mundoclima CL23410, CL23416 Installation Manual
MVD
Wall Mounted Split DC
Installation manual
www.mundoclima.comwww.mundoclima.com
CL23410 to CL23416
English
Installation manual
1
Wall mounted split
CONTENTS
PRECAUTIONS..........................................................................................1
INSTALLATION INFORMATION..................................................................2
ATTACHED FITTINGS...............................................................................3
INSPECTING AND HANDLING THE UNIT...................................................4
INDOOR UNIT INSTALLATION...................................................................4
REFRIGERANT PIPE INSTALLATION..........................................................6
WIRING CHART.........................................................................................7
TEST OPERATION....................................................................................10
PAGE
1. PRECAUTIONS
Be sure to be in conformity with the local, national and
international laws and regulations.
Read "PRECAUTIONS" carefully before installation.
The following precautions include important safty items.
Observe them and never forget.
Keep this manual with the owner's manual in a handy place
for future reference.
Installation must be performed in accordance with the
requirement of NEC and CEC by authorized personnel only.
The safty precautions listed here are divided into two categories. In
either case, important safty information is listed which must be read
carefully
.
ARNING
W
Failure to observe a warning may result in death.
CAUTION
Failure to observe a caution may result in injury or damage
to the equipment.
After completing the installation, make sure that the unit operates
properly during the start-up operation. Please instruct the customer
on how to operate the unit and keep it maintained.Also, inform
customers that they should store this installation manual along with
the owner's manual for future reference.
W
ARNING
Be sure only trained and qualified service personnel to
install, repair or service the equipment.
Improper installation, repair, and maintenance may result in
electric shocks, short-circuit, leaks, fire or other damage to
the equipment.
Install according to this installation instructions strictly.
If installation is defective, it will cause water leakage, electric
shocks, fire.
When installing the unit in a small room, take measures
against to keep refrigerant concentration from exceeding
allowable safety limits in the event of refrigerant leakage.
Contact the place of purchase for more information.
Excessive refrigerant in a closed ambient can lead to oxygen
deficiency
Use the attached accessories parts and specified parts
for installation.
otherwise, it will cause the set to fall, water leakage,
electrical shock fire.
Install at a strong and firm location which is able to
withstand the set' s weight.
If the strength is not enough or installation is not properly
done, the set will drop to cause injury.
The appliance must be installed 2.5m above floor.
The appliance shall not be installed in the laundry.
Before obtaining access to terminals, all supply circuits
must be disconnected.
The appliance must be positioned so that the plug is
accessible.
The enclosure of the appliance shall be marked by word,
or by symbols, with the direction of the fluid flow.
For electrical work, follow the local national wiring
standard, regulation and this installation instructions. An
independent circuit and single outlet must be used.
If electrical circuit capacity is not enough or defect in
electrical work, it will cause electrical shock fire.
Use the specified cable and connect tightly and clamp
the cable so that no external force will be acted on the
terminal.
If connection or fixing is not perfect, it will cause heat-up or
fire at the connection.
Wiring routing must be properly arranged so that control
board cover is fixed properly.
If control board cover is not fixed perfectly, it will cause
heat-up at connection point of terminal, fire or electrical
shock.
If the supply cord is damaged, it must be replaced by the
manufacture or its sevice agent or similarly qualifued
person in order to avoid a hazard.
An all-pole disconnection switch having a contact
separation of at least 3mm in all poles should be
connected in fixed wiring.
This appliance can be children aged from 8 yeas and
above and persons with reduced physical,sensory or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruct.
The A-weighted sound pressure level is below 70dB.
When carrying out piping connection, take care not to let
air substances go into refrigeration cycle.
Otherwise, it will cause lower capacity, abnormal high
pressure in the refrigeration cycle, explosion and injury.
Do not modify the length of the power supply cord or use
of extension cord, and do not share the single outlet with
other electrical appliances.
Otherwise, it will cause fire or electrical shock.
Carry out the specified installation work after taking into
account strong winds, typhoons or earthquakes.
Improper installation work may result in the equipment falling
and causing accidents.
.
Installation manual
2
Wall mounted split
If the refrigerant leaks during installation, ventilate the
area immediately.
Toxic gas may be produced if the refrigerant comes into the
place contacting with fire.
After completing the installation work, check that the
refrigerant does not leak.
Toxic gas may be produced if the refrigerant leaks into the
room and comes into contact with a source of fire, such as a
fan heater, stove or cooker.
The appliance shall be installed in accordance with
national wiring regulations.
The power cord type designation is H05RN-R/H07RN-F or
above.
CAUTION
Ground the air conditioner
Do not connect the ground wire to gas or water pipes,
lightning rod or a telephone ground wire.Incomplete
grounding may result in electric shocks.
Be sure to install an earth leakage breaker.
Failure to install an earth leakage breaker may result in
electric shocks.
Connect the outdoor unit wires , then connect the indoor
unit wires.
You are not allow to connect the air conditioner with the
power source until w(including
iring and piping the air conditioner is done.
.
There is strong electromagnetic wave existing.
There are inflammable materials or gas.
There is acid or alkaline liquid evaporating.
The appliance shall not be installed in the laundry
Avoid installing it in a narrow sapce which has a high
requirement to noise.
Other special conditions.
2. INST
T
first.
The air conditioner must be installed by qualified persons.
When installing the indoor unit or its tubing, please follow
this manual as strictly as possible.
If the air conditioner is installed on a metal part of the
building, it must be electrically insulated according to the
relevant standards to electrical appliances.
When all the installation work is finished, please turn on the
power only after a thorough check.
Regret for no further announcement if there is any change
of this manual caused by product improvement.
ALLATION INFORMATION
o install properly, please read this "installation manual" at
.
While following the instructions in this installation
manual, install drain piping in order to ensure proper
drainage and insulate piping in order to prevent
condensation.
Improper drain piping may result in water leakage and
property damage.
Install the indoor and outdoor units, power supply wiring
and connecting wires at least 1 meter away from
televisions or radios in order to prevent image
interference or noise.
Depending on the radio waves, a distance of 1 meter may not
be sufficient enough to eliminate the noise.
The appliance is not intended for use by young children
or infirm persons without supervision.
Young children should be supervised to ensure that they
do not play with the appliance.
Don't install the air conditioner in the following locations:
There is petrolatum existing.
There is salty air surrounding (near the coast).
There is caustic gas (the sulfide, for example) existing in
the air (near a hot spring).
The Volt vibrates violently (in the factories).
In buses or cabinets.
In kitchen where it is full of oil gas.
INST
ALLATION ORDER
Select the location;
Install the indoor unit;
Install the outdoor unit;
Install the connecting pipe ;
Connect the drain pipe;
Wiring;
est operation.
T
Installation manual
3
Wall mounted split
3. A
Please check whether the following fittings are of full scope. If there are some spare fittings , please restore them carefully.
TTACHED FITTINGS
1. Screw ST3.9x25 for installation board
2. Plastic expanded tube
rapping tape
3. W
4.Drain pipe
5. Wall conduit cover
6. Remote controller
7. Frame
SHAPENAME
QUANTITY
8
8
1
1
1
1
1
Secure the installation board
Hold the remote controller
FUNCTION
8. Mounting screw (ST2.9
9. Alkaline
10. Installation manual
1
1. Owner's manual
11.
12. Copper nut
dry batteries (AM4)
Network matching wire
10-C-H)
Cautions on remote controller installation:
Never throw or beat the controller
Before installation, operate the remote controller to determine its location in a
reception range.
.
2
2
1
1
1
Insulation Holder for remote controller
This manual
The indoor unit which at the terminal of
communication system should connect a
impedance between port P and port Q.
Connect piping
Mounting screw B
ST2.9x10-C-H
Keep the remote controller at least 1m apart from the nearest TV set or stereo
equipment. (it is necessary to prevent image disturbances or noise interferences.)
Do not install the remote controller in a place exposed to direct sunlight or close to a
heating source, such as a stove.
Note that the positive and negative poles are right positions when loading batteries.
This manual is subject to changes due to technological improvement without further
notices.
Remote
controller
Remote controller
holder
Fig.3-1
Loading...