Multiquip WM-90P, WM-90S User Manual

PARTS MANUAL

SERIES

MODEL WM-90S (STEEL)

MODEL WM-90P (PLASTIC)

PLASTER AND MORTAR MIXER

(GASOLINE ENGINE/ELECTRIC MOTOR)

Revision #6 (03/04/08)

To find the latest revision of this

publication, visit our website at:

www.multiquip.com

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingand other constructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of these chemicals are:

Leadfromlead-based paints.
Crystallinesilica frombricks.
Cementand other masonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.

Your risk from these exposures varies,
dependingon howoften youdo this type
of work. To reduce your exposure to
these chemicals: work in aALWAYS
well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed
to filter out microscopic particles.

PAGE 2 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90 S/P PLASTER/MORTAR MIXER — TABLE OF CONTENTS

MQ-WHITEMAN — WM-90S/P
Plaster/Mortar Mixer

Here's How To Get Help ........................................... 2

Table Of Contents .................................................... 3

Parts Ordering Procedures ...................................... 4

Explanation of Code In Remarks Column................ 6

Suggested Spare Parts ............................................ 7

Component Drawings

Nameplate and Decals.......................................... 8-9

Frame Assembly ...............................................10-11

Paddle Shaft Assembly ..................................... 12-13

Steel Drum Assembly........................................14-15

Plastic Drum Assembly ..................................... 16-17

Drum & Paddle Shaft Complete Assy. (Poly) ..... 18-19

Drum & Paddle Shaft Complete Assy. (Steel) ...20-21

Axle Assembly ...................................................22-23

Engine Assembly ..............................................24-25

Electric Motor Assembly.................................... 26-27

Cabinet Assembly ............................................. 28-29

HONDA GX240K1HA2 ENGINE

Air Cleaner Assembly........................................30-31

Camshaft Assembly ..........................................32-33

Carburetor Assembly ........................................ 34-35

Control Assembly ..............................................36-37

Crankcase Cover Assembly ..............................38-39

Crankshaft Assembly ........................................40-41

Cylinder Barrel Assembly ..................................42-43

Cylinder Head Assembly ...................................44-45

Fan Cover Assembly .........................................46-47

Flywheel Assembly ...........................................48-49

Muffler Assembly ..............................................50-51

Fuel Tank Assembly ..........................................52-53

Ignition Coil ....................................................... 54-55

Piston Assembly ................................................56-57

Recoil Starter ....................................................58-59

Gear Reduction Assembly ................................60-61

Label Assembly .................................................62-63

Terms and Conditions of Sale — Parts .................. 64

NOTE

Specifications and are
subject to change
without notice.

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 3

PARTS ORDERING PROCEDURES

Ordering parts has never been easier!

Choose from three easy options:

Effective:

January 1

st

, 2006

Best Deal!

Order via Internet (Dealers Only):

Order parts on-line using Multiquip’s SmartEquip website!

■

View Parts Diagrams

■

Order Parts

■

Print Specification Information

Goto www.multiquip.com and click on

Order Parts

to log in and save!

Order via Fax (Dealers Only):

All customers are welcome to order parts via Fax.

Domestic (US) Customers dial:

1-800-6-PARTS-7 (800-672-7877)

Non-Dealer Customers:

Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.

Order via Phone:

If you have an MQ Account, to obtain a
Username and Password, E-mail us at:

[e-mail].

To obtain an MQ Account, contact your
District Sales Manager for more information.

internet

Use the
on

Standard orders

and qualify for a 5% Discount

for all orders which include

complete part numbers.*

Fax

your order in and qualify for a 2% Discount

on

Standard orders

for all orders which include

complete part numbers.*

Domestic (US) Dealers Call:

1-800-427-1244

International Customers

their local Multiquip Representatives for
Parts Ordering information.

Note: Discounts Are Subject To Change

Note: Discounts Are Subject To Change

should contact

❒❒

❒

❒❒

❒❒

❒

❒❒

❒❒

❒

❒❒

❒❒

❒

❒❒
❒❒

❒

❒❒

❒❒

❒

❒❒

www.multiquip.com

PAGE 4 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

When ordering parts, please supply:

❒❒

❒

Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)

Return Fax Number
Applicable Model Number

Quantity, Part Number and Description of Each Part

All orders are treated as
and will ship the same day if received prior
to 3PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

❒❒

Standard Orders

Specify Preferred Method of Shipment:

✓

UPS/Fed Ex

■

Priority One

■

Ground

■ Next Day

■

Second/Third Day

✓ DHL
✓

Tr u c k

NOTE PAGE

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 5

EXPLANATION OF CODE IN REMARKS COLUMN

The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the help
numbers found on the back page of the manual if there are any
questions.

The contents and part numbers listed in the parts section are
subject to change
guarantee the availibility of the parts listed.

Sample Parts List:

NO. PART NO. PART NAME QTY. REMARKS

1 12345 BOLT ...................... 1 ......INCLUDES ITEMS W/

2

*

2*12347 WASHER, 3/8 IN. ... 1 ......

3 12348 HOSE ................... A/R .... MAKE LOCALLY

4 12349 BEARING ............... 1 ...... S/N 2345B AND ABOVE

NO. Column

Unique Symbols - All items with same unique symbol

(*, #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.

Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general
item, such as different size saw blade guards in use or a
part that has been updated on newer versions of the same
machine.

When ordering a part that has more than one
item number listed, check the remarks column
for help in determining the proper part to order.

without notice

WASHER, 1/4 IN. .............

. Multiquip does not

NOT SOLD SEPARATELY
MQ-45T ONLY

*

QTY. Column

Numbers Used - Item quantity can be indicated by a

number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts

that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold

separately. Other entries will be clarified in the “Remarks”
Column.

REMARKS Column

Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.

Assembly/Kit

unique symbol will be included when this item is purchased.

Indicated by:

“INCLUDES ITEMS W/(unique symbol)”

Serial Number Break

number range where a particular part is used.

Indicated by:

“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”

Specific Model Number Use

used only with the specific model number or model number
variant listed. It can also be used to show a part is NOT
used on a specific model or model number variant.

Indicated by:

“XXXXX ONLY”
“NOT USED ON XXXX”

- All items on the parts list with the same

- Used to list an effective serial

- Indicates that the part is

PART NO. Column

Numbers Used - Part numbers can be indicated by a

number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part

that has not been assigned a formal part number at time of
publication.

A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.

PAGE 6 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

“Make/Obtain Locally”

purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.

“Not Sold Separately”

purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.

- Indicates that the part can be

- Indicates that an item cannot be

WM-90S/P MIXER — SUGGESTED SPARE PARTS

WM-90P/S PLASTER AND MORTAR MIXER 1 TO 3
UNITS WITH HONDA GX240K1HA2 ENGINE

Qty. ... P/N ...................... Description

6 ....... 505834 ................ V-BELT A36 HONDA ENGINE

6 ....... 491112 ................ V-BELT A40 ELECTRIC MOTOR

2 ....... EM914288 ........... OIL SEAL, AXLE

4 ....... EM903113 ........... BEARING, CONE, AXLE

4 ....... EM903112 ........... BEARING, CUP, AXLE

2 ....... 20654-001 ........... SEAL, PADDLE SHAFT (BLACK)

2 ....... 530029 ................ RING, RETENTION

2 ....... 20104-002 ........... SEAL, SHAFT URETHANE (YELLOW)

3 ....... 17210ZE2515 ...... ELEMENT, AIR CLEANER

3 ....... 9807956846 ......... SPARK PLUG

1 ....... 28462ZE2W11 ..... ROPE, RECOIL STARTER

1 ....... 17620ZH7023 ...... CAP, FUEL TANK

2 ....... EM200863 ........... KIT, WIPER BLADES (STEEL DRUM)

2 ....... EM204625 ........... KIT, WIPER BLADES (PLASTIC DRUM)

NOTE

Part numbers on this
Suggested Spare Parts List
may supercede/replace the P/
N's shown in the test pages of
this manual.

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 7

NAMEPLATE AND DECALS

WM-90S/P MIXER — NAMEPLATE AND DECALS

PAGE 8 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — NAMEPLATE AND DECALS

NAMEPLATE AND DECALS

NO PART NO PART NAME QTY. REMARKS

1 DCL151 DECAL, TOWING INSTRUCTIONS 2
2 EM948630 DECAL, PUSH TO STOP 1
3 CIPDCL160 DECAL, CRUSH WARNING 2
4 515275 DECAL, WHITEMAN LOGO (SMALL) 3
5 504713 DECAL, SAFETY INSTRUCTIONS 1
6 35137 DECAL, WARNING READ 1
7 504714 DECAL, WHITEMAN LOGO (LARGE) 3
9 513479 DECAL, WARNING SAFETY GRATE 1
9 DCL335 DECAL, CRUSH WARNING SAFETY GRATE 1
10 DCL280 DECAL, WARNING DUMP HANDLE 1
11 513522 DECAL, DRUM LOCK 1
12 13118 DECAL, POWDER COATED 1

13 NAMEPLATE........................................................ 1 ......... CONTACT PARTS DEPT.

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 9

FRAME ASSY.

WM-90S/P MIXER — FRAME ASSY.

PAGE 10 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — FRAME ASSY.

FRAME ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 514842 LOCK PIN UNIT 1
2 491692 COTTER PIN 1
3 530023 SPRING LOCKING PIN 1
4 507444 WASHER, FLAT 3/4" 1
5 514835 MAIN FRAME 1
8 EM963692 BOLT 1/2" UNC 1-1/2" 6
9 492584 NUT, LOCK 1/2" 6
10 514802 AXLE, UNIVERSAL 1
11 10176 LOCK NUT 1/2" NC 1
12 EM124 BOLT 1/2"-13 X 4 G5 1
13

*

14
14

14A*516580 CLEVIS SAFETY HOOK ............................................ 1 ...................AFTER JANUARY 2006

15 13363KIT CHAIN AND LINK KIT ................................................. 1 ...................INCLUDES ITEMS W/

16 HBC-1 BALL HITCH 2-INCH ................................................... 1 ...................CONTACT UNIT SALES

17 HLC-1 LOOP HITCH .............................................................. 1 ................... CONTACT UNIT SALES

18 HPC-1 PIN HITCH 1-INCH ...................................................... 1 ................... CONTACT UNIT SALES

01004 CONNECTOR LINK ..................................................... 2 ................... BEFORE JANUARY 2006

*

01004 CONNECTOR LINK ..................................................... 1 ................... AFTER JANUARY 2006

*

SAFETY CHAIN 1

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 11

PADDLE SHAFT ASSY.

WM-90S/P MIXER — PADDLE SHAFT ASSY.

PAGE 12 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — PADDLE SHAFT ASSY.

PADDLE SHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 514752 PADDLE SHAFT 1
2 492584 NUT, LOCK 1/2" 6
3 EM200295 PADDLE ARM, CENTER ENGINE END 1
4 510721 BOLT, 1/2 " X 6" G5 2
5 EM200292 INSERT, PADDLE ARM 4
6 EM200296 PADDLE ARM, ENGINE END 1
7 504322 WASHER, FLAT 1/2" 6
8 EM200297 U-BOLT, END PADDLES 2
9 EM200294 PADDLE ARM, CENTER TOW END 1
10

# 492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14

*

11

# EM923023 WASHER, FLAT 5/16" 28

*

12# EM507519 BLADE, SIDE, POLY .................................................. 4 ................... PLASTIC DRUM

12
13
14
15
16 EM200293 PADDLE ARM, TOW END 1
17

18# EM507518 BLADE, PLASTIC END .............................................. 4 ................... PLASTIC DRUM

18

19 EM200863 KIT, WIPERS, SCRAPPERS & HDWARE................... 1 ...................INCLUDES ITEMS W/

19 EM204625 KIT, WIPERS, SCRAPPERS & HDWARE................... 1 ...................INCLUDES ITEMS W/#

EM200212 BLADE, SIDE, RUBBER ............................................. 4 ...................STEEL DRUM

*

# EM203432 BLADE, SIDE, SCRAPPER ........................................ 4 ...................STEEL & PLASTIC DRUM

*

# 2105164 NUT, HEX 5/16" NC G5 14

*

# EM923343 WASHER, LOCK 5/15" 14

*

# EM203433 BLADE ,SCRAPPER END .......................................... 4 ................... STEEL & PLASTIC DRUM

*

EM200213 BLADE, RUBBER END ............................................... 4 ................... STEEL DRUM

*

STEEL DRUM

PLASTIC DRUM

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 13

STEEL DRUM ASSY.

WM-90S/P MIXER — STEEL DRUM ASSY.

PAGE 14 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — STEEL DRUM ASSY.

STEEL DRUM ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 530028 DRUM BEARING BRACKET 2
2 3249 CAP, DUST 1

3 20561-001 BEARING SEALED ........................................... 2 ........... SET SCREWS AND BEARING

.......................................................................................... COLLAR CANNOT BE PURCHASED

.......................................................................................... SEPARATELY.

4 491008 CAP, GREASE FITTING 2
5 EM916019 FITTING, GREASE 2
6 EM969013 NUT, LOCK 3/8" 12
7 3019092 WASHER, FLAT 3/8" 4
8 514778 TRUNNION HUB 2
9 513453 ROLL PIN 3/16" X 3/4" 2
10 20654-001 SEAL, SHAFT (BLACK) 2
11 530029 RING, RETENTION 2
12 20104-002 SEAL, SHAFT URETHANE (YELLOW) 2
13 504943 BOLT, FHCS 3/8" NC X 2" G5 8
14 514786 DRUM, STEEL 1
15 492484 SET SCREW 2
16 530043 MAIN GEAR 1
17 501016 KEY, 3/8" X 88 MM 1
18 17985-012 CARRIAGE BOLT 3/8-16 X 1-1/2" 4
19 514752 SHAFT, PADDLE 1
20 492600 WASHER, FLAT 1/2" 4
21 514945 LIFT BAR 1
22 EM925191 PIN, COTTER 1
23 514946 GRATE 1
24 505070 PIN, COTTER 2
25 492556 HEX NUT 1/2" G5 2
26 6109180 WASHER, LOCK 1/2" 2
27 EM963692 BOLT 1/2" UNC 1-1/2" 2
28 EM963102 CAPSCREW, HHCS 1/2" NC X 1-1/4" 1
29 492584 NUT, LOCK1/2" NC 1
30 201537 HANDLE DUMP 1
31 EM98195 GRIP, DUMP HANDLE 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 15

PLASTIC DRUM ASSY.

WM-90S/P MIXER — PLASTIC DRUM ASSY.

PAGE 16 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — PLASTIC DRUM ASSY.

PLASTIC DRUM ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 530028 DRUM BEARING BRACKET 2
2 3249 CAP, DUST 1

3 20561-001 BEARING SEALED ........................................... 2 ........... SET SCREWS AND BEARING

.......................................................................................... COLLAR CANNOT BE PURCHASED

.......................................................................................... SEPARATELY.

4 491008 CAP, GREASE FITTING 2
5 EM916019 FITTING, GREASE 2
6 EM969013 NUT, LOCK 3/8" 20
7 3019092 WASHER, FLAT 3/8" 6
8 514778 TRUNNION HUB 2
9 513453 ROLL PIN 3/16" X 3/4" 2
10 20654-001 SEAL, SHAFT (BLACK) 2
11 530029 RING, RETENTION 2
12 20104-002 SEAL, SHAFT URETHANE (YELLOW) 2
13 504943 BOLT, FHCS 3/8" NC X 2" G5 8
14 515052 DRUM, PLASTIC 1
15 492484 SET SCREW 2
16 530043 MAIN GEAR 1
17 500432 KEY, 3/8" X 88 MM 1
18 17985-012 CARRIAGE BOLT 3/8-16 X 1-1/2" 4
19 514752 SHAFT, PADDLE 1
20 492600 WASHER, FLAT 1/2" 1
21 514947 LIFT BAR 1
22 EM925191 PIN, COTTER 1
23 EM507417 GRATE, MOVEABLE 1
24 505070 PIN, COTTER 2
25 492556 HEX NUT 1/2" G5 2
26 6109180 WASHER, LOCK 1/2" 2
27 EM963610 BOLT 3/8" NC 1-1/4" G8 2
28 EM963102 CAPSCREW, HHCS 1/2" NC X 1-1/4" 1
29 492584 NUT, LOCK1/2" NC 1
30 EM201537 HANDLE DUMP 1
31 EM98195 GRIP, DUMP HANDLE 1
32 515033 RUBBER, GASKET 1
33 511910 BOLT 1/4" NC X 1-1/4" G5 8
34 2101428 NUT 1/4" NC 8
35 514989 U-SUPPORT PLASTIC DRUM 1
36 EM507416 GRATE, STATIONARY 1
37 0401450160 WASHER, FLAT 5/8" 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 17

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)

PAGE 18 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)

NO. PART NO. PART NAME QTY. REMARKS

1 516064 DRUM AND SHAFT COMPLETE ASSY. ........... 1 ........... INCLUDES ITEMS LISTED BELOW:

530028 DRUM BEARING BRACKET 2
3249 CAP, DUST 1
20561-001 BEARING SEALED 2
491008 CAP, GREASE FITTING 2
EM916019 FITTING, GREASE 2
EM969013 NUT, LOCK 3/8" 20
3019092 WASHER, FLAT 3/8" 6
514754 TRUNNION HUB 2
513453 ROLL PIN 3/16" X 3/4" 2
20654-001 SEAL, SHAFT (BLACK) 2
530029 RING, RETENTION 2
20104-002 SEAL, SHAFT URETHANE (YELLOW) 2
513452 BOLT 3/8" NC X 1/4" G5 8
515052 DRUM, PLASTIC 1
492484 SET SCREW 2
530043 MAIN GEAR 1
500432 KEY, 3/8" X 50 MM 1
EM963057 CAPSCREW HHCS 3/8 X 1-1/2" 4
514752 SHAFT, PADDLE 1
EM507417 GRATE, MOVEABLE 1
505070 PIN, COTTER 2
492556 HEX NUT 1/2" G5 2
6109180 WASHER, LOCK 1/2" 2
EM963610 BOLT 3/8" NC 1-1/4" G8 2
EM201537 HANDLE, DUMP 1
15081 GRIP, DUMP HANDLE 1
515033 RUBBER, GASKET 1
511910 BOLT 1/4" NC X 1-1/4" G5 8
2101428 NUT 1/4" NC 8
514989 U-SUPPORT PLASTIC DRUM 1
EM507416 GRATE, STATIONARY 1
514752 PADDLE SHAFT 1
492584 NUT, LOCK 1/2" 6
EM200295 PADDLE ARM, CENTER ENGINE END 1
510721 BOLT, 1/2 " X 6" G5 2
EM200292 INSERT, PADDLE ARM 4
EM200296 PADDLE ARM, ENGINE END 1
504322 WASHER, FLAT 1/2" 6
EM200297 U-BOLT, END PADDLES 2
EM200294 PADDLE ARM, CENTER TOW END 1
492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14
EM923023 WASHER, FLAT 5/16" 28
13352 BLADE, SIDE, POLY 4
EM203432 BLADE, SIDE, SCRAPPER 4
2105164 NUT, HEX 5/16" NC G5 14
EM923343 WASHER, LOCK 5/15" 14
EM200293 PADDLE ARM, TOW END 1
EM203433 BLADE ,SCRAPPER END 4
507518 BLADE, PLASTIC END 4

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 19

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (STEEL DRUM)

PAGE 20 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (STEEL DRUM)

NO. PART NO. PART NAME QTY. REMARKS

1 516063 DRUM AND SHAFT COMPLETE ASSY. ........... 1 ........... INCLUDES ITEMS LISTED BELOW:

530028 DRUM BEARING BRACKET 2
3249 CAP, DUST 1
20561-001 BEARING SEALED 2
491008 CAP, GREASE FITTING 2
EM916019 FITTING, GREASE 2
EM969013 NUT, LOCK 3/8" 12
3019092 WASHER, FLAT 3/8" 4
514754 TRUNNION HUB 2
513453 ROLL PIN 3/16" X 3/4" 2
20654-001 SEAL, SHAFT (BLACK) 2
530029 RING, RETENTION 2
20104-002 SEAL, SHAFT URETHANE (YELLOW) 2
504943 BOLT 3/8" NC X 2" G5 8
514786 DRUM, STEEL 1
492484 SET SCREW 2
530043 MAIN GEAR 1
500432 KEY, 3/8" X 50 MM 1
EM963057 CAPSCREW HHCS 3/8 X 1-1/2" 4
514752 SHAFT, PADDLE 1
492600 WASHER, FLAT 1/2" 2
514946 GRATE 1
505070 PIN COTTER 2
492556 HEX NUT 1/2" G5 2
6109180 WASHER, LOCK 1/2" 2
EM963692 BOLT 1/2" UNC 1-1/2" 2
EM201537 HANDLE DUMP 1
15081 GRIP, DUMP HANDLE 1
514752 PADDLE SHAFT 1
492584 NUT, LOCK 1/2" 6
EM200295 PADDLE ARM, CENTER ENGINE END 1
510721 BOLT, 1/2 " X 6" G5 2
EM200292 INSERT, PADDLE ARM 4
EM200296 PADDLE ARM, ENGINE END 1
504322 WASHER, FLAT 1/2" 6
EM200297 U-BOLT, END PADDLES 2
EM200294 PADDLE ARM, CENTER TOW END 1
492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14
EM923023 WASHER, FLAT 5/16" 28
EM200212 BLADE, SIDE, RUBBER 4
EM203432 BLADE, SIDE, SCRAPPER 4
2105164 NUT, HEX 5/16" NC G5 14
EM923343 WASHER, LOCK 5/15" 14
EM200293 PADDLE ARM, TOW END 1
EM203433 BLADE ,SCRAPPER END 4
EM200213 BLADE, RUBBER END 4

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 21

AXLE ASSY.

WM-90S/P MIXER — AXLE ASSY.

12

10

8

9

11

1

NOTES:

COMPLETE HUB ASSEMBLY INCLUDES

1

ITEMS WITHIN DASHED LINES, AND ALSO
INCLUDES ITEMS 1 AND 2.

9

8

5

7

3

6

4

2

1

PAGE 22 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — AXLE ASSY.

AXLE ASSY.

NO PART NO PART NAME QTY. REMARK

1# 3469 DUST CAP 2
2# 8115 LUG NUTS 8
3 3005 TIRE AND RIM, CARLISE 2
4 8164 ARMLE NUT 1" 2
5 491688 COTTER PIN 1/8" X 1-1/2' 2
6 EM511159 WASHER, FLAT, .087" THICKNESS 2
7 EM501299 WASHER, FLAT, .135" THICKNESS 1
8# EM903113 BEARING CONE, (1-1/16" SPINDLE) 4
9# EM903012 BEARING CUP 4
10# EM914288 OIL SEAL 2

11 EM941306 HUB ASSY., 4-BOLT (1-1/16" SPINDLE) ........................ 2 ........... INCLUDES ITEMS W/#

12 514802 AXLE, UNIVERSAL 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 23

ENGINE ASSY.

WM-90S/P MIXER — ENGINE ASSY.

PAGE 24 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — ENGINE ASSY.

ENGINE ASSY.

NO PART NO PART NAME QTY. REMARKS

1 492583 NUT 3/8" NC G5 8
2 506488 FLAT WASHER 3/8 8
3 EM905016 PILLOW BLOCK BEARING 2
4 492378 BOLT 3/8" NC X 1-3/4" G5 4
5 490957 RING, RETENTION 2
6 513868 PINION GEAR 1
7 500214 KEY, 1/4" X 30 MM 1

8 EM502226 PINION SHAFT .......................................... 1 ................ REPLACES P/N 502226

9 492057 PULLEY (LARGE) 1
10 505084 KEY, 1/4" X 55 MM 1
11 492467 SET SCREW, 5/16' NC 3/8" 4
12 505834 V-BELT, A-36 2
13 503117 BOLT, 3/8" NC X 3" G5 1
14 90745ZE2600 SQ. KEY 6.3 X 6.3 X 43 MM 1
15 492378 BOLT 3/8" NC X 1-3/4" G5 4
16 GX240K1HA2 ENGINE, HONDA 1
17 515040 BELT RETAINER BAR 1
18 EM901074 PULLEY, (SMALL) 1
22 492598 WASHER, FLAT 3/8" 5
23 492624 WASHER, LOCK 3/8" 4
24 492554 NUT, HEX 3/8" 4
25 492600 WASHER, FLAT 1/2" 1
26 505084 SQ. KEY, 1/4" X 55 MM 1
27 492394 BOLT 1/2" NC X 1-1/2" G5 1
28 EM102014 SPRING, EXTENSION 1
29 EM203098 SPRING CLIP 1
30 492313 BOLT 3/8" NC X 1-1/2" G5 3
31 EM507491 ARM, IDLER 1
32 959080 ROD-END 2
33 492584 NUT, HEX 1/2" 1
34 492574 NUT, HEX 3/8" NF G5 2
35 492476 SET SCREW, 5/16' NC 3/4" 1
36 EM901515 PULLEY, IDLER 1
37 515045 ROD 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 25

ELECTRIC MOTOR ASSY.

WM-90S/P MIXER — ELECTRIC MOTOR ASSY.

PAGE 26 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — ELECTRIC MOTOR ASSY.

ELECTRIC MOTOR ASSY.

NO PART NO PART NAME QTY. REMARKS

1 492583 NUT 3/8" NC G5 8
2 506488 FLAT WASHER 3/8 8
3 EM905016 PILLOW BLOCK BEARING 2
4 492378 BOLT 3/8" NC X 1-3/4" G5 4
5 490957 RING, RETENTION 2
6 513868 PINION GEAR 1
7 500214 KEY, 1/4" X 30 MM 1
8 20216-001 PINION SHAFT 1
9 505204 PULLEY (LARGE) 1
10 505084 KEY, 1/4" X 55 MM 1
11 492467 SET SCREW, 5/16' NC 3/8" 4
12 507725 V-BELT, A-48 2
13 503117 BOLT, 3/8" NC X 3" G5 1
15 492378 BOLT 3/8" NC X 1-3/4" G5 4
16 EM939315 ELECTRIC MOTOR 3.0 HP 1
17 515040 BELT RETAINER BAR 1
18 EM901513 PULLEY, (SMALL) 1
22 492598 WASHER, FLAT 3/8" 5
23 492624 WASHER, LOCK 3/8" 4
24 492554 NUT, HEX 3/8" 4
25 492600 WASHER, FLAT 1/2" 1
26 505084 KEY, 1/4" X 55 MM 1
27 492394 BOLT 1/2" NC X 1-1/2" G5 1
28 EM102014 SPRING, EXTENSION 1
29 EM203098 SPRING CLIP 1
30 492313 BOLT 3/8" NC X 1-1/2" G5 3
31 EM507491 ARM, IDLER 1
32 959080 ROD-END 2
33 492584 NUT, HEX 1/2" 1
34 492574 NUT, HEX 3/8" NF G5 2
35 492476 SET SCREW, 5/16' NC 3/4" 1
36 EM901515 PULLEY, IDLER 1
37 515045 ROD 1
38 492364 BOLT, 5/16" NC X 1" G5 1
39 492554 NUT, HEX 3/8" 4
40 EM507715 BELT RETAINER BAR 1
41 500214 KEY, 1/4" X 30 MM 1
42 490957 RING, RETENTION 2

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 27

CABINET ASSY.

WM-90S/P MIXER — CABINET ASSY.

PAGE 28 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — CABINET ASSY.

CABINET ASSY.

NO PART NO PART NAME QTY. REMARKS

1 514964 CABINET, ENGINE W/DECALS .................. 1 ........... INCLUDES ITEMS W/

2 490202 RUBBER PROTECTOR 4

3 13287 LOCK NUT 8-32 ........................................... 6 ........... REPLACEMENT PART ONLY

4 2203 WASHER, FLAT #10 .................................... 6 ........... REPLACEMENT PART ONLY

5 1307 SCREW RHMS 8-32 X 1/2" ......................... 6 ........... REPLACEMENT PART ONLY

6

*

7 492375 BOLT 3/8" NC X 1" G5 4
8 492598 WASHER, FLAT 3/8" 4
9 492583 NUT 3/8" NC G5 4
10 29174-001 KNOB, MUSHROOM 1
11 29173-001 SWITCH, PUSH-PULL 1
12 504135C WIRE HARNESS 1
13 EM974007 PAINT, SPRAY 12 OZ. TRAFFIC RED 1

491010 LATCH ASSY., COMPLETE 2

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 29

AIR CLEANER ASSY.

HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.

PAGE 30 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — AIR CLEANER ASSY.

AIR CLEANER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 16271ZE2000 GASKET, ELBOW ..................................... 1 ............. INCLUDES ITEM W/

2 17210ZE2515 ELEMENT, AIR CLEANER, DUAL 1
3
5 17231ZH9820 COVER, AIR CLEANER 1
6 17232891000 GROMMET, AIR CLEANER 1
8 # 17238ZE2310 COLLAR, AIR CLEANER 2
9 # 17239ZE1000 COLLAR B, AIR CLEANER 1

10 17410ZE2020 ELBOW COMP., AIR CLEANER ............... 1 ............. INCLUDES ITEM W/#

12 0037806000 WINGNUT 6MM 1
13 90325044000 WINGNUT, TOOL BOX SETTING 2
14 90009ZE2003 BOLT- WASHER 6 X 22 1
15 9405006000 NUT, FLANGE 6MM 2

17218ZE2505 FILTER, OUTER 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 31

CAMSHAFT ASSY.

HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.

PAGE 32 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CAMSHAFT ASSY.

CAMSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 14100ZE2W01 CAMSHAFT ASSY. ................................... 1 ............. INCLUDES ITEM W/

1 14100ZE2306 CAMSHAFT 1
2 14410ZE2013 ROD PUSH 2
3 14431ZE2010 ARM VALVE ROCKER 2
4 14441ZE2000 LIFTER VALVE 2
5 14451ZE1013 PIVOT ROCKER ARM 2
6
7 14711ZE2000 VALVE, IN. 1
8 14721ZE2000 VALVE, EX. 1
9 14751ZE2003 SPRING, VALVE 2
10 14771ZE2000 RETAINER, IN. VALVE SPRING 1
11 14773ZE2000 RETAINER, EX. VALVE SPRING 1
12 14781ZE2000 ROTATOR, VALVE 1
13 14791ZE2010 PLATE, PUSH ROD GUIDE 1
14 90012ZE0010 BOLT, PIVOT 8MM 2
15 90206ZE1000 NUT, PIVOT ADJ. 2

14568ZE1000 SPRING, WEIGHT RETURN 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 33

CARBURETOR ASSY.

HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.

PAGE 34 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CARBURETOR ASSY.

CARBURETOR ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1

+ 16010ZE2812 GASKET SET 1

*

2
3
5
6
7
8
9
10
11
12
13
14 16211ZE2000 INSULATOR, CARB. 1
15 16220ZA0702 SPACER COMP., CARB. 1
16 16221ZA0800 GASKET, CARBURETOR 1
17 16223ZA0800 GASKET, INSULATOR 1
18 16610ZE1000 LEVER COMP., CHOKE, STD. 1
19
20
21
22
23
24
25 9430520122 PIN, SPRING 2 X 12 1
26
26
26
27
28

16011ZA0931 VALVE SET, FLOAT 1

*

16013ZA0931 FLOAT SET 1

*

16016ZHW01 SCREW SET 1

*

+ 16024ZE1811 SCREW SET, DRAIN 1

*

+ 16028ZE0005 SCREW SET B 1

*

16028ZE2005 CHOKE SET 1

*

16100ZE2W71 CARBURETOR ASSY. ................... 1 ..... INCLUDES ITEMS W/

*

16124ZE0005 SCREW, THROTTLE STOP 1

*

16166ZE2W70 NOZZLE, MAIN 1

*

16075GHBB00 COLLAR, SET 1

*

16075GHBB00 O-RING 1

*

16953ZE1812 LEVER, VALVE 1

*

16954ZE1811 PLATE, LEVER SETTING 1

*

16956ZE1811 SPRING, VALVE LEVER 1

*

16957ZE1812 GASKET, VALVE 1

*

16967ZE0811 CUP, FUEL STRAINER 1

*

93500030060H SCREW, PAN 3 X 6 2

*

99101ZH70820 JET, MAIN #82, OPTIONAL 1

*

99101ZH70850 JET, MAIN #85, OPTIONAL 1

*

99101ZH80880 JET, MAIN #88 1

*

99204ZE20400 JET SET, PILOT #40 1

*

16015ZE8005 CHAMBER SET, FLOAT ................ 1 ..... INCLUDES ITEMS W/+

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 35

CONTROL ASSY.

HONDA GX240K1HA2 ENGINE — CONTROL ASSY.

PAGE 36 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CONTROL ASSY.

CONTROL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 16551ZE2000 ARM, GOVERNOR 1
3 16555ZE2000 ROD, GOVERNOR 1
4 16561ZE2000 SPRING, GOVERNOR 1
5 16571ZE2000 SPRING, THROTTLE RETURN 1

8 16570ZE2W00 CONTROL ASSEMBLY ................................ 1 .......... INCLUDES ITEMS W/

10
11
12
14
15
16
19 90013883000 BOLT, FLANGE (6 X 12) (CT200) 2
20 90015ZE5010 BOLT, GOVERNOR ARM 1
21
24
27 9405006000 NUT, FLANGE 1

16571ZE2W00 LEVER, CONTROL 1

*

16574ZE1000 SPRING, LEVER 1

*

16575ZE2W00 WASHER, CONTROL LEVER 1

*

16578ZE1000 SPACER, CONTROL LEVER 1

*

16581ZE2W00 BASE, CONTROL 1

*

16584883300 SPRING, CONTROL ADJUSTING 1

*

90114SA0000 NUT, SELF- LOCK (6MM) 1

*

93500050280A SCREW, PAN (5 X 28) 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 37

HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.

CRANKCASE COVER ASSY.

PAGE 38 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CRANKCASE COVER ASSY.

CRANKCASE COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

2 11400ZE2621 COVER ASSY., CRANKCASE ..................... 1 ........... INCLUDES ITEMS W/

(H- TYPE) (BALANCER)
3 11381ZE2801 GASKET, CASE COVER 1

4 15600ZG4003 CAP ASSY., OIL FILLER ............................. 1 ........... INCLUDES ITEMS W/#

5 15600735003 CAP ASSY., OIL FILLER ............................. 1........... INCLUDES ITEMS W/%

8% 15625ZE1003 GASKET, OIL FILLER CAP 1
9# 15625ZE1003 GASKET, OIL FILLER CAP 1

10 16510ZE2811 GOVERNOR ASSEMBLY (BALANCER) ...... 1........... INCLUDES ITEMS W/+

11

+ 16511ZE2000 WEIGHT, GOVERNOR 2

*

12

+ 16512ZE2811 HOLDER, GOVERNOR WEIGHT 1

*

13

+ 16513ZE2000 PIN, GOVERNOR WEIGHT 2

*

14
15
16
17 90701HC4000 PIN, DOWEL (8 X 12) 2
18
19 957010803500 BOLT, FLANGE (8 X 35) 7
20
21
22
23

16531ZE2000 SLIDER, GOVERNOR 1

*

90473147000 WASHER (6 X 16) 1

*

90602ZE1000 CLIP, GOVERNOR HOLDER 1

*

58176 WASHER, PLAIN (6MM) 1

*

961006202000 BEARING, RADIAL BALL (6202) 1

*

961006204000 BEARING, RADIAL BALL (6204) 1

*

961006206000 BEARING, RADIAL BALL (6206) 1

*

961006302000 BEARING, RADIAL BALL (6302) 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 39

CRANKSHAFT ASSY.

HONDA GX240K1HA2 ENGINE — CRANKSHAFT ASSY.

PAGE 40 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CRANKSHAFT ASSY.

CRANKSHAFT ASSY.

NO. PART NO. PART NAME QTY. REMARKS

3 13320ZE2611 CRANKSHAFT (L- TYPE) ............................. 1 .......... INCLUDES ITEM W/

8 13351ZE2010 WEIGHT BALANCER 1
12

961006206000 BEARING, RADIAL BALL (6206) 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 41

HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.

CYLINDER BARREL ASSY.

PAGE 42 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CYLINDER BARREL ASSY.

CYLINDER BARREL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 12000ZE2834 CYLINDER ASSY., BALANCER + OIL ALERT ...... 1 .......... INCLUDES ITEMS W/

2 15510ZE2043 SWITCH ASSY., OIL LEVEL 1
3 16541ZE2010 SHAFT, GOVERNOR ARM 1
6 90131896650 BOLT, DRAIN PLUG 2
7 90446KE1000 WASHER 8.2 X17X0.8 1
8
9 91353671003 O-RING 14MM ARAI 1
10 9405010000 NUT FLANGE 10MM 1
11 031112230 WASHER, DRAIN PLUG 12MM 2
12 9425110000 PIN, LOCK 10MM 1
13 957010601200 BOLT, FLANGE 6X12 2
14
15 90013883000 BOLT, FLANGE 6X12 CT200 1
16 34150ZH7003 ALERT UNIT, OIL 1

91201890003 OIL SEAL 30X46X8 1

*

961006202000 BEARING, RADIAL BALL 6202 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 43

CYLINDER HEAD ASSY.

HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.

PAGE 44 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — CYLINDER HEAD ASSY.

CYLINDER HEAD ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 12200ZH9000 CYLINDER HEAD COMP. ....................................... 1 .......... INCLUDES ITEMS W/

2
3
4
5 12251ZE2800 GASKET, CYLINDER HEAD 1
6 12310ZE2020 COVER COMP., HEAD 1
7 12391ZE2020 GASKET, CYLINDER HEAD COVER 1
8 14775ZE2010 SEAT, VALVE SPRING 1
10 90014ZE2000 BOLT, HEAD COVER 1
11 90042ZE2000 BOLT, STUD 8X123 2
12 92900080320E BOLT, STUD 8X47 2
13 90441ZE2010 WASHER COMP., HEAD COVER 1
14 9430112200 PIN A, DOWEL 12X20 2
15 950051100130M BULK HOSE, VACUUM 11X1000, 11X100 1
16 957011008000 BOLT, FLANGE 10X80 4
17 9807956846 SPARK PLUG, BPR6ES, NGK 1
17 9807956855 SPARK PLUG, W20EPR-U, DENSO 1

12204ZE2306 GUIDE, VALVE, OS, OPTIONAL 1

*

12205ZE2305 GUIDE, EX. VALVE, OS, OPTIONAL 1

*

12216ZE2300 CLIP, VALVE GUIDE 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 45

FAN COVER ASSY.

HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.

PAGE 46 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — FAN COVER ASSY.

FAN COVER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 16731ZE2003 CLIP, TUBE 1
2 19610ZE2010ZC COVER COMP., FAN *NH1* BLACK 1
3 19631ZE2D00 SHROUD 1
4 32197ZH8003 SUB-HARNESS 1
5 36100ZE1015 SWITCH ASSY., ENGINE STOP 1
7 90013883000 BOLT, FLANGE 6X12, CT200 6
9 90684ZA0601 CLIP, WIRE HARNESS 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 47

FLYWHEEL ASSY.

HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.

PAGE 48 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — FLYWHEEL ASSY.

FLYWHEEL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 19511ZE2000 FAN, COOLING 1
2 28450ZE2W11 PULLEY COMP., STARTER, SCREEN GRID 1
4 31100ZE2010 FLYWHEEL COMP. 1
7 90201ZE3V00 NUT, SPECIAL 16MM 1
8 90741ZE2000 KEY, SPECIAL WOODRUFF 25X18 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 49

MUFFLER ASSY.

HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.

PAGE 50 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — MUFFLER ASSY.

MUFFLER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 18310ZE2W00 MUFFLER 1
2 18320ZE2W01 PROTECTOR, MUFFLER 1
3 18323ZE2W00 PROTECTOR, EX. PIPE 1
4 18330ZE2W00 PIPE, EX. 1
5 18331ZE2810 CAP, MUFFLER 1
6 18333ZK6Y00 GASKET, EX. PIPE 1
7 18355ZE2010 ARRESTER, SPARK 1
8 18381ZE2W10 GASKET, MUFFLER (ARRESTER) 1
9 18381ZE2800 GASKET, MUFFLER 1
10 90013883000 BOLT, FLANGE (6 X 12) (CT200) 1
11 90050ZE1000 SCREW, TAPPING (5 X 8) 6
12 90055ZE1000 SCREW, TAPPING (4 X 6) 3
13 90050ZE1000 SCREW, TAPPING (5 X 8) (OPTIONAL) 1
14 9405008000 NUT, FLANGE (8MM) 5

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 51

FUEL TANK ASSY.

HONDA GX240K1HA2 ENGINE — FUEL TANK ASSY.

PAGE 52 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — FUEL TANK ASSY.

FUEL TANK ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 16854ZH8000 RUBBER SUPPORTER 107MM 1
2 16955ZE1000 JOINT, FUEL TANK 1
3 17510ZE2010ZD TANK COMP., FUEL *NH1*, BLACK 1

5 17620ZH7023 CAP COMP., FUEL FILLER .................................... 1 .......... INCLUDES ITEMS W/

6
8 17672ZE2W01 FILTER, FUEL 1
11 91353671003 O-RING 14MM, ARAI 1
12 9405008000 NUT, FLANGE 8MM 2
13 950014500360M BULK HOSE, FUEL 4.5X3000, 4.5X222 1
14 9500202080 CLIP, TUBE, B8 2
15 957010802500 BOLT, FLANGE 8X25 2

17631ZH7003 GASKET, FUEL FILLER CAP 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 53

IGNITION COIL ASSY.

HONDA GX240K1HA2ENGINE — IGNITION ASSY.

PAGE 54 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2ENGINE — IGNITION ASSY.

IGNITION COIL ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 30500ZF6W02 COIL ASSY., IGNITION 1
2 30700ZE1013 CAP ASSY., NOISE SUPPRESSOR 1
6 31512ZE2000 GROMMET, WIRE 1
8 36101ZE1010 WIRE, STOP SWITCH 370MM 1
11 90015883000 BOLT, FLANGE 6X28 2

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 55

PISTON ASSY.

HONDA GX240K1HA2 ENGINE — PISTON ASSY.

PAGE 56 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — PISTON ASSY.

PISTON ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 13010ZE2013 RING SET, PISTON, STD. 1
1 13011ZE2013 RING SET, PISTON, OS 0.25, OPTIONAL 1
1 13012ZE2013 RING SET, PISTON, OS 0.50, OPTIONAL 1
1 13013ZE2013 RING SET, PISTON, 0.75, OPTIONAL 1
2 13101ZE2W00 PISTON, STANDARD 1
2 13102ZE2W00 PISTON, OS 0.25, OPTIONAL 1
2 13103ZE2W00 PISTON, OS 0.50, OPTIONAL 1
2 13104ZE2W00 PISTON, 0.75, OPTIONAL 1
3 13111ZE2000 PIN, PISTON 1

4 13200ZE2000 ROD ASSY., CONNECTING STANDARD ................ 1 .......... INCLUDES ITEMS W/

4 13200ZE2305 ROD ASSY., CONNECTING, US 0.25, OPT. 1
5
6 90551ZE1000 CLIP, PISTON PIN 18MM 2

90001ZE8000 BOLT, CONNECTING ROD 2

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 57

RECOIL STARTER ASSY.

HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.

PAGE 58 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — RECOIL STARTER ASSY.

RECOIL STARTER ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 28400ZE2W01ZB STARTER ASSY., RECOIL *NH1*, BLK ............... 1 ......... INCLUDES ITEMS W/

2
3
4
5
6
7
8
10
11
13
14 90008ZE2003 BOLT, FLANGE 6X10 3

28410ZE2W01ZB CASE COMP., RECOIL STARTER *NH1*, BLK 1

*

28421ZE2W01 PULLEY, RECOIL STARTER 1

*

28422ZE2W01 RATCHET, STARTER 2

*

28441ZE2W01 SPRING, FRICTION 1

*

28442ZE2W01 SPRING, STARTER RETURN 1

*

28443ZE2W01 SPRING RATCHET 2

*

28444ZE2W01 RETAINER, SPRING 1

*

28461ZE2W02 GRIP, STARTER 1

*

28462ZE2W11 ROPE, RECOIL STARTER 1

*

90004ZE2W01 SCREW, CENTER 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 59

HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.

GEAR REDUCTION ASSY.

PAGE 60 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — GEAR REDUCTION ASSY.

GEAR REDUCTION ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 11500ZE2620 COVER ASSY, REDUCTION CASE ............. 1 .......... INCLUDES ITEMS W/

2 11521ZE2800 GASKET, CHAIN CASE COVER 1
3 22103ZE2620 GEAR, PRIMARY DRIVE (17T) 1
4 23220ZE2621 COUNTERSHAFT 1
5 23710ZE2621 SHAFT, P.T.O. (H- TYPE) 1
6 90401ZE2620 SHIM A (OPTIONAL) AR
7 90402ZE2620 SHIM B (OPTIONAL) AR
8 90473842000 WASHER (8MM) 1
9 90745ZE2600 KEY (6.3 X 6.3 X 43) 1
10
11 9430108140 PIN A, DOWEL ( 8 X 14) 2
12 957010802500 BOLT, FLANGE (8 X 25) 1
13 957010804000 BOLT, FLANGE (8 X 40) 6
14
15

91201890003 OIL SEAL (30 X 46 X 8) 1

*

961006206000 BEARING, RADIAL BALL (6206) 1

*

961006302000 BEARING, RADIAL BALL (6302) 1

*

*

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 61

LABEL ASSY.

HONDA GX240K1HA2 ENGINE — LABEL ASSY.

PAGE 62 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

HONDA GX240K1HA2 ENGINE — LABEL ASSY.

LABELS ASSY.

NO. PART NO. PART NAME QTY. REMARKS

1 87521ZE2W01 EMBLEM, INTERNAL 1
2 87522ZE1810 MARK, CAUTION, EXTERNAL 1
3 87522ZH9000 LABEL, CAUTION 1
5 87528ZE2810 MARK, CHOKE, EXTERNAL 1
15 87586ZH7W00 LABEL, FUEL CAUTION 1
16 87532ZH8810 MARK, OIL ALERT 1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 63

TERMS AND CONDITIONS OF SALE — PARTS

PAYMENT TERMS

Terms of payment for parts are net 30 days.

FREIGHT POLICY

All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.

MINIMUM ORDER

The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.

RETURNED GOODS POLICY

Return shipments will be accepted and credit
will be allowed, subject to the following provi­sions:

1. A Returned Material Authorization must
be approved by Multiquip prior to ship­ment.

2. To obtain a Return Mater ial Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quanti­ties, and descriptions of the items to be
returned.

a. The parts numbers and descriptions

must match the current parts price
list.

b. The list must be typed or computer

generated.

c. The list must state the reason(s) for

the return.

d. The list must reference the sales

order(s) or invoice(s) under which the
items were originally purchased.

e. The list must include the name and

phone number of the person request­ing the RMA.

3. A copy of the Return Material Authoriza­tion must accompany the return shipment.

4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.

5. Parts must be in new and resalable con-

6. The following items are not returnable:

7. The sender will be notified of any material

8. Such material will be held for five working

9. Credit on returned parts will be issued at

10. In cases where an item is accepted, for

11. Credit issued will be applied to future

PRICING AND REBATES

Prices are subject to change without prior
notice. Price changes are effective on a spe­cific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.

Multiquip reserves the right to quote and sell
dition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.

a. Obsolete parts. (If an item is in the

price book and shows as being re­placed by another item, it is obsolete.)

b. Any parts with a limited shelf life

(such as gaskets, seals, “O” rings,
and other rubber parts) that were pur­chased more than six months prior to
the return date.

c. Any line item with an extended dealer

net price of less than $5.00.

d. Special order items.
e. Electrical components.

f. Paint, chemicals, and lubricants.

g. Decals and paper products.

h. Items purchased in kits.

received that is not acceptable.

days from notification, pending instruc­tions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.

dealer net price at time of the original
purchase, less a 15% restocking charge.

which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.

purchases only.

direct to Government agencies, and to Original

Equipment Manufacturer accounts who use

our products as integral parts of their own

products.

SPECIAL EXPEDITING SERVICE

A $35.00 surcharge will be added to the invoice

for special handling including bus shipments,

insured parcel post or in cases where Multiquip

must personally deliver the parts to the carrier.

LIMITATIONS OF SELLER’S LIABILITY

Multiquip shall not be liable hereunder for

damages in excess of the purchase price of the

item with respect to which damages are

claimed, and in no event shall Multiquip be

liable for loss of profit or good will or for any

other special, consequential or incidental dam-

ages.

LIMITATION OF WARRANTIES

No warranties, express or implied, are made

in connection with the sale of parts or trade

accessories nor as to any engine not manufac-

tured by Multiquip. Such warranties made in

connection with the sale of new, complete units

are made exclusively by a statement of war-

ranty packaged with such units, and Multiquip

neither assumes nor authorizes any person to

assume for it any other obligation or liability

whatever in connection with the sale of its

products. Apart from such written statement of

warranty, there are no warranties, express,

implied or statutory, which extend beyond the

description of the products on the face hereof.

Effective: February 22, 2006

PAGE 64 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)PAGE 64 — WHITEMAN G-4.5R A.C. GENERATOR— OPERATION & PARTS MANUAL — REV. #0 (12/15/03)

NOTE PAGE

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 65

PARTS MANUAL

HERE'S HOW TO GET HELP

PLEASE HAVE THE MODEL AND SERIAL

NUMBER

UNITED STATES

Multiquip Corporate Office MQ Parts Department

18910 Wilmington Ave. Tel. [phone] Fax: [phone]
Carson, CA 90746 Fax [phone] Fax: [phone]
Contact: [e-mail]

Mayco Parts Warranty Department

800-306-2926 Fax: [phone], Ext. 279 Fax: [phone]
310-537-3700 Fax: [phone], Ext. 279

Service Department Technical Assistance

800-421-1244 Fax: [phone] Fax: [phone]
310-537-3700

ON-HAND

WHEN CALLING

^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668

MEXICO UNITED KINGDOM

MQ Cipsa Multiquip (UK) Limited Head Office

Carr. Fed. Mexico-Puebla KM 126.5 Tel: [phone] Hanover Mill, Fitzroy Street, Tel: [phone]
Momoxpan, Cholula, Puebla 72760 Mexico Fax: [phone] Ashton-under-Lyne, Fax: [phone]
Contact: [e-mail] Lancashire OL7 0TL

Contact: [e-mail]

CANADA BRAZIL

Multiquip Multiquip

4110 Industriel Boul. Tel: [phone] Av. Evandro Lins e Silva, 840 - grupo 505 Tel: [phone]
Laval, Quebec, Canada H7L 6V3 Fax: [phone] Barra de Tijuca - Rio de Janeiro Fax: [phone]

Contact: [e-mail] Contact: [e-mail], [e-mail]

© COPYRIGHT 2008, MULTIQUIP INC.

Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the
property of their respective owners and used with permission.

This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.

The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data
contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or
the information published in this publication at any time without notice and without incurring any obligations.

Your Local Dealer is: