MUND CLIMA MUP-07 CN, MUP-09 CN, MUP-12 CN, MUP-07 HN, MUP-16 C User Manual
...
®
MUND
CLIMA
Series 2000
Wall-mounted Split
COOL ONLY:
MUP-07 CN
MUP-09 CN
MUP-12 CN
MUP-16 CN
HEAT PUMP:
MUP-07 HN
MUP-09 HN
MUP-12 HN
MUP-16 HN
User´s manual
The instructions before use
WARNING
The power plug must be inserted tightly.
Otherwise, it can cause an
electric shock, overheating or
fire.
Don’t use longer power
lines and don’t share a same
socket with other electric appliances.
It can cause an electric shock
or fire.
Don’t pull out the power
plug during operating.
It can cause an electric shock
or fire.
Don’t operate the Air conditioner with wet hands.
It can cause an electric shock.
Never splice the power cord
or use an extended cord.
It can cause overheating or
fire.
Don’t insert your hands or
stick into the air intake or
outlet vents.
It can cause danger.
Don’t apply the cold wind
to the body for a longtime.
It cause the physical
condition deferioration and
health problems.
When having a burning
smell or smoke, please turn
off the power supply and
contact with the Service
center of MUNDOCLIMA.
–1–
Don’t attempt to repair the
air conditioner by yourself.
You may cause further malfunctions.
There must be electricity leakage protection switch of enough
power capacity and air switch in
the circuit.
Be sure to pull out the power
plug when not using the Air
Conditioner for a longtime.
When cleaning, it is necessary to stop driving and turn
off the power suply.
It occasionally cause the electric shock.
Don’t pull the power cord
to pull out the power plug.
It can cause fire.
Please note whether the installed stand is firm enough or
not.
It leads to the fall of the unit
causes the injury etc. occasionally.
Don’t place a space heater
near the air conditioner.
Air flow from the air conditioner can cause incomplete
combustion to the space heater.
Don’t step on the top of the
outdoor unit.
As falling off the outdoor unit
can be dangerous.
Keep combustible spray
away from the units.
It is likely to ignite.
Don’t block the air intake
or outlet vents of both the
outdoor and indoor units.
It can decrease the air conditioning capacity or cause a malfunction.
–2–
NAME AND FUNCTION OF EACH PART
Indoor unit
Outdoor unit
–3–
Remote control operation procedure
Name and Function-Remote control
Note:
•
Be sure that there are no obstructions.
•
The remote control signal can be received at a distance of up to about 10m.
•
Don’t drop or throw the remote control.
•
Don’t place the remote control in a location exposed to direct sunlight.
SWING button
When it is pressed, the
louvers start to rotate automatically and stop when
repressed.
TEMP.button
SET TEMP. increases 1°C by
pressing button once, and
decreases 1°C by pressing
button once.
At COOL mode operation,
SET TEMP. can be selected
from 16°C to 30.
At DRY mode operation, SET
TEMP. can be selected from
16°C to 30°C.
At HEAT mode operation,
SET TEMP. can be selected
from 16°C to 30°C.
FAN button
Presse this button to
change the fan speed of:
“ ” COOL mode
“ ” DRY mode
“ ” FAN mode
“ ” HEAT mode
MODE button
Press this button to
change the operation
mode in order of
1/0 button
Press this button to turn
on or turn off the unit
–4–
Name and Function-Remote control. (Remove the cover)
Note: This type of remote controller is a kind of new current controller. some
buttons of the controller which are not available to this Air conditioner
will not be described below.
Liquid crystal displayer
It shows all set contents.
AIR button
Press this button to change
the Air Refreshing mode in
order of
TIMER ON button
At stopping, press TIMER ON
button, set ON TIME in range of
0 to 24 hour to start the unit automatically.
SLEEP button
Press this button to set
SLEEP operation.
TIMER OFF button
At operating, press TIMER
OFF button, set OFF
TIME in range of 0 to 24
hour to stop the unit automatically.
–5–
COOL mode operation procedure
•
According to difference between room temp. and set temp., microcomputer can control
cooling on or not.
•
If room temp. is higher than set temp., compressor runs at COOL mode.
•
If room temp. is lower than set temp., compressor stops and only indoor fan motor
runs.
•
SET TEMP. should be in range of 16°C to 30°C.
4.Press FAN button, set
fan speed.
3.Press SWING button,
the louvers start to rotate automatically, and
stop when repress.
5.Press TEMP. button, set suitable SET
TEMP.
2.Press MODE button,
set operation
mode.
1.Plug in, press 1/0 button,then air
conditioner is turned on.
–6–
HEAT mode operation procedure
•
If room temp. is lower than set temp., compressor runs at HEAT mode;
•
If room temp. is higher than set temp., compressor and outdoor fan mortor stop, only
indoor fan mortor runs.
•
SET TEMP. should be in range of 16°C to 30°C.
¡æ
3.Press SWING button, the
louvers start to rotate automatically, and stop
when repress it.
4.Press FAN button, set
fan speed.
5.Press TEMP button, set
suitable SET TEMP.
1.Plug in, press 1/0
button,then air conditioner is turned on.
2.Press MODE button,
set operation
mode.
–7–
DRY mode operation procedure
•
If room temp. is lower than set temp., compressor ,outdoor and indoor fan mortor
stop. If room temp. is between ±2°C of set temp., air conditioner is drying. If room
temp. is higher than set temp., it’s at COOL mode.
•
SET TEMP. should be in range of 16°C to 30°C.
3.Press SWING button,
the louvers start to rotate automatically, and
stop when repress it.
4.Press TEMP. button,set
suitable SET TEMP.
2.Press MODE button, set
operation mode.
1.Plug in,press 1/0 button,then air
conditioner is turned on.
–8–
Loading...