Multi-Tech Systems MT5634ZBA-DID User Manual

MT5634ZBA-DID

Data/Fax/DID Modem

User Guide

Product Number S000234C Revision C MultiModemDID (MT5634ZBA-DID)

Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.

Record of Revisions

Revision Date Description

A 09/18/02 Supports V.92. Initial release of manual for publication on CD.

B 05/18/07 Revised tech support listing and warranty/repair descriptions.

C 01/02/08 Updated tech support contact listing.

05/15/09 Added a link to the Multi-Tech Web site for warranty information

Trademarks

MultiModemZBA, Multi-Tech, and the Multi-Tech logo are trademarks of Multi-Tech Systems, Inc. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. MNP is a trademark of Microcom,

Inc. Microsoft, Windows, Windows 95, Windows 98, Windows Me, Windows NT, Windows 2000, and Windows XP are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other brand and product names mentioned in this publication are trademarks or registered trademarks of their respective companies.

Warranty

For the Multi-Tech Warranty, see the Multi-Tech Web site at http://www.multitech.com

Patents

This device is covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560; 5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; D394,250; 5,724,356; 5,673,268; 5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; D374,222; 5,559,793; 5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; D361,764; D355,658; D355,653; D353,598; D353,144; 5,355,365; 5,309,562; 5,301,274. Other patents pending.

World Headquarters

Multi-Tech Systems, Inc. 2205 Woodale Drive Mounds View, MN 55112 Telephone (763) 785-3500 or (800) 328-9717 Fax (763) 785-9874

Technical Support Country By Email By Phone

Europe, Middle East, Africa: support@multitech.co.uk +(44) 118 959 7774 U.S., Canada, all others: support@multitech.com (800) 972-2439 or (763) 717-5863 Internet Address: http://www.multitech.com

MultiModemDID User Guide

Contents

Table of Contents

Chapter 1 - Introduction and Description......................................................................... 5

Introduction ........................................................................................................... 5

Features ............................................................................................................... 5

We Supply ............................................................................................................ 6

Safety ................................................................................................................... 6

Chapter 2 - Installation .................................................................................................... 7

Step 1: Assemble the Modem .............................................................................. 7

Step 2: Connect the Modem to Your System ....................................................... 7

Step 3: Install the Modem Driver .......................................................................... 8

Removing Your Old Modem from Windows.......................................................... 8

Chapter 3 – Operation ................................................................................................... 10

Front Panel of the MultiModemDID Modem ....................................................... 10

DID Operation..................................................................................................... 11

V.92 Operation ................................................................................................... 11

Connecting to the Internet .................................................................................. 12

Dial-Up Networking............................................................................................. 12

Chapter 4 - AT Commands, S -Registers, and Result Codes ....................................... 13

AT Commands.................................................................................................... 14

V.92 Commands ................................................................................................. 28

Other Commands ............................................................................................... 30

DID Commands .................................................................................................. 32

MT5634ZBA-DID Initialization Recommendations ............................................. 32

About the Busy-Out Features and Functions ..................................................... 33

S-Registers ......................................................................................................... 36

Result Codes ...................................................................................................... 39

Chapter 5 - Remote Configuration ................................................................................ 41

Basic Procedure ................................................................................................. 41

Setup .................................................................................................................. 41

MultiModemDID User Guide

Contents

Chapter 6 - Troubleshooting.......................................................................................... 43

None of the Indicators Light ............................................................................... 43

The Modem Does Not Respond to Commands.................................................. 43

The Modem Dials But Cannot Connect .............................................................. 44

The Modem Disconnects While Online ............................................................... 45

The Modem Cannot Connect When Answering ................................................. 45

The Modem Doesn’t Work with Caller ID............................................................ 45

Fax and Data Software Can’t Run at the Same Time ........................................ 45

DID Troubleshooting ........................................................................................... 46

Appendix A – Regulatory Compliance ........................................................................... 47

FCC Part 68 Telecom ......................................................................................... 47

FCC Part 15........................................................................................................ 48

Fax Branding Statement ..................................................................................... 48

Canadian Limitations Notice ............................................................................... 48

Industry Canada ................................................................................................. 48

Appendix B – Technical Specifications .......................................................................... 49

Appendix C - Upgrading the Modem’s Firmware........................................................... 52

Appendix D - Installing a Modem Under Linux .............................................................. 54

Introduction ......................................................................................................... 54

Standard Linux Serial Port Definitions ................................................................ 54

Installation .......................................................................................................... 54

Setup .................................................................................................................. 54

Index .................................................................................................... 54

MultiModemDID User Guide

Chapter 1 - Introduction and Description

Welcome to the world of data communications. You have acquired one of the finest intelligent data and fax modems available today from one of America’s oldest and most respected modem manufacturers: Multi-Tech Systems, Inc. This User Guide will help you install, configure, test, and use your modem.

Introduction

The MultiModemDID combines Direct Inward Dial (DID) with Super G3 V.34/33.6K bps fax and V.92 data modes of operation. Direct Inward Dial allows the user to use a block of telephone numbers larger than the number of physical telephone lines for direct dialing to extensions. When combining DID with inbound fax calls to a fax server, each user on the fax server can have faxes automatically routed to them at their client computer desktop.

DID fax routing assigns a unique fax number for every network user or network device (such as a printer). Senders simply dial a typical telephone number - no special procedures are required. The fax server automatically delivers the incoming fax to the user over the local area network.

Users get improved efficiency and security, since their faxes are delivered by the network fax server to the client desktop as soon as they are received. Time-wasting trips to the fax machine are eliminated and employees are more productive. In addition, DID offers a higher degree of security for both the sender and the recipient since faxes are not left unattended at a central fax machine.

The MT5634ZBA-DID utilizes Super G3 V.34 fax speeds of 33.6K bps. Now, computer-based fax servers can achieve the Super G3 speeds found in dedicated fax machines. The MT5634ZBA-DID also supports T.31 Annex B and T.32 Annex C, which allows the higher V.34 speeds to operate with Class 1.0 and Class 2.1 code sets. In addition, “on-the-fly” two-dimensional fax data compression plus support for error correction mode (ECM) increase the performance of the MT5634ZBA-DID to levels previously only found in expensive fax boards and dedicated fax machines.

To implement DID fax routing you must purchase fax server application software that supports Multi-Tech DID commands and DID routing, and obtain an analog DID trunk line which supports the inbound fax calls and a regular loop-start line for outbound fax transmission.

Features

· One Direct Inward Dial (DID) port

· Super G3 V.34/33.6K bps fax communication

· T.31 Annex B Class 1.0 and T.32 Annex C Class 2.1 fax commands

· Error Correction Mode (ECM) provides fast and reliable fax transmissions

· Supports Wink-start, Immediate-start and Delay dial service types

· V.92/56K data mode

· V.44 compression improves data throughput rates

· V.42 error correction

· Flash memory for easy updates

• Plug and Play operation.

• Interactive automatic dialing and command mode configuration.

• In standard mode, you can store up to four command lines or telephone numbers of up to 40

characters each in the modems’ nonvolatile memory.

• Pulse- or tone-dials and recognizes dial tones and busy signals for reliable call-progress detection.

• Detects AT&T calling card tones.

• Caller ID.

• Remote configuration.

• Incorporates self-resetting lightning protection.

MultiModemDID User Guide

Chapter 1 - Introduction and Description

We Supply

• An MT5634ZBA-DID modem

• A set of four self-adhesive plastic feet

• A power supply

• A 9-pin to 9-pin serial cable

• Two RJ-11 telephone cables

• A printed Quick Start Guide

• A CD containing modem drivers, a User Guide, and Adobe Acrobat Reader.

You Supply

• A computer with an available serial port

• A nearby AC power outlet

• A nearby phone line jack

• A nearby analog DID trunk line with a block of associated DID telephone numbers

Safety

1. Use this product only with UL and cUL listed computers.

2. To reduce the risk of fire, use only 26 AWG (.41mm) or larger telephone wiring.

3. Never install telephone wiring during a lightning storm.

4. Never install a telephone jack in wet locations unless the jack is specifically designed for wet locations.

5. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

6. Use caution when installing or modifying telephone lines.

7. Avoid using a telephone during an electrical storm. There is a risk of electrical shock from lightning.

8. Do not use a telephone in the vicinity of a gas leak.

MultiModemDID User Guide

Chapter 2 - Installation

Step 1: Assemble the Modem

The only assembly required is to mount the feet on the bottom of the modem. Simply peel the four selfadhesive plastic feet off the backing strip and press them into the recesses on the bottom of the modem.

Step 2: Connect the Modem to Your System

Turn off your computer. Place the modem in a convenient location, and then connect it to your computer’s serial port, the phone line, AC power, DID line, and your phone.

Connect the Modem to Your PC

Plug one end of the serial cable into the connector on the modem, and plug the other end into a serial port on your computer, such as COM1 or COM2.

Connect the Modem to the Telephone Line

Plug one end of the phone cable into the modem’s LINE jack and the other end into a phone wall jack. The phone cable is included with your modem.

Note: The LINE jack is not interchangeable with the PHONE jack. Do not plug the phone into the LINE jack or the line cable into the PHONE jack.

MultiModemDID User Guide

(Optional) Connect the Modem to the Phone

For voice-only calls, plug a phone into the modem’s PHONE jack.

Connect the Modem to the AC Power Outlet

Make sure the power is switch is OFF. Plug the DC power transformer into a power outlet or power strip. Plug the other end into the PWR jack on the modem. The DC power transformer is included with your modem.

CAUTION: Use only the DC power transformer supplied with the modem. Use of any other

transformer voids the warranty and can damage the modem.

Connect the Modem to the DID Line

Plug one end of the phone cable into the modem’s DID jack and the other end into an analog DID trunk line jack. The DID Line cable is included with your modem.

CAUTION: The DID Line cable has a 4-pos RJ11 on one side and a 6-pos on the other. Never plug

the DID connector into a standard POTS Line. This may damage the modem or the central office equipment. Use only an analog DID Line.

Power-on Test

Test the modem by turning it on (an on-off switch is located on the side panel). When you apply power, the modem performs a diagnostic self-test. The 56 indicator lights, and if a terminal program is running, the TR indicator also lights. If this does not happen, check that the power switch is on, the power supply is solidly connected, and the AC outlet is live. If these measures do not work, see the

Troubleshooting

chapter.

Chapter 2 - Installation

Step 3: Install the Modem Driver

1. Make sure your modem is connected properly, and then turn on your computer. Windows should detect your new modem and open the Install New Modem wizard.

Note: If Windows cannot find a modem, your modem may be turned off, it may be plugged into the

wrong connector on your computer, or the serial cable may be faulty. See “None of the LEDs Light When the Modem Is Turned On” and “The Modem Does Not Respond to Commands” in the “Troubleshooting” chapter in the complete User Guide.

2. Insert the MT5634ZBA-DID CD into your CD-ROM drive, and then click OK.

3. Windows installs the modem driver.

4. Click Finish to exit

Removing Your Old Modem from Windows

When your new modem replaces another modem, the old modem installation remains in Windows after you install the new modem, and the old modem is still selected in HyperTerminal and other Windows applications. Although you can change the application connection descriptions one at a time, it is easier to force Windows applications to use the new modem by removing the old modem from Windows.

MultiModemDID User Guide

Chapter 2 - Installation

From Windows 2000, XP

1. Click Start | Settings | Control Panel.

2. Double-click the Phone and Modems icon and click on the Modems tab.

3. In the list box, select the old modem.

4. Click Remove, then click Close.

5. The next time you dial a HyperTerminal connection, it will select your new modem and ask you to confirm the selection.

From Windows 98, Me

1. Click Start | Settings | Control Panel.

2. Double-click the Modems icon to open the Modems Properties sheet.

3. In the list box, select the old modem.

4. Click Remove, then click Close.

5. The next time you dial a HyperTerminal connection, it will select your new modem and ask you to confirm the selection.

MultiModemDID User Guide

Chapter 3 - Operation

Chapter 3 – Operation

Front Panel of the MultiModemDID Modem

The MT5634ZBA-DID modem has 10 LED indicators on the front panel that provide information about how your modem is operating: status, configuration and activity.

Transmit Data - The TD LED flashes when the modem is transmitting data to another modem.

Receive Data - The RD LED flashes when the modem is receiving data from another modem.

Carrier Detect - The CD LED lights when the modem detects a valid carrier signal from another

modem. It is on when the modem is communicating with the other modem and off when the link is broken.

56 - The 56 LED is a 56K mode indicator. It lights whenever the modem is set for or connects

using the V.90 or V.92 protocols.

33 - The 33 LED is a V.34 mode indicator. It lights whenever the modem connects using the V.34

protocol.

Off-Hook - The OH LED lights when the modem is off-hook, which occurs when the modem is

dialing, online, or answering a call. The LED flashes when the modem pulse-dials.

Terminal Ready - The TR LED lights when a communications program is using the modem. It

means the modem is ready for an outgoing or incoming call. It goes off when the communications program disconnects the serial port. When it goes off, a connected modem will also disconnect.

Error Correction (V.42) - The EC LED lights continuously when the modem is in V.42 error

correction mode, and it flashes when compression is achieved.

Fax - The FX LED lights when the modem is in fax mode.

DID - The DID LED lights when there is an incoming call on the DID line.

MultiModemDID User Guide

Chapter 3 - Operation

DID Operation

Direct Inward Dialing (DID) uses an analog trunk line to route several phone numbers to one line. The MT5634ZBA-DID modem has four ports, an RS232 serial port, two RJ11 ports for connection to a POTS line and an auxillary phone, and a 4 position RJ12 for connection to the DID analog trunk.

Note: The DID and POTS ports cannot operate simultaneously.

On a DID line the roles of the central office and the DID modem are somewhat reversed. The DID modem must provide a DC voltage, around 48V, to the line. When there is an incoming call, the central office will complete a loop and draw current from the DID modem.

On a standard POTS line, the central office provides the DC voltage and the user will close the loop by lifting the handset of a phone or making a call with a standard modem.

There are two critical points about the DC voltage:

1. The central office is sensitive to the DC polarity. TiP (positive) and riNg (Negative) must be

connected to the line from the central office with the proper polarity. If not, callers will receive an immediate busy signal or may be allowed to make a short connection but become unexpectedly disconnected after a short time.

2. The DC voltage should be applied by the modem at all times, even when not in use. Occasionally,

the central office will check the line; and, if a voltage is not sensed, the line will be put out of service. A call to the phone company will be required to get the line back in service.

The DID modem may use line reversals to signal the central office to send digit information or open the channel to the calling party depending on the start protocol of the DID line. The central office will forward several of the last digits of the incoming call to the DID modem through one of three formats, DTMF, MF, or pulse signaling.

V.92 Operation

Because the V.92 protocol is new and still largely unsupported by central servers, some features are disabled by default in the initial release of the MT5634ZBA-DID modem. This section describes the status of the V.92 features in the initial release. Please note that the V.92 special features require connection to a V.92-capable server.

• General. The V.92 protocol is enabled by default. If the MultiModemZBA-DID detects another

V.92 modem during the handshake phase, they will connect in V.92 mode; otherwise, they will connect in V.90 mode or the highest mutually acceptable mode. The AT command that controls this is +MS=.

• Commands. AT commands specific to the V.92 protocol and the new V.44 compression protocol

begin with the plus character (+). These commands are in this manual. Also, the S109 register has been modified to support V.92.

• PCM Upstream. PCM Upstream is disabled by default. To upload files at speeds above 33.6

kbps, you must enable PCM Upstream using the command +PIG=1. Please note that this requires connection to a V.92-capable server. Also, please note that since upload speeds are affected by line conditions, meeting the previous requirements cannot guarantee speeds above 33.6 kbps.

• Quick Connect. Quick Connect, which shortens the handshake time with another V.92 modem, is

disabled by default. To enable it, use the command +PQC=0. Quick Connect speeds connect times by skipping the line test during the handshake and using the configuration from the last data connection. Quick Connect works best when line conditions are consistent from call to call. If line conditions are variable, enabling Quick Connect can actually increase the connect time slightly.

• Modem on Hold (is not available at this time).

MultiModemDID User Guide

Chapter 3 - Operation

Connecting to the Internet

Your Multi-Tech modem is your gateway to the Internet and the World Wide Web. To access the Internet and Web via your modem, you must establish a dial-up account with an Internet service provider (ISP). To locate an ISP near you, look in a local directory or computer publication. Your ISP should provide you with the following information:

• User name (also called user ID)

• Password

• Access number (the number you call to connect to the server)

• Host name and/or domain name

• Domain Name Server (DNS) server address

If, besides the Web, you use the Internet for e-mail and newsgroups, your ISP should also provide you with the following information:

• E-mail or POP mail address

• POP server address

• Mail or SMTP address

• News or NNT server address

Dial-Up Networking

Before you can connect to the Internet, you must set up a remote-node client program on your computer. The Windows version is called Dial-Up Networking. Dial-Up Networking establishes your connection to the ISP’s server, which is the shared computer that manages calls from clients (your computer) to the Internet. Most, if not all, Windows browsers start Dial-Up Networking automatically when you open them.

For instructions on how to set up Dial-Up Networking, consult your ISP or your operating system’s online help or printed documentation. Many ISPs include, as part of their service, a program that will install and configure Dial-Up Networking automatically for you.

MultiModemDID User Guide

Chapter 4 - AT Commands, S-Registers, Result Codes

Chapter 4 - AT Commands, S -Registers,

and Result Codes

AT commands are used to control the operation of your modem. They are so called because each command must be preceded by the characters AT to get the ATtention of the modem.

AT commands can be issued only when the modem is in command mode or online command mode. The modem is in

mode

whenever it is connected to another modem and ready to exchange data. is a temporary state in which you can issue commands to the modem while connected to another modem. To put the modem into online command mode from data mode, you must issue an

sequence

the modem. To return to data mode from online command mode, you must issue the command ATO.

To send AT commands to the modem you must use a communications program, such as HyperTerminal or the PhoneTools communications program included with your modem. You can issue commands to the modem either directly, by typing them in the terminal window of the communications program, or indirectly, by configuring the operating system or communications program to send the commands automatically. Fortunately, communications programs make daily operation of modems effortless by hiding the commands from the user. Most users, therefore, need to use AT commands only when reconfiguring the modem, e.g., to turn autoanswer on or off.

The format for entering an AT command is ATXn, where X is the command and n is the value for the command, sometimes called the command you can omit it from the command; thus, AT&W is equivalent to AT&W0. Most commands have a value, which is the value that is set at the factory. The default values are shown in the “AT Commands” section, which begins on the next page.

You must press ENTER to send the command to the modem. Any time the modem receives a command, it sends a response known as a

CONNECT

For a table of valid result codes, see “Result Codes” at the end of this chapter.

You can issue several commands in one line, in what is called a command begins with AT and ends when you press ENTER. Spaces to separate the commands are optional; they are ignored by the command interpreter. The most familiar command string is the which is used to configure the modem when it is turned on or reset, or when your communications software calls another modem.

command mode

(+++) followed immediately by the AT characters and the command, e.g., +++ATH to hang up

messages that the modem sends to the computer when it is connecting to another modem.

whenever it is not connected to another modem. The modem is in

Online command mode

escape

result code

parameter

. The most common result codes are OK,

. The value is always a number. If the value is zero,

ERROR

string

. The command string

initialization string

, and the

data

default

MultiModemDID User Guide

AT Commands

Command: AT Attention Code Values: n/a Description: The attention code precedes all command lines except A/ and

Chapter 4 - AT Commands, S-Registers, Result Codes

the escape sequence.

Command: E

NTER Key

Values: n/a Description: Press the E

NTER or RETURN key to execute most commands.

Command: A Answer Values: n/a

Description: Answers an incoming call before the final ring.

Command: A/ Repeat Last Command Values: n/a Description: Repeats the last command string. Do not precede this

Command: B Values:

command with AT. Do not press E

Communication Standard Setting

= 0–3, 15, 16

NTER to execute.

Default: 1 and 16 Description: B0 Select ITU-T V.22 mode when modem is at 1200 bps.

B1 Select Bell 212A when modem is at 1200 bps. B2 Deselect V.23 reverse channel (same as B3). B3 Deselect V.23 reverse channel (same as B2). B15 Select V.21 when the modem is at 300 bps. B16 Select Bell 103J when the modem is at 300 bps.

Command: D Values:

Dial

= dial string (phone number and dial modifiers) Default: none Description: Dial telephone number s, where s may up to 40 characters long

and include the 0–9, *, #, A, B, C, and D characters, and the L, P, T, W, S, comma (,), semicolon (;), !, @, ^ and $ dial string modifiers.

Dial string modifiers:

L Redial last number. (Must be placed immediately after ATD.) P Select pulse-dialing until a T is encountered. Affects current

and subsequent dialing.

T Select tone-dialing until a P is encountered. Affects current

and subsequent dialing.

W Wait for a new dial tone before continuing to dial. (X2, X4,

X5, X6, or X7 must be selected.) , Pause during dialing for time set in register S8. ; Return to command mode after dialing. Place at end of dial

string. ! Hook flash. Causes the modem to go on-hook for one-half

second, then off-hook again.

MultiModemDID User Guide

Chapter 4 - AT Commands, S-Registers, Result Codes

@ Wait for quiet answer. Causes modem to wait for a ring

back, then 5 seconds of silence, before processing next

part of command. If silence is not detected, the modem

returns a NO ANSWER code.

^ Disable data calling tone transmission. $ Detect AT&T call card “bong” tone. The character should

follow the phone number and precede the user’s call card

number: ATDT1028806127853500

$123456789.

Command: DS= Values: Default: none Description: Dials a number previously stored in directory number y by the

Command: E Values: Default: 1 Description: E0 Does not echo keyboard input to the terminal.

Command: F Values: Default: 1 Description: F0 Enables online data character echo. (Not supported.)

Command: H Values: Default: 0 Description: H0 Goes on-hook (hangs up).

Dial Stored Telephone Number

= 0, 1, 2

&Zn=x

Echo Command Mode Characters

E1 Does echo keyboard input to the terminal.

Echo Online Data Characters

n =

F1 Disables online data character echo (included for backward

compatibility with some software).

Hook Control

H1 Goes off-hook (makes the phone line busy).

command. Example: ATDS=3.

= 0 or 1

0, 1

= 0 or 1

Command: I Values: Default: None Description: I0 Displays default speed and controller firmware version.

Information Request

= 0–5, 9, 11

I1 Calculates and displays ROM checksum (e.g., I2 Checks ROM and verifies the checksum, displaying

ROR

. I3 Displays default speed and controller firmware version. I4 Displays firmware version for data pump (e.g., 17). I5 Displays the board ID: software version, hardware version, and

the country ID in hexadecimal format (e.g., I9 Displays the country code in decimal format (e.g., I11 Displays diagnostic information for the last modem connection,

such as DSP and firmware version, link type, line speed, serial

speed, type of error correction/data compression, number of

past retrains, etc.

B399

s0503a01V, 0, 34

ER-

MultiModemDID User Guide

Chapter 4 - AT Commands, S-Registers, Result Codes

Command: M Values: Default: 1 Description: M0 Speaker always off.

Command: N Values: Default: 1 Description: N0 Modem performs handshake only at communication standard

Command: O Values: 0, 1, 3 Default: None Description: O0 Exits online command mode and returns to data mode (see

Monitor Speaker Mode

= 0, 1, 2, or 3

M1 Speaker on until carrier signal detected. M2 Speaker always on when modem is off-hook. M3 Speaker on until carrier is detected, except while dialing.

Modulation Handshake

= 0 or 1

specified by S37 and the B command. N1 Modem begins handshake at communication standard

specified by S37 and the B command. During handshake,

fallback to a lower speed can occur.

Return Online to Data Mode

+++AT<CR> escape sequence ).

O1 Issues a retrain and returns to online data mode. O3 Issues a rate renegotiation and returns to data mode.

Command: P Pulse Dialing Values: P, T Default: T Description: Configures the modem for pulse (non-touch-tone) dialing.

Dialed digits are pulsed until a T command or dial modifier is

received.

Command: Q Values: Default: 0 Description: Q0 Enables result codes.

Command: Sr=nSet Register Value Values: Default: None Description: Sets the value of register Sr to the value of n, where n is

Command: Sr? Read Register Value Values: Default: None Description: Reads the value of register Sr and displays it in 3-digit decimal

Result Codes Enable/Disable

= 0, 1

Q1 Disables result codes.

= S-register number; n varies

entered in decimal format. Example: S0=1.

= S-register number

form. For example, S2? gives the response

043

MultiModemDID User Guide

Command: T Tone Dialing Values: P, T Default: T Description: Configures the modem for DTMF (touch-tone) dialing. Dialed

Chapter 4 - AT Commands, S-Registers, Result Codes

digits are tone dialed until a P command or dial modifier is

received.

Command: V Values: Default: 1 Description: V0 Displays result codes as digits (terse response).

Command: W Values: Default: 2 Description: W0

Command: X Values: Default: 4 Description: X0 Basic result codes (

Result Code Format

= 0 or 1

V1 Displays result codes as words (verbose response).

Result Code Options

= 0, 1, 2

CONNECT

protocol result codes. W1

CONNECT

protocol result codes. W2

CONNECT

result codes.

Result Code Selection

= 0–7

tone or busy signal. X1 Extended result codes (

not look for dial tone or busy signal. X2 Extended result codes with

busy signal. X3 Extended result codes with X4 Extended result codes with X5 Extended result codes with X6 Extended result codes with X7 Basic result codes with

result code reports serial port speed, disables

result code reports serial port speed, enables

result code reports line speed, enables protocol

e.g., CONNECT

); does not look for dial

e.g., CONNECT 46000 V42bis

NO DIALTONE

BUSY

; does not look for dial tone.

NO DIALTONE NO DIALTONE NO DIALTONE

NO DIALTONE

; does not look for

and and and

and

BUSY

BUSY BUSY BUSY

); does

. . .

Command: Z Values: Default: None Description: Z0 Resets modem to profile saved by the last &W command.

Command: &CnData Carrier Detect (DCD) Control Values: Default: 1 Description: &C0 Forces the DCD circuit to be always high.

Modem Reset

= 0 or 1

Z1 Same as Z0.

= 0, 1, or 2

&C1 DCD goes high when the remote modem’s carrier signal is

detected, and goes low when the carrier signal is not detected. &C2 DCD drops on disconnect for time set by S18, then goes high

again (for some PBX phone systems).

+ 39 hidden pages