Multitech MTCBA-C-EN-N14, MTCBA-C-EN-N9, MTCBA-C-EN-N2, MTCBA-C-EN-N4, MTCBA-G-EN-F1 Quick Start Manual

MultiModem®

Wireless EDGE, GPRS, CDMA Modems

with Ethernet Interface

Quick Start Guide

Copyright and Technical Support

Cabling Guide

MultiModem® Wireless Modem with Ethernet Interface
MTCBA-E-EN, MTCBA-G-EN-Fx, MTCBA-C-EN-Nx
82010074L, Revision E

Copyright © 2005-8 by Multi-Tech Systems, Inc.

This publication may not be reproduced, in whole or in part, without prior
expressed written permission from Multi-Tech Systems, Inc. All rights
reserved. Multi-Tech Systems, Inc. makes no representations or warranty with
respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this
publication and to make changes from time to time in the content hereof
without obligation of Multi-Tech Systems, Inc. to notify any person or
organization of such revisions or changes. Check Multi-Tech’s Web site for
current versions of our product documentation.

Record of Revisions
Revision Date Description

D 11/16/07 Updated Hazardous Warnings statements. The

E 03/07/08 Updated for software version 1.19.

Trademarks

Trademarks and registered trademarks of Multi-Tech Systems, Inc. include
MultiModem, the Multi-Tech logo, and Multi-Tech. All products or technologies
are the trademarks or registered trademarks of their respective holders.

Technical Support
Country By Email By Phone

Europe, Middle East, Africa: [e-mail]
U.S., Canada, all others: [e-mail]
763-717-5863

World Headquarters

Multi-Tech Systems, Inc.
2205 Woodale Drive
Mounds View, Minnesota 55112
763-785-3500 or 800-328-9717
Fax [phone]
Internet Address: http://www.multitech.com

Wireless Activation section now sends the user
to the Wireless Activation Notices for directions
on activating a wireless account. Add AT
Command for changing quad-band frequency.

+(44) 118 959 7774

800 972-2439 or

2 Multi-Tech Systems, Inc. Quick Start Guide

MultiModem Wireless Modem with Ethernet Interface

Introduction

The purpose of this guide is to cover safety concepts, the basic
connections, and general setup of the Multi-Tech wireless
MultiModem with Ethernet interface. For detailed information see the
User Guide which is available on the MultiModem CD accompanying
your wireless product and on the Multi-Tech Web site.

Check Multi-Tech’s Web site for current versions of our product
documentation.

Safety

Ethernet Ports Caution

The Ethernet ports are not designed to be connected to a Public
Telecommunication Network.

Handling Precautions

All devices must be handled with certain precautions to avoid
damage due to the accumulation of static charge. Although input
protection circuitry has been incorporated into the devices to
minimize the effect of this static build up, proper precautions
should be taken to avoid exposure to electrostatic discharge
during handling and mounting.

Caution: Maintain a separation distance of at least 20 cm (8

inches) between the transmitter’s antenna and the body of
the user or nearby persons. The modem is not designed for,
nor intended to be, used in applications within 20 cm (8
inches) of the body of the user.

Safety Instructions for Hazardous Locations

Installation Instructions

1. The modems are open devices intended for installation in

an ultimate enclosure suitable for the intended application.

2. THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I,

DIVISION 2, GROUPS A, B, C, AND D OR NON­HAZARDOUS LOCATIONS ONLY.

Multi-Tech Systems, Inc. Quick Start Guide 3

MultiModem Wireless Modem with Ethernet Interface

3. “WARNING – Explosion Hazard – Substitution of

Components may Impair Suitability for Class I, Division 2”.

4. “WARNING – Explosion Hazard – Do not Disconnect

Equipment Unless Power has been switched off or the
area is known to be Non-hazardous”.

5. “WARNING – Explosion Hazard – Do not replace fuse

unless power has been switched off or the area is known
to be non-hazardous”

6. “WARNING – Do not install or remove SIM card unless

power has been switched off or the area is known to be
non-hazardous”.

Vehicle Safety

• Do not use your Wireless MultiModem while driving, unless

equipped with a correctly installed vehicle kit allowing ‘Hands­Free’ Operation.

• Respect national regulations on the use of cellular telephones

in vehicles. Road safety always comes first.

• If incorrectly installed in a vehicle, the operation of Wireless

MultiModem telephone could interfere with the correct
functioning of vehicle electronics. To avoid such problems, be
sure that qualified personnel have performed the installation.
Verification of the protection of vehicle electronics should be
part of the installation.

• The use of an alert device to operate a vehicle’s lights or horn

on public roads is not permitted.

4 Multi-Tech Systems, Inc. Quick Start Guide

MultiModem Wireless Modem with Ethernet Interface

Ship Kit Contents

Unbundled Package

Modem with Not Accessories

1 modem
1 fused DC power cable
4 rubber feet for flat
surface mounting
1 Quick Start Guide
1 MultiModem CD

Note: You must supply

an antenna.

Note: See the User Guide for antenna specifications.

Bundled Package

Modem with Accessories

1 modem
1 power supply cable

(varies)
4 rubber feet for flat
surface mounting
1 antenna
1 Quick Start Guide
1 MultiModem CD

Set Up Your Wireless Modem

Obtain a Wireless Account

Please see the wireless account Activation Notices located
on the MultiModem CD. Choose the one for your wireless
network provider and follow the directions to activate your
account.

Phone Numbers for the Wireless Modem

Every wireless modem will have its own unique phone number.
The phone number may simply be given to you by your
wireless service provider. For GPRS and EDGE, it may also be
on the SIM card. Wireless provider implementations may vary.

Multi-Tech Systems, Inc. Quick Start Guide 5