PRE-ASSEMBLED MURPHY DOOR KIT INSTALLATION
1
JAMB CASING BOOKCASE
Jamb Side
Jamb Side
SHELVES
Jamb Top
(Threshold)
Jamb Bottom
Adjustable ShelfAdjustable ShelfAdjustable Shelf
Casing Top
Casing Side
Casing Side
MurphyDoor.com888-458-5911
2
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
To assemble the door you will need:
• Tape Measure
• Carpenters Square
• 2’ and 6’ Level
• Drill
• Countersink Bit
• Phillips Head Bit
• 1/8" Drill Bit
• Adjustable Wrench
• Hammer/Brad Nailer
• Finish Nails
• Wood Glue
JAMB CASING BOOKCASE
Jamb Side
Jamb Side
SHELVES
Jamb Top
(Threshold)
Adjustable ShelfAdjustable ShelfAdjustable Shelf
Casing Top
Casing Side
Casing Side
Jamb Bottom
E
(8) 7x50mm
Conrmat Screws
I
Top Hinge Plate
M
Friction Door Catch
P
(12) Shelf Pins Hinge Pin Removal Tool
F
(8) 3" Jamb Screws
J
Bottom Pivot Hinge
G
Upper Jamb Hinge
K L
(24) Flat Head Phillips
Sharp Point 1" Screws
N
Hinge Pin w/Ball Lock
Q
H
Bottom Jamb Hinge
(8) Flat Head Phillips
Sharp Point 3/4" Screws
O
Poly Wedge
D
(18) 1-1/4" Truss Head Screws
MurphyDoor.com888-458-5911
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
Right Hand,
In or Out-swing
3
1
Align the jamb bottom threshold and 1 jamb side on a at
surface. The pre drilled hinge holes on the jamb bottom
threshold will be on the right for a right hand in or out-swing,
on the left for a left hand in or out-swing. After ensuring the
corner is square; install (2) 7 x 50mm conrmat screws (E).
3
Place the door jamb into the rough opening. The bottom
jamb threshold should extend into the room toward the
back of the bookcase.
2
Secure and square remaining corners of the door jamb using
(6) 7 x 50mm conrmat screws (E).
4
It is critical that the bottom threshold and jamb sides are
level. If the door jamb is not level and plumb the door will
not swing and close properly.
Note: The bottom threshold SHOULD NOT be installed over carpeting.
Carpet will aect levelling and prevents proper function of the door.
5
Using a 1/8" drill bit pre-drill and countersink three holes
into each side of the door jamb 2" from the top of the jamb,
2" from the bottom of the jamb, and in the middle.
Next pre-drill and countersink two holes into the jamb top
6" from the right and left sides of the jamb.
6
Using shims where needed, install (8) 3" jamb screws (F)
making certain the top and sides of jamb are level.
Note: The screws included are meant for a wood frame. If installing
the jamb into a steel frame, replace the screws with (8)
screws.
MurphyDoor.com888-458-5911
3"
self-tapping
4
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
Right Hand,
In-swing
21
To install a right hand, in-swing door attach the upper jamb
hinge (G) to the jamb top using (4) at head Phillips sharp
point 1" screws (K), lining up the hinge as shown. For a left
hand door use the same pre-drilled hole on the opposite
side for all hinge placement.
23
Attach the top hinge plate (I) to the top bookcase assembly
using (4) at head Phillips sharp point 1" screws (K).
22
Install the bottom jamb hinge (H) to the jamb threshold using
(5) at head Phillips sharp point 1" screws (K), lining up the
hinge as shown.
24
Match the bottom pivot hinge (J) to the pre-drilled holes at
the bottom of the bookcase assembly as shown. With the
plate lined up attach using (4) at head Phillips sharp point
1" screws (K).
Right Hand,
Out-swing
25
For a right-hand, out-swing door attach the upper jamb hinge
(G) to the jamb top using (4) at head Phillips sharp point 1"
screws (K), lining up the hinge as shown. Make sure that you
only use four screws. DO NOT drill into the two holes closest
to the edge of the jamb as this can split your edge.
26
Install the bottom jamb hinge (H) to the jamb threshold using
(6) at head Phillips sharp point 1" screws (K), lining up the
hinge as shown.
MurphyDoor.com888-458-5911
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
5
27
Attach the top hinge plate (I) to the top bookcase assembly
using (6) at head Phillips sharp point 1" screws (K).
29
The friction door catch installs on the door side opposite
the hinge. Make a mark 2" from the back of the door’s
face frame.
28
Match the bottom pivot hinge (J) to the pre-drilled holes at
the bottom of the bookcase assembly as shown. With the
plate lined up attach using (6) at head Phillips sharp point
1" screws (K).
30
Position the friction door catch (M) at this mark, ush to the
door bottom. Secure using (4) at head Phillips sharp point
3/4” screws (L).
Place the door into the door jamb. Make sure the bottom
hinge sits in the silver thrust bearing.
3231
Press down on the ball lock of the hinge pin (N) to retract the
two top pins.
MurphyDoor.com888-458-5911
6
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
33 34
For an in-swing door align the holes of the bookcase top
jamb hinge with the holes of the top door hinge. Depress
the hinge pin button and insert the hinge pin into the holes
making certain the pin locks into place.
35
Place the poly wedge (O) where the doorstop carriage bolt
will go when the door is closed. Ensure that the door is ush.
Mark out the poly wedge location with a pencil.
For an out-swing door the hinge pin inserts from the front side
of the bookcase. Align the hole in the top of the bookcase with
the top door hinge. Depress the hinge pin button and insert
the hinge pin. The hinge pin will appear countersunk when
properly installed and locked into place.
36
Remove the sticker from the back of the poly wedge placing it
over the marked location. The wedge taper should face in for
an in-swing door and out for an out-swing door. Secure with
(4) at head Phillips sharp point 3/4” screws (L).
37
Now that the door assembly is in place use an adjustable
wrench to tighten the carriage bolt just enough to catch the
door catch.
38
Add (2) shelf pins (P) where desired and (2) shelf pins (P)
directly across from the rst two.
MurphyDoor.com888-458-5911
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
7
39
Slide the shelf into place onto the installed shelf pins.
Do the same to place the remaining shelves as desired.
41 42
Position the right and left side casings with a 1/2" overhang
on the face frame of the door. Attach using a brad nailer.
40
For an in-swing door, position the top casing with a 1/2" overhang
on the face frame of your door. Attach using a brad nailer.
In-swing Casing
Out-swing Casing
For an out-swing door, center the top casing over the door
leaving a 1/16" clearance over the door itself. Attach using
a brad nailer.
Trim the right and left casing to t as needed. Attach the right
casing onto the door jamb with a 1/2" overhang on the door
face frame.
4443
Using a 1/8" drill bit pre-drill ve holes into the left support
face frame. This will make it easier to attach the left side
casing.
MurphyDoor.com888-458-5911
8
PLEASE READ INSTRUCTIONS FULLY BEFORE YOU BEGIN ASSEMBLY
Out-swing
Casing
Run a bead of glue down the face frame of the door to
strengthen the left casing.
Out-swing
Casing
4645
Position the left side casing. Test the door swing prior to
screwing in to ensure it doesn’t make contact with the oor.
47
Secure with (5) 1-1/4" truss head screws (D) making sure not
to drill through other side of front casing.
Congratulations.
This completes the Murphy Door Unassembled Flush Mount
installation procedure.
1 Year Warranty (U.S.A. only)
Murphy Door warrants your door against defects in material and workmanship under normal use and maintenance for a
period of one (1) year from the date of original purchase.
Murphy Door Inc. will provide a replacement part for any part found to be defective. Original part(s) approved for return by
Murphy Doors customer service department must be returned prepaid. This warranty does not include labor charges
connected with the determination or replacement of defective parts, or freight charges to ship these parts.
Murphy Door Inc. shall not be liable under this or any implied warranty for incidental or consequential damages. This warranty
gives the retail customer specic legal rights and the customer may have other rights which vary from state to state.
This warranty shall be void if the unit is not assembled or operated in accordance with the operation instructions provided with
this unit; the unit is re-sold or traded to another owner; components, accessories; or the user has abused or otherwise failed to
maintain the unit.
To process a warranty claim, Murphy Door requires you to register your product on our BILT app and proof of your date of
purchase. You should retain your sales slip or invoice with your valuable documents.
MurphyDoor.com888-458-5911
Loading...