Multi-Tech Systems, Inc. makes no representations or warranties, whether express, implied or by estoppels, with respect to the content, information,
material and recommendations herein and specifically disclaims any implied warranties of merchantability, fitness for any particular purpose and noninfringement.
Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of
Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.
Legal Notices
The MultiTech products are not designed, manufactured or intended for use, and should not be used, or sold or re-sold for use, in connection with
applications requiring fail-safe performance or in applications where the failure of the products would reasonably be expected to result in personal injury or
death, significant property damage, or serious physical or environmental damage. Examples of such use include life support machines or other life
preserving medical devices or systems, air traffic control or aircraft navigation or communications systems, control equipment for nuclear facilities, or
missile, nuclear, biological or chemical weapons or other military applications (“Restricted Applications”). Use of the products in such Restricted
Applications is at the user’s sole risk and liability.
MULTITECH DOES NOT WARRANT THAT THE TRANSMISSION OF DATA BY A PRODUCT OVER A CELLULAR COMMUNICATIONS NETWORK WILL BE
UNINTERRUPTED, TIMELY, SECURE OR ERROR FREE, NOR DOES MULTITECH WARRANT ANY CONNECTION OR ACCESSIBILITY TO ANY CELLULAR
COMMUNICATIONS NETWORK. MULTITECH WILL HAVE NO LIABILITY FOR ANY LOSSES, DAMAGES, OBLIGATIONS, PENALTIES, DEFICIENCIES, LIABILITIES,
COSTS OR EXPENSES (INCLUDING WITHOUT LIMITATION REASONABLE ATTORNEYS FEES) RELATED TO TEMPORARY INABILITY TO ACCESS A CELLULAR
COMMUNICATIONS NETWORK USING THE PRODUCTS.
Contacting MultiTech
Knowledge Base
The Knowledge Base provides immediate access to support information and resolutions for all MultiTech products. Visit http://www.multitech.com/kb.go.
Support Portal
To create an account and submit a support case directly to our technical support team, visit: https://support.multitech.com.
About MultiConnect rCell 100 Series Router................................................................................................................ 7
Descriptions of LEDs.................................................................................................................................................... 10
Ethernet LED Descriptions .......................................................................................................................................... 10
Side Panel Connectors ................................................................................................................................................ 11
Frequency Bands (LEU1) ............................................................................................................................................. 14
Power Draw................................................................................................................................................................. 15
Regulatory Information Labels.................................................................................................................................... 17
User Responsibility...................................................................................................................................................... 19
Power Supply Caution ................................................................................................................................................. 19
Radio Frequency (RF) Safety ....................................................................................................................................... 20
Interference with Pacemakers and Other Medical Devices ...................................................................................... 20
Precautions for pacemaker wearers ........................................................................................................................ 21
Notice regarding Compliance with FCC, EU, and Industry Canada Requirements for RF Exposure ........................... 21
Chapter 4 – Antenna Information .......................................................................................................................... 22
Antenna System Cellular Devices................................................................................................................................ 22
Laird Antenna Used with -LAT1 and -LVW2 Models .................................................................................................. 22
LTE Antenna Used with -LEU1 Models ....................................................................................................................... 23
Chapter 5 – Installing the Router ........................................................................................................................... 25
Installing the Router.................................................................................................................................................... 25
Mounting the Device................................................................................................................................................... 25
Installing the SIM Card ............................................................................................................................................... 25
Resetting the Device ................................................................................................................................................... 26
Restoring User Defined Settings to the Device .......................................................................................................... 26
Chapter 6 – Using the Wizard to Configure Your Device......................................................................................... 28
Chapter 7 – Configuring Your Device...................................................................................................................... 31
Home Page (Dashboard) ............................................................................................................................................. 31
WAN Setup.................................................................................................................................................................. 32
Unavailable Services in PPP-IP Passthrough and Serial Modem Modes..................................................................... 33
Configuring IP Address and DNS Information for LAN ............................................................................................... 33
Configuring Dynamic Domain Naming System (DDNS) .............................................................................................. 33
Entering authentication information ....................................................................................................................... 34
Forcing a DDNS server update .................................................................................................................................. 34
Configuring Dynamic Host Configuration Protocol (DHCP) Server ............................................................................ 34
Configuring the Global Positioning System (GPS) ....................................................................................................... 35
Dumping NMEA Sentence Information to the Router's TCP Server Port ................................................................ 35
GPS Server Configuration.......................................................................................................................................... 35
Sending GPS information to a remote server .......................................................................................................... 36
Configuring the Serial Port ......................................................................................................................................... 37
Configuring Device to Act as Client .......................................................................................................................... 37
Configuring Device to Act as Server.......................................................................................................................... 38
Time Configuration .................................................................................................................................................... 39
Setting the Date and Time ....................................................................................................................................... 39
Configuring SNTP to Update Date and Time ............................................................................................................ 39
Editing or Deleting an Existing Network .................................................................................................................. 40
Unavailable Services in PPP-IP Passthrough and Serial Modem Modes..................................................................... 41
Chapter 8 – Setting Up Cellular Features ................................................................................................................ 42
Unavailable Services in PPP-IP Passthrough and Serial Modem Modes..................................................................... 44
4MultiConnect®rCell 100 MTR-LTE User Guide
CONTENTS
Configuring Wake Up On Call...................................................................................................................................... 44
Wake Up On Call Method Settings ........................................................................................................................... 44
Wake Up On Call General Configurations................................................................................................................. 45
Using Telnet to Communicate with the Cellular Radio............................................................................................... 45
Radio Status ................................................................................................................................................................ 46
Chapter 9 – Setting Up the Firewall........................................................................................................................ 47
MAC Filtering ............................................................................................................................................................ 48
SMS Field Descriptions.............................................................................................................................................. 50
Sending an SMS Message............................................................................................................................................ 52
Viewing Received SMS Messages ............................................................................................................................... 52
Viewing Sent SMS Messages....................................................................................................................................... 52
Setting Up GRE Tunnels ............................................................................................................................................. 54
Configuring IP Defense ............................................................................................................................................... 66
Denial of Service (DOS) Prevention........................................................................................................................... 66
Brute force ................................................................................................................................................................ 67
Unavailable Services in PPP-IP Passthrough and Serial Modem Modes..................................................................... 67
Generating a New Certificate...................................................................................................................................... 67
Uploading a New Certificate ....................................................................................................................................... 68
Setting up the Remote Management ......................................................................................................................... 68
Managing Your Device Remotely ................................................................................................................................ 68
Unavailable Services in PPP-IP Passthrough and Serial Modem Modes..................................................................... 69
Customizing the User Interface .................................................................................................................................. 72
Customizing Support Information ............................................................................................................................ 72
Saving and Restoring Settings .................................................................................................................................... 74
Using the Debugging Options ..................................................................................................................................... 75
Automatically rebooting the device.......................................................................................................................... 75
Setting up Telnet....................................................................................................................................................... 75
Ping and Reset Options ............................................................................................................................................. 76
Chapter 13 – Status and Logs ................................................................................................................................. 77
Service Statistics.......................................................................................................................................................... 78
Mail Log....................................................................................................................................................................... 78
Mail Queue.................................................................................................................................................................. 78
Chapter 14 – Appendix: Regulatory Information .................................................................................................... 80
47 CFR Part 15 Regulation Class B Devices ................................................................................................................. 80
Industry Canada Class B Notice................................................................................................................................... 80
Registration of Substances........................................................................................................................................ 82
Substances of Very High Concern (SVHC) ................................................................................................................ 82
Waste Electrical and Electronic Equipment Statement .............................................................................................. 82
Instructions for Disposal of WEEE by Users in the European Union ........................................................................ 82
Information on HS/TS Substances According to Chinese Standards ......................................................................... 84
Information on HS/TS Substances According to Chinese Standards (in Chinese) ...................................................... 85
6MultiConnect®rCell 100 MTR-LTE User Guide
PRODUCT OVERVIEW
Chapter 1 – Product Overview
About MultiConnect rCell 100 Series Router
This guide describes the MultiConnect rCell 100 Series Router. Use the rCell family of routers to provide secure
data communication between many types of devices that use legacy and the latest communication technologies.
Some device models support:
GPS capability
What's New in This Release
Manual versionUpdate description
2.4Software update: Additional SMS commands, SNMP and Open VPN tunnels
2.6RED compliance (H5-B07, H6-B07, and LEU1-B07 only)
The router has an integrated cellular modem and includes 10/100 BaseT Ethernet and RS-232 serial connectivity.
An image of the device follows:
Documentation
The following documentation is available at http://www.multitech.com/brands/multiconnect-rcell-100-series.
DocumentDescriptionPart Number
MultiConnect rCell100 Series
Router (MTR-LTE) User Guide
MultiConnect®rCell 100 MTR-LTE User Guide7
This document provides overview, safety and regulatory
information, design considerations, schematics, and device
information.
S000626
PRODUCT OVERVIEW
DocumentDescriptionPart Number
API Developer GuideYou can use the rCell API to manage configurations, poll
statistics, and issue commands. Documentation is available on
the MultiTech Developer Resources website at
AT Command release notes and basic operations for LEU1 and
LEU1-U Devices.
AT Command release notes and basic operations for LAT1 and
LAT1-U Devices.
AT Command release notes and basic operations for LVW2 and
LVW2-U Devices.
Lists AT Commands and parameters used to configure your
device. (Applies to LAT1 and LEU1 devices, not LVW2)
Product Build Options
ProductDescriptionCarrier/Region
MTR-LAT1-B07LTE router - cellular data onlyAT&T/North America
MTR-LAT1-B08LTE router - cellular data and GPSAT&T/North America
N/A
S000615
S000617
S000618
80421ST10585A
Rev 3
MTR-LVW2-B07LTE router - cellular data onlyVerizon/North America
MTR-LVW2-B08LTE router - cellular data and GPSVerizon/North America
MTR-LEU1-B07LTE router - cellular data only (RED compliant) Europe/Australia
MTR-LEU1-B08LTE router - cellular data and GPSEurope/Australia
8MultiConnect®rCell 100 MTR-LTE User Guide
Package Contents
Your MTR-LTE package includes the following:
ContentsDescription
1 - Power Supply with Removable Blades
1 - Ethernet Cable RJ45 6-ft.
2 - Cellular Antennas
1 - GPS Antenna (B08 models only)
PRODUCT OVERVIEW
Customer NoticesLegal and Support Information
Extended Services
1 - Mounting Tab and Bracket
4 - Rubber Feet
Note: The above information does not apply to the Router Only option.
MultiConnect®rCell 100 MTR-LTE User Guide9
PRODUCT OVERVIEW
Descriptions of LEDs
The top panel contains the following LEDs:
Power and Status LEDs—The Power LED indicates that DC power is present and the Status LED blinks when
the unit is functioning normally.
Modem LEDs—Two modem LEDs indicate carrier detection and link status.
Signal LEDs—Three signal LEDs display the signal strength level of the wireless connection.
Ethernet LEDs—These LEDs are not on the top panel. See the section Ethernet LED Descriptions for
descriptions of these LEDs.
LED Indicators
POWERIndicates presence of DC power when lit.
STATUSThe LED is a solid light when the device is booting up, saving the configuration, restarting,
or updating the firmware. When the Status LED begins to blink, the router is ready for use.
CDCarrier Detect. When lit, indicates data connection has been established.
LSLink Status
(for LVW2 only, not LAT1 and LEU1)
OFF — No power to the cellular radio
Continuously Lit — Not registered
Slow Blink (-0.2Hz) — Registered or connected
SIGNALSignal strength for cellular (RSSI range: 0 - 31)
ALL OFF — Unit is off, not registered on network, or extremely weak signal (0 <= RSSI <
6).
1 Bar “ON” — Very weak signal (7 <= RSSI <14).
1 Bar and 2 Bar “ON” — Weak signal (15 <= RSSI <23).
1 Bar, 2 Bar, and 3 Bar “ON” — Good signal (24 <= RSSI >= 31).
Ethernet LED Descriptions
Two Ethernet LEDs are physically on the RJ-45 connector(s). The table that follows describes these LEDs.
Ethernet LinkRight LED on Ethernet connector. Blinks when there is transmit and receive
activity on the Ethernet link. It shows a steady light when there is a valid
Ethernet connection.
Ethernet SpeedLeft LED on Ethernet connector. Lit when the Ethernet is linked at 100 Mbps.
If it is not lit, the Ethernet is linked at 10 Mbps.
10MultiConnect®rCell 100 MTR-LTE User Guide
PRODUCT OVERVIEW
Side Panel Connectors
The device has connectors on both sides of the housing. The right side of the device contains a SIM card holder, a
reset button, a GPS antenna connector, and a cellular-auxiliary antenna connector pair. Depending on the model of
your device, the GPS antenna connector may or may not be present.
The following shows the right side panel of the device:
The following shows the left side panel of the device. It includes an RS-232 connector, an Ethernet connector, and
the power receptacle.
The following table describes the items on the two side panels:
LabelDescription
CELL, AUXCellular antenna inputs. Use with the 2 Laird LTE DBA6927C1-FSMAM antennas or (for the
LEU1 only) with the 2 Wieson Technologies LTE GY115HT467-017 supplied with the device if
ordered as a bundle.
CELL - Primary. AUX - Diversity.
GPSGPS antenna input. Use with the Trimble GPS antenna 66800-52 supplied with the device
when ordered as a bundle. Used only on the B08 models.
SIMReceptacle for a SIM card (Subscriber Identity Module).
RESETResets the device. Refer to Resetting the Device or Resetting User Defined Settings to the
Device.
RS-232DE 9-pin, female-D Sub through-hole connector.
E-NETRJ-45 receptacle for standard Ethernet 10/100 Base-T (RJ-45 connecter has two Ethernet
LEDs).
Power7-32 VDC power receptacle for provided power cord. The device uses a minimum 7V 1.0A
power supply.
MultiConnect®rCell 100 MTR-LTE User Guide11
LTE SPECIFICATIONS
Chapter 2 – LTE Specifications
Dimensions
Specifications
CategoryMTR-LAT1 (North America
AT&T, T-Mobile)
General
PerformanceLTE Cat. 3GPP Release 9
Frequency Bands (MHz)4G LTE: 700 (B17) / 850
(B5) / AWS1700 (B4) /1900
(B2)
3G UMTS | HSPA+:850 (B5)
/ 1900(B2)
2G: GSM | GPRS | EDGE:
850/1900
Cellular radio moduleTelit LE910-NAGTelit LE910-SVGTelit LE910-EUG
GPS radio moduleSKYTRAQ Venus638LP (for B08 models only)
MTR-LVW2 (North
America Verizon)
4G LTE: Single-mode: 700
(B13) / AWS1700 (B4)
MTR-LEU1 (EU Carriers)
See the following
Frequency Bands table for
details.
12MultiConnect®rCell 100 MTR-LTE User Guide
LTE SPECIFICATIONS
CategoryMTR-LAT1 (North America
AT&T, T-Mobile)
MTR-LVW2 (North
America Verizon)
MTR-LEU1 (EU Carriers)
Cellular packet dataUp to 100 Mbps downlink (Theoretical maximum - actual performance may be
affected by multiple environmental factors.)
Up to 50 Mbps uplink (See above note.)
Diversity/MIMORx Diversity and MIMO DL 2x2
SMSPoint-to-Point messaging, Mobile terminated SMS, Mobile originated SMS
Connectors
CellularFemale SMA connector
GPSFemale SMA connector
SIM HolderMini-SIM standard 1.8 V
and 3 V
N/AMini-SIM standard 1.8 V
and 3 V
eNet (LAN)RJ-45, 10/100 Base T
GPSFemale SMA connector
RS-232DCE 9-pin, female connector
Power25 mm miniature locking power jack (screw on)
Power Requirements
1
Voltage7 V to 32 V DC
Physical Description
Dimensions4.17” x 3.0” x 1.15” (10.6cm x 7.6cm x 2.9cm)
Weight0.51 lbs (0.231 Kg)
Chassis typeAluminum
Environment
Operating Temperature
Storage Temperature
2
-40° C to +80° C
2
-40° C to +85° C
HumidityRelative humidity 15% to 93% non-condensing
Certifications, Compliance, Warranty
RegulatoryFCC Class B (U.S.), IC
FCC Class B (U.S.)CE Mark, RED (EU)
(Canada)
SafetyUL60950-1, UL 201,
UL60950-1, UL 201IEC60950-1(EU)
cUL60950-1
NetworkPTCRB, AT&T, T-MobileVerizon (pending)Telstra, EU carriers
QualityDesigned and built-in ISO 9001/13485 facilities
MIL-STD-810: High Temp, Low Temp, Cold Dwell, Random, and Sine vibration
SAE J1455: Random and Sine vibration
MultiConnect®rCell 100 MTR-LTE User Guide13
LTE SPECIFICATIONS
1
Optional power supply must be a Listed ITE power supply marked LPS or Class 2 rated 1.0 A minimum.
Certification does not apply or extend to voltages outside certified range, and has not been evaluated by UL for
operating voltages beyond tested range.
2
UL Recognized @ 40° C, Limited by AC power supply. UL Recognized @ 60° C when used with the fused DC power
cable, part number FPC-532-DC.
Installation in outdoor locations has not been evaluated by UL. UL Certification does not apply or extend to
outdoor applications.
Note: Radio performance may be affected at the temperature extremes. This is considered normal. There is no
single cause for this function. Rather, it is the result of an interaction of several factors, such as the ambient
temperature, the operating mode, and the transmit power.
A lithium battery (3V, coin cell, CR1632) located within the product provides backup power for the
timekeeping. This battery has an estimated life expectancy of ten years.
When this battery starts to weaken, the date and time may be incorrect.
Battery is not user replaceable. If the battery fails, the device must be sent back to MultiTech Systems for
battery replacement.
Lithium cells and batteries are subject to the Provisions for International Transportation. Multi-Tech
Systems, Inc. confirms that the Lithium batteries used in the MultiTech product(s) referenced in this manual
comply with Special Provision 188 of the UN Model Regulations, Special Provision A45 of the ICAO-TI/IATADGR (Air), Special Provision 310 of the IMDG Code, and Special Provision 188 of the ADR and RID (Road and
Rail Europe).
CAUTION: Risk of explosion if this battery is replaced by an incorrect type. Dispose of batteries according to
instructions.
Attention: Risque d'explosion si vous remplacez la batterie par un modèle incompatible. Jetez les piles usagées
selon les instructions.
SAFETY WARNINGS
User Responsibility
Respect all local regulations for operating your wireless device. Use the security features to block unauthorized use
and theft.
Power Supply Caution
CAUTION: Do not replace the power supply with one designed for another product; doing so can damage the
modem and void your warranty.
CAUTION: Pour garantir une protection continue contre les risques d'incendie, remplacez les fusibles
uniquement par des fusibles du même type et du même calibre.
Device Maintenance
When maintaining your device:
Do not attempt to disassemble the device. There are no user serviceable parts inside.
Do not misuse the device. Follow instructions on proper operation and only use as intended. Misuse could
make the device inoperable, damage the device and/or other equipment, or harm users.
Do not apply excessive pressure or place unnecessary weight on the device. This could result in damage to
the device or harm to users .
Do not use this device in explosive or hazardous environments unless the model is specifically approved for
such use. The device may cause sparks. Sparks in explosive areas could cause explosion or fire and may
result in property damage, severe injury, and/or death.
Do not expose your device to any extreme environment where the temperature or humidity is high. Such
exposure could result in damage to the device or fire.
Do not expose the device to water, rain, or spilled beverages. It is not waterproof. Exposure to liquids could
result in damage to the device.
MultiConnect®rCell 100 MTR-LTE User Guide19
SAFETY WARNINGS
Do not place the device alongside computer discs, credit or travel cards, or other magnetic media. The
information contained on discs or cards may be affected by the device.
Using accessories, such as antennas, that MultiTech has not authorized or that are not compliant with
MultiTech's accessory specifications may invalidate the warranty.
If the device is not working properly, contact MultiTech Technical Support.
Vehicle Safety
When using your device in a vehicle:
Do not use this device while driving.
Respect national regulations on the use of cellular devices in vehicles.
If incorrectly installed in a vehicle, operating the wireless device could interfere with the vehicle’s
electronics. To avoid such problems, use qualified personnel to install the device. The installer should verify
the vehicle electronics are protected from interference.
Using an alert device to operate a vehicle’s lights or horn is not permitted on public roads.
UL evaluated this device for use in ordinary locations only. UL did NOT evaluate this device for installation in
a vehicle or other outdoor locations. UL Certification does not apply or extend to use in vehicles or outdoor
applications.
Radio Frequency (RF) Safety
Due to the possibility of radio frequency (RF) interference, it is important that you follow any special regulations
regarding the use of radio equipment. Follow the safety advice given below.
Operating your device close to other electronic equipment may cause interference if the equipment is
inadequately protected. Observe any warning signs and manufacturers’ recommendations.
Different industries and businesses restrict the use of cellular devices. Respect restrictions on the use of
radio equipment in fuel depots, chemical plants, or where blasting operations are in process. Follow
restrictions for any environment where you operate the device.
Do not place the antenna outdoors.
Switch OFF your wireless device when in an aircraft. Using portable electronic devices in an aircraft may
endanger aircraft operation, disrupt the cellular network, and is illegal. Failing to observe this restriction
may lead to suspension or denial of cellular services to the offender, legal action, or both.
Switch OFF your wireless device when around gasoline or diesel-fuel pumps and before filling your vehicle
with fuel.
Switch OFF your wireless device in hospitals and any other place where medical equipment may be in use.
Interference with Pacemakers and Other Medical Devices
Potential interference
Radio frequency energy (RF) from cellular devices can interact with some electronic devices. This is
electromagnetic interference (EMI). The FDA helped develop a detailed test method to measure EMI of implanted
cardiac pacemakers and defibrillators from cellular devices. This test method is part of the Association for the
Advancement of Medical Instrumentation (AAMI) standard. This standard allows manufacturers to ensure that
cardiac pacemakers and defibrillators are safe from cellular device EMI.
20MultiConnect®rCell 100 MTR-LTE User Guide
SAFETY WARNINGS
The FDA continues to monitor cellular devices for interactions with other medical devices. If harmful interference
occurs, the FDA will assess the interference and work to resolve the problem.
Precautions for pacemaker wearers
If EMI occurs, it could affect a pacemaker in one of three ways:
Stop the pacemaker from delivering the stimulating pulses that regulate the heart's rhythm.
Cause the pacemaker to deliver the pulses irregularly.
Cause the pacemaker to ignore the heart's own rhythm and deliver pulses at a fixed rate.
Based on current research, cellular devices do not pose a significant health problem for most pacemaker wearers.
However, people with pacemakers may want to take simple precautions to be sure that their device doesn't cause
a problem.
Keep the device on the opposite side of the body from the pacemaker to add extra distance between the
pacemaker and the device.
Avoid placing a turned-on device next to the pacemaker (for example, don’t carry the device in a shirt or
jacket pocket directly over the pacemaker).
Notice regarding Compliance with FCC, EU, and Industry Canada
Requirements for RF Exposure
The antenna intended for use with this unit meets the requirements for mobile operating configurations and for
fixed mounted operations, as defined in 2.1091 of the FCC rules for satisfying RF exposure compliance. This device
also meets the European RF exposure requirements of EN 62311. If an alternate antenna is used, consult user
documentation for required antenna specifications.
Compliance of the device with the FCC, EU and IC rules regarding RF Exposure was established and is given with
the maximum antenna gain as specified above for a minimum distance of 20 cm between the devices radiating
structures (the antenna) and the body of users. Qualification for distances closer than 20 cm (portable operation)
would require re-certification.
Wireless devices could generate radiation. Other nearby electronic devices, like microwave ovens, may also
generate additional radiation to the user causing a higher level of RF exposure.
MultiConnect®rCell 100 MTR-LTE User Guide21
ANTENNA INFORMATION
Chapter 4 – Antenna Information
Antenna System Cellular Devices
The cellular/wireless performance depends on the implementation and antenna design. The integration of the
antenna system into the product is a critical part of the design process; therefore, it is essential to consider it early
so the performance is not compromised. If changes are made to the device's certified antenna system, then
recertification will be required by specific network carriers.
The antenna system is defined as the UFL connection point from the gateway to the specified cable specifications
and specified antenna specifications.
Laird Antenna Used with -LAT1 and -LVW2 Models
The cellular radio portion of the device is approved with the following antenna or for alternate antennas meeting
the given specifications.
The cellular radio portion of the device is approved with the following antenna or for alternate antennas meeting
the given specifications.
Manufacturer:Wieson Technologies
Description:LTE Antenna
Model Number:GY115HT467-017
MultiTech Part Number:95218146LF
MultiTech ordering information:
ModelQuantity
ANLTE2-2HRA2
ANLTE2-10HRA10
ANLTE2-50HRA50
LTE Antenna Specifications
CategoryDescription
Frequency Range690-960 MHz
1710-2170 MHz
2300-2690 MHz
Impedance50 Ohms
VSWR3:1
Peak Radiated Gain3.5 dBi
RadiationOmni-directional
PolarizationLinear
GPS Antenna Specifications
Manufacturer:Trimble
Description:GPS Antenna with low noise amplifier
Model Number:66800-52
MultiConnect®rCell 100 MTR-LTE User Guide23
ANTENNA INFORMATION
Multi-Tech Part Number:45009665L
MultiTech Ordering Information
ModelQuantity
ANGPS-1MM1
ANGPS-10MM10
ANGPS-50MM50
Antenna Specifications
CategoryDescription
Frequency Range1575.24 MHz
Impedance50 Ohms
VSWR2.0:1 max
Gain10-30 dBi
LNA Current Consumption40 mA max
Noise Figure< 2dB
PolarizationRHCP
Input voltage3.0V M M 0.2V
24MultiConnect®rCell 100 MTR-LTE User Guide
Chapter 5 – Installing the Router
Installing the Router
1.To use the router’s cellular features, connect two suitable antennas to both the CELL and AUX
connectors.
2.You must use diversity because this device requires two antennas.
3.Using an Ethernet cable, connect one end of the cable to the E-NET connector on the back of the router
and the other end to your computer, either directly or through a switch or hub.
4.If you are connecting to a serial interface, connect the DE-9 connector (9-pin) of the RS-232 cable to the
RS-232 connector on the router. Then connect the other end to the serial port on the desired device.
5.Some routers support the use of a GPS receiver. If you are using a GPS receiver with the router, attach
the GPS cable to the GPS connector on the router.
6.Attach a power cable to your power supply module.
7.Screw-on the power lead from the power supply module into the power connection on the router.
8.Plug the power supply into your power source.
The POWER LED lights after the device powers up.
When the Status LED begins to blink, the device is ready for use.
9.You can configure your router by using your router’s web management interface. You might need to
change the IP address of your computer to be in the same IP and subnet mask range as the device.
INSTALLING THE ROUTER
a.Open a web browser. In the browser's address field, type the default address for the router:
http://192.168.2.1. (If the browser displays a message that there is a problem with the website's
security certificate, ignore this and click Continue to the webpage).
b.A login page opens. In the username field, type the default user name: admin (all lower-case).
c.In the password field, type the default password: admin (all lower-case).
d.Click Login. The Web Management Home page opens. Online documentation included with the web
management interface describes how to configure your router.
Mounting the Device
1.Locate the groove on the bottom of the modem.
2.Slide the mounting rod through the groove.
3.To secure the rod to the desired surface, place and tighten two screws in the holes on either end of the
mounting rod. The dimensions illustration in this guide shows the mounting rod, as well as the
dimensions for placement of the screws.
Installing the SIM Card
If you want to operate the router on a particular network, install a SIM card (Subscriber Identity Module).
To install the SIM:
1.Locate the SIM card slot on the side of the router. The slot is labeled SIM.
MultiConnect®rCell 100 MTR-LTE User Guide25
INSTALLING THE ROUTER
2.Push the SIM card into the slot until it snaps into place.
3.To remove the SIM, push the edge of the card in. When released, the card pops out of the device.
Resetting the Device
You need:
A pin, paperclip, or similar thin object that can fit into the reset hole
The following is the default condition for the RESET button on the device. You can program a change to the
behavior of the button if needed.
To reset the device:
1.Find the hole labeled RESET. The reset button is recessed into the case.
2.Use the pin to press and release the RESET button as follows:
Reset options:
To reboot, press RESET for less than 3 seconds.
To reboot and restore user-defined defaults (if previously set), press RESET for 3 to 29
seconds.
To reboot, restore factory settings, and erase user-defined defaults, press RESET for 30
seconds or longer.
Note: The device reboots when restoring settings.
Restoring User Defined Settings to the Device
You can restore user defined settings to your device.
You need:
A pin, paperclip, or similar thin object that can fit into the reset hole
1.Locate the hole in the panel labeled RESET. The reset button is recessed into the housing.
2.Use the pin to press in the button for about 3 seconds and then release the reset button.
26MultiConnect®rCell 100 MTR-LTE User Guide
Loading...
+ 59 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.