WLAN6090SD
Wireless LAN SDIO Card Datasheet
Preliminary Version
V 0.1
Confidential Information
Note: SyChip, Inc. reserves the right to make changes in specifications at anytime and without notice.
The information furnished in this data sheet is believed to be accurate and reliable. However, no
responsibility is assumed by SyChip for its use, nor any infringements of patents or other rights of third
parties resulting from its use. No license is generated under any rights of SyChip or its supporters unless
specifically agreed.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A
CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A
RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.
HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A
PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE
TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE
EQUIPMENT OFF AND ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE
INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA.
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER.
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO
WHICH THE RECEIVER IS CONNECTED.
- CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP.
WLAN6090SD Data Sheet
Document Version Control
Version Date Remarks
Initial draft V0.1 3/9/04 Initial Release
WARNINGS
THIS EQUIPMENT COMPLIES WITH PART 15 OF THE FCC RULES. ANY CHANGE OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS DEVICE WAS EVALUATED FOR BODY SAR IN A PDA WITH A SEPARATION DISTANCE
OF 0.5 MM. FAILURE TO INSTALL THIS DEVICE AS DESCRIBED WILL RESULT IN A
FAILURE TO COMPLY WITH FCC RULES FOR EXPOSURE AND IS DISCOURAGED. ONLY
ANTENNAS APPROVED WITH THE DEVICE MAYBE USED. NO EXTERNAL ANTENNAS MAY
BE USED. THIS DEVICE MAY NOT BE CO-LOCATED WITH OTHER TRANSMITTERS
WITHOUT FURTHER APPROVAL BY THE FCC. THIS DEVICE HAS NOT YET BEEN TESTED
FOR HEAD SAR AND AS SUCH IS NOT APPROVED FOR USE WITH ANY SMARTPHONE
DEVICE OR PDAS WITH BUILT IN PHONE CAPABILITY.
SyChip Confidential Page 2 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
Table of Contents
TABLE OF CONTENTS...............................................................................................................................................3
LIST OF FIGURES .......................................................................................................................................................4
LIST OF TABLES.........................................................................................................................................................4
1 INTRODUCTION .............................................................................................................................................5
1.1 Overview.........................................................................................................................................................................5
1.2 Key Features...................................................................................................................................................................5
1.3 Certifications.................................................................................................................................................................. 6
2 WLAN6090SD ARCHITECTURE....................................................................................................................7
2.1 SDIONow! Interface...................................................................................................................................................... 8
2.2 Operating systems support............................................................................................................................................8
2.3 UI language localization................................................................................................................................................8
2.4 International channel settings....................................................................................................................................... 8
2.5 WLAN security .............................................................................................................................................................. 9
2.6 LED specification...........................................................................................................................................................9
2.7 DC Electrical Specifications........................................................................................................................................ 10
2.8 Rx/Tx Specifications....................................................................................................................................................11
2.9 Absolute maximum ratings and reliability................................................................................................................11
PACKAGING OUTLINE.............................................................................................................................................15
2.10 Physical dimensions..................................................................................................................................................... 15
2.11 Pin configuration..........................................................................................................................................................16
2.12 Bulk packaging.............................................................................................................................................................16
3 ORDERING INFORMATION.........................................................................................................................18
3.1 WLAN SDIO card naming convention...................................................................................................................... 18
SyChip Confidential Page 3 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
3.2 Sample orders...............................................................................................................................................................18
3.3 Production orders........................................................................................................................................................18
4 TECHNICAL SUPPORT................................................................................................................................19
List of Figures
FIGURE 1 SYCHIP WIRELESS LAN SDIO CARD (REFERENCE PICTURE ONLY) ..........................6
FIGURE 2 WLAN6090SD FUNCTIONAL BLOCK DIAGRAM...............................................................7
FIGURE 3 WLAN6090SD GEOMETRY...................................................................................................15
List of Tables
TABLE 1 WLAN CHANNEL CENTER FREQUENCIES..........................................................................8
TABLE 2 REGIONAL CHANNEL REQUIREMENTS ..............................................................................9
TABLE 3 LED BLINKING PATTERN SPECIFICATION.........................................................................9
TABLE 4 DC ELECTRICAL SPECIFICATION .......................................................................................10
TABLE 5 RX/TX SPECIFICATIONS *.....................................................................................................11
TABLE 6 ABSOLUTE MAXIMUM RATINGS........................................................................................11
TABLE 7 PERFORMANCE CHARACTERIZATIONS............................................................................12
TABLE 8 MECHANICAL STRESS TESTS..............................................................................................13
TABLE 9 ELECTRICAL & ENVIRONMENTAL STRESS TESTS.........................................................14
TABLE 11 MECHANICAL SPECIFICATIONS .......................................................................................15
TABLE 12 PIN DEFINITION IN SDIO CARD.........................................................................................16
SyChip Confidential Page 4 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
1 Introduction
1.1 Overview
SyChip Inc. introduces the Low Power WLAN6090SD SDIO form factor Network Interface Card (NIC)
incorporating the popular Wireless Ethernet standard, 802.11b. This is the first available combination
SDIO card to incorporate both WLAN and memory functions. It uses Direct Sequence Spread Spectrum
(DSSS) Wireless LAN technology to provide bandwidths of up to 11Mbps and ranges of up to 1000 feet*.
The card incorporates 256MB of flash memory for storage applications. The card enables next generation
power sensitive PDAs, cellular phones, and ultra-thin notebooks to access and store information from the
Internet, email, corporate networks, receive streaming video or audio and share images or large files in a
WLAN-enabled environment. The design has been targeted for battery sensitive applications where
battery capacity is at a premium and/or the host device needs to be used for extended periods without
recharging. The card is ideal for portable equipment where there is only one SD slot available for
peripheral devices. The configuration utility allows user selection and optimization of both performance
and battery life. In addition, the utility also allows users to be able to select an Access Point Search
Threshold based on the Access Point Density. This optimizes the threshold at which the utility hands of
between one Access Point and another for seamless roaming and reduction in dropped connections.
In the consumer market, this WLAN card is ideal for users of Windows® based Pocket PCs, SmartPhones,
Printers and Scanners which incorporate an SDIO capable SD slot utilizing the BSquare SDIOnow!
Architecture1. In the future, the card will support Symbian
SDIO capable slot.
The WLAN6090SD NIC is a complete card design incorporating the Baseband processor, MAC,
Memory, VCO, Transceiver, Antenna, 256MB memory and all necessary software drivers for both
functions.
In addition the flexible driver design supports both Microsoft® WinCE Wireless Zero
Configuration (WZC) capabilities** and the SyChip configuration utility. This is especially beneficial
where enterprise customers require full control of the configuration setup.
®
This card will pass Wi-Fi
certification and the reference design has been FCC and CE certified to
ensure radio compliance in all regions
TM
OS based phone designs that incorporate an
1.2 Key Features
• Low Power design. Ideal for battery sensitive applications
• WLAN 802.11b and 256MB memory functions in a single card design
• Capability to control device for optimum power or performance depending on user need
• AP search threshold capability
• Capability to control device configuration through Windows Zero configuration or SyChip utility
for maximum flexibility**
• Wi-Fi® certified – interoperable with other Wi-Fi® certified WLAN products
• Very small footprint: Card Measurements: 57mm X 24mm
SyChip Confidential Page 5 of 19 SyChip_WLAN6090SD
Key Features (Cont.)
• Driver support for Microsoft
• Smart Utilities enhance user experience by simplifying the set up process
• High performance security via support for 40/128 bit WEP key, LEAP and WPA protocols
* Depending on environment and data throughput
** Applies to Microsoft PPC2003 only
Figure 1 Sychip Combo function SDIO NIC (reference picture only)
®
WinCE (v4.2 and higher)
WLAN6090SD Data Sheet
1.3 Certifications
WLAN6090SD is a complete WLAN solution incorporating the baseband processor, MAC, memory,
VCO, Transceiver, Antenna, Antenna Switch and power amplifier. The card is fully WiFi compliant, FCC
and Industry Canada approved, and will meet CE, TELEC, and Korean certification requirements.
• Wi-Fi is a registered trademark of the Wireless Ethernet Compatibility Alliance.
SyChip Confidential Page 6 of 19 SyChip_WLAN6090SD
R
r
R
r
WLAN6090SD Data Sheet
WLAN6090SD Architecture
BALUN
BALUN
RFIC
T/
BPF
BPF
T/
Switch
Switch
PA
PA
RFIC
Direct Conversion
Direct Conversion
Loop
VCO
VCO
Loop
Filte
Filte
Figure 2 WLAN6090SD Functional Block Diagram
The WLAN6090SD is a completed Combo 802.11b Wireless LAN plug-and-play Network Interface Card
(NIC) and memory card for Pocket PC and handheld devices.
TX I/Q
TX I/Q
RX I/Q
RX I/Q
TX AGC
TX AGC
BB AGC
BB AGC
44 MHz
44 MHz
Clocking
Clocking
BBC/MAC
BBC/MAC
32 KHz
32 KHz
Crystal
Crystal
SDIO I/F
SDIO I/F
IC
IC
Flash Memory
Flash Memory
+ Controller IC
+ Controller IC
Host
The WLAN6090SD NIC is built with the chip set consisting of an RF Transceiver, Power Amplifier,
Baseband Processor aswell as 256MB of NAND MLC flash memory. The block diagram in Figure 2
shows the main functional components in the system. The memory bock includes an intelligent controller
that manages interface protocols and data storage and retrieval as well as Error Correction Code (ECC)
algorithms, defect handling and diagnostics, power management and clock control.
The RFIC radio transceiver includes a LNA, a transmit pre-amplifier, a quadrature up/down converter, a
synthesizer, a low pass filter, and an Rx amplifier. It utilizes Direct Conversion technology, eliminating
the need for intermediate-frequency mixer(s), amplifier and filter components.
The RF function in WLAN6090SD covers all of the RF channels frequencies specified in 802.11b
standard, operating in the IMS frequency band from 2.4 GHz to 2.5 GHz.
The Baseband Processor is a highly integrated Baseband /MAC which complements the RFIC radio
transceiver. The SDIO interface IC enables the SD 1-bit mode and SD 4-bit mode communications with
the host.
WLAN6090SD provides bandwidths of up to 11Mbps. The WLAN6090SD card can adjust its transmit
/receive speed to 1, 2, 5.5, or 11Mbps using dynamic throughput management. This technique ensures
that the WLAN6090SD NIC is performing at the optimal transmission rate for various environments and
communication ranges.
The WLAN6090SD supports a 3-wire protocol that allows for status reporting between the 2 functions,
allows for correct command/response handling and correct initialization and de-initialization sequences.
The device can be used in a stand alone mode for either memory in an SD only enabled host or for
WLAN functionality in a single function SDIO host.
SyChip Confidential Page 7 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
Product Specifications
1.4 SDIONow! Interface
The WLAN6090SD interface supports the Bsquare SDIO Now!1 Architecture. The device drivers for
WinCE OS versions support SD 1-bit and SD 4-bit I/O mode.2
The Sychip SDIO interface ASIC is designed to utilize the full potential of SD bus bandwidth, 25Mbps in
1-bit mode, and 100Mbps in 4-bit mode.
1.5 Operating systems support
The WLAN6090SD card driver currently supports the following Operating Systems:
Win CE 4.2 and WinCE.NET
The driver utility User Interface (UI) currently supports
PPC 2003
1.6 UI language localization
The card User Interface (UI) is in English only as general offering.
The UI can be customized to support other localized language appearance. Sychip can provide UI
resource file template utility to enable a customer to implement the language localization.
1.7 International channel settings
The WLAN SDIO card uses frequencies in the 2.4 GHz to 2.5 GHz ISM band, as defined by IEEE 802.11
standards.
Table 1 WLAN channel center frequencies
Ch # 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Freq.
2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 2484
MHz
Channel numbers 1~11 are available as standard and can be used in most regions worldwide. The cards
can be configured for the operation channels in accordance with the required regulatory authority.
1
SDIO Now! is a trademark of BSquare. This will be the same architecture that will be employed by Microsoft in their next
generation OS
2
The WLAN6090SD hardware interface supports both SD modes and the SPI mode.
SyChip Confidential Page 8 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
Table 2 Regional channel requirements3
Zone Region/Countries Channels Comments
Zone 1 North America (NA) USA & Canada 1 ~ 11
Zone 2 Europe/CEPT (ETS)= most of Europe,
Australia, Korea
Zone 3 France (FR) 10~13 Not supported
Zone 4 Japan (JP) 1 ~ 14
Zone 5 Spain (SP) 10~11 Not supported
1.8 WLAN security
Security is one of the requirements in wireless communications. It is critical to enterprise users as well as
to the SOHO and residential users.
1.8.1 WEP support
The WLAN6090SD has built-in 64-bit/128-bit WEP key support.
1.8.2 LEAP support
The WLAN6090SD can support Cisco LEAP via a third-party supplicant for WinCE 3.0 (PPC2002).
1 ~ 13
1.8.3 IEEE 802.1x authentication
The WLAN6090SD adopts IEEE 802.1x authentication framework and supports a set of EAP (Extensible
Authentication protocol) types with Microsoft PPC2002 and PPC2003 environment.
1.8.4 Wi-Fi WPA and IEEE 802.11i
Wi-Fi WPA is a subset of the IEEE 802.11i security standard. It supports enterprise-level mutual
authentication and enhanced encryption.
The WLAN6090SD will support native WPA functionality in PPC2003 when made available through a
future release by Microsoft.
1.9 LED specification
The WLAN6090SD card has a built-in visible LED. Its activity is used to indicate the card status. The
blinking pattern and information carried is listed in Table 3.
Table 3 LED blinking pattern specification
LED Specification
State LED Pattern
Radio Disabled Off
Radio enabled, associating Blinking
Radio enabled, connected to network Continuous on
3
Zone 3 (France), zone 5 (Spain) are not currently supported due to the very low transmitting power regulations in these
regions
SyChip Confidential Page 9 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
1.10 DC Electrical Specifications
Table 4 DC electrical specification
Parameter Condition Min Typical Max Units
Supply Voltage (Vcc) 2.7 3.3 3.6 V
Current (Receiving) 3.3V, continuous Rx
Both functions operational
Current (Transmitting) 3.3V, continuous Tx
Pout = 13 dBm
Both functions operational
Current (Receiving) 3.3V, Continuous Rx,
Memory function only
Current (Transmitting) 3.3V Continuous Tx
Memory function only
Current (Deep-sleep4) –
WLAN + memory functions
Current (Deep-sleep) –
Memory only function
Current (Average5) – WLAN
+ Memory functions
Logic high input 0.7Vcc V
Logic low input 0.3Vcc V
Logic high output Vcc – 0.2 V
Logic low output 0.1 0.2 V
3.3V, power-save enabled 6 mA
3.3V 40 µA
3.3V, power-save enabled 20 mA
250 mA
270 mA
20 mA
25 mA
4
Deep-sleep current reflects the idle current level when 32 KHz clocking is engaged. The radio is turned off; the MAC and the
SDIO I/F are operating at the reduced clock rate.
5
Average current includes the beacon interactions and the idle periods in deep-sleep mode. The 200 ms beacon period is used
for the reading.
SyChip Confidential Page 10 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
1.11 Rx/Tx Specifications
Table 5 Rx/Tx specifications *
Parameter Condition Min Typical Max Units
Physical Layer Data Rate 1 Mbps
2 Mbps
5.5 Mbps
11 Mbps
Frequency Range Based on channel center
frequency
Frequency Tolerance +/- 25 ppm
Carrier Frequency Suppression 35 dBc
Output Power6 3.3V 13 dBm
Transmit Spectral Mask 1st Side-lobe, 3.3V -30 dBc
Transmit Spectral Mask 2nd Side-lobe, 3.3V -50 dBc
Sensitivity 1Mbps, 3.3V -90 dBm
2Mbps, 3.3V -88 dBm
5.5Mbps, 3.3V -87 dBm
11Mbps, 3.3V -83 dBm
Memory Capacity (MLC Flash) 256 M Bytes
Memory Read Access Speed FClk = 20MHz 10 Mb/sec
Memory Write Access Speed 3 Mb/sec
* All at 25oC room temperature
2412 2484 MHz
1.12 Absolute maximum ratings and reliability
The tables in this section summarize the reliability tests and qualifications the WLAN6090SD cards
passed. The Full WLAN6090SD Network Interface Card Product Reliability & Qualification Report is
available upon request.
1.12.1 Absolute maximum ratings
Table 6 Absolute maximum ratings
Parameter Min Max Units
Operating Temperature -25 +60 °C
Storage Temperature -30 +80 °C
Supply Voltage Vcc +3.6 V
Input, Output I/O Voltage GND -0.5 +5.5
6
The output power range covers channels 1 to 13. To meet Japanese regulatory requirement for spread-spectrum processing
gain, Channel 14 uses an FIR spectrum shaping digital filter. The side effect is that the available Tx power is compromised by
2~2.5 dBm when using this filter.
SyChip Confidential Page 11 of 19 SyChip_WLAN6090SD
1.12.2 Product performance characterizations
Table 7 performance characterizations
Test Name Test Standard
PASS/FAIL Criteria
Low Temperature Tests
Receiver & Transmitter 0
High Temperature Tests
Receiver & Transmitter 80
Low Temperature
Storage Tests ( 0
168hrs(95% RH)
High Temperature
Storage Tests(80
168hrs(95% RH)
Power ON / OFF Cycling Tests PC card / SDIO Passed
o
o
C)-
C)
o
C
o
C
IEEE 802.11 spec Passed
IEEE 802.11 spec Passed
PC card / SDIO Passed
PC card / SDIO Passed
WLAN6090SD Data Sheet
Status & Results Comments
Limitation in Cabling
Done
-Only storage,
non-operational
As above
Done
-Only storage,
non-operational
As above
Done
-Only storage,
non-operational
As above
Done
-Only storage,
non-operational
1000 cycles through Hi
Done
Operational test
& Lo cycles
SyChip Confidential Page 12 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
1.12.3 Mechanical Stress Qualifications
Table 8 Mechanical stress tests
Test Name Test Standard
PASS/FAIL Criteria
Vibrations Test Customer Spec
15G, 10 to 2000 Hz @13.0 H/Min, 3 axis
Shock Test Customer Spec
50G @11 ms, 3 axis;30 shocks
Card Drop Test Industrial Spec
1.5m , non-cushioning vinyl floor , 6 axis
Insertion & Removal &
Insertion position Test
Insertion / Removal force Tests Customer Spec
Package Sheer Tests Industrial Spec
Package Drop Test Customer Spec
Card Bend Test Customer Spec- 19.6N cycle load (PC card) PASSED
Customer Spec
5000 K per slot- (3 pers)
SD 40 N
40 N cycle load
1.5m , non-cushioning vinyl floor , 6 axis
Status & Results
PASSED
PASSED
PASSED
PASSED
PASSED
PASSED
PASSED
Card Twist Test Customer Spec
(PC card) 10
Chip / die Sheer Test Mil STD-883E/2019
43, 100 & 45 kg 3 dies respectively
o
for 5 min for 5X
PASSED
PASSED
SyChip Confidential Page 13 of 19 SyChip_WLAN6090SD
1.12.4 Electrical & Environmental Stress Qualifications
Table 9 Electrical & environmental stress tests
Test Name
& ID
Moisture Sensitivity Tests
(Weight Gain Analysis)
Dynamic Operational Life Tests 168 hours -PCMCIA/-Card Environmental
Temperature Cycling Tests 100 cycles PCMCIA /-Card Environmental @
Temperature Humidity Test 168 hours –
Temperature Humidity & Bias
Tests
168 hours -PCMCIA/-Card
o
-0
C to 55 oC @ 95% RH
o
-0
C to 55 oC @95% RH
0 to 55
40 min/cycle
@ 95% RH
PCMCIA/-Card Environmental
168 hours @ 95% RH
PCMCIA/-Card Environmental
o
C
Test Standard
PASS/FAIL Criteria
WLAN6090SD Data Sheet
Status & Results
PASSED
-> 1% Moisture Absorption,
card recovered 100%
PASSED
PASSED
PASSED
PASSED
SyChip Confidential Page 14 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
Packaging outline
1.13 Physical dimensions
Table 10 Mechanical specifications
Parameter Nominal values Units
Outline dimensions (LxWxH) 57.0x24.0x2.1 mm3
Weight 4.3 g
The figure following shows nominal geometry of the WLAN6090SD card.
Figure 3 WLAN6090SD Geometry
SyChip Confidential Page 15 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
1.14 Pin configuration
The SD interface of the WLAN6060EB supports both the SD 4-bit mode, SD 1-bit mode, and the SPI
mode. The pin definitions for each mode are shown in the table followed.
Table 11 Pin definition in SDIO card7
PIN SD 4-bit mode SD 1-bit mode SPI mode
1 CD/DAT[3] Data line 3 N/C Not Used CS Card Select
2 CMD Command line CMD Co mmand line DI Data input
3 VSS1 Ground VSS1 Ground VSS1 Ground
4 VDD Supply voltage VDD Supply voltage VDD Supply voltage
5 CLK Clock CLK Clock SCLK Clock
6 VSS2 Ground VSS2 Ground VSS2 Ground
7 DAT[0] Data line 0 DATA Data line DO Data output
8 DAT[1] Data line 1 or
Interrupt (optional)
9 DAT[2] Data line 2 or Read
Wait (optional)
IRQ Interrupt IRQ Interrupt
RW Read Wait
(optional)
NC
Not Used
1.15 Bulk packaging
The WLAN6090SD cards are packaged in 50-piece partition boxes. A carton containing 20 boxes is
labeled for shipping (1,000 cards per carton). The detailed package for shipping is illustrated in the
following figure for reference.
Retail packages are also available upon request. A retail package will contain a single WLAN6090SD
card, the device driver, and the user manual in a CD.
7
SD Input/Output (SDIO) Card Specification 1.0.
SyChip Confidential Page 16 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
SyChip Confidential Page 17 of 19 SyChip_WLAN6090SD
2 Ordering Information
2.1 WLAN SDIO card naming convention
The WLAN SDIO card naming convention is shown below.
- __- __ -
WLAN6090SD
X
WLAN6090SD Data Sheet
01: Region 1(Channels 1-11)
02: Region 2 (Channels 1-13)
04: Region 4 (Channels 1-14)
BK: Bulk Packing (50 pcs/box)
Optional X digit to denote sample
devices
2.2 Sample orders
WLAN6090SD can be ordered as sample kits with part number
WLAN6090SDX
The sample kit includes a WLAN6090SDX card and a companion CD with device drivers and related
user documentation.
WLAN6090SDX sample cards are calibrated to the same specifications as defined in this document
except for the operating channel setting. All the samples are opened to operate in Channel 1-14 to
facilitate testing. Please observe the warnings below.
WARNING
THE SAMPLES ARE NOT FOR COMMERCIAL USE. THEY ARE FOR INTERNAL LAB
ENVIRONMENT ONLY. AS SUCH, THEY MAY OPERATE OVER THE COMPLETE 802.11b
SPECTRUM (i.e. CH. 1-14).
2.3 Production orders
Production order is in bulk packaging. The minimal order quantity (MOQ) is 1,000 cards.
Example:
WLAN6090SD-BK-02
SyChip Confidential Page 18 of 19 SyChip_WLAN6090SD
WLAN6090SD Data Sheet
This is a bulk production order of 1,000 pieces in one carton. The cards will be operating in Region 2
(most Europe countries, Korea, etc) with RF channels configured from CH 1~13.
3 Technical Support
SyChip, Inc
Parkway Centre II
2805 Dallas Parkway Suite 400
Plano, Tx 75093
USA
Tel: (972) 836-0010
Fax: (972) 633-0327
Email: support@sychip.com
SyChip Confidential Page 19 of 19 SyChip_WLAN6090SD
Loading...