THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 21728
WARNING
SILICOSIS WARNINGRESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
WARNING
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 3
Terms And Conditions Of Sale ................................ 64
PAGE 4 — HTN 31V
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 4
Effective: June 1st, 2005
Ordering parts has never been easier!
HTN 27K-28K— PARTS ORDERING PROCEDURES
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
■
View Parts Diagrams
■
Order Parts
■
Print Specification Information
Goto www.multiquip.com and click on
Order Par ts
to log in and save!
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Order via Phone:
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
parts@multiquip.com.
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the
internet
Standard orders
on
complete part numbers.*
Fax
your order in and qualify for a 3% Discount
on
Standard orders
complete part numbers.*
Domestic (US) Dealers Call:
1-800-427-1244
and qualify for a 5% Discount
for all orders which include
for all orders which include
International Customers
their local Multiquip Representatives for
Parts Ordering information.
Note: Discounts Are Subject To Change
Note: Discounts Are Subject To Change
should contact
When ordering parts, please supply:
❒❒
❒
Dealer Account Number
❒❒
❒❒
❒
Dealer Name and Address
❒❒
❒❒
❒
Shipping Address (if different than billing address)
❒❒
❒❒
❒
Return Fax Number
❒❒
❒❒
❒
Applicable Model Number
❒❒
❒❒
❒
Quantity, Part Number and Description of Each Part
❒❒
NOTE
www.multiquip.com
Unless otherwise indicated by customer, all orders are treated as
within 24 hours. We will make every effort to ship
if received prior to 2PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 5
❒❒
❒
Specify Preferred Method of Shipment:
❒❒
✓
Fed Ex/UPS
■
■
■ Next Day
■
Stock Orders
✓ DHL
Priority One
Ground
Second/Third Day
✓
Tr u ck
Standard Orders
Air Shipments
must be noted on fax or web order form.
the same day the order is received,
and will ship
HTN 27K-28K— EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
The contents and part numbers listed in the parts section are
subject to change
guarantee the availibility of the parts listed.
Sample Parts List:
NO.PART NO.PART NAMEQTY. REMARKS
112345BOLT ....................... 1 .... INCLUDES ITEMS W/
2
*
2*12347WASHER, 3/8 IN. .... 1....
312348HOSE .................... A/R .. MAKE LOCALLY
412349BEARING ................ 1 .... S/N 2345B AND ABOVE
NO. Column
Unique Symbols - All items with same unique symbol
, #, +, %, or >) in the number column belong to the same
(
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
NOTE
without notice
WASHER, 1/4 IN. ...........
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
. Multiquip does not
NOT SOLD SEPARATELY
MQ-45T ONLY
QTY. Column
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
*
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break
range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
- All items on the parts list with the same unique
- Used to list an effective serial number
- Indicates that the part is used
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 6 — HTN 31V
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 6
“Make/Obtain Locally”
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
“Not Sold Separately”
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
- Indicates that the part can be
- Indicates that an item cannot be
HTN 27K-28K— SUGGESTED SPARE PARTS
HTN 27K/28K KOHLER ENGINES
1 Unit
Qty.P/NDescription
421495 ............TROWEL ARM, LH
42829 ..............TROWEL ARM, RH
411903 ............LEVER TROWEL ARM (L.S.)
411904 ............LEVER TROWEL ARM (R.S.)
220938 ............THRUST COLLAR KIT
212785 ............SPIDER KIT
200166 A ........... WASHER
201876 ..............JAM NUT
200164 B ........... SCREW
411039 ............BUSHING
411595 ............SPRING (L.S.)
411594 ............SPRING (R.S.)
201875 .............. WASHER
201322 .............. SCREW ASSY, ARM RETAINING
201162 A ........... CAP GREASE FITTING
40131 A ........... SCREW (HHC 1/4 - 20 X 3/4)
40948 .............. WASHER, FLAT
120138 ............BELT, DRIVE CVT
200181 B ........... WASHER 1/4 IN
111418 ............FUEL CAP/GAUGE (ENG)
119633 ............BUSHING, RUBBER FUEL
12124 ..............CABLE, THROTTLE (FOOT PEDAL)
12153 ..............ROD END, FEM RH (THROTTLE CABLE)
611143 ............ROD END, FEM RH 1/2 - 20 (STEERING)
42063 ..............ROD END, MALE RH 3/8 - 24 (STEERING)
211142 ............ROD END, MALE RH 1/2 - 20 (STEERING)
4......................BLADE ASSY. CONTACT UNIT SALES DEPT/ ACCESSORY ITEM
35+%2367SET COLLAR .................................................... 1 ............ INCLUDES ITEM W/
36+%■0685SCREW, SHS 5/16 - 18 X 5/161
37+%0126KEY, WOODRUFF #91
38+10511SHAFT, PITCH CONTROL, LH TPC ................. 1 ............ LEFT SIDE ONLY
39%10510SHAFT, PITCH CONTROL, RH TPC ................. 1 ............ RIGHT SIDE ONLY
40+%1733WASHER, 1/32 X 1/2 HARDENED4
41+%2007SHAFT1
42+%1578KEY, WOODRUFF, #31
43+%11654PIN, ROLL 1/8 X 1 PLATED1
44+%2311SPACER, 3/4 X 1/2 X 0.8L1
45+%11583U-JOINT, PITCH CONTROL1
46+%1586PIN, ROLL 1/8 X 3/41
47+%12365SHAFT, PITCH CONTROL1
48+10722SLIDE BLOCK, LH PITCH CONTROL .............. 1 ............ LEFT SIDE ONLY
49 %10721SLIDE BLOCK, RH PITCH CONTROL .............. 1 ............ RIGHT SIDE ONLY
50+%10382BOLT, SHOULDER 3/8 X 3/8 LONG1
51+%10723PIN, SPIROL 3/16 X 1 3/8 HD1
52+%12460CABLE, PITCH ASSEMBLY1
53+%1116NUT, BRASS JAM 5/16 –182
NOTE: INDICATED QUANTITIES ARE FOR ONE PITCH TOWER. IF ORDERING FOR TWO PITCH TOWERS DOUBLE QUANTITY.
■
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 21
EZ-MOVER ASSEMBLY -- PURCHASE THROUGH MQ UNIT SALES DEPT.
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 63
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
1.A Returned Material Authorization (RMA)
must be approved by Multiquip prior to
shipment.
2.To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items to
be returned.
a.The parts numbers and descriptions
must match the current parts price
list.
b.The list must be typed or computer
generated.
c.The list must state the reason(s) for
the return.
d.The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.The list must include the name and
phone number of the person
requesting the RMA.
3.A copy of the Return Material
Authorization must accompany the return
shipment.
4.Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.Parts must be in new and resalable
6.The following items are not returnable:
7.The sender will be notified of any material
8.Such material will be held for five working
9.Credit on returned parts will be issued at
10. In cases where an item is accepted for
11. Credit issued will be applied to future
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand at
the time of any price change.
PRICING AND REBATES
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
a.Obsolete parts. (If an item is in the
price book and shows as being replaced by another item, it is obsolete.)
b.Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.Any line item with an extended dealer
net price of less than $5.00.
d.Special order items.
e.Electrical components.
f.Paint, chemicals, and lubricants.
g.Decals and paper products.
h.Items purchased in kits.
received that is not acceptable.
days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
dealer net price at time of the original
purchase, less a 15% restocking charge.
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
purchases only.
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand at
the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer (OEM) accounts who
use our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of the
item with respect to which damages are claimed,
and in no event shall Multiquip be liable for loss
of profit or good will or for any other special,
consequential or incidental damages.
LIMITATION OF WARRANTIES
No warranties, expressed or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty, there
are no warranties, expressed, implied or
statutory, which extend beyond the description
of the products on the face hereof.
PAGE 64 — HTN 31V
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 64
HTN 27K-28K—NOTES
HTN 27K-28K • RIDE-ON POWER TROWEL — PARTS MANUAL — REV. #0 (05/12/06) — PAGE 65
Multiquip Inc, the MQ logo and the MQ Whiteman logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission.
All other trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the HTN 27K/28K Ride-On Power
Tr ow e l. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves
the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.