Murata DMS-20PC-4/20S-C, DMS-20PC-4/20B-C, DMS-20PC-4/20P-C, DMS-20PC-4/20, DMS-BZL4-C User Manual

...

Download

Page 1

www.murata-ps.com

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

FEATURES



Industry's ﬁ rst loop-powered meter with a large, easy-to-read, LED display!



Self-powered, no external supply required



Unipolar, Bipolar and Positive Reading Models



Large, 0.37"/9.4mm digits



Excellent display intensity



High-quality, 20-turn, span (gain) and zero (offset) adjustments



DIP-switch selectable range and decimal points



Hundreds of input/readout combinations



Vibration-resistant package; Reliable screw-terminal input connections

SIMPLIFIED SCHEMATIC DIAGRAM

R3 R7

The DMS-20PC-4/20 Series are the world's ﬁ rst loop-powered digital panel meters with a large, easy-to-read, bright red, LED display. All operating power is derived directly from the loop current itself—no external power supply is required! The large,

0.37"/9.4mm digits exhibit uniform intensity over the entire 4-20mA operating range. Additionally, the total maximum loop voltage drop is only 5V! Users no longer have to settle for difﬁ cult-to-read LCD displays in loop-powered applications.

Both gain (span) and offset (zero) adjustments are performed with on-board, precision, 20-turn potentiometers. All decimal-point and range-change selections are made on a sixposition DIP switch featuring vibration-resistant, gold-plated contacts. Unlike competitive meters, there are no jumpers or solder gaps to open or close. Connections to the current loop are made via a reliable, two-position, screw-type terminal block.

The DMS-20PC-4/20's DIP switch and adjustment potentiometers accommodate hundreds of different input-current/output-reading combinations. This versatility practically eliminates the need to order more costly, long-lead-time, factory-customized "specials" in applications in which several different-range meters are required. An optional bezel assembly, featuring screw fasteners and a rubber seal, simpliﬁ es panel mounting and provides excellent resistance to environmental dust and moisture. All these outstanding features combine to make the DMS-20PC-4/20 Series the perfect meters for prototype and OEM 4-20mA current-loop instrumentation.

3½ DIGIT A/D CONVERTER

DATA

DP3DP2DP1

ZERO

ADJUST

BAND-GAP

REFERENCE

CIRCUIT

+5V –5V

DC/DC

For full details go to

www.murata-ps.com/rohs

CONVERTER

www.murata-ps.com/support

GAIN

ADJUST

12345

CURRENT TO

VOLTAGE

CONVERTER

DIP SWITCHES

TB1

+–

–+

LOOP INPUT

MPM_DMS20PC-4/20.D01 Page 1 of 6

Page 2

Performance/Functional Speciﬁ cations

Typical at TA = +25°C, unless otherwise noted.

Current Loop Input Min. Typ. Max. Units

Full Scale Input Range: ➀

Input Impedance: ➁

Voltage Drop ➁

Overcurrent Protection ➀

Performance

Sampling Rate 2.5 reading per second

Accuracy (1 minute warm-up): ±0.05%FS ±1 Count

Temperature Drift (0 to +60°C)

Display

Display Type and Size 3½ digit, 0.37"/9.4mm high red LED

Polarity Indication "–" for negative reading

Overrange Indication "–1____" for negative Vin

Physical/Environmental

Operating Temperature 0 – +60 °C

Storage Temperature –40 – +75 °C

Humidity (non-condensing) 0 – 95 %

Case Material Polycarbonate

Weight 0.6 ounces (17 grams)

➀ The DMS-20PC-4/20, using any of the DIP-switch settings described above, can

withstand overcurrents, including those resulting from accidental reverse-polarity connections, up to ±40mA without sustaining any damage.

➁ Because Murata Power Solutions' DMS-4/20 loop-powered meters employ active

circuitry to convert the loop current into a voltage, the meters' effective series impedance varies in a manner that maintains the loop voltage drop constant over the full 4-to-20mA current range. Listed impedance speciﬁ cation applies at 20mA.

➂ When looking up DIP-switch settings in the Tables and the desired display

readings can be achieved with either of two different settings, using the higher setting # will produce less sensitive offset (R3) and span (R7) adjustments. Please keep in mind that the DMS-20PC standard meter (from which the DMS20PC-4/20 is derived) has an accuracy speciﬁ cation of ±2 counts (max.). Thus, it may not always be possible to obtain the exact desired display reading.

+4 – +20 mA

– 250

– 4.5 5.0 Volts

––

– ±0.15 ±0.3 Cnts/°C

"1____" for positive Vin

±40

Ordering Information

DMS-20PC-4/20S-C Unipolar reading, loop-powered LED meter DMS-20PC-4/20B-C Bipolar reading, loop-powered LED meter DMS-20PC-4/20P-C Positive reading, loop-powered LED meter

DMS-BZL3-C Bezel assembly DMS-BZL4-C Bezel assembly with sealing gasket DMS-20-CP Panel cutout punch

A panel-mount retaining clip is supplied with each model.

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

OPERATING AND SETUP INSTRUCTIONS

DMS-20PC-4/20S (Unipolar Reading Model)

As shipped, the DMS-20PC-4/20S is factory calibrated to read "000"

for a 4mA input and "1000" for a 20mA input. The following worst-case

procedure assumes the DMS-20PC-4/20S is completely mis-adjusted,

i.e., both potentiometers and the DIP switches are randomly set. When

performing DIP-switch settings, be sure the DIP switch's small actuators

are ﬁ rmly engaged in their fully-ON or fully-OFF positions.

1. Set R7 (full scale span/gain adjust) and R3 (zero/offset adjust) fully

clockwise, roughly 22 turns, and place SW1-SW6 to OFF.

2. Select DIP switch setting #2.

3. Apply a precision 4mA input, with proper polarity, and adjust R3 until

the meter's display reads "000".

4. Apply a precision 20mA input and adjust R7 until the meter's display

reads "1000". Repeat steps 3 and 4 to make sure the adjustments do

not affect one another.

5. Select the appropriate decimal point by setting SW4, SW5 or SW6 to

ON (DP1, DP2 or DP3 respectively).

NOTE: If a display reading other than "000" to "1000" is desired,

refer to DIP–Switch Settings Table 1 for SW1–SW3 settings.

Table 1. DMS-20PC-4/20S (Unipolar Model) DIP-Switch Settings

Display Reading SW1 SW2 SW3

4mA 20mA

1. 000 to 1050-1999 Off Off Off

2. 000 to 650-1350 On Off Off

3. 000 to 450-800 Off On Off

4. 000 to 300-500 Off Off On

5. 000 to 200-300 On On On

Examples (DMS-20PC-4/20S-Unipolar Model)

1. Desired display readings are:

4mA ="0.00"

20mA = "6.00"

Use DIP-switch setting #3 in Table 1 and enable decimal point DP2 via

SW5. Apply 4mA and adjust R3 so the display reads "0.00". Apply

20mA and adjust R7 so the display reads "6.00".

2. Desired display readings are:

4mA = "000"

20mA = "800"

Use DIP-switch setting #2 in Table 1. Apply 4mA and adjust R3 so the

display reads "000". Apply 20mA and adjust R7 so the display reads

"800". For these display readings, no decimal points are used. Set

SW4, SW5 and SW6 to OFF.

123

www.murata-ps.com/support

MPM_DMS20PC-4/20.D01 Page 2 of 6

Page 3

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

3. Desired display readings are:

4mA = ".000"

12mA = ".250"

1234

This example is not as straightforward as the previous two. Notice that

12mA is exactly halfway between 4mA and 20mA. If we assume that

the input could go up to 20mA, the display reading would then be: 2

x .250 or ".500". From Table 1 we can now select DIP-switch setting

#4 and enable DP1 via SW4. Apply 4mA and adjust R3 so the display

reads ".000". Apply 12mA and adjust R7 so the display

reads ".250".

DMS–20PC–4/20B (Bipolar Reading Model)

The DMS-20PC-4/20B's zero-offset circuit differs from the unipolar 'S'

model described above in that with the 'B' model, a half-scale 12mA input

is normally set to display "000". Therefore, all of the of the DIP-switch

settings in Table 2 assume a reading of "000" is desired with a 12mA input.

Display readings other than those shown in Table 2 are possible, contact

Murata Power Solutions for more information.

When conﬁ guring the DMS-20PC-4/20B for the ﬁ rst time, or when select-

ing a new range, set both R3 and R7 fully clockwise (roughly 22 turns) to

their minimum offset/minimum-span positions, respectively. Then select

the desired readings from Table 2 and conﬁ gure DIP-switches SW1, SW2,

and SW3 accordingly.

The procedure below illustrates how to calibrate the DMS-20PC-4/20B

to its factory-calibrated readings of "–1000" with a 4mA input and "1000"

with a 20mA input. When performing DIP-switch settings, be sure the DIP-

switch's small actuators are ﬁ rmly engaged in their fully-ON or fully-OFF

positions.

1. Set both R3 and R7 fully clockwise.

2. Select DIP-switch setting #1 from Table 2.

3. Apply a precision 12mA input and adjust R3 until the meter's display

reads "000".

4. Apply a precision 20mA input and adjust R7 until the meter's display

reads "1000".

5. Apply a precision 4mA input and the display should read "–1000".

Repeat steps 3 and 4 to make sure the two adjustments did not affect

one another.

Table 2. DMS-20PC-4/20B (Bipolar Model) DIP-Switch Settings

Display Reading SW1 SW2 SW3

4mA 12mA 20mA

1. –600 to –1000 000 600 to 1000 Off Off Off

2. –350 to –650 000 350 to 650 On Off Off

3. –250 to –400 000 250 to 400 Off On Off

4. –150 to –250 000 150 to 250 Off Off On

5. –100 to –150 000 100 to 150 On On On

Examples (DMS-20PC-4/20B-Bipolar Model)

1. Desired display readings are:

4mA = "–1.00"

20mA = "1.00"

Use DIP-switch setting #5 in Table 2 and enable decimal point DP2 via

SW5. Apply 12mA and adjust R3 so the display reads "0.00". Apply

20mA and adjust R7 so the display reads "1.00". Apply 4mA and verify

that the display reads "–1.00", readjust R3 and R7 if necessary.

2. Desired display readings are:

4mA = "–450"

20mA = "450"

123

Use DIP-switch setting #2 in Table 2. Apply 12mA and adjust R3 so the

display reads "000". Apply 20mA and adjust R7 so the display reads

"450". Apply 4mA and verify that the display reads "–450". Repeat

adjustment procedure if necessary. For these display readings, no

decimal points are used. Set SW4, SW5 and SW6 to OFF.

3. Desired display readings are:

4mA = "–650"

20mA = "650"

123

Notice that these readings can be obtained using either DIP-switch

setting #1 or DIP-switch setting #2 in Table 2. In situations like this

where DIP-switch settings overlap, less-sensitive R3/R7 adjustments

can be achieved if the higher DIP-setting # is selected (setting #2 in

this example). Apply 12mA and adjust R3 so the display reads "000".

Apply 20mA and adjust R7 so the display reads "650". Apply 4mA and

verify that the display reads "–650". Repeat adjustment procedure if

necessary.

DMS-20PC-4/20P (Positive Reading Model)

The DMS-20PC-4/20P’s Zero-Offset circuit is optimized to produce posi-

tive readings at both 4mA and 20mA input levels. As shown in Table 3’s

ﬁ rst three columns, a 4mA input can be typically adjusted (using R3, Zero/

Offset Adjust) to display any positive reading between “000” and “800”.

The corresponding 20mA-input reading is then added to the 4mA offset

as a differential whose magnitude is varied by adjusting R7 (Gain/Span

Adjust).

The ‘Differential Range’ column in Table 3 lists the nominal differential

display-readings which can be obtained with R7 at, or very close to, its

full-clockwise, minimum span position. The Differential Range column can

be used as a guide when conﬁ guring the meter for the majority of user

applications. Higher differential ranges are obtainable; however, the use of

higher differential readings results in correspondingly-lower positive read-

ings with 4mA inputs, that is, R3’s clockwise adjustment-range is reduced.

Example #3 below illustrates this concept. Please contact Murata Power

Solutions if there is any doubt as to whether or not the DMS-20PC-4/20P

can be conﬁ gured for your display readings requirements.

The ﬁ rst step when conﬁ guring the DMS-20PC-4/20P for the ﬁ rst time, or

when selecting a new range, is to set R3 fully counterclockwise and R7

1234

www.murata-ps.com/support

MPM_DMS20PC-4/20.D01 Page 3 of 6

Page 4

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

fully clockwise (roughly 22 turns) to their minimum offset/minimum span

positions, respectively.

The next step is to calculate the required display differential-reading; this

is accomplished by subtracting the desired 4mA display reading from

the desired 20mA display reading, disregarding decimal points. Then,

using the calculated differential display-reading to select the appropriate

DIP-switch setting # from Table 3, conﬁ gure DIP-switches SW1, SW2, and

SW3 accordingly. Make certain that the DIP-switch’s small actuators are

ﬁ rmly engaged in their fully-ON or fully-OFF positions.

The procedure below describes how to calibrate the meter for an applica-

tion which the DMS-20PC-4/20P easily accommodates: displaying the

output of a 4-20mA transmitter, that is, “04.0” with a 4mA input and “20.0”

with a 20mA input.

1. Set R3 fully counterclockwise (minimum offset position) and R7 fully

clockwise (minimum differential span position), roughly 22 turns.

2. Subtract 040 from 200 to yield a differential value of 160; use this value

to select DIP-switch setting #5 in Table 3. Enable decimal point DP3 by

placing SW6 to the ON position.

3. Set the transmitter’s output to 4.0mA and carefully adjust R3 clockwise

until the meter’s display reads “000”.

4. Set the transmitter’s output to 20.0mA and adjust R7 counterclock-

wise until the meter’s display reads “16.0”.

5. Set the transmitter back to 4.0mA and slowly adjust R3 clockwise until

the display reads “04.0”. Reapply 20.0mA and the display should now

read “20.0”. Repeat steps 3, 4 and 5 to make sure the adjustments did

not affect one another.

Table 3. DMS-20PC-4/20P (Positive Reading Model) DIP-Switch Settings

Display Reading SW1 SW2 SW3

Differential Range 4mA Input 20mA Input

Table 4. Decimal Point Settings

SW4 SW5 SW6

DP1 DP2 DP3

Examples (DMS-20PC-4/20P-Positive Model)

1. Desired display readings are:

4mA = “650”

20mA = “950”

Use DIP-switch setting #4 in Table 3 since subtracting 650 from 950

yields a differential value of 300. Apply 4mA and adjust R3 until the

display reads “000”. Apply 20mA and adjust R7 until the display reads

“300” (the differential value previously calculated). Apply 4mA and

adjust R3 until the display reads “650”. Apply 20mA and verify that the

display reads “950”.

2. Desired display readings are:

4mA = “4.00”

20mA = “19.99”

This example illustrates the DMS-20PC-4/20P’s capability to display

higher differential readings than those indicated in Table 3. This

example also illustrates how the DMS-20PC-4/20P can be used to

display the output levels of a 4-20mA loop transmitter with higher preci-

sion (0.01mA versus 0.1mA) than described above.

Subtracting 400 from 1999 yields a differential of 1599, a value not

listed in Table 3. However, use DIP-switch setting #1 in Table 3 since

this setting has the highest overall offset/span adjustment capabilities.

Enable DP2 via SW5 then apply 4mA and adjust R3 so the display

reads “0.00”. Apply 20mA and adjust R7 so the display reads “15.99”.

Apply 4mA and adjust R3 until the display reads “4.00”. Apply 20mA

and check to see that the display reads “19.99” or just overranges

(“1—“). Repeat adjustment procedure if necessary.

1234

1. 800-1400 900 1700 Off Off Off

2. 500-800 850 1350 On Off Off

3. 350-500 800 1150 Off On Off

4. 250-350 750 1000 Off Off On

5. 150-250 750 900 On On On

www.murata-ps.com/support

MPM_DMS20PC-4/20.D01 Page 4 of 6

Page 5

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

TRANSDUCER

INPUT

85-264Vac

TRANSMITTER &

SIGNAL CONDITIONER

+24Vdc SUPPLY

–

+24V

PROGRAMMABLE

LOGIC CONTROLLER

4-20mA

➀

–

(TB1-1)

(TB1-2)

– –

➀ Shown for illustrative purposes only, may not be present in all applications

Figure 2. Typical DMS-20PC-4/20 Connection Diagram

DMS-20PC-4/20

Vsig

–

GAIN

A/D

ZERO

BEZEL INSTALLATION AND RECOMMENDED DRILL AND PANEL CUTOUT

0.093 (2.362) DIAMETER (4 REQUIRED) ONLY WHEN USING SUPPLIED BEZEL ASSEMBLY

1.07

(27.18)

FRONT VIEW

#2-56 INSERT

0.156 (3.96) DEEP

DMS-BZL4 BEZEL

1.826 (46.38)

BEZEL

0.187 (4.75)

1.280

(32.51)

PANEL

INTERNAL CORNER RADII:

0.032 (0.81) MAX.

1.336 (33.93)

1.626 (41.30)

RETAINING CLIP INSTALLATION

0.116 (2.95)

0.838

(21.29)

0.145 (3.68)

PANEL

www.murata-ps.com/support

MPM_DMS20PC-4/20.D01 Page 5 of 6

Page 6

MECHANICAL SPECIFICATIONS

MECHANICAL DIMENSIONS: Inches (mm)

TOLERANCES: 2 PL DEC ±0.02 (±0.51) 3 PL DEC ±0.010 (±0.254) WIRE SIZE: 18 to 26 AWG (Solid or stranded) STRIPPING LENGTH: 0.20" (5.08mm)

MADE IN USA

DMS-20PC-4/20 Series

Subminiature 4-20mA Loop-Powered

3½ Digit LED Process Monitors

0.95

0.040 (1.02)

DMS-20PC-4/20S

(24.1)

Zero/Offset

Adjust

Gain/Span

Adjust

Loop Input

Back View

DIP

Switches

1 2 3 4

1.30

(33.0)

1.38

(35.1)

DP1

(SW4)

DP2

(SW5)

Front View

0.80

(20.3)

0.88

(22.4)

DP3

(SW6)

Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansﬁ eld, MA 02048-1151 U.S.A.

ISO 9001 and 14001 REGISTERED

www.murata-ps.com/support

This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/

Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Speciﬁ cations are subject to change without notice. © 2015 Murata Power Solutions, Inc.

MPM_DMS20PC-4/20.D01 Page 6 of 6