replaced before the mower is used.
Engine speed is a key to safe mowing and a
nice looking lawn. The maximum speed of the
engine on your mower has been set at the factory. Do not change the engine governor in any
way.
Select the maximum engine and ground speed
that is right for the terrain and the height of
grass. You get the best cutting and bagging
performance when using a grass catcher by
operating the engine at maximum speed. Never walk fast or run just to get the job done sooner. On inclines, reduce ground speed and
exercise extreme care.
It is best to mow only during daylight hours;
however, if you must mow in the late afternoon
or evening, make sure there is good artificial
light.
Your mower will require maintenance including
service and adjustments before and after use
as with any machine. The frequency of the
maintenance is generally based on hours of
use, however, the frequency can vary because
of mowing conditions. Check the Instruction
Book for more detailed instructions. Proper
maintenance protects your investment in the
mower and helps insure that it will function
safely and reliably.
Never attempt any
service (with the possible exception of carburetor adjustment)
with the engine running. After turning the
engine off, always
disconnect the spark
plug wire to prevent
accidental restarting
while the unit is being
serviced.
8
While mowing, if you hit a foreign object, stop
SAFE MOWING GUIDE
the engine. Remove the spark plug wire. Carefully and thoroughly inspect the mower for
damage. Make necessary repairs before restarting. If the unit starts to vibrate abnormally,
stop the engine immediately and check for the
cause. Vibration is generally a warning of
trouble. Keep all nuts, bolts, and screws tight.
The blade is the most dangerous part of the
mower and also the most important part in obtaining a nice lawn appearance. Check the
blade and the blade mounting hardware frequently. Keep it tight. If the blade hits a solid
object, check it thoroughly for deformation or
cracks and replace if damaged. For safety,replace the blade every two years. A sharp blade
reduces the work load on the engine and cuts
grass more cleanly, for a better looking cut with
less work. The blade is always close to the outside of the mower housing. For best trimming
on side discharge mowers, cut with the left
side of the housing toward the area that needs
trimming.
A useful accessory for your mower is a grass
catcher. There are grass catchers available for
most models. For best performance and safety, be sure the grass catcher is approved for
use with your mower. Assemble as directed
and follow operating and safety instructions
with the catcher and in the Instruction Book.
Before mounting, checking or emptying the
grass catcher, always turn the engine off. Remember to check the grass catcher before
each use for cracks, wear, or deterioration. Replace any part that is damaged with the manufacturer’s recommended replacement part
before using the grass catcher again.
Proper cutting technique is important if you
want your lawn to look good. Avoid the temptation to cut grass too short. Cutting grass too
short can kill the plant, cause grass to turn yellow, or make the lawn look brown and thatchy.
Use the lower cutting heights in cool months
when the grass is lush. Use the higher cutting
heights in extremely dry periods. Cutting with
a dull blade or low engine speed bruises,
shreds, and can uproot some grass making
the lawn look dull and brown a few days after
cutting. Always put the throttle control in FAST
F–030406L
position when mowing and bagging. When
bagging, slower ground speed will provide the
best results.
Change the mowing pattern slightly each time
you cut. If you always cut the same way, the
grass will develop a “set” and clippings will accumulate more heavily in some areas more
than in others causing grass to get thinner in
those areas. Do not service your mower over
the grass. Spilled oil and gas can kill the grass.
In tall grass or very heavy grass, do not try to
cut it all at once. Raise the height of cut on the
first cutting and lower it for the next cutting the
same day or within a few days. Another way is
to cut only part of the width of the mower and
adjust your ground speed (not the engine) to
move more slowly so the mower can clear itself as it moves forward.
When cutting with a walk behind mower, always push the unit. Do not pull it. Pushing the
unit keeps the operator behind the mower in
the “operator’s zone” for better control. Pushing the unit also gives you a chance to see exactly where and what you are mowing. There
will be times while you are mowing that you will
have to pull the mower backwards (such as
when the front of the mower has come up
against a wall or fence). If you must back up,
make sure your feet are in the clear. Stand well
back from the mower, plant your feet firmly with
each step and back up being careful to look behind you. Resume normal mowing as soon as
possible.
If your unit is self–propelled, remember that
the drive mechanism is not designed to do all
the work, but the unit can move without your
help. Always keep your hands on the handle
near the controls when the engine is running.
Remember too that the self–propelled mechanism can be dangerous. Keep hands and feet
away from belts and chains. Always turn off the
engine before attempting to remove anything
that becomes entangled in the self–propelled
system.
Remember, your mower is a useful tool, but it
can be dangerous. Follow the instructions in
this Instruction Book. Use the mower properly
and carefully and it will give you many hours of
trouble free, accident free operations.
9
STEPS TO FOLLOW
BEFORE MOWING
D Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes.
D Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory
replacement blade.
D Fill the fuel tank outside. Clean off spilled fuel.
D Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with
any attachments. Owner’s Manual instructions are for your safety and the safety of others.
D Exhaust fumes are dangerous. Start the engine outside.
D Make sure all safety devices are in place and working correctly.
D Operation of the mower is only for a person that has experience.
D Wet grass can be dangerous. Let the grass dry.
D Instruct children and others to keep away from the work area.
D Never cut the grass without good light.
D Pick up loose objects. Remove them from the mowing area.
WHILE MOWING
D Watch for fixed objects and avoid them. They can damage the mower or cause injury.
D A hot engine and muffler will cause a burn. Do not touch.
D Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check
a slope.
D Lack of daylight or good artificial light is cause to stop mowing.
D Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the
unit vibrates excessively.
D Do not make adjustments or repairs without stopping the engine (except for carburetor). Dis-
connect the spark plug wire.
D On or near roads, watch out for traffic. Direct discharge away from roads.
D When mowing, avoid areas where traction is unsure. Before and while moving backwards, look
behind and down for small children.
D In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass
from the mower.
D Never remove any safety related parts.
D Do not pour gasoline into a engine that is hot or running.
AFTER MOWING
D Always let the mower cool before storing in an enclosed area.
D Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before
storing.
D Tighten all loose nuts, bolts and screws before you use the unit.
D Empty and clean any grass catcher or other accessory.
D Remove the key or disconnect the spark plug wire to prevent unauthorized use.
D Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion.
D Only original parts or factory approved substitutes can be used to service the mower.
D When storing the mower for an extended period, remove the fuel from the fuel tank.
D Instruct children to leave the mower alone. It is not a toy.
D Never keep gasoline near a source of ignition. Always use an approved container. Keep
gasoline away from children.
D Lubricate according to the Instruction Book. See “Lubrication”.
IMPORTANT––Read the Instruction Book. Keep this book for future use and
reference.
WARNING: Look for this symbol to point out important
safety precautions. It means: “Attention! Become
Alert! Your Safety Is Involved.”
F–030406L
10
PREPARATION
UNPACKING INSTRUCTIONS
The mower was fully assembled at the factory.
When the mower was put in the carton, the
handle was put in the storage position. To put
the handle in the operating position, follow the
steps below.
Handle
1. Remove the mower from the carton.
2. Put the lower handle in the operating position. Make sure the lower handle is between the locking tabs (Figure 1).
Locking
Handle
Bracket
Upper Handle
Wingnut
Lower Handle
Tabs
Wingnut
Figure 1
3. Put the upper handle in the operating
position. Tighten the wingnuts.
CAUTION: Be careful when you fold or
raise the handle. Do not damage the
cables. A cable that is bent will not work
correctly. Before you use the unit, replace a bent or damaged cable.
4. To attach the recoil–start grip to the rope
guide, twist the rope through the rope
guide mounted on the right side of the han-
dle (Figure 2).
NOTE: If you cannot attach the
recoil–start grip because the rope is too
short, hold the engine stop lever
against the handle. Slowly pull the
recoil–start grip.
Rear Wheels (Hi–Wheel Models With
Axle Knobs)
1. Remove the washers and axle knobs
from the axle bolts (Figure 3).
2. Mount the rear wheels onto the axle bolts
and fasten with the washers and axle
knobs.
Recoil–Start
Grip
Rope
Guide
Rear Wheel
Figure 2
Axle Knob
Washer
Axle Bolt
Figure 3
F–030406L
11
PREPARATION
HOW TO ADJUST THE HANDLE HEIGHT
The handle bracket has two assembly positions. A HIGH and a LOW position (Figure 4).
The HIGH position will raise the handle ap-
proximately four inches.
Lower Handle
Handle Bracket
HIGH
1. Remove the wingnuts and bolts from the
right and left handle brackets (Figure 5).
2. To raise the handle, mount the lower han-
dle in the HIGH position shown in Figure 6.
3. To lower the handle, mount the lower han-
dle in the LOW position shown in Figure 7.
LOW
Figure 4
Wingnut
Figure 5
HIGH Position
Handle
Bracket
Figure 6
LOW Position
4. Attach the lower handle to the handle
brackets with the bolts and wingnuts.
(Figure 5).
F–030406L
12
Handle
Bracket
Figure 7
PREPARATION
HOW TO PREPARE THE ENGINE
ENGINE DOES NOT CONTAIN
See the engine manufacturer’s instructions for
the type of gasoline and oil to use. Before you
use the unit, read the information on safety, o p eration, maintenance, and storage.
IMPORTANT: This unit is equipped with an
internal combustion engine and must not
be used on or near any unimproved forest–
covered, brush–covered or grass–covered
land unless the engine’s exhaust system is
equipped with a spark arrester meeting
applicable local or state laws (if any). If a
spark arrester is used, it must be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states
may have similar laws. Federal laws apply
on federal lands. See an Authorized Service Center for a spark arrester for the
muffler.
OIL OR GASOLINE
WARNING: Follow the engine
manufacturer’s instructions for
the type of gasoline and oil to
use. Always use a safety gasoline container. Do not smoke
when adding gasoline to the engine. When inside an enclosure,
do not fill with gasoline. Before
you add gasoline, stop the
engine. Let the engine cool for
several minutes.
ENGINE TIPPING
When you service the engine, inspect the
blade, or clean the underside of the mower
housing; make sure to always tip the engine
with the spark plug up (see Figure 8). Transporting or tipping the engine with the spark
plug down will cause:
S Hard starting.
S Engine smoking.
S Spark plug fouling.
S Oil or gas saturation of the air filter.
Figure 8
IMPORTANT: Actual sustained horsepower will likely be lower due to operating limitations and environmental factory.
FINAL ASSEMBLY
Before you use the mower, check the assembly of the wheels, the handle, and the controls.
Make sure all the fasteners are tight. Make
sure the throttle control and the engine stop lever work correctly.
F–030406L
13
PREPARATION
MODELS WITH OPTIONAL MULCHER PLATE
MULCHER PLATE
REMOVAL AND INSTALLATION
WARNING: Before you remove
or install the mulcher kit, disconnect the wire to the spark plug.
On some models the mulcher kit is installed at
the factory. To convert from a mulcher to a side
discharge, remove the mulcher plate.
A side discharge mower can be converted to a
mulching mower by installing the mulcher
plate as follows:
1. Raise the chute deflector (Figure 9).
Chute
Deflector
Bump
Tab
Mulcher Plate
Figure 9
2. Align the mulcher plate with the side discharge opening. Make sure that the two
alignment bumps are inside of the opening.
3. Mount the tab on the top of the mulcher
plate to the inside of the mower housing.
4. Mount the tab on the bottom of the mul-
cher plate to the inside of the mower
housing (Figure 10).
5. Lower the chute deflector.
Bump
Tab
Mulcher Plate
Chute
Deflector
Figure 10
MULCHING TIPS
Mulching finely cuts the grass so that the grass
can be easily recycled. Because the nutrients
are returned to the soil, the lawn will need less
fertilizer. To correctly mulch the lawn, follow
the tips below.
S The grass must be dry . If the grass is wet,
it will be difficult to cut and cause heavy
clumps of grass.
S The grass must not be too tall. The maxi-
mum height to effectively cut is 4 1/2 inches. Set the height adjusters so that only
the top third of the grass is cut.
S If the grass is more than 4 1/2 inches high,
two mowings will be necessary. For the first
mowing, set the height adjusters in the
highest position. Then, lower the height adjusters for the second mowing.
F–030406L
S Keep a sharp edge on the blade. A blade
that is not sharp will cause the ends of the
grass to become brown.
S Clean the underside of the mower housing.
Grass and other debris can keep the mower from working correctly.
If the quality of cut is marginal, try the
following:
S Set the height adjusters at a higher cutting
height.
S Cut the grass more frequently.
S Operate the mower at a slower ground
speed.
S Overlap the cutting swaths instead of cut-
ting a full swath with each pass.
S Mow across the marginal areas a second
time.
14
OPERATION
ENGINE STOP LEVER
Release the engine stop lever and the engine
and the blade will automatically stop. To run
the engine, hold the engine stop lever in the
Operating position (Figure 12).
Before you start the engine, operate the en-
gine stop lever several times. Make sure the
cable moves easily.
WARNING: For safe operation,
the drive system must immediately disengage when the drive
lever is released. If the drive
system does not disengage
correctly, do not operate the
mower until the drive system is
adjusted or repaired by an
authorized service center.
Operating Position
Engine Stop
Lever
Figure 11
FRONT WHEEL DRIVE SYSTEM
The mower has a front wheel drive system.
Operate the drive system as follows.
1. Hold the engine stop lever in the Operat-
ing Position (Figure 11 and Figure 12).
2. Push the drive lever completely forward.
When the drive lever clicks, release the
drive lever. The drive system is now engaged.
NOTE: To stop the engine, release the
engine stop lever.
3. To disengage the drive system and stop
the engine, completely release the engine
stop lever.
4. To disengage only the drive system, release the engine stop lever approximately two inches. The drive system will
disengage but the engine will continue to
run.
NOTE: When the drive system is
disengaged on a new unit, it is possible for
the front wheels to rotate if lifted off the
ground. This is normal with a new belt and
will stop after one or two hours of
operation.
F–030406L
Drive Lever
Hold the engine stop lever
in the Operating position.
To go forward, move the
drive lever forward.
Figure 12
HOW TO STOP THE ENGINE
To stop the engine, release the engine stop
lever. Disconnect the wire from the spark plug
to prevent the engine from starting. On models
equipped with an electric start engine, remove
the key from the key switch. Keep the key
away from children.
If the engine will not stop, hold a screwdriver
against the spark plug and against the engine
cooling fins. The spark will go to ground and
the engine will stop. Before you start the engine, check the engine stop cable. Make sure
the engine stop cable is assembled correctly.
Before you operate the unit, replace a bent or
damaged engine stop cable.
15
OPERATION
HOW TO START ENGINE
WARNING: The blade will rotate
when the engine runs.
IMPORTANT: Before you start the engine,
operate the engine stop lever several
times. Make sure the engine stop cable
moves freely.
NOTE: The engine design does not include
a throttle control or an engine speed adjustment. The engine is set at the best
speed for cutting grass, bagging grass,
and for extended engine life.
1. Check the oil.
2. Fill the fuel tank with regular unleaded gasoline. Make sure the gasoline is clean.
Leaded gasoline will increase deposits an d
shorten the life of the valves.
NOTE: Do not use gasohol or methanol. Do
not use premium unleaded gasoline.
WARNING: Always use a safety
gasoline container. Do not smoke
when adding gasoline to the fuel
tank. When inside an enclosure,
do not add gasoline. Before you
add gasoline, stop the engine and
let the engine cool for several
minutes.
3. Make sure the spark plug wire is connected
to the spark plug.
4. Electric Start Models: Make sure the battery is connected to the wiring harness.
5. Make sure the drive lever is in the DISENGAGED position (Figure 13).
Hold the engine stop lever
in the operating position.
WARNING: To prevent an accident, make sure the drive lever is
in the DISENGAGED position.
When the drive lever is in the ENGAGED position, do not start the
engine.
6. Some models have a primer button on the
front or side of the engine (Figure 14). Every time you push the primer button, wait
two seconds. For the number of times required to push the primer button, see the
engine manufacturer’s instructions.
Primer Button
Figure 14
NOTE: Do not use the primer button to
start a warm engine.
7. Stand behind the mower. Hold the engine
stop lever in the OPERATING position
(Figure 13).
8. Electric Start Models: Turn the ignition
key to the START position. Use short starting cycles (15 seconds per minute). When
the engine starts, release the ignition key.
If the engine will not turn over, charge the
battery. See “How To Charge The Battery”.
9. Recoil–Start Models: Rapidly pull the re-
coil–start grip. Slowly return the recoil–
start grip.
10. If the engine does not start in 5 or 6 tries,
See the “Problem and Repair” Instructions.
Drive Lever
F–030406L
Ignition Key
Figure 13
HOW TO OPERATE THE MOWER
WARNING: Check the condition
of the grass bag for wear or deterioration. If worn or damaged, replace the parts only with approved factory replacement
parts. For replacement parts,
see the parts list in this book.
To completely fill the grass bag, operate the
engine with the throttle control in the FAST
position.
16
MAINTENANCE
ENGINE MAINTENANCE
Use the following maintenance section to keep
your unit in good operating condition. All the
maintenance information for the engine is in
the “Engine Instruction Book”. Before you start
the engine, read this book.
WARNING: Before you make an
inspection, adjustment (except
carburetor), or repair, stop the
engine and disconnect the wire
from the spark plug.
ENGINE TIPPING
When you service the engine, inspect the
blade, or clean the underside of the mower
housing; make sure to always tip the engine
with the spark plug up (see Figure 15). Transporting or tipping the engine with the spark
plug down will cause:
S Hard starting.
S Engine smoking.
S Spark plug fouling.
S Oil or gas saturation of the air filter.
Figure 15
HOW TO CLEAN
THE MOWER HOUSING
WARNING: The blade will rotate
when the engine runs. Before
you clean the mower housing,
stop the engine and disconnect
the wire from the spark plug.
Grass and other debris can keep the mower
from working correctly. After you mow, clean
the mower housing as follows.
1. Stop the engine.
2. Disconnect the wire from the spark plug.
3. Clean the top and the bottom of the mower
housing.
LUBRICATION
1. For maximum performance, lubricate the
wheels and all pivot points with engine oil
every 25 hours.
2. To lubricate the engine, refer to the “Engine Instruction Book”.
NOTE: Do not lubricate the engine stop
cable. Lubricants will damage the cable
and prevent the cable from moving freely.
Replace the cable if bent or damaged.
F–030406L
HOW TO ADJUST
THE HEIGHT OF CUT
WARNING: The blade will rotate
when the engine runs. Before
you change the height of cut,
stop the engine and disconnect
the wire from the spark plug.
T o change the height of cut, move the position
of the adjuster arm at each wheel (Figure 16).
Make sure each adjuster arm is in the same
position so that the mower will cut level.
1. Disengage the adjuster arm.
2. Move the adjuster arm to another position.
Adjuster
Figure 16
17
Arm
MAINTENANCE
HOW TO REMOVE THE DRIVE BELT
WARNING: Before you remove
the belt, disconnect the wire
from the spark plug.
1. Loosen, DO NO REMOVE, the bolt for the
debris shield (Figure 17).
2. Remove the screw and the debris shield
(Figure 18).
3. Remove the belt cover (Figure 19).
4. Remove the front wheels.
5. Remove the retainer ring and the spring
pin (Figure 20).
6. Remove the dust cover and pinion gear.
7. Remove the hair pin from the axle.
8. Slide the axle as shown until the drive belt
can be removed from the drive pulley.
9. Remove the drive belt.
NOTE: Make sure you replace the drive
belt only with a replacement belt from
the factory.
10. To assemble the drive belt, reverse the
above steps.
11. Before you begin to mow, make sure the
drive system will correctly disengage and
that the mower will stop. If the drive system
will not disengage, take the mower to an
authorized service center before you operate the mower.
Belt Cover
F–030406L
Screw
Debris Shield
Bolt
Figure 17
Figure 18
18
Screw
Hair Pin
Axle
Drive Pulley
Thrust Washer
Washer
Front Wheel
Belt
Pinion Gear
Dust Cover
Pinion Gear
Washer
Spring Pin
Hub Cap
Nut
Figure 19
Engine
Pulley
Retainer
Ring
Figure 20
MAINTENANCE
BLADE SERVICE
WARNING: Before you inspect
the blade or the blade adapter,
disconnect the wire to the spark
plug. If the blade hits an object,
stop the engine. Disconnect the
wire to the spark plug. Check the
unit for damage.
Frequently check the blade for wear or damage such as cracks. Frequently check the bolt
that holds the blade. Keep the bolt tight. If the
blade hits an object, stop the engine. Disconnect the wire to the spark plug. Check the
blade adapter for damage. Check for a bent or
damaged blade, a badly worn blade, or other
damage. Before you operate the unit, damaged parts must be replaced with factory replacement parts. For safety, replace the blade
every two years. Keep a sharp edge on the
blade. A blade that is not sharp will cause the
ends of the grass to become brown. Remove
the blade as follows.
HOW TO REMOVE THE BLADE
WARNING: Before you remove
the blade, disconnect the wire to
the spark plug. The blade has
sharp edges. When you hold the
blade, use gloves or cloth materi-
1. Drain the fuel tank.
2. Lift the side of the mower that has the
3. Use a piece of wood to keep the blade
4. Remove the bolt that holds the blade.
al to protect your hands.
muffler or spark plug.
from rotating.
5. Check the blade according to the ”Blade
Service” instructions. Replace a badly
worn or damaged blade with a factory replacement blade.
6. Mount the blade with the curved edges toward the housing. If the blade is upside
down, the blade will not cut correctly and
can cause an accident.
7. Fasten the blade with the original wash-
ers and bolt. Make sure the outside rims
of the Belleville washers are toward the
blade (Figure 21).
8. Tighten the bolt that holds the blade to a
torque of 30 foot pounds.
WARNING: Always keep the bolt
that holds the blade tight. A loose
bolt or blade can cause an accident.
HOW TO SHARPEN THE BLADE
WARNING: V ibration is the result
if the blade is not correctly balanced. A blade that is damaged
with cracks can break and cause
an accident.
1. Sharpen the blade two times a year or every 25 hours.
2. If the blade is on the unit, do not sharpen.
Remove the blade according to the instructions in ”How To Remove The Blade”.
3. Clean the blade with a brush, soap, and
water. Check the blade. Look for cracks,
nicks, or other damage. Replace a blade
that is badly worn, bent, or damaged with
a factory replacement blade.
4. Sharpen the blade with a file. Make sure
you keep the original beveled cutting edge
(Figure 22).
(Continued following page)
Blade Adapter
Blade Adapter
F–030406L
Belleville
Bolt
Belleville Washer
Flat Washer
Bolt
Blade
Washer
Washer
Mulching
Blade
Figure 21
19
Screwdriver
Ground
Blade
File
Blade is balanced
when parallel to
the ground.
Figure 22
5. Make sure the blade is balanced. Use a
MAINTENANCE
screwdriver and hold the blade parallel to
the ground as shown. A blade that is balanced will stay parallel to the ground. If the
blade is not balanced, the heavy end will
rotate toward the ground. Sharpen the
heavy end until the blade is balanced.
6. A new blade will cut better than a badly
worn blade. Every two years replace the
old blade with a factory replacement
blade.
CHECK THE LEVEL OF CUT
T est the unit in a small area. If the height of cut
is not level or if the cut grass is not discharged,
the cause can be: (1) the blade is bent or damaged, (2) the blade is not sharp, (3) a worn
blade, (4) or a broken blade adapter. Before
you use the unit, correct the problem.
Push in on
lower handle.
Figure 23
FOLDING HANDLE STORAGE
CAUTION: Be careful when you fold or
raise the handle. Do not damage the
cables. A cable that is bent will not work
correctly. Before you use the unit, replace a
bent or damaged cable.
How To Fold The Handle
1. Loosen the knobs that hold the upper part
of the handle to the lower part of the handle. As you fold the handle, make sure the
cables are not around the loose fasteners
and do not become damaged. Rotate the
upper part of the handle toward the back
of the unit (Figure 23) .
2. Loosen the knobs on the lower handle
(Figure 24). Push in on the ends of the
lower handle. Move the ends of the lower
handle past the locking tabs.
3. Rotate the handle forward over the engine. Make sure the cables are not damaged.
HOW TO PREPARE THE MOWER
FOR STORAGE
WARNING: Do not remove gasoline while inside a building, near
a fire, or while you smoke.
Gasoline fumes can cause an
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Drain the oil from the warm engine. Fill the
F–030406L
explosion or a fire.
engine crankcase with new oil.
Lower Handle
Locking
Tabs
Knob
Figure 24
How To Raise The Handle
1. Pull the handle back until the ends of the
lower handle lock into position.
2. Lift the upper part of the handle into the operator’s position. Tighten the fasteners
that hold the handle.
4. Remove the spark plug from the cylinder.
Pour one ounce of oil into the cylinder.
Slowly pull the recoil–start grip so that the
oil will protect the cylinder. Install a new
spark plug in the cylinder.
5. Clean the dirt and debris from the cylinder
cooling fins and the engine housing.
6. Clean the bottom of the mower housing.
7. Completely clean the mower to protect the
paint.
8. Put the unit in a building that has good ventilation.
20
TROUBLE SHOOTING CHART
The Engine will not start.
1. Make sure the fuel tank is filled with clean gasoline. Do not use old gasoline.
2. On a cold engine, push the primer button (optional on some models). For the number of times
required to push the primer button, see the engine manufacturer’s instructions.
3. Make sure the wire for the spark plug is connected to the spark plug.
4. Adjust the Carburetor. See the “Engine Instruction Book”.
5. There is too much gasoline in the engine cylinder. Remove and dry the spark plug. Put the
throttle control in the SLOW position. Pull the recoil–start grip several times. Install the spark
plug. Connect the wire to the spark plug. Start the engine.
6. The engine is difficult to start in heavy or high grass. Move the mower to a clean dry surface.
7. Make sure the engine stop lever is in the operating position.
8. Make sure the fuel valve is in the ON position. See the “Engine Instruction Book”.
9. On Electric Start models, charge the battery.
The Engine will not stop.
1. Release the engine stop lever.
2. Check the engine stop cable. Replace the cable if bent or damaged.
The Engine performance is bad.
1. Check the height of cut settings. Raise the height of cut if the grass is high.
2. Check the bottom of the blade housing. Clean the blade housing of grass and other debris.
3. Check the wire to the spark plug. Make sure the wire is connected.
4. Clean the engine cooling fins of grass and other debris.
5. Check the carburetor adjustments. See the “Engine Instruction Book”.
6. Check the spark plug gap. Set the spark plug gap at 0.030”.
7. Check the amount of oil in the engine. Fill with oil if necessary.
8. Check the engine air cleaner. See the “Engine Instruction Book”.
9. The gasoline is bad. Drain and clean the fuel tank. Fill the fuel tank with clean gasoline.
Excessive Vibration.
1. Remove the blade. Check the blade and balance if necessary. See the blade maintenance
instructions.
2. Check for a bent or broken blade. A DAMAGED BLADE IS DANGEROUS AND MUST BE
REPLACED.
3. Check the blade adapter. REPLACE A BROKEN BLADE ADAPTER.
4. If the vibration continues, take the mower to an Authorized Service Center.
The grass will not discharge correctly.
1. Clean the bottom of the mower housing.
2. Check for a badly worn blade. Remove and sharpen the blade. For safety, replace the blade
every two years with a factory replacement blade.
The grass is not cut even.
1. Check the height adjustment at each wheel. The height adjustment must be the same for each
wheel.
2. Make sure the blade is sharp.
3. Check for a bent or broken blade. A DAMAGED BLADE IS DANGEROUS AND MUST BE
REPLACED.
4. Check for a broken blade adapter. REPLACE A BROKEN BLADE ADAPTER.
F–030406L
21
HANDLE – RECOIL–START MODELS
1
4
8
3
9
6
16
5
5
2
KEY
NO. DESCRIPTION PART NO.
1 Handle, Upper (Black)
Handle, Upper (Gray)
2 Handle, Lower (Black)
Handle, Lower (Gray)
1101556E701
1101556E724
71137E701
71137E724
3 Bolt 25x14
4 Control, Drive 672877
5 Locknut 15x116
6 Cable, Stop *
Cable, Stop #
Cable, Stop +
1101182
672835
672841
12
13
11
11
KEY
NO. DESCRIPTION PART NO.
8 Lever, Stop 672879E701
9 Bracket, Stop Lever 1101454
11 Fastener, Cable 1101353
12 Bolt 2x77
13 Knob 71294
16 Guide, Rope 71530
* Used on Briggs & Stratton Quantium engines.
# Used on Tecumseh engines.
+ Used on Briggs & Stratton Classic, Sprint & Quattro
F–030406L
22
, Q–Style and QS–Style engines.
HANDLE – ELECTRIC–START MODELS
28
1
4
8
5
5
5
6
16
10
27
17
3
26
13
18
20
19
22
21
23
11
12
24
2
KEY
NO. DESCRIPTION PART NO.
1 Handle, Upper (Black)
Handle, Upper (Gray)
2 Handle, Lower (Black)
Handle, Lower (Gray)
1101556E701
1101556E724
672572E701
672572E724
3 Bolt 25x14
4 Control, Drive 672877
5 Locknut 15x116
6 Cable, Stop *
Cable, Stop #
Cable, Stop +
1101182
672835
672841
8 Lever, Stop 672879E701
9 Fastener, Cable 1101353
10 Screw 26x220
11 Tie, Cable 71372
12 Bolt 2x77
25
9
11
KEY
NO. DESCRIPTION PART NO.
13 Knob 71294
16 Guide, Rope 71530
17 Cap 91488
18 Nut 91489
19 Bolt 3x136
20 Cover, Ignition 671916
21 Switch Ignition & Key 776011
22 Charger, Battery 671992
23 Harness, Wiring 776012
24 Battery 776014
25 Case, Battery 776013
26 Bracket, Battery 671959
27 Key, Ignition 672220
28 Bracket, Stop Lever 1101454
* Used on Briggs & Stratton Quantium engines.
# Used on Tecumseh engines..
+ Used on Briggs & Stratton Classic, Sprint & Quattro
F–030406L
23
, Q–Style and QS–Style engines.
MODELS WITH STANDARD WHEELS
21
10
58
18
53
25
22
19
46
10
23
54
47
20
49
24
16
22
14
29
36
9
17
33
39
44
41
36
40
36
48
53
47
6
52
52
11
31
45
30
46
47
55
6
26
1
27
5
3
28
68
51
64
32
7
69
34
43
65
39
38
42
50
57
4
37
35
2
15
12
13
F–030406L
25
56
24
MODELS WITH STANDARD WHEELS
KEY
NO. DESCRIPTION PART NO.
1 Engine * -----2 Housing 776023
3 Height Adjuster, Left Rear 672641
4 Knob 71495
5 Wheel and Tire, Rear # ----6 Locknut, Flange 15x84
7 Bolt, Carriage 2x81
9 Bolt, Engine 25x11
10 Nut 15x68
11 Height Adjuster, Left Front 672643
12 Washer, Belleville 17x137
13 Washer 17x124
14 Bolt, Hex 1x153
15 Blade, Side Discharge 42225E701
Blade, Mulcher 1101120E701
16 Adapter, Blade 672503
17 Height, Adjuster, Right Frt. 672642
18 Height, Adjuster, Right Rr. 672640
19 Guard, Rear 672738
20 Screw 26x245
21 Deflector, Chute 672421
22 Push-On Cap 28x42
23 Pin, Pivot 215x11 Z
24 Spring 166x5
25 Baffle 672744E701
26 Wheel and Tire, Drive # ----27 Pulley 71434
28 Pin, Spring 32x64
29 Base, Engine 672671
30 Cover, Belt (Black) 1101025
31 Screw 26x259
32 Bracket, Idler Support 1101240 Z
33 Washer 17x45
34 Screw 26x263
* Parts are available from an Authorized Engine Service Center. See Engines, Gasoline" or Gasoline
Engines" in the yellow pages of the telephone directory.
# See the Wheel And Tire Parts List" page.
KEY
NO. DESCRIPTION PART NO.
35 Idler, Backside 71778
36 Locknut 15x43
37 Bearing 71793
38 Spring 166x45
39 Spacer 71789
40 Arm, Pivot 1101121 Z
41 Spacer 71788
42 Pulley, Idler 71779
43 Bolt, Shoulder 9x50
44 Belt, Briggs & Stratton
Belt, Tecumseh
45 Washer 17x186
46 Ring, Retainer 11x16
47 Gear, Pinion 71792
48 Pulley 71791
49 Pin, Drive 43629
50 Pin, Hair 31x9
51 Axle 672508
52 Washer 17x169
53 Cover, Dust 71780
54 Bolt 1x85
55 Hub Cap 43615
56 Plate, Mulch - Optional 672422 Z
57 Bracket, Left Handle 1101303E700
58 Bracket, Right Handle 1101302E700
59 Screw 26x289
60 Bolt 1x120
62 Washer 17x45
64 Screw 26x288
65 Shield, Debris 1101026E701
68 Bolt, Carriage 2x86
69 Bolt 1x81
- Book, Instruction F-030406L
37x100
37x101
F–030406L
25
MODELS WITH 14” REAR WHEELS
21
18
10
61
62
22
19
23
20
24
22
36
33
37
10
4
59
1
28
27
29
35
64
68
32
30
31
41
44
36
40
36
45
58
57
6
46
5
3
7
69
34
39
38
39
42
43
7
F–030406L
60
10
56
25
53
46
10
54
25
47
16
49
14
17
9
48
52
49
50
52
53
26
12
13
15
51
2
65
66
47
11
55
6
26
MODELS WITH 14” REAR WHEELS
KEY
NO. DESCRIPTION PART NO.
1 Engine * -----2 Housing 776043
3 Height Adjuster, Left Rear 672645
4 Knob 71495
5 Wheel and Tire, Rear # ----6 Locknut, Flange 15x84
7 Bolt, Carriage 2x81
9 Bolt, Engine 25x11
10 Nut 15x68
11 Height Adjuster, Left Front 672643
12 Washer, Belleville 17x137
13 Washer 17x124
14 Bolt, Hex 1x153
15 Blade, Side Discharge 42225E701
Blade, Mulcher 1101120E701
16 Adapter, Blade 672503
17 Height, Adjuster, Right Frt. 672642
18 Height, Adjuster, Right Rr. 672644
19 Guard, Rear 672738
20 Screw 26x245
21 Deflector, Chute 672421
22 Push-On Cap 28x42
23 Pin, Pivot 215x11 Z
24 Spring 166x5
25 Baffle 672744E701
26 Wheel and Tire, Drive # ----27 Pulley 71434
28 Pin, Spring 32x64
29 Base, Engine 672671
30 Cover, Belt (Black) 1101025
31 Screw 26x279
32 Bracket, Idler Support 1101240 Z
33 Washer 17x102
34 Screw 26x263
35 Idler, Backside 71778
36 Locknut 15x43
* Parts are available from an Authorized Engine Service Center. See Engines, Gasoline" or Gasoline
Engines" in the yellow pages of the telephone directory.
# See the Wheel And Tire Parts List" page.
F–030406L
KEY
NO. DESCRIPTION PART NO.
37 Bearing 71793
38 Spring 166x45
39 Spacer 71789
40 Arm, Pivot 1101121 Z
41 Spacer 71788
42 Pulley, Idler 71779
43 Bolt, Shoulder 9x50
44 Belt, Briggs & Stratton
Belt, Tecumseh
45 Washer 17x186
46 Ring, Retainer 11x16
47 Gear, Pinion 71792
48 Pulley 71791
49 Pin, Drive 43629
50 Pin, Hair 31x9
51 Axle 672508
52 Washer 17x169
53 Cover, Dust 71780
54 Bolt 1x85
55 Hub Cap 43615
56 Plate, Mulch 672422 Z
57 Washer 17x67 Z
58 Knob, Axle 672449
59 Bracket, Left Handle 1101305E700
60 Bracket, Right Handle 1101304E700
61 Brace 672728E700
62 Screw 26x263
63 Bolt 1x120
64 Screw 26x289
65 Screw 26x288
66 Shield, Debris 1101026E701
67 Washer 17x45
68 Bolt, Carriage 2x86
69 Bolt 1x81
- Book, Instruction F-030406L
27
37x100
37x101
WHEELS AND TIRES
Look at the illustrations. Select the wheel and the tire you want and order
from the following chart.
A
B
WHEEL SIZE & TYPE A B C D
6–inch Plastic, White 672768 –––– –––– ––––
6–inch Plastic, Gray 672769 –––– –––– ––––
7–inch Plastic, White 20270 –––– –––– ––––
C
D
7–inch Plastic, Gray 71597 –––– –––– ––––
8–inch Plastic, White 20271 –––– –––– ––––
8–inch Plastic, Gray 672060 71132 –––– ––––
8–inch Metal, White 43414 –––– –––– ––––
8–inch Ball Bearing, Gray –––– 71134 –––– ––––
14–inch, Gray –––– –––– 672074 672745
14–in, Ball Bearing, Gray –––– –––– 672062 71840
F–030406L
28
NOTES
F–030406L
29
NOTES
F–030406L
30
F–030406L
31
Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where
HOW TO ORDER REPAIR PARTS
the unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow
pages of the telephone directory. If you cannot get a repair part or service as described above, call or write to the Central
Parts Distributor shown below. When you order, include the following information: (1) Complete Model Number (see
nameplate), (2) Date of Manufacture, (3) Complete Part Number, (4) Description, (5) Quantity.
Repair parts for the engine or the transmission are available from the manufacturer's authorized service center found
in the yellow pages of the telephone directory. See the individual engine or transmission warranties.
MURRAY, INC. LAWN MOWER CENTRAL PARTS DISTRIBUTORS
BEBCO, INC.
2221 2nd. Ave.
South Birmingham, AL. 35233
(205)251-4600ă1-800-828-8094
Alabama, Florida, Georgia,
Puerto Rico
BILLIOU'S, INC.
1343 South Main St.
Porterville, CA. 93257
(559)784-4102ă1-877-245-5468
FAX 1-800-266-7337
Arizona, California, Hawaii,
Nevada
BROWN & WISER, INC.
9991 S.W. Avery Street
P.O. Box 1109
Tualatin, OR. 97062
(503)692-0330ă1-800-882-4782
Alaska, Idaho (counties Ada,
Adams, Benewah, Boise, Bonner,
Boundry, Canyon, Clearwater,
Elmore, Gem, Idaho, Kooten,
Latah, Lewis, NEZ Perce, Owyee,
Payette, Ravalli, Shoshone, Valley,
Washington), Montana (counties
Flathead, Lake, Lincoln, Mineral,
Missoulo, Ravalli, Sanders),
Oregon, Washington
CPT CANADA POWER
TECHNOLOGY LIMITED
161 Watline Avenue
Mississauga, Ontario
L4Z-1P2
(905)890-6900ă1-800-861-9559
101-10411-178 Street
Edmonton, Alberta
T5S 1R5
(780)453-5791ă1-800-861-9559
234 Migneron Street
Ville St-Laurent, Quebec
H4T 1Y7
(514)731-3559ă1-800-861-9559
Canada
F–030406L
ENGINES SOUTHWEST
1255 North Hearne
Shreveport, LA. 71107
PO Box 67
Shreveport, LA. 71161
(318)222-3871ă1-800-388-6995
www.enginessw.com
Arkansas (except these counties:
Clay, Craighead, Crittendan, Cross,
Greene, Hempstead, Howard,
Jackson, Lafayette, Lawrence, Lee,
Little River, Miller, Mississippi,
Monroe, Nevada, Phillips, Pike,
Poinsett, Randolph, Sevier, St.
Francis, Woodruff) Louisiana,
Mississippi (except these
counties: Desota, Panola, Quitman
Tate, Tunica,)
FRANK EDWARDS CO.
3626 Parkway Blvd.
West Valley City, UT 84120
(801)736-8060ă1-800-318-0201
FAX 1-800-570-0491
Colorado, Idaho (counties
Bannock Bearlake, Bingham,
Blaine, Booneville, Butte, Camas,
Caribou, Cassia, Custer, Franklin,
Fremont, Gooding, Jefferson,
Jerome, Lemhi, Lincoln, Madison,
Minidoka, Oneida, Power, Teton,
Twin Falls) Montana (all counties
except Brown and Wiser), Utah,
Wyoming
GARDNER, INC.
1150 Chesapeake Ave.
Columbus, OH. 43212
(614)488-7951ă1-800-848-8946
Arkansas (counties Clay,
Craighead, Crittendan, Cross,
Greene, Jackson, Lawrence, Lee,
Mississippi, Monroe, Phillips,
Poinsett, Randolph, St. Francis,
Woodruff), Indiana, Kentucky,
Michigan (except upper
Peninsula), Mississippi (counties
Desota, Panola, Quitman, Tate,
Tunica), Ohio, Western
Pennsylvania with zip codes up to
and including 16999, Tennessee,
West Virginia
ă
GULF COAST ENGINE, INC.
4202 Russell Dr.
P.O. Box 9724
Corpus Christi, TX. 78408
(361)888-6999ă1-800-825-6999
Arkansas (counties Hempstead,
Howard, Lafayette, Little River,
Miller, Nevada, Pike, Sevier) New
Mexico, Oklahoma, Texas,
Mexico
OSCAR WILSON
ENGINE & PARTS
826 Lone Star Dr.
O'Fallon, MO. 63366
(314)978-1313ă1-800-873-6722
Illinois (S. of Hwy. 80), Iowa,
Kansas, Missouri, Nebraska
R.B.I. CORPORATION
P.O. Box 9318
Richmond, VA. 23227
(804)550-2210ă1-800-888-7149
FAX 1-800-947-1335
Connecticut, Delaware, District
of Columbia, Maine, Maryland,
Massachusetts, New Hampshire,
New Jersey, New York, N. & S.
Carolina, Pennsylvania zips
17000 & up, Rhode Island,
Vermont, Virginia
WISCONSIN MAGNETO
4727 N. Teutonia Ave.
Milwaukee, WI. 53209
(414)445-2800ă1-800-733-7388
Illinois (N. of Hwy. 80), Michigan
(upper Peninsula), Wisconsin
800 McKinley St.
Anoka, MN. 55303
(612)323-7477ă1-800-248-4016
Minnesota, North & South
Dakota
Loading...