Murdock A481408S-CUSP, A481, A481408S, A481408F Maintance Manual

CONTEMPORARY WATER COOLERS

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

DRINKING FOUNTAINS

A481.8 Series

Barrier Free, Wall Mounted Electric Drinking Fountain

A481408S-CUSP / A481408F / A481408S

TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:

1.800.591.9360

Technical Assistance Fax: [phone]

NOTES TO INSTALLER:

1. Please leave this documentation with the owner of the fixture when finished.

2. Please read this entire booklet before beginning the installation.

3. Check your installation for compliance with plumbing, electrical and other applicable codes.

LIMITED WARRANTY - UNITED STATES & CANADA

Murdock warrants that every cooler, bottle filling station, packaged water chiller, fountain and accessory to be free
from defects in material and workmanship under normal use for one (1) year from date of install or eighteen (18)
months after the date of shipment from the factory, whichever comes first.

Murdock warrants the compressor and hermetically sealed refrigeration system, including cooling coil assembly
when part of the hermetically sealed refrigeration system, to be free from defects in material and workmanship
under normal use for an additional four (4) years from the end of the one (1) year period described above.

This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all
other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard
or non-compliance with these instructions will constitute an abnormal use condition and void the warranty.
Stainless steel must be protected on job site during construction and must be properly maintained after the water
has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is void.

LIMITED EXPORT WARRANTY - One year on parts only.

Murdock assumes no responsibility for use of void or
suspended data. © Copyright Murdock, City of
Industry, CA Member of Morris Group International.
Please visit www.murdockmfg.com for most
current specifications.

Federal

Test rating conditions are

Public Law
111-380

compliant with ARI 1010.

(No Lead)

7020-100-001 Date: 07/25/18

COMPLIES WITH

Member of

MURDOCK

15125 Proctor Ave.
City of Industry, CA

91746 U.S.A.

Phone [phone]

626-336-4561

Fax [phone]

www.murdockmfg.com

CONTEMPORARY WATER COOLERS

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S

DRINKING FOUNTAINS

ROUGHING-IN AND DIMENSIONAL DRAWING

Prior to roughing consult with local, state, and federal codes for proper mounting height.

17" WALL
OPENING

12"

WALL

OPENING

5

"

8

25

*41

22" - 40"

1

9

"

2

1

"

2

3

1

"

8

1

31

"

8

1

"

8

7

4

8

GENERAL NOTES:

1. ALL DIMENSIONS ARE IN INCHES.
*2. DIMENSIONS SHOWN ARE FOR RECOMMENDED ADULT HEIGHT. ADJUST VERTICAL

DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES.

3. STOP VALVE NOT PROVIDED.

*

36

WASTE

SUPPLY

"

6"

2"

5

"

8

&

(4) Ø

35"

ACCESS
PANEL

1

" MTG

8

HOLES

CUSPIDOR

SUPPLIED MOUNTING

3/8" O.D.

COPPER TUBING

FRAME

CHILLER

UNIT

1

54

"

2

WALL

OPENING

7

*

10

"

8

(2) 1-1/4" OD SLIP
JOINT WASTE
CONNECTION

IMPORTANT:

1. Waste P-Trap and Water Supply Service Stop Valve to be supplied by others in accordance with
local codes.

2. Water supply is 1/2” male NPSM (Cuspidor) & 3/8” copper tube (Fountain). See Figure “D”. Waste is
1-1/4” OD female slip joint connection.

3. Completely flush supply lines of all foreign debris before connecting to fixture. Optional water filter is
available should there be problems from the water supply with taste, odor, color, or sediment.

4. WARNING: Warranty is voided if installation is not made following current Acorn Aqua installation
instructions and if components are assembled to the fixture that are not approved by Acorn Aqua.

5. Fixture operates within water pressure range of 20 to 105 psig. Acorn Aqua will not warranty fixtures
damaged when connected to supply lines with flow pressure lower that 20 psig or higher than 105
psig. A pressure regulator must be furnished by others on supply line if inlet pressure is greater than
105 psig.

MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com

7020-100-001
Page 2 of 6

A481.8

Member of

Revised: 07/25/18