Murdock H2O To Go BF15, H2O To Go BF16 Maintance Manual

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

BF15 & BF16 Series

Surface Mount Bottle Fillers

BF15 Series BF16 Series

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:

1.800.591.9360

Technical Assistance Fax: [phone]

NOTES TO INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing, electrical and other applicable codes.

LIMITED WARRANTY - UNITED STATES & CANADA

Murdock warrants that its products are free from defects in material or workmanship under normal use and
service for a period of one year from date of shipment from the factory. Murdocks’s liability under this warranty
shall be discharged solely by repair or replacement of defective material, provided Murdock is notified in writing
within the time periods described above.

This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of
the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of
all other warranties expressed or implied. Product maintenance instructions are issued with each unit and
disregard or non-compliance with these instructions will constitute an abnormal use condition and void the
warranty. Stainless steel must be protected on jobsite during construction and must be properly maintained
after the water has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is
void.

LIMITED EXPORT WARRANTY - One year on parts only.

Murdock™ assumes no responsibility for use
of void or superseded data. © Copyright
Murdock Mfg., City of Industry, CA Member of
Morris Group International. Please visit

www.murdockmfg.com for most current

specifications.

7020-957-001 Date: 08/02/19

COMPLIES WITH

Federal
Public Law
111-380
(No Lead)

Member of

www.murdockmfg.com

MURDOCK

15125 Proctor Ave.
City of Industry, CA

91746 U.S.A.

Phone [phone]

626-336-4561

Fax [phone]

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

PRIOR TO INSTALLATION

Important: Some options may slightly alter installation. To ensure proper installation, review the manual thoroughly and verify
rough-ins before beginning any work. File this Manual with the owner or maintenance personnel upon completion of installation.

— Fixture mounting requirements: Industry standard wall construction, adequate to support the fixture and (installer provided) wall

anchors sufficient to secure the fixture.

— Fixture operates within water pressure range of 20 to 105 PSIG. Murdock will not warranty fixtures damaged when connected

to supply lines with flow pressure lower than 20 PSIG or higher than 105 PSIG.

— Per UPC 609.10- All building water supply systems in which quick acting valves are installed shall be provided with devices to

absorb the hammer caused by high pressure resulting from the quick closing of the valve. These pressure-absorbing devices
shall be approved mechanical devices. Water pressure-absorbing devices will be installed as close as possible to the quick
closing valve.

— Water supply inlet is 3/8” O.D. Copper Tube.
— Completely flush supply of all foreign debris before connecting to fixture. Bottle Filler is designed to provide trouble- free

drinking water unaffected by fixture connection tubing and fittings and not cause problems with taste, odor, color or sediment.

— Electrical Receptacle(s) must be wired to a GFCI protected circuit. Fixture must be earth grounded per N.E.C. (National

Electrical Code).

DIMENSIONAL DRAWING

Prior to roughing in, consult with local, state, and federal codes for proper mounting height.

BF15/16 Surface Mounted Bottle Filler

3

7

"

8

(187)

OPTIONAL -BCD BOTTLE

COUNTER AND FILTER

REPLACEMENT DISPLAY

LED LIGHTING

WITH -BCD OPTION

ONLY

1

18

4

[464]

GENERAL OTES:

1. ALL DIMENSIONS ARE IN INCHES (MM)

"

7

4

"

8

[124]

5

12

"

8

29

1

"

2

[321]

[749]

1

5

"

1

34

2

[876]

A.F.F.

"

12

1

"

8

[308]

8

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 2 of 13

Member of

Revised: 08/02/19

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS:

Surface Mounted Bottle Fillers

Place unit onto a horizontal surface. Unscrew Top Screws with 1/8"

1

Allen Wrench (not included) and place in a secure location for later
use. Open unit by swinging Mounting Panel down.

1

2

Remove Bottle Filler Housing from unit by removing one Screw from

2

the Hinge and sliding the Bottle Filler Housing out. Set aside for later
use in the Manual.

1

Bottle Filler Housing

2

Mounting Panel

3

#10-32 x 3/4" Phillips Round Head Screw

1

#10-32 x 1" Allen Button Head Screw

2

Bottle Filler Housing

3

3

3

Mounting Panel

2

2

1

Locate and attach Mounting Panel to finished wall. Secure Mounting

3

Panel with Anchoring Hardware, provided by installer. See step four
for rough-in layout.

1

2

3

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

2

Page 3 of 13

1

Finished Wall

2

Mounting Panel

3

Anchoring Hardware, by others

1

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS CONTINUED:

Provide wall openings as indicated in rough-in detail provided, ensuring to block out the electrical service rough and Waste

4

outlet for 1-1/2" P-Trap. Use Mounting Panel as template.

1

18

"

29

3

3

"

4

TYP.

7

4

"

8

TYP.

1

9

"

2

TYP.

1

"

2

12"

TYP.

X X X

4

7"

C

L

6

4

5

3

General Notes:

1. Dimension indicated with (*) is for 34-1/2" deck
height. Adjust accordingly for preferred deck
height.

2. Anchoring is required for holes marked with
(X). Auxiliary holes available if required.

1

34

"

Deck Height Notch

2

A.F.F.

X X X

1

3

"

1

4"

1

*24

"

4

TYP.

A.F.F.

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

7

*27

8

A.F.F.

"

2

1

6

"

4

2

*26

A.F.F.

Page 4 of 13

1
4

*29

A.F.F.

"

1

"

8

110VAC Electrical Duplex1
Receptacle, by others

2

3/8" NCT Supply Inlet

3

Waste Outlet for 1-1/2" P-Trap

4

Mounting Panel

5

Ø1/4" Holes, for Anchoring
Hardware, by others

6 Housing, Shown for Ref.

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS CONTINUED:

With the Mounting Panel secured to finished wall, install P-Trap Waste
Outlet. P-Trap must not extend more than 4-1/4" from finished wall.

1

4

4

Max

Top View

Connect 3/8" O.D. "Y" Strainer to main water supply. Recommend
using angle stop for easy maintenance. Angle stop must not extend
more than 3-1/2" from finished wall.

1

Mounting Panel

2

Angle Stop Recommended,
by others

3

"Y" Strainer

1

Mounting Panel

2

P-Trap

3

Drain Tray

"

1

3

"

2

Max

Re-mount Bottle Filler Housing by reversing steps taken in Step 2.

1

Bottle Filler Housing

2

Mounting Panel

3

#10-32 x 3/4" Phillips Round Head screw

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 5 of 13

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS CONTINUED: (BF15)

With Bottle Filler Housing secured to unit, connect water supply line.

8A

Keep supply line within plastic cable holders to prevent supply line
from getting pinched or damaged. If Fixture is BF16, see steps 8B-9B.

1

4

5

2

1

Mounting Panel

2

Bottle Filler Housing

3

Valve Water Supply Outlet Elbow

4

Bottle Filler Water Supply Inlet Tubing

5

Plastic Cable Holder

1/4"

Min.

3

1

Mounting Panel

2

Bottle Filler Housing

3

1/8" O.D. Polyethylene Air Line

4

Valve Air Line Inlet

5

Plastic Cable Holder

With Water Supply Line properly secured, connect 1/8" O.D.

9A

Polyethylene Air Line to valve. Keep Air Line within the plastic cable
holders to prevent supply line from getting pinched or damaged.
Turn on water and check for Leaks throughout the system.

1

5

2

3

4

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 6 of 13

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS CONTINUED: (BF16)

With Bottle Filler Housing secured to unit, connect water supply line

8B

and electrical wiring as shown below. Keep supply line and wiring
within plastic cable holders to prevent supply line and wiring from
getting pinched or damaged. If fixture is BF15, see steps 8A-8B.

1

7

3

4

6

5

2

1

Mounting Panel

2

Bottle Filler Housing

3

Solenoid Valve Electrical Wiring

4

Bottle Counter Display / Sensor Wiring

5

Solenoid Valve Water Supply Outlet Elbow

6

Bottle Filler Water Supply Inlet Tubing

7

Plastic Cable Holder

1

Mounting Panel

2

Bottle Filler Housing

3

Power Supply

4

110VAC Duplex Receptacle

Plug-in power supply, turn on water and check for leaks

9B

throughout the system.

4

3

1

2

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 7 of 13

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

INSTALLATION INSTRUCTIONS CONTINUED:

With fixture tested, hook Lanyard from Bottle Filler Housing to

10

Mounting Panel and tighten Screw.

3

4

2

1

11

1

Bottle Filler Assembly

2

#10-32 x 1" Allen Button Head Screw

3

Bottle Filler Housing

4

Mounting Panel

1

Bottle Filler Housing

2

Lanyard

3

Mounting Panel

4

Lanyard Mounting Screw

2

Lift up from Fill Spout area to close the unit by swinging Bottle Filler
Housing up and secure with Screws from step 1. Do not force closed.
Address any interference if necessary. Do not over-tighten.

4

2

3

To open unit for maintenance purposes, remove Top Screws. Lift

12

Bottle Filler Housing up from Fill Spout area then pull away from wall.

2

1

3

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 8 of 13

4

1

Bottle Filler Assembly

2

#10-32 x 1" Allen Button Head Screw

3

Bottle Filler Housing

4

Mounting Panel

1

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

ELECTRICAL INSTALLATION:

NOTE: PLUG-IN POWER IS A STANDARD FEATURE FOR BF16.

1A. Plug-In Operation: Plug transformer provided into GFCI protected electrical service, used by the Bottle Filler.

2. Connect the Sensor Wires to either the Solenoid Valve or -BCD Bottle Counter Display (if equipped).

START UP:

1. Air within the Bottle Filler System or the structure supply piping will cause an irregular Spout outlet stream until
purged out by incoming water. Hold cup (or similar object) directly below Filler Spout is recommended when first
activating Bottle Filler to prevent excessive splashing. Activate sensor until steady water stream is achieved.

OPERATING INSTRUCTIONS:

Position container to be filled directly in front of the Sensor and centered under the Filler Spout. Water flow starts

automatically. When the container is almost filled, remove container. The water will stop flowing.

BOTTLE COUNTER ADJUSTING & RESETTING INSTRUCTIONS:

NOTE: Bottle Counter Has Multiple Functions

Reset/ Mode Button

• Counts refilled bottles

• Adjustable for units with and without Filters

• “REPLACEMENT FILTER” alert function

• Alert reset, when Filter is replaced

Description

Illuminated LCD Display counts bottles and has a Filter replacement alert function.

Bottle Counting Function

The software applies a flow volume of approximately 16.9 fl oz (volume in standard size plastic water bottle) to
each bottle counted. If the flow volume is less than 16.9 fl oz, there will be no count but the volume will
accumulate, so that part way through the next cycle the total bottle count will change.

-BCD Bottle Counter Display
with Illuminated Display

Fill Spout

Sensor

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 9 of 13

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

FILTER REPLACEMENT FUNCTIONS:

NOTE: When the volume accumulates to programmed Filter volume, the “REPLACE FILTER” alert will

appear on the display every time the Bottle Filler is activated.

Counter Modes:

Located on the back of the Display you will find the Reset/Mode Button for the mode settings. The
Reset/Mode Selection Button is accessible by removing the Housing, then locate the large hole in the back of
the Display Mounting Bracket. Use your finger or nonconductive object to depress the Reset/Mode Selection
Button.

CAUTION: DO NOT USE SHARP OR METAL OBJECTS!!!

With this Reset/Mode Button, you are able to indicate whether the unit has a Filter or does not have a Filter.
The Reset/Mode Button is used to remove the “REPLACE FILER” alert after the Filter has been replaced.

Systems With or Without Filter:

•To reset “REPLACE FILTER” message:

-Press and hold Button until “3” is displayed, then release.

•To change display to match Filter capacity:

-Press and hold Button until the Display matches installed Filter type, then release.

“FILTER NONE”
“FILTER 1500”
“FILTER 3000”

RESET/MODE

BUTTON

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 10 of 13

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

PUSH-IN FITTING INSTALLATION

NOTE: FITTINGS AND TUBE SHOULD BE KEPT
CLEAN, BAGGED AND UNDAMAGED PRIOR TO
INSTALLATION.

TO CUT TUBE:

Cut to fit length of 1/4” PE Tubing and remove any
burrs or sharp edges. Ensure that the outside diameter
is free from score marks. Tube ends should be square.

INSERTING THE TUBE:

1. Firmly and fully insert the Tubing end into the Push-In
Fitting up to the Tube Stop located approximately 1/2”
deep.

2. Pull on the fitted Tubing to ensure it is secure. Tube

should not come free from the Fitting. Water test the
connection assembly prior to leaving the site to ensure
there are no leaks.

DISCONNECTING THE TUBE:

Prior to disconnecting the Tube from the Fitting, ensure
that the water line is depressurized. Push Collet Square
towards the Push-In Fitting Body and hold. While holding
the Collet in, pull on the PE Tubing to remove from the
Push-In Fitting.

O-RING

O-RING

COLLET

TUBE STOP

COLLET

COLLET

COLLET

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 11 of 13

COLLET

Member of

Revised: 08/02/19

Surface Mounted Bottle Fillers

ITEM #

PART NUMBER DESCRIPTION ITEM #
1 7014-27 1-002 WALL MOUNTED FRAME ASSY., BF15/16 7 7012-055 -000 FOAM PIPE INSULATION
2 CONTACT FACTORY HOUSING ASSEMBLY, BF16-BCD 8 1895-709 -000 ELBOW, 1/4" PUSH-IN X 1/4" STEM
3 4970-26 5-000 P-TRAP 9 2150-005 -199 1/8" O.D. LLDPE TUBING, CLEAR
4 0116-12 3-000 #10-32 x 1" BUTTON HEAD SCREW 10 2566-16 0-001 PBH S/T SIDE OUTLET PUSHBUTTON
5 7000-02 1-001 "Y" STRAINER 11 7001-20 3-001 AIR-TROL VALVE & BRACKET ASSY
6 2169-00 0-000 1/4" O.D. LLDPE TUBING, BLUE

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

BF15 PARTS LIST
BOTTLE FILLER PARTS
BREAKDOWN

9

10

1

11

4

6

7

5

8

2

3

PART NUMBER DESCRIPTION

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 12 of 13

Revised: 08/02/19

Member of

Surface Mounted Bottle Fillers

ITEM #

ITEM #
1 701 4-271-002 WALL MOUNTED FRAME ASSY., BF15/16 9 011 6-123-000 #10-32 x 1" BUTTON HEAD SCREW
2 701 4-270-001 HOUSING ASSEMBLY, BF16-BCD 10 7000 -021-001 "Y" STRAINER
3 497 0-265-000 P-TRAP 11 2169-000-000 1/4" O.D. LLDPE TUBING, BLU E
4 256 3-381-001 SEN SOR "A" ASSEMBLY 12 7012-055-000 FOAM PIPE INSULATION
5 011 0-012-000 #6 x 3/16 " TRUSS HEAD SCREW 13 7001-200-001 SOLENOID / VALVE MOUNTING ASSY
6 071 6-111-001 BOTTLE COUNTER WITH CONNECTORS 14 0710-731-001 POWER SUPPLY
7 011 0-011-000 #6 x 3/16 " PAN HEAD SCREW 15 1895-709-000 ELBOW, 1/4" PUSH -IN X 1/4" STEM
8 701 4-253-199 SPLASH GUARD

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

BF16 PARTS LIST
BOTTLE FILLER PARTS
BREAKDOWN

7

8

7

6

14

1

13

9

1211

10

5

4

2

PART NUMBER DESCRIPTION

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-957-001

Page 13 of 13

PART NUMBER DESCRIPTION

15

3

Member of

Revised: 08/02/19