How it Works
Multitech
Loading...
M
Loading...
Loading...
MultiVOIP MVP800
Quick Start Manual
43 pgs698.35 Kb0
User Manual
92 pgs1.83 Mb0

Multitech MultiVOIP MVP 800, MultiVOIP 800 MVP800 User Manual

Standalone Voice/IP Gateway
Model MVP 800
Proprietary Mode
User Guide
User Guide
S0000216 Revision A
MultiVOIP 800 (Model MVP 800)
Copyright © 2001, by Multi-Tech Systems, Inc.
Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Record of Revisions
Revision Description
A Manual released. This manual covers the MVP800 only and proprietary software version 3.01E. (06/18/01)
Patents
This Product is covered by one or more of the following U.S. Patent Numbers: 6151333, 5757801, 5682386. Other Patents Pending.
TRADEMARK
Trademark of Multi-Tech Systems, Inc. is the Multi-Tech logo. Windows is a registered trademark of Microsoft.
Multi-Tech Systems, Inc.
2205 Woodale Drive
Mounds View, Minnesota 55112
(763) 785-3500 or (800) 328-9717
Fax 763-785-9874
Tech Support (800) 972-2439
Internet Address: http://www.multitech.com
Contents
Chapter 1 - Introduction and Description
Introduction ................................................................................................................................................ 6
Preview of this Guide ................................................................................................................................. 6
MultiVOIP Application................................................................................................................................. 8
Front Panel Description.............................................................................................................................11
Back Panel Description ............................................................................................................................ 12
Power Connector ............................................................................................................................... 12
Command Port Connector ................................................................................................................. 12
10Base-T (Ethernet) Connector......................................................................................................... 12
Voice/Fax Channel............................................................................................................................. 12
Specifications ........................................................................................................................................... 13
Ethernet Port...................................................................................................................................... 13
Command Port................................................................................................................................... 13
Voice/Fax Channel............................................................................................................................. 13
Electrical/Physical.............................................................................................................................. 13
Chapter 2 - Installation
Installing Y our MultiVOIP.......................................................................................................................... 15
Configure and Install your Host MultiVOIP ........................................................................................ 15
Configure your Client MultiVOIPs ...................................................................................................... 15
Deploy the VOIP Network .................................................................................................................. 15
Safety Warning Telecom .......................................................................................................................... 15
Unpacking Y our MultiVOIP....................................................................................................................... 16
Safety Warnings....................................................................................................................................... 16
V alid VOIP Network Connections............................................................................................................. 16
Cabling Procedure ................................................................................................................................... 17
E&M Jumper Block Positioning Procedure ........................................................................................ 18
Chapter 3 - Software Loading and Configuration
Configuring Your Host MultiVOIP ............................................................................................................. 20
Configuring Your Client MultiVOIPs.......................................................................................................... 30
Deploy the VOIP Network ........................................................................................................................ 36
Chapter 4 - MultiVOIP Software
Introduction .............................................................................................................................................. 39
Before Y ou Begin............................................................................................................................... 39
MultiVOIP Configuration........................................................................................................................... 40
Changing Channel Parameters ................................................................................................................ 41
Interface T ab...................................................................................................................................... 41
Voice/Fax Tab .................................................................................................................................... 43
Regional T ab...................................................................................................................................... 44
Changing the Phone Directory Database................................................................................................. 45
Changing IP Parameters .......................................................................................................................... 47
Proxy Setup ....................................................................................................................................... 47
Viewing Statistics ..................................................................................................................................... 49
IP Statistics ........................................................................................................................................ 49
SNMP Statistics ................................................................................................................................. 50
Others Setup ............................................................................................................................................ 51
iii
Viewing Call Progress .............................................................................................................................. 52
Viewing Logs............................................................................................................................................ 53
Viewing Log Entry Details.................................................................................................................. 53
Viewing Channel Totals...................................................................................................................... 54
Reports..................................................................................................................................................... 54
Chapter 5 - Remote Configuration and Management
Introduction .............................................................................................................................................. 56
Remote Configuration .............................................................................................................................. 56
Modem-Based ................................................................................................................................... 56
LAN-Based ....................................................................................................................................... 58
Remote Management............................................................................................................................... 60
Telnet ................................................................................................................................................. 60
WEB Management............................................................................................................................. 62
Upgrade Procedures ................................................................................................................................ 63
One-Step Upgrade............................................................................................................................. 63
Manual Upgrade Procedure............................................................................................................... 65
Chapter 6 - Warranty, Service, and Tech Support
Introduction .............................................................................................................................................. 67
Limited Warranty ...................................................................................................................................... 67
On-line Warranty Registration............................................................................................................ 67
Tech Support ............................................................................................................................................ 68
Recording MultiVOIP Information ...................................................................................................... 68
Contacting T echnical Support ............................................................................................................ 68
Service ..................................................................................................................................................... 69
About the Internet..................................................................................................................................... 69
Appendixes
Appendix A - TCP/IP (Transmission Control Protocol/Internet Protocol) Description............................... 71
Appendix B - Cabling Diagrams ............................................................................................................... 74
Appendix C - Regulatory Information ....................................................................................................... 76
Class A Statement ............................................................................................................................. 76
Fax Branding Statement .................................................................................................................... 76
FCC Part 68 Telecom......................................................................................................................... 77
Canadian Limitations Notice .............................................................................................................. 78
EMC, Safety and Terminal Directive Compliance .............................................................................. 78
Glossary ........................................................................................................79
Index..............................................................................................................92
iv
Chapter 1 - Introduction and Description
Introduction
Welcome to Multi-Tech's new standalone Voice/IP Gateway which allows analog voice and fax communication over an IP network. Multi-Tech’s new voice/fax over IP gateway technology allows voice and fax communication to ride, with no additional expense, over your existing IP network, which has traditionally been data-only . To access this free voice and fax communication, all you have to do is connect your MultiVOIP to your telephone equipment, and then to your existing Ethernet LAN. Once configured, the MultiVOIP then allows voice and fax to travel down the same path as your traditional data communications.
The MVP800 is designed with eight voice/fax channels (which offer three voice/fax interfaces per channel), a 10M bps Ethernet LAN interface, and a command port for configuration.
System management is provided through the command port using bundled Windows® software which provides easy-to-use configuration menus and a comprehensive on-line help system.
Chapter 1 - Introduction and Description
Figure 1-1. MultiVOIP
Preview of this Guide
This guide describes the MultiVOIP and tells you how to install and configure the unit. The information contained in each chapter is as follows:
Chapter 1 - Introduction and Description
Chapter 1 describes the MultiVOIP. Front panel indicator , and back panel connector descriptions are provided. In addition, a list of relevant specifications is provided at the end of the chapter.
Chapter 2 - Installation
Chapter 2 provides information on unpacking and cabling your MultiVOIP. The installation procedure
describes each cable connection.
Chapter 3 - Software Loading and Configuration
Chapter 3 provides instructions for software loading and initial configuration. The MultiVOIP software
CD is Windows® based. Later chapters, as well as your online help program will describe the MultiVOIP software in more detail.
Chapter 4 - MultiVOIP Software
Chapter 4 describes the MultiVOIP software package designed for the Windows ® environment. This
chapter describes the software from an applications standpoint, and in so doing, not every element in the user interface is shown or defined. For explanations and parameters of each element dialog box please refer to the Help provided within the software.
6
Chapter 1 - Introduction and Description
Chapter 5 - Remote Configuration and Management
Chapter 5 provides procedures for changing the configuration of a remote MultiVOIP. Remote
configuration allows you to change the configuration of a unit by simply connecting two modems between the two MultiVOIPs and remotely controlling the unit. Chapter 5 also describes typical client applications such as Telnet and Web-based management, which are used for remote configuration of the MultiVOIP.
Chapter 6 - Warranty, Service and Tech Support
Chapter 6 provides instructions on getting service for your MultiVOIP at the factory, a statement of
the limited warranty , information about our Internet presence and user bulletin board service, and space for recording information about your MultiVOIP prior to calling Multi-Tech’s Technical Support.
Appendixes
Appendix A - Transmission Control Protocol/Internet Protocol (TCP/IP) Description Appendix B - Cabling Diagrams
Appendix C - Regulatory Information
7
MultiVOIP Application
A typical Voice Over IP (VOIP) network is shown in Figure 1-2 with a headquarters site and three remote sites (Sales office, regional and marketing offices). This typical Voice Over IP network can be set up via the Internet or your Intranet. The headquarters site is set up with a 8-channel MultiVOIP (MVP 800) connected to the headquarters LAN and eight voice/fax channels connected to the in­house telephone switch (PBX), only 4-channels are shown in Figure 1-2. T ypically, the MultiVOIP at the headquarters site would be set up as the host unit. The host unit controls the phone directory data base which is sent to each site on a periodic basis or if a new telephone number is added.
PSTN
512-4124
512-4123
512-4122
Headquarters
P B X
201.23.122.118
E&M Interface
7 6
5
101
4
Chapter 1 - Introduction and Description
Sales Office
PSTN
202
104
103
102
Internet/ Intranet
FXO
201
(5127)
FXS
205.24.123.119
KTS
522-5125
522-5124
522-5123
#301
#302
206.25.124.120
FXS Interface
Regional Office
207.26.125.121
402
E&M Interface
401
10
PSTN
9
P B X
532-6128
532-6129
Marketing Office
Figure 1-2. Example of a MultiVOIP application
The sales office is set up with a two voice/fax channel MultiVOIP series connected to the IP network and one voice/fax channel connected directly to the local Public Switch Telephone Network (PSTN). The second voice/fax channel is connected to the trunk side of a Key Telephone System (KTS). This allows an attendent to direct an incoming call to one of the two telephone extensions or to the fax machine.
The regional office is set up with two analog telephones connected directly to a two voice/fax channel MultiVOIP. This allows a person in the corporate office to dial out thru the MultiVOIP 800 at the corporate office and call directly into the person at extension 301.
The MultiVOIP at the marketing office is set up on the trunk side of the PBX (E&M interface) so that you could dial into the marketing office, seize a trunk, then dial an outside line to make a local call or connect directly to a telephone extension on the PBX or in this case to the fax machine at extension
6129. A phone directory database is maintained on one of the MultiVOIPs which is configured as a “host”.
This phone directory is retrieved by the remaining “client” MultiVOIPs on your Voice Over IP network. Each phone number entry corresponds to a MultiVOIP IP address and associated voice/fax channel
number. With this system, you need only update the “host” phone directory when deploying additional MultiVOIPs to your Voice Over IP network.
8
Phone Directory Data Base
Number Description Channel IP Address 101 Headquarters 1 201.23.122.118
Trunk Ext 4
102 Headquarters 2 201.23.122.118
Trunk Ext 5
103 Headquarters 3 201.23.122.118
Trunk Ext 6
104 Headquarters 4 201.23.122.118
Trunk Ext 7
201 Sales 1 205.24.123.119
KTS 201
202 Sales 2 205.24.123.119
PSTN 202
301 Regional 1 206.25.124.120
301
302 Regional 2 206.25.124.120
302
401 Marketing 1 207.26.125.121
Trunk Ext 9
402 Marketing 2 207.26.125.121
Trunk Ext 10
Chapter 1 - Introduction and Description
From the phone directory data base you can build your VOIP dialing directory. For example, if a person in our typical VOIP network at the headquarters picked up a telephone (for example extension
4123) and wanted to talk to some one at the Sales office, they would dial one of the four headquarters extension numbers (4, 5, 6, or 7). It makes no difference which extension you choose, because they all get you to the headquarters multiVOIP. A second dial tone is heard, then you would dial 201 to access channel 1 of the Sales MultiVOIP. This would ring the Key Telephone System (KTS) at the Sales office. An attendant at the Sales office would then direct your call.
9
Chapter 1 - Introduction and Description
Using the same example as above, but calling the Regional office. A person at headquarters would pick up a telephone and dial say trunk extension 5. This connects channel 2 of the headquarters MultiVOIP. A second dial tone is heard, then you would dial, for example, 301. The telephone connected to channel 1 of the Regional office MultiVOIP rings and your voice conservation takes place.
VOIP Dialing Directory
To call from
Headquarters to Sales Office
Headquarters to Marketing Office
Headquarters to Regional Office
Marketing Office to Headquarters
Marketing Office to Regional Office
Call Process
Pick up telephone and dial a trunk extension number (e.g., 4, 5, 6, or7). Second dial tone is generated, dial the Sales Office MultiVOIP (201). Attendent connects you to Sales office extension of called party
Pick up telephone and dial a trunk extension number (e.g., 4, 5, 6, or7). Second dial tone is generated, dial the Marketing Office MultiVOIP (401). Third dial tone is generated, dial the extension number of your calling party (6128).
Pick up telephone and dial a trunk extension number (e.g., 4, 5, 6, or 7). Second dial tone is generated, dial the Regional Office MultiVOIP (301).
Pick up telephone and dial a trunk extension number (e.g., 9 or 10). Second dial tone is generated, dial the Headquarters MultiVOIP (101) Third dial tone is generated, dial extension number of your calling party (4124).
Pick up telephone and dial a trunk extension number (e.g., 9 or 10). Second dial tone is generated, dial the regional MultiVOIP (301) and telephone rings.
Dialing Sequence
5 201 5123
6 401 6128
7 301
9 101
4124
10
301
10
Front Panel Description
The front panel contains three groups of LEDs that provide the status of the Ethernet connection, Voice/Fax channels, and general status of the MultiVOIP. The front panel is shown in Figure 1-3, and a description of each LED follows.
Figure 1-3. Front Panel
ETHERNET
RCV Receive Data indicator blinks when packets are being received from the local area network. LNK Link indicator lights when the Ethernet link senses voltage from a concentrator or external
device.
XMT Transmit Data indicator blinks when packets are being transmitted to the local area network. COL Collision indicator lights when a collision is detected on the Ethernet link.
Chapter 1 - Introduction and Description
VOICE/FAX CHANNEL _
FXS Foreign Exchange Station indicator lights when the voice/fax channel is configured for FXS
operation.
FXO Foreign Exchange Office indicator lights when the voice/fax channel is configured for FXO
operation.
E&M Ear and Mouth indicator lights when the voice/fax channel is configured for E&M operation. FAX Fax indicator lights when there is fax traffic on the voice/fax channel. XMT Transmit indicator blinks when voice packets are being transmitted to the local area network. RCV Receive indicator blinks when voice packets are being received from the local area network. XSG Transmit Signal indicator lights when the FXS-configured channel is off-hook, the FXO-
configured channel is receiving a ring from the Telco, or the M lead is active on the E&M configured channel (the MultiVOIP is receiving a ring from the PBX).
RSG Receive Signal indicator lights when the FXS-configured channel is ringing, the FXO-
configured channel has taken the line off-hook, or the E lead is active on the E&M-configured channel.
BOOT (BTG)
The BTG indicator lights when the MultiVOIP is booting or downloading setup.
POWER (PWR)
The Power indicator lights when power is applied to the MultiVOIP.
11
Back Panel Description
The cable connections for the MultiVOIP are made at the back panel. Connectors include Power , Command Port (RS232), Ethernet (10BASE-T), Voice/Fax Channels (E&M, FXO and FXS). The cable connectors are shown in Figure 1-4 and defined in the following groups.
VOICE/ FAX CHANNEL 8
E&M FXO FXS E&M FXO FXS E&M FXO FXS
VOICE/ FAX CHANNEL 4
CHANNEL 10
CHANNEL 9
Figure 1-4. Back Panel
Power Connector
The Power connector is used to connect the external power supply to the MultiVOIP. The Power connector is a 7-pin circular DIN connector. A separate power cord is connected to the power supply and the live AC grounded outlet.
Command Port Connector
VOICE/ FAX CHANNEL 7
VOICE/ FAX CHANNEL 3
CHANNEL 8
CHANNEL 7
E&M FXO FXS
CHANNEL 6
CHANNEL 5
VOICE/ FAX CHANNEL 6
VOICE/ FAX CHANNEL 2
CHANNEL 4
CHANNEL 3
VOICE/ FAX CHANNEL 5
VOICE/ FAX CHANNEL 1
Chapter 1 - Introduction and Description
INTERNAL COMPOSITE LINK
MONITOR XMT RCV
T1 DSU
GND
CHANNEL 2 (RS232/V.35)
CHANNEL 1 (RS232/V.35)
10BASET
ETHERNET
COMMAND PORT
EXT. COMPOSITE LINK (RS232/V.35)
I
POWER
O
The Command Port connector is used to configure the MultiVOIP using a PC with a serial port and running Windows® software. The Command Port connector is a DB-25 female connector.
10Base-T (Ethernet) Connector
The Ethernet 10Base-T connector is used to connect the MultiVOIP to a LAN using unshielded twisted cable. This connector is a keyed RJ-45 jack.
Voice/Fax Channel
The Voice/Fax channel connectors include three options per channel: E&M, FXO and FXS. E&M - This connector is used if you are connecting VOICE/FAX CHANNEL _ to the E&M trunk on a
PBX. This connector is an RJ-45 jack. FXO - This connector is used if you are connecting VOICE/FAX CHANNEL _ to the station side of a
PBX. This connector is an RJ-11 jack. FXS - This connector is used if you are connecting VOICE/F AX CHANNEL _ to a station device, etc.,
an analog telephone, KTS telephone system, or fax machine. This connector is an RJ-11 jack.
12
Specifications
• Two 1 Meg by 32 byte at 70 nanosecond SIMM is 8 Mb DRAM Caution: SIMM speed and size cannot be mixed
• Two Meg of flash memory
Ethernet Port
• Single Ethernet Interface - 10BASE-T (twisted pair) keyed RJ-45 connector.
Command Port
• Single 19.2K bps asynchronous Command Port with a DB-25 female connector
Voice/Fax Channel
• Two RJ-11 jacks (FXO and FXS)
• One RJ-45 jack (E&M)
Electrical/Physical
Chapter 1 - Introduction and Description
• Voltage - 115 VAC (Standard), 240 Volts AC (Optional)
• Frequency - 47 to 63 Hz
• Power Consumption - 18 Watts
• Dimensions - 3.75" high x 17.4" wide x 8" deep
8.9cm high x 44.2cm wide x 20.3cm deep
• Weight - 7.4 pounds (3.4 kg)
13
Chapter 2 - Installation
Installing Your MultiVOIP
The basic steps of installing your MultiVOIP network involve unpacking the units, connecting the cables, and configuring the units using the included management software (MultiVOIP Configuration). The recommended installation process includes three phases that, when completed, result in a fully functional Voice Over IP network. A general description of each phase is provided below, and detailed instructions follow throughout the rest of this section.
Configure and Install your Host MultiVOIP
First, the VOIP administrator configures the MultiVOIP designated as the “Host” unit. This includes the assignment of a unique LAN IP address, subnetwork mask, and Gateway IP address, as well as the selection of appropriate channel interface type for each of the Voice/Fax channels. Once all connections have been made, the VOIP administrator configures the unit and builds the Phone Directory Database that will reside with the Host unit.
Configure your Client MultiVOIPs
Next, the administrator configures the MultiVOIPs designated as “Client” units. The Client units can be another MVP 800 or MVP 400 unit or a MultiVOIP 200 series. Again, unique LAN IP addresses, subnetwork masks, and Gateway IP addresses are assigned, and each V oice/Fax channel is configured for the appropriate channel interface type. When this is done, the Phone Directory Database option is set to Client, and the IP address of the Host MultiVOIP is entered. Once all client units are configured, the network is ready for deployment.
Chapter 2 - Installation
Deploy the VOIP Network
The final phase of installation is deployment of the network. Through the first two phases, the VOIP administrator controls configuration. When the Client MultiVOIPs are sent to their remote sites, the remote site administrators need only to connect the units to their LAN and telephone equipment. A full Phone Directory Database (supplied by the Host MultiVOIP) will be loaded into their unit within minutes of being connected and powered up.
The final task of the VOIP Administrator is to develop the VOIP Dialing Directory based on the Phone Directory Database and telephone numbers of the interfacing telephone equipment. At this point, a VOIP User can call any person on the VOIP network.
Safety Warning Telecom
1. Never install telephone wiring during a lighting storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
3. This product is to be used with UL and cUL listed computers.
4. Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
5. Use caution when installing or modifying telephone lines.
6. Avaoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote rist of electrical shock from lighting.
7. Do not use the telephone to report a gas leak in the vicinity of the leak.
8. To reduct the risk of fire, use only No. 26 AWG or larger telecommunications line cord.
15
Unpacking Your MultiVOIP
Remove all items from the box.
Voice/Fax over IP Networks
www.multitech.com
Chapter 2 - Installation
Figure 2-1. Unpacking
Safety Warnings
Caution
Danger of explosion if battery is incorrectly replaced.
A lithium battery on the voice/fax channel board provides backup power for the time keeping capability. The battery has an estimated life expectancy of ten years.
When the battery starts to weaken, the date and time may be incorrect. If the battery fails, the board must be sent back to Multi-Tech Sytems for battery replacement.
The E&M, FXS, and Ethernet ports are not designed to be connected to a Public Telecommunication Network.
Valid VOIP Network Connections
The following VOIP network connections can be made at this time:
• FXS to FXS
• E&M Wink to E&M Wink
• FXS to FXO
• E&M Dial Tone to E&M dial tone
• E&M Wink to FXS ground
• E&M Dial Tone to FXS loop
• E&M Wink or dial tone to FXO
• FXO to FXO
16
Cabling Procedure
Cabling involves connecting the host MultiVOIP to your LAN and telephone equipment.
1. If you are connecting any Voice/Fax Channel to an E&M trunk other than type 2, perform the
E&M Jumper Block Positioning procedure which appears later in this chapter before connecting power to the unit.
2. Connect one end of the power supply to a live AC outlet and connect the other end to the
MultiVOIP as shown in Figure 2-2. The power connector is a 7-pin circular DIN connector.
Chapter 2 - Installation
VOICE/
FAX CHANNEL 8
VOICE/
FAX CHANNEL 4
VOICE/
FAX CHANNEL 7
E&M FXO FXS E&M FXO FXS E&M FXO FXS
VOICE/
FAX CHANNEL 3
CHANNEL 10
CHANNEL 8
CHANNEL 9
CHANNEL 7
VOICE/
FAX CHANNEL 6
E&M FXO FXS
VOICE/
FAX CHANNEL 2
CHANNEL 6
CHANNEL 4
CHANNEL 5
CHANNEL 3
Voice/Fax Channel 1 - 8 Connections
E&M
FXS
FXO
FXSE&M
FXO
VOICE/
FAX CHANNEL 5
VOICE/
FAX CHANNEL 1
CHANNEL 2 (RS232/V.35)
CHANNEL 1 (RS232/V.35)
10BASET
ETHERNET
COMMAND PORT
EXT. COMPOSITE LINK (RS232/V.35)
INTERNAL COMPOSITE LINK
MONITOR XMT RCV
T1 DSU
GND
I
POWER
O
Power Connection
Command Port Connection
PSTN
Ethernet Connection
Figure 2-2. Cable Connections
3. Connect the MultiVOIP to a PC by using the DB-25 (male) to DB-9 (female) cable provided in
your unit. Plug the DB-25 end of the cable into the Command port of the MultiVOIP and the other end into the PC serial port. See Figure 2-2.
4. Connect a network cable to the ETHERNET 10BASE-T connector on the back of the MultiVOIP.
Connect the other end of the cable to your network.
5. If you are connecting a station device such as an analog telephone, a fax machine, or a Key
Telephone System (KTS) to your MultiVOIP, connect one end of an RJ11 phone cord to the V oice/Fax Channel 1 FXS connector on the back of the MultiVOIP and the other end to the station device.
If you are connecting the station side of a telephone switch (PBX) to your MultiVOIP, connect one end of an RJ1 1 phone cord to the Voice/Fax Channel 1 FXO connector on the back of the MultiVOIP and the other end to the phone jack.
If you are connecting an E&M trunk from a telephone switch to your MultiVOIP, connect one end of an RJ45 phone cord to the V oice/Fax Channel 1 E&M connector on the back of the MultiVOIP and the other end to the trunk. Refer to Appendix B for E&M cabling pinout.
If you are connecting to an E&M trunk, you need ensure that the E&M trunk jumper is in the correct position for the E&M type trunk. The default E&M jumper position is E&M type 2. To change the E&M jumper position, perform the E&M jumper block positioning procedure.
6. Repeat the above step to connect the remaining telephone equipment to each Voice/Fax
Channel on your MultiVOIP.
7. Turn on power to the MultiVOIP by placing the ON/OFF switch on the back panel to the ON
position. Wait for the BTG LED on the MultiVOIP to go off before proceeding. This may take a few minutes.
Proceed to the next section to load the MultiVOIP software.
17
Chapter 2 - Installation
E&M Jumper Block Positioning Procedure
A jumper block exists for each voice/fax channel. The jumper block is to the right of each set of channel jacks. The jumper block contains 8-pairs of pins. The jumper plug fits over three pairs of pins on the jumper block. The E&M type number is labeled on the pc board. The jumper plug needs to be centered on the E&M type number. Perform the following procedure to change E&M jumper position.
1. Ensure that power is removed from the MultiVOIP
2. Remove the front panel by loosening the two Phillips quarter-turn screws.
3. Remove the screws at the back of the chassis, then slide the top cover back off the chassis to
expose the rear panel.
4. To change a jumper position, lift the jumper plug up off the jumper block and move to the new
position, ensuring that the center jumper is centered on the E&M type number.
2 (Default)
1,3
4
5
Figure 2-3. E&M Jumper Block
5. Change the jumper position for each voice/fax channel that is connecting to an E&M trunk that is
not a type 2. If you have two voice/fax channel boards in your unit and you need to change the jumpers on the second board, remove the six screws from the top board and disconnect the ribbon cable from the top board.
6. Slide the top cover back on to the chassis and replace the screws.
7. Replace the front panel and secure it by tightening the two Phillips quarter turn screws.
8. Return to the Cabling Procedure.
18
Chapter 3 - Software Loading and Configuration
Configuring Your Host MultiVOIP
The following software loading procedure does not provide every screen or option in the loading process. The assumption is that a technical person with a thorough knowledge of Windows and the software loading process is doing the installation. If you are installing a MultiVOIP behind a firewall, add the following UDP ports to your firewall.
Q.931 Signaling, Ch1[900] Q.931 Signaling, Ch2 [902] Q.931 Signaling, Ch3[904] Q.931 Signaling, Ch4 [906] Q.931 Signaling, Ch5[908] Q.931 Signaling, Ch6 [910] Q.931 Signaling, Ch7[912] Q.931 Signaling, Ch8 [914] Status [5000] Ch1 RTP [5004] Ch1 RTCP [5005] Ch2 RTP[5006] Ch2 RTCP [5007] Ch3 RTP[5008] Ch3 RTCP [5009] Ch4 RTP[5010] Ch4 RTCP [5011] Ch5 RTP[5012] Ch5 RTCP [5013] Ch6 RTP[5014] Ch6 RTCP [5015] Ch7 RTP[5016] Ch7 RTCP [5017] Ch8 RTP[5018] Ch8 RTCP [5019]
Refer to your firewall user documentation to enter and open these ports.
Chapter 3 - Software Loading and Configuration
1. Make certain that your MultiVOIP 800 has been properly cabled and that the power is turned on
and the boot light is off.
2. Insert the MultiVOIP 800 CD into your CD-ROM drive. The CD should start automatically. It may
take 10 to 20 seconds for the MultiTech CD installation window to display.
If the Multi-Tech Installation CD window does not display automatically , click My Computer, then right click the CD ROM drive icon, click Open, and then click the Autorun icon.
3. When the Multi-Tech Installation CD dialog box displays, click the Install Software icon.
20
Chapter 3 - Software Loading and Configuration
4. The Welcome dialog box displays.
Click Next to continue.
5. Follow the on-screen instructions to install your MultiVOIP software.
You may choose the Destination Location of your MultiVOIP software or you can accept the default destination by clicking Next. If you click Browse, you can choose from several folders. Accepting the default destination is recommended.
6. The following dialog box selects the COM port of your PC connected to the Command port of the
MultiVOIP. From the Select Port list, select the COM port of your PC.
Click OK to continue.
7. The Setup Complete dialog displays.
21
Chapter 3 - Software Loading and Configuration
Click Finish to continue.
8. The following message displays:
Click Yes to continue.
9. The IP Protocol Default Setup dialog box displays.
The default Frame T ype is TYPE_II. If this does not match your IP network, select the Frame Type from the Frame T ype list. The Frame Type choices are TYPE_II and SNAP.
10. In the Ethernet group, enter the IP Address, Subnet Mask, and Gateway Address, unique to
your IP LAN. The IP address is your unique LAN IP address, and the Gateway address is the IP address of the
device connected to the Internet/Intranet. Click OK when you are finished.
11. The Channel Setup dialog box displays. The Channel Setup dialog box defines the channel
interface, voice coder, fax parameters, and regional telephone parameters for each channel.
Configure each channel for the type of interface you are connecting to. Channel 1 displays by default in the Select Channel list. To change the channel number, select the channel number you want to configure from the Select Channel list.
12. The Interface group defaults to FXS (Loop Start). Select the interface option to correspond to
the interface type being connected to the Voice/Fax connector on the back panel of the MultiVOIP.
If you are connecting a station device such as an analog telephone, a fax machine, or a Key Telephone System (KTS) to the Voice/Fax connector on the back of the unit, FXS (Loop Start) will most likely be the correct Interface option most of the time.
If the station device uses ground start, then choose the FXS (Ground Start) option. Refer to the
22
Chapter 3 - Software Loading and Configuration
device’s user documentation. If you are using an extension from your PBX, then choose the FXO option. Check with your in-
house telephone personnel to verify connection type. If you are connecting to an E&M trunk on your PBX, then choose E&M option. If the E&M interface is selected, the E&M Options group is enabled. Check with your in-house
phone personnel to determine if the signaling is Dial T one or Wink and if the connection is 2-wire or 4-wire. If Wink signaling is used, then the Wink Timer is enabled with a default of 250 milliseconds. The range of the Wink T imer is from 100 to 350 milliseconds. Consult with your local in-house phone personnel for this timer setting. If the Pass Through check box is selected, a continuously open E&M voice path is established between two channels to pass voice packets. Available if the Dial Tone option is selected and auto-dialing is set up for the two channels that will be doing pass-through. This is useful for Public Address systems.
If you choose an FXO or FXS interface, the Dialing Options Regeneration group is enabled. Check with your in-house telephone personnel to verify whether your local PBX dial signaling is Pulse or DTMF (tone). Select the Regeneration option accordingly. In the Max Dial Digits box, enter the maximum number of digits allowed when dialing a phone number. The default setting is
5. In the Inter Digit Time box, enter the maximum amount of time in milliseconds that the unit will wait before mapping the dialed digits to an entry in the Phone Directory Database. If too much time elapses between digits and the wrong numbers are mapped, you hear a rapid busy signal. If this happens, hang up and dial again. This option is available for all interface types. In the Flash Timer box, enter the time, in milliseconds, for the duration of flash hook signals output on the FXO or FXS interface.
To dedicate a local voice/fax channel to a remote voice/fax channel, (so you will not have to dial the remote channel) select the Auto Call Enable check box. Enter the phone number of the remote VOIP in the Phone Number box.
For FXO-to-FXO communications, you can enable a specific type of FXO Disconnect: current loss, tone detection, or silence detection. Check with your in-house phone personnel to verify the preferred type of disconnect to use. For tone detection, you can select from the lists either one or two tones that will cause the line to disconnect. The person hanging up a call must then hit the key or keys that will produce those tones. For silence detection, select One Way or Two Way, then set the timer for the number of seconds of silence before disconnect. The default value of 15 seconds may be shorter than desired for your application.
The FXS Options control how the selected channel interacts with answering machines. If the Current Loss check box is selected, the local VOIP hangs up when the electrical current is lost. The remote VOIPs must also be configured for current loss. The Ring Count box contains the number of rings before the caller hears a Fast Busy signal. If this happens, hang up and try again. The default setting is 8 rings.
Note: After configuring a given channel, you can copy that channel’ s configuration to any other channel by clicking Copy. Everything on the Interface tab will be copied to the other channel.
13. Repeat the above steps to configure the interface type for each voice/fax channel. The Voice/
Fax tab displays the parameters for the voice coder, faxing, and DTMF gain.
23
Chapter 3 - Software Loading and Configuration
14. To change the voice coder, select the channel from the Select Channel list, then select the new
voice coder entry from the V oice Coder list.
If you changed the voice coder, ensure that the same voice coder is used on the voice/fax channel you are calling. Otherwise, you will always get a busy signal.
15. If you selected the FXO interface and are using touchtone dialing, you can set up the DTMF gain
(or output level in decibels - dB) for the higher and lower frequency groups of the DTMF tone pair. Make your selections from the lists in the DTMF Gain group. In the Duration box, enter the DTMF tone duration in milliseconds. 100 is entered by default
Note: Only change the DTMF gain under the direction of Multi-Tech Technical Support.
16. The Fax group enables you to send and receive faxes on the selected voice/fax channel. You
can select the maximum baud rate for faxes from the list in the Fax group. If you do not plan to send or receive faxes on a given voice/fax channel, you can disable faxes in the Fax group.
Note: After configuring a given channel, you can copy that channel’ s configuration to any other channel by clicking Copy. Everything on the Voice/Fax tab will be copied to the other channel.
17. Y ou can enable the voice/fax advanced features by selecting the Silence Compression, Echo
Cancellation, or Forward Error Correction check boxes. The Silence Compression check box defines whether silence compression is enabled for this
voice channel. If silence compression is enabled, the MultiVOIP 800 will not transmit voice packets when silence is detected, thereby reducing the amount of network bandwidth that is being used by the voice channel.
The Echo Cancellation check box defines whether echo cancellation is enabled for this voice channel. If echo cancellation is enabled, the MultiVOIP 800 will remove echo delay , which improves the quality of sound.
The Forward Error Correction (FEC) check box defines whether forward error correction is enabled for this voice channel. The FEC feature allows some of the voice packets that were corrupted or lost to be recovered. FEC adds an additional 50% overhead to the total network bandwidth consumed by the voice channel.
24
Chapter 3 - Software Loading and Configuration
18. The Billing/Security tab displays the parameters for automatic disconnection, billing options, and dialing options.
19. You can set up billing options for inbound and outbound calls by selecting them in the Billing Options group and then entering the charge in cents per number of seconds.
20. The Call Authentication option enables password protection for outbound and inbound calls on the selected voice/fax channel. If you enable password protection on inbound or outbound calls, you need to also enter a password of up to 14 numeric characters in the Password box.
21. The Automatic Disconnect option limits call duration to the number of seconds entered in the Disconnect After box. The default value of 180 seconds can be changed to any other value up to 65,535 (roughly 18.2 hours).
If your country/region is not the default USA, click the Regional tab and proceed to step 22. Otherwise, proceed to step 23 to begin building your phone directory database.
22. To change the Tone Pairs on the Regional tab, select your specific country or region from the Country/Region list. The Tone Pairs group displays the tones used in the selected country or region. If your country or region is not listed, click Custom to define it.
The Tone Pairs group parameters change per your choice. Click OK when finished.
23. Proceed to step 24 to begin building your phone directory database.
25
Chapter 3 - Software Loading and Configuration
24. The Phone Directory Database dialog box displays. You will build your personalized MultiVOIP Phone Directory in the following steps.
The MultiVOIP configured as a “Host” will contain the host database. The host database has the phone numbers of all the MultiVOIP’s available for communication on an IP network. This database is downloaded to each Client MultiVOIP as it comes online.
Click Add to begin building your phone directory database.
25. The Add/Edit Phone Entry dialog displays.
In the Station Information group, enter the unique phone number of the local device connected to Channel 1 in the Phone Number box. For example, phone number 101.
26. The Description is optional, but can be useful in associating the channel to the extension. If you want, enter a description of your local phone number. This description identifies the phone number you entered in the previous step.
27. The Permit Hunting option enables the answering unit to roll over to a second channel if the first channel is busy. Click Permit Hunting if you want the calls to roll over to a second voice/fax channel.
Note: The Host MultiVOIP must have a static IP address that the remote MultiVOIP can reference to obtain a downloaded copy of the host phone directory database.
26
Chapter 3 - Software Loading and Configuration
28. In the MultiVOIP Identification group, enter the IP address of the Host MultiVOIP in the IP Address box. For example, 204.22.122.1 18. Then obtain the 12-digit Node ID# (0008005xxxxx) from the ID plate on the back panel of the MultiVOIP and enter this number in the Ethernet Node ID box. If the ID plate is missing or damaged, you can also Telnet to the MultiVOIP and, on
the MultiVOIP Telnet Server menu enter 1 to advance to the Main Menu, then enter 3 for System Information where item 1 is the Ethernet Port Address you want to enter in the Ethernet Node ID box.
29. Click OK and you are returned to the Phone Directory Database dialog box, which now includes phone number 101 with its IP address, channel number , and description.
30. Click Add and the Add/Edit Phone Entry dialog box displays again.
31. Enter the phone number for the client MultiVOIP in the Station Information group Phone Number box. For example, 201.
32. Enter a description for the client MultiVOIP phone number for Channel 1 in the Description box. Note: If the client MultiVOIP is located behind a proxy server that uses a dynamically assigned IP
address, select Dynamic (disabling Static IP Address) and leave the Host IP Address box blank. The Host MultiVOIP will learn the IP address when it is contacted by the remote MultiVOIP.
33. Enter the IP address of the client MultiVOIP in the IP Address box in the MultiVOIP
Identification group. For example, 202.56.39.100.
27
Chapter 3 - Software Loading and Configuration
34. Click OK and you are returned to the Phone Directory Database dialog box, which now includes the second number and related information in the Phone Number list.
Note: If only Channel 1 is active, you must enter two phone numbers. The first number will be the local MultiVOIP phone number for Channel 1, and the second number will be the client MultiVOIP phone number for Channel 1.
35. When you have finished, click OK to download the setup configuration to the MultiVOIP.
36. The Checking dialog box displays.
Click OK to proceed.
37. After the setup is written to the MultiVOIP, the unit is rebooted.
38. Verify that the BTG LED on the MultiVOIP is of f after the download is complete. This may take several minutes as the MultiVOIP reboots.
39. Win3.1 users - you are returned to your Program Manager where the MultiVOIP Program Group and Program Item (Windows icons) have been created.
Win95/98/NT/2000 users - you are returned to your desktop. At this time, your MultiVOIP is configured. Proceed to the next section to configure the client MultiVOIPs.
28
Loading...
+ 64 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use