Munchkin T50M, 140M, 199M, T80M, 80M Maintance Manual
HEAT TRANSFER PRODUCTS, INC.
120 BRALEY RD., E. FREETOWN, MA 02717
Installing, Operating & Maintaining
MUNCHKIN HIGH EFFICIENCY HEATER
with the “925” Controller
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
WARNING
If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
WARNING
This manual must only be used by a qualified heating installer / service
technician. Failure to comply could result in severe personal injury, death or
substantial property damage. It is also important to keep these Instructions
with the appliance.
MH27745
CONTROLS
USING THIS MANUAL
2
DANGER
Indicates a condition or hazard which
will
cause severe personal injury, death
or major property damage.
SPECIAL ATTENTION BOXES
Throughout this manual you will see these
special attention boxes similar to this one,
which are intended to supplement the
instructions and make special notice of
potential hazards. These categories mean, in
the judgement of Heat Transfer Products, Inc.:
WARNING
Indicates a condition or hazard which
may
cause severe personal injury,
death or major property damage.
WARNINGS
• THIS UNIT IS FOR CATEGORY IV VENTING - 2 PIPE ONLY. THIS IS A SEALED
COMBUSTION APPLIANCE.
• THIS HEATER INSTALLATION MUST CONFORM TO THE LATEST EDITION OF THE
“NATIONAL FUEL GAS CODE” ANSI Z223.1 NEPA 54 AND OR CAN/CGA B149
INSTALLATION CODES. STATE AND LOCAL CODES MIGHT ALSO APPLY TO
INSTALLATION.
• WHERE REQUIRED BY THE AUTHORITY HAVING JURISDICTION, THE
INSTALLATION MUST CONFORM TO THE STANDARDS FOR CONTROLS AND
SAFETY DEVICES FOR AUTOMATICALLY FIRED HEATERS, ANSI/ASME HEATER
AND PRESSURE VESSEL CODE, Section IV, ALONG WITH CSD1.
• THE HEATER, GAS PIPING, WATER PIPING, VENTING AND ELECTRICAL MUST BE
INSTALLED BY TRAINED & QUALIFIED PERSONNEL FAMILIAR WITH
INSTALLATION PRACTICES, LOCAL CODE, LICENSING REQUIREMENTS.
• IF THE INFORMATION IN THESE INSTRUCTIONS ARE NOT FOLLOWED EXACTLY,
A FIRE OR EXPLOSION MAY RESULT; CAUSING PROPERTY DAMAGE, PERSONAL
INJURY, OR DEATH.
• DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE;
• THE USE OF A LOW WATER CUT-OFF DEVICE MAY BE REQUIRED BY STATE OR
LOCAL CODES IF THE MUNCHKIN IS INSTALLED ABOVE RADIATION LEVELS.
CAUTION
Indicates a condition or hazard which
will or can cause minor personal injury
or property damage.
USING THIS MANUAL
TABLE OF CONTENTS
3
TABLE OF CONTENTS
PART 1 . . . . . . . . . . . . . . . . . . . . .4 thru 7
GENERAL INFORMATION
A How It Operates . . . . . . . . . . . . . . . . .4
B Munchkin Ratings and Dimensions . . .4
C Pre-installation Requirements . . . . . . .7
D Pressure Relief Valve . . . . . . . . . . . . . .7
PART 2 . . . . . . . . . . . . . . . . . . . . .8 thru 9
ELECTRICAL
A Electrical Connection . . . . . . . . . . . . . .8
PART 3 . . . . . . . . . . . . . . . . . . .10 thru 12
GAS CONNECTION
A Gas Connection . . . . . . . . . . . . . . . . .10
B Gas Piping . . . . . . . . . . . . . . . . . . . . .10
C Gas Table . . . . . . . . . . . . . . . . . . . . . .10
PART 4 . . . . . . . . . . . . . . . . . . .13 thru 21
VENTING
A Approved Venting Materials . . . . . . .13
B Venting the Munchkin in
2” or 3” Plastic Pipe . . . . . . . . . . . . .14
C Longer Vent Runs . . . . . . . . . . . . . . .16
D Heater Removal from a
Common Vent System . . . . . . . . . . .17
E Condensate Requirements . . . . . . . .21
PART 5 . . . . . . . . . . . . . . . . . . .22 thru 34
PIPING
A Hydronic piping with
Circulators or Zone Valves . . . . . . . .22
B Circulator Sizing . . . . . . . . . . . . . . . .23
C Fill and Purge Heating System . . . . .24
D Piping Illustrations . . . . . . . . . . . . . . .25
PART 6 . . . . . . . . . . . . . . . . . . .35 thru 37
START UP PROCEDURES
A Items to be checked before
lighting the Munchkin . . . . . . . . . . . .35
B Lighting Instructions . . . . . . . . . . . . .35
C Operating Instructions . . . . . . . . . . . .36
D Adjusting the Temperature
on the Munchkin Display . . . . . . . . . .36
E Status Menu . . . . . . . . . . . . . . . . . . .37
F To Turn Off Gas to Appliance . . . . . .37
PART 7 . . . . . . . . . . . . . . . . . . .38 thru 41
SERVICING
A Sequence of operation . . . . . . . . . . .38
B Munchkin Temporary
Fault Condition . . . . . . . . . . . . . . . . .38
C Munchkin Fault Requiring
Manual Reset . . . . . . . . . . . . . . . . . .39
PART 8 . . . . . . . . . . . . . . . . . . .42 thru 46
MAINTENANCE
A Maintenance Procedures . . . . . . . . . .42
B Before Each Heating Season . . . . . . .42
C Condensate Cleaning Instructions . . .42
D Combustion Chamber
Coil Cleaning Instructions . . . . . . . . .43
E Munchkin Controller . . . . . . . . . . . . .44
F Components Diagrams . . . . . . . .45–46
GENERAL INFORMATION
4
B. MUNCHKIN RATINGS AND DIMENSIONS
PERFORMANCE RATINGS
CONNECTION SIZES
PART 1. GENERAL INFORMATION
A. HOW IT OPERATES
When the room thermostat calls for heat, the Munchkin control board will start the circulator and start
to monitor the return temperature of the system before the heater will begin to heat the water. Once
the controller has sensed a drop in the return water temperature below the temperature set point
minus the differential set point, the heater will start to heat the water. This eliminates the Munchkin
starting every time the thermostat calls for heat. This feature keeps the system from short cycling.
Once the system has sensed the temperature difference, the Munchkin will activate the blower motor
for 5 seconds to pre-purge the system before starting the Munchkin
. The Munchkin controller will now
start to modulate the pre-mix burner based on analyzing the return temperature, supply water
temperature and the set point temperature. By compiling this information, the controller utilizes an
algorithm to fully adjust the firing rate while maintaining the desired output temperature. The pre-mix
burner fan has a direct drive current low-voltage motor with a pulse relay counting. This system allows
precise control over the fan speed and combustion air volumes. Coupled with the Honeywell gas valve
and the Venturi system which are set to provide a one-to-one ratio of precisely measured volumes of
fuel to air, an accurate and instant burner output is achieved. This keeps the Munchkin running at the
highest efficiency.
When the thermostat is satisfied, the Munchkin will then go through a 4 second post-purge cycle before
shutting off. Every Munchkin heater is equipped with a display which will read the outlet temperature of
the heater and then will illuminate a green light showing flame on. If a problem occurs, the front indicator
light will turn red and the display will read a fault code; see Part 7, Section B/C, pages 38 and 39.
ledoMnoitaludoMtupnIgnitaeHEODEUFAthgieWgnippihSRBI
M05T000,05ot000,81000,64ot000,61%29.sbl85000,04
M08T000,08ot000,91000,47ot000,71%29.sbl85000,46
M08000,08ot000,72000,47ot000,52%29.sbl57000,46
M041000,041ot000,64000,921ot000,34%29.sbl101000,211
M991000,991ot000,66000,381ot000,16%29.sbl111000,951
ledoM
M05TTPN"4/1"4/3"2
M08TTPN"4/1"4/3"2
M08TPN"4/1"4/3"3
M041TPN"4/1"4/3"3
M991TPN"4/1"4/3"3
nruteR/ylppuS
noitcennoCeziSnoitcennoCsaG.aiDtneV
GENERAL INFORMATION
5
Figure 1-1
(NOTE: The
Munchkin is rated
at zero clearance
to combustibles.)
Figure 1-3
T50M/T80M
80M/140M/199M T50M/T80M
DIMENSIONS
RECOMMENDED SERVICE CLEARANCES
Figure 1-2
GENERAL INFORMATION
6
DIMENSIONS
80M
140M/199M
Figure 1-4
Figure 1-5
7
GENERAL INFORMATION
C. PRE-INSTALLATION REQUIREMENTS
The Munchkin is designed for installation on non-rated flooring, in alcoves, basements, utility rooms,
and closet but never a bedroom closet. Choose a location for your Munchkin, centralized to the piping
system, along with consideration for Electrical (Part 2, Page 8), Gas Connection (Part 3, Page 10) and
Venting (Part 4, Page 13).
If the Munchkin is set up for liquefied petroleum (LP) gas, some geographic areas follow the Uniform
Mechanical Code, section 304.6, “Liquefied petroleum gas burning appliances shall not be installed in
a pit, basement or similar location where heavier-than-air gas might collect. Appliances so fueled, shall
not be installed in a below grade under-floor space or basement unless such location is provided with
an approved means for removal of unburned gas.”
WARNING
The Munchkin is certified as an indoor appliance. Do not install the Munchkin
outdoors or locate where it will be exposed to freezing temperature. This includes all
related piping and components. If the Munchkin is subjected to flood water or
submersed in water, the Munchkin must be replaced.
NOTICE
Service clearance of the Munchkin: See Section 1, Figures 1-1 and 1-2.
NOTICE
Condensation removal: This is a condensing high efficiency appliance, therefore
condensation removal must be addressed to avoid damage to surrounding area or
appliance. See Part (4) Section E for Condensate Requirements (pg. 21).
WARNING
D. PRESSURE RELIEF VALVE
A pressure relief valve is installed into the front right side manifold. We recommend a WATTS ¾"
M 335 MI valve or equivalent and meets the requirements of ANSI/ASME Heater and Pressure
Vessel Code, Section IV or CSA B51; Heater, Pressure Vessel and Piping Code as applicable for
heating heaters. A ¾" pipe must be directed to a floor drain or suitable location within 6" of a drain
or floor. Protect from freezing, do not plug or cap pressure relief valve. Serious explosion causing
property damage and or loss of life could result. Under no circumstances should the relief valve
be eliminated, capped or plugged.
8
ELECTRICAL
PART 2. ELECTRICAL
A. ELECTRICAL CONNECTION
The electrical connection for the Munchkin is on the left hand side of the unit. There is a ½” knockout
location for an electrical connection for both the incoming power and the central heating circulator
connection. All electrical wiring must be performed by a qualified licensed electrician in accordance
with National Electrical Code ANSI/NEPA to and/or the Canadian Electrical Code, Part 1 CSA C22.1, or
to the applicable codes and standards. For your convenience, we have labeled all the wires that need
to be connected to operate the Munchkin.
The electrical requirements are for standard 120 volts, 60 Hz 15 Amp service. This unit is wired with
#18 awg and fused for no more than 15 Amps.
There are two ground points in the electrical compartment that must be connected to the building
ground system. Connect the building ground to the green ground screw and the green ground wire
inside electrical box provided.
The Incoming Power Supply is connected to the Black (Hot) and the White (Neutral).The Munchkin
Control board is polarity sensitive. If the polarity is reversed, the Munchkin control will not sense a
flame and lock out the system. The Orange and Brown wire are provided to the supply of 120 volts to
the Central Heating Circulator. Connect the Orange (Hot) and the Brown (Neutral) directly to the Central
Heating Circulator.
Connect the gray wires to your heating thermostat (TT) connection. Your thermostat heat anticipator
setting is .056 amp.
CAUTION
Electrical wiring on the Incoming Power and Central Heating Circulator shall be
connected directly to the intended connection source and not be connected together
inside the electric box provided. An Electrical Short will result and the Control board
will have to be replaced! If Electrical Requirements of the Central Heating Circulator
exceeds 4 amps (or 3 amps on HA models only) please follow the wiring diagrams on
Page 9, Figures 2-1, 2-2 and 2-3.
DANGER
IT IS EXTREMELY IMPORTANT THAT THIS UNIT BE PROPERLY GROUNDED!
DANGER
IT IS VERY IMPORTANT THAT THE BUILDING GROUND IS INSPECTED BY A
QUALIFIED ELECTRICIAN PRIOR TO MAKING THIS CONNECTION!
DANGER
The Orange wire for the Central Heating Circulator is Switched Hot and must have a
wire nut if not connected to the Central Heating Circulator. Failure to follow this
instruction will result in a short, and the Control Board will have to be replaced.
9
ELECTRICAL
It is important that the electrical power is not turned on at this time. Double check all connections and then
turn the power on. The display that is provided with the Munchkin should now be reading the outlet
temperature. Note: see Part 6/Startup Procedure section in the manual to change the temperature setting
or run the heater.
NOTICE
Do not power zone valves directly from the heater transformer. Doing so will greatly
reduce the life of the transformer. Use a separate transformer sized to handle the total
electric load of all zone valves.
Figure 2-1: Connection Wiring Directly to
Central Heating Circulator
Figure 2-2: Connection Wiring without Wiring
Central Heating Circulator
Note to Electrical Contractor: The orange
wire is 120 Volt/4 Amp maximum for central
heating circulator only. Loads greater than 4
amps or 3 amps for HA models only will blow the
fuse on the board. The brown wire is the neutral wire for the central heating pump only.
Figure 2-3: For circulator amp loads greater
than 4 amps (3 amps for “HA” models) use the
wiring diagram shown at left. The brown and
orange wires will not be used in this
application.
5
T
1
2
3
6
4
T
1K1 1K2
BOILER
"TT"
GRAY
ZONE
CIRCULATOR
120 VOLT
L1 HOT (BLACK)
GRAY
BOILER
"TT"
THERMOSTAT
ZONE
R845A
SWITCHING
RELAY ZONE
1K1
L2 NEUTRAL
(WHITE)
DIAGRAM "A"
WIRING DIAGRAM CONNECTING TO CIRCULATOR
GREEN (GROUND)
WHITE (NEUTRAL)
BLACK
NORMALLY OPEN
THERMOSTAT
CONNECTION
GRAY
T
GRAY
T
BROWN (NEUTRAL)
ORANGE (HOT)
GREEN (GROUND)
(NEUTRAL)
ELECTRICAL
SWITCH JUNCTION BOX
120V 60 HZ
WHITE
(GROUND)
GREEN
BLACK
(HOT)
DIAGRAM "B"
WIRING DIAGRAM WITHOUT CONNECTION TO CIRCULATOR
IMPORTANT NOTE:
N
BE CERTAIN THAT THE ORANGE
WIRE IS SECURELY CAPED.
GREEN
ORANGE
NORMALLY OPEN
THERMOSTAT
CONNECTION
GRAY
T
GRAY
T
BROW
ORANGE (HOT)
BROWN (NEUTRAL)
SWITCH JUNCTION BOX
120V 60 HZ
FAILURE TO DO SO COULD
RESULT IN INJURY OR FIRE
AND COULD DAMAGE THE CONTROL.
WHITE
(NEUTRAL)
GREEN (GROUND)
GREEN
(GROUND)
ELECTRICAL
BLACK
(HOT)
GROUND
BUS
10
GAS CONNECTION
PART 3. GAS CONNECTION
A. GAS CONNECTION
The gas supply shall have a maximum inlet pressure of less
than 14" water column (350 mm), ½ pound pressure (3.4 kPa),
and a minimum of 7" water column. The entire piping system,
gas meter and regulator must be sized properly to prevent
pressure drop greater than 0.5" as stated in the National Fuel Gas
Code. This information is listed on the rating plate. It is very
important that you are connected to the type of gas as noted on the
rating plate. "LP" for liquefied petroleum, propane gas or, "Nat" natural or
city gas. All gas connections must be approved by the local gas supplier, or utility in addition to the
governing authority, prior to turning the gas supply on. The nipple provided is ½" and it is mandatory
that a ¾" to ½" reducing coupling (provided) is used, threaded into the branch of a ¾" tee, and a drip
leg fabricated, as per the National Fuel Gas code. You must ensure that the entire gas line to the
connection at the Munchkin is no smaller than ¾". Once all the inspections have been performed, the
piping must be leak tested. If the leak test requirement is a higher test pressure than the maximum inlet
pressure, you must isolate the Munchkin from the gas line. In order to do this, you must shut the gas
off using factory and field-installed gas cocks (following the lighting instructions in Part 6 Section B.)
This will prevent high pressure. Failure to do so may damage the gas valve. In the event the gas valve
is exposed to a pressure greater than ½ PSI, 14" water column, the gas valve must be replaced. Never
use an open flame (match, lighter, etc.) to check gas connections.
B. GAS PIPING
1. Run the gas supply line in accordance with all applicable codes.
2. Locate and install manual shutoff valves in accordance with state and local requirements.
C. GAS TABLE
Refer to Table (1) to size the supply piping to minimize pressure drop between meter or regulator
and unit.
Maximum Capacity of Pipe in Cubic Feet of Gas per Hour for Gas Pressures of 0.5 psi or Less and a
Pressure Drop of 0.3 Inch water Column
(TABLE 1) (Based on a 0.60 Specific Gravity Gas)
Nominal
Iron Pipe Internal Length of Pipe (Feet)
Size Diameter
(inches) (inches) 10 20 30 40 50 60 70 80 90 100 125 150 175 200.
3/4 .824 278 190 152 130 115 105 96 90 84 79 72 64 59 55} BTU'S
1 1.049 520 350 285 245 215 195 180 170 160 150 130 120 110 100} PER
1 1/4 1.380 1,050 730 590 500 440 400 370 350 320 305 275 250 225 210} HOUR
1 1/2 1.610 1,600 1,100 890 760 670 610 560 530 490 460 410 380 350 320} X 1,000
WARNING
Failure to follow all precautions could result in fire, explosion or death!
11
GAS CONNECTION
It is recommended that a soapy solution be used to detect leaks. Bubbles will appear on the pipe to
indicate a leak is present. The gas piping must be sized for the proper flow and length of pipe, to avoid
pressure drop. Both the gas meter and the gas regulator must be properly sized for the total gas load.
If you experience a pressure drop greater than 1" WC, the meter, regulator or gas line is undersized or
in need of service. You can attach a manometer to the incoming gas drip leg, by removing the cap and
installing the manometer. The gas pressure must remain between 7" and 14" during stand-by (static)
mode and while in operating (dynamic) mode. If an in-line regulator is used, it must be a minimum
of 10 feet from the Munchkin. It is very important that the gas line is properly purged by the gas
supplier or utility. Failure to properly purge the lines or improper line sizing, will result in ignition
failure. This problem is especially noticeable in NEW LP installations and also in empty tank situations.
This can also occur when a utility company shuts off service to an area to provide maintenance to their
lines. This gas valve must not be replaced with a conventional gas valve under any circumstances. As
an additional safety feature, this gas valve has a flanged connection to the Venturi and blower.
MUNCHKIN GAS VALVE
Fig. 3-1
DO NOT REMOVE THIS SCREW
OR ATTEMPT TO MAKE
ANY ADJUSTMENT TO THIS SCREW.
OUTLET PRESSURE TAP
INLET PRESSURE TAP
THROTTLE ADJUSTMENT SCREW.
NOTE: IF FOR ANY REASON THE SCREW IS
ADJUSTED, A "COMBUSTION ANALYZER"
MUST BE USED TO ENSURE SAFE AND
PROPER OPERATION. TURNING THE SCREW
CLOCKWISE DECREASES YOUR GAS FLOW
WHICH WILL LOWER THE CO/CO2 % LEVELS.
TURNING THE SCREW COUNTER-CLOCKWISE
INCREASES YOUR GAS FLOW WHICH WILL
RAISE THE CO/CO2 % LEVELS.
OUT
MIN
24 VOLT DC ELECTRICAL CONNECTION
V1
V2
1/2" NPT
GAS INLET
AIR INLET, KEEP FREE
OF DEBRIS
12
GENERAL INFORMATION
WARNING
Failure to follow all precautions could result in fire, explosion or death!
Fig. 3-3
Fig. 3-2
T50M/T80M GAS VALVE
COMBUSTION SETTINGS
HIGH FIRING RATES and LOW FIRING RATES ON ALL MODELS
Natural Gas Propane LP
high
Carbon CO ppm
Monoxide
Carbon CO
Dioxide
2%
low high
0-20 ppm
8-1/2 % - 9-1/2 %
80 ppm - 135 ppm
8-1/2 %- 9-1/2 %
low
0-20 ppm 80 -150 ppm
9-1/2 %- 10-1/2 % 9-1/2 %- 10-1/2 %
13
VENTING
PART 4. VENTING
A. APPROVED VENTING MATERIALS
Exhaust V
ent and Extensions
in Plastic 2", 3" and 4" Pipe Schedule 40 or 80.
1. Non Foam Core PVC Pipe
2. Non Foam Core CPVC Pipe
3. Non Foam Core ABS Pipe
Vent Piping must conform to following
1. PVC Non Foam Core Pipe (Polyvinyl Chloride) to ASTM D-1784 Class 12454-B, Formerly designated Type 1, Grade 1.
2. CPVC (Chlorinated Polyvinyl Chloride) Class 23447-B, Formerly designated Type IV, Grade 1 conforming to ASTM D-1784.
3. ABS (Acrylonitrile-Butadiene-Styrene) Class 3-2-2-2-2 conforming to ASTM D3965.
The Munchkin is a direct vent appliance. The Munchkin is listed as a Category
IV Condensing Appliance. (The Munchkin Venting is rated at Zero Clearance
to combustibles.)
Note: For Concrete construction or to meet certain fire codes, exhaust and inlet piping at the wall
penetration to the Munchkin must be CPVC Schedule 40 or 80 to meet local fire codes. The balance
from the penetrated wall to the outside, may be PVC Schedule 40 or 80.
Inlet Air V
ent
Use the same material as used for exhaust in either 2", 3" or 4" Plastic Pipe. Cellular Foam Core Pipe
may be used for the inlet only, NEVER ON EXHAUST PIPING!
DANGER
It is extremely important to follow these venting instructions carefully. Failure to do
so can cause severe personal injury, death or substantial property damage.
DANGER
Foam Core Pipe is not to be used in connecting the exhaust pipe.
WARNING
This vent system will operate with a positive pressure in the vent pipe. Do not
connect vent connectors serving appliances by natural draft into any portion of
mechanical draft systems operating under positive pressure.
14
VENTING
B. VENTING THE MUNCHKIN
The inlet pipe on the back of the cabinet should be 3" PVC schedule 40. It is very important that you
plan the location properly to eliminate long pipe runs and excessive fittings. Inlet pipe size must not
be reduced. Do not combine the inlet air with any other inlet pipe including an inlet to an additional
similar appliance. The joints must be properly cleaned, primed and cemented. The piping must also
be properly supported as per Local and National Standard Plumbing Codes. It is important that the
piping must be clean and free from burrs, debris, ragged ends and particles of PVC.
Exhaust piping should be sloped back to the connection on the Munchkin, at least ¼" per foot to
remove additional condensate that forms within the pipe. The total combined length of pipe (intake
piping plus exhaust piping added together) including elbow allowances intake and exhaust (each
elbow = 5' of pipe) should not exceed 85'. The combined vent length should not be less than a combined length of 6' plus two 90 degree elbows. Choose your vent termination locations carefully. You
must also make certain that exhaust gas does not re-circulate back into the intake pipe. You must
place them in an open area and follow the following guidelines.
1) Never vent into a walkway, patio area, alley or otherwise public area less than 7' from the
ground. (See the following detail references Fig. A.10.8 in the National Fuel Gas Code 2002
“Exit Terminals of Mechanical Draft and Direct-Venting Systems”.)
2) Never vent over or under a window or over a doorway where the exhaust plume or condensation liquid will cause obtrusive or dangerous conditions. (Or refer to National Fuel Gas
Code, CAN B149)
3) Never install a heat saver or similar product to capture waste heat from exhaust.
4) Always have a vent location at least 1' above maximum snow level.
5) Always have vent 1' above ground level, away from shrubs and bushes.
6) Follow local gas codes in your region or refer to National Fuel Gas Code, Can B149.
7) Always have at least 3' from an inside corner of outside walls.
8) Maintain at least 4' clearance to electric, gas meters, windows, exhaust fans, chimneys, inlets
or mechanical vents.
9) Very Important! The inlet air connection must be connected to outside air and should be
located no closer than 8" to the exhaust and no further than 36".
10) Always place screens in all openings in intake and exhaust to prevent foreign matter from
entering the Munchkin.
11) The vent intake and exhaust must be properly cleaned and glued for a pressure tight joint.
Several methods for venting the Munchkin can be found in Figures 4-1 thru 4-6, this section
pages 18 and 20. Use these layouts as guidelines: certain site conditions such as multiple
DANGER
It is extremely important to follow these venting instructions exactly. Failure to do so
can cause severe personal injury, death or substantial property damage.
NOTICE
The following are code restrictions for the location of the flue gas vent terminal.
Compliance to these requirements doesn’t insure a satisfactory installation; good
common sense must also be applied. It is important to make sure that exhaust gases
are not recirculated into the inlet air of the Munchkin.
15
roof lines/pitches may require venting modifications (consult factory). The air inlet must be a
minimum of 1' vertically above the maximum snow level. It is very important that there are
no other vents, chimneys or air inlets in any direction for at least 4'.
All venting must be properly supported. The Munchkin is not intended to support any venting
whatsoever. All piping, glue, solvents, cleaners, fittings and components, must conform to ASTM
(American Society for Testing and Materials), and ANSI (American National Standards Institute). It is
recommended that you use one of the optional vent kits specifically designed for Munchkin installations, available from Heat Transfer Products, Inc. (KGAVT0601CVT [3 in.], KGAVT0501CVT [2 in.] or
V1000). NOTE: When using the KGAVT601CVT KIT, REMOVE THE 2 SCREENS FROM THE PROVIDED INLET TEE AND INSTALL THEM IN THE INLET SOCKET AND OUTLET SOCKET (Y TEE CONNECTION) OF THE KIT PRIOR TO INSTALLING THE SCHEDULE 40 PIPE AND GLUING.
*Note: The V1000 when used for the T50 or T80 will require a transition piece from 2" to 3".
VENTING
CAUTION
Flue Gas will condense as it exits the vent termination. This condensate can freeze on
exterior building surfaces which may cause discoloration of these surfaces.
Consideration should be given to the plume of condensation that exits the exhaust
which may affect the cosmetic appearance of the building.
echanical
M
ent
raft v
d
al
in
rm
te
(see 10.8.1)*
raft
ical d
echan
M
al
in
12 in.m
vent term
(see 10.8.2)*
inimum
Less
than 10 ft.
3 ft.minimum
Forced air
inlet
rade
G
C
12 in.minimum
Direct vent terminal clearance
Minimum clearance, C
Input (Btu/hr)
10,000 or less
10,001 to 50,000
Over 50,000
(see 10.8.3)*
For SI units: 1 ft = 0.305 m; 1 in. = 25.4 mm;
1 Btu/hr = 0.293 W
Clearance (in.)
6
9
12
inim
4 ft.m
12 in.minimum
um
4 ft.
minimum
EXIT TERMINALS OF MECHANICAL DRAFT
AND DIRECT-VENT VENTING SYSTEM
* REFERENCE: THE NATIONAL FUEL GAS CODE
2002 EDITION
Loading...