QUICK GUIDE v2
Before starting DOWNLOAD the Smart Aligner App to your iPhone (iOS 7.0 or greater) or Android phone (4.1 or greater). For iOS go to the App Store and search “Smart
Aligner”. For Android go to the Google Play Store and search “smart aligner multiwave”. The iOS App and Android App have some differences as a result of different
operating systems. For Android devices with operating system less than 4.4 the Report will be in JPG format. For Android 4.4 the Report will be in PDF format (if high
resolution images are required select the JPEG option in Settings). This guide will show the user how to carry out an antenna alignment from start to finish for one
antenna and tool mounting configuration.
What’s in the case?
Smart Aligner Tool
Universal Mounting Bracket
Backpack
Smart Aligner Chargers
Attach the Universal Mounting Bracket to the antenna
Mounting Screw Knob
Mounting Dowel Pins
(under side)
Universal Mounting Bracket
Tether Line/Pin
Strap Release (orange button)
Ratcheting Handles
Dowel Pin Receptacles on
4 corners
Mounting Screw Knob Receptacle
Tether Line
(to mast or other solid location)
Tether Line Receptacle (from Tool)
Smart Aligner Tool (shown in folded position)
User Interface
Main Components
Optional mounting
adapters. Not included
with base system
Performing an Antenna Alignment
Ratchet Strap Fastening Pins
Ratchet Strap with hook
1. Tether the Universal Mounting
Bracket to a solid location.
2. Set the Universal
Mounting Bracket on the
backplane of the antenna
as shown. Keep the
Bracket in place by
holding on to the handle.
3. Depress the orange
Strap Release button with
your thumb and hold it
4. With your other hand
attach the hook of the
Ratchet Strap to the
appropriate Ratchet Strap
Fastening Pin
6. Squeeze the Ratcheting
Handles until the Bracket
is tight to the antenna
Attach the Smart Aligner Tool to the Universal Mounting Bracket
7. Tether the Smart Aligner Tool to
the Universal Mounting Bracket
8. Line up the Mounting Dowel
Pins (underside of Tool) to the
Dowel Pin Receptacles on the
Universal Mounting Bracket
9. Tighten the Mounting Screw
Knob on the Smart Aligner Tool
10. Rotate Small Arm clockwise till
you feel/hear it click in and engage
11. Rotate the Long Arm counter-
clockwise till you feel/hear it click
in and engage
12. Press the POWER
button on the User Interface and
wait for an azimuth solution
13. Turn over page for App instructions
(example is for iOS.)
Small Arm
Long Arm
1
2
3
NOTE: Universal Mounting
Bracket can be mounted on
either the right side (shown)
or left side of antenna
5. Release the orange
Strap Release button but
still hold the Bracket
NOTE: Smart Aligner Tool can
be mounted either front
(shown) , right or back
4 5
1
2
3,5
4
6
7
8,9
10
11 10
11
12
Connect by Wifi to the Smart Aligner Tool
6
1. You should already
have downloaded
the Smart Aligner
App to your mobile
device.
3. Tap the Smart Aligner App
7
Smart Aligner App
4. A splash screen will appear followed by the
Main Menu. Before proceeding check Settings
that Simulation mode is toggled to the off
position as shown
2. In the list of WiFi networks
you will see SmartAlignerSerialNumber.
Choose this Network and
Connect
5. To confirm that the Smart Aligner Tool and
App are connected tap Quick Measure. You
should see data updating in real time. If yes,
select <Back to return to the main menu
6. Tap Site Survey
7. Tap +
8. Enter Site name (e.g. “test”)
and tap OK
9. The site name and # of
antennas will be displayed
10. Tap the Site name (shown
“test”). You will now enter
the Antenna menu
11. Tap + for the Antenna
Details Screen
12. Enter the relevant data for
this antenna. The antenna is
identified by the Sector and
Position. Scroll down to view
all the set up data
13. You are now ready to
Align the antenna
14. Tap Align
8
Align and Verify
15. The Align Antenna real
time screen will be displayed.
16. Adjust the antenna to the
Target azimuth/tilt/roll to
within the desired/specified
error (tolerance).
17. Tap Verify
18. After verification the
following message will appear
19. Tap Accept
20. You will now be taken
back to the Antenna Details
Screen with the populated
Measurement Results. You
can take up to 4 Photos at this
point.
21.Tap Save
22.You will now be directed
to the Antenna list within the
site where you can create a
Report.
23. Tap Report
9
Reporting
24. Select the Antenna (s) you
want in the Report
25. Tap Report (All)
26. A PDF Report will now be
created and attached to your
email.
27. Email the Report
5
6
4
7,8,9,
10,11
12
13,14
15,16
17
18,19
22,
23
24
25 26
27
Loading...