Multiquip EM-70P, EM-70S User Manual
PARTS MANUAL
SERIES
MODELS
EM-70S (STEEL)
EM-70P (PLASTIC)
PLASTER AND MORTAR MIXER
(GASOLINE ENGINE/ELECTRIC MOTOR)
Revision #8 (03/19/10)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING
Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingand otherconstruction activities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of thesechemicals are:
Leadfromlead-based paints.
Crystallinesilica from bricks.
Cementand othermasonry products.
Arsenicandchromium fromchemically
treatedlumber.
Your risk from these exposures varies,
dependingon howoften youdo this type
of work. To reduce your exposure to
these chemicals: work in aALWAYS
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
PAGE 2 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
NOTES
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 3
EM-70 S/P PLASTER/MORTAR MIXER — TABLE OF CONTENTS
MQ-ESSICK — EM-70S/P
Plaster/Mortar Mixer
Proposition 65 Warning ............................................ 2
Table Of Contents .................................................... 4
Parts Ordering Procedures ...................................... 5
Explanation of Code In Remarks Column................ 6
Suggested Spare Parts ............................................ 7
Component Drawings
Nameplate and Decals.......................................... 8-9
Frame Assembly ............................................... 10-11
Paddle Shaft Assembly ..................................... 12-13
Steel Drum Assembly........................................14-15
Plastic Drum Assembly .....................................16-17
Drum & Paddle Shaft Complete Assy. (Poly) ..... 18-19
Drum & Paddle Shaft Complete Assy. (Steel) ...20-21
Axle Assembly ...................................................22-23
Engine Assembly .............................................. 24-25
Electric Motor Assembly.................................... 26-27
Cabinet Assembly ............................................. 28-29
Specifications and are
NOTE
subject to change
without notice.
HONDA GX160K1HX2 ENGINE
Air Cleaner Assy. .............................................. 30-31
Camshaft Assy. ................................................ 32-33
Carburetor Assy. .............................................. 34-35
Control Assy. .................................................... 36-37
Crankcase Cover Assy. .................................... 38-39
Crankshaft Assy. .............................................. 40-41
Cylinder Barrel Assy. ........................................ 42-43
Cylinder Head Assy. ......................................... 44-45
Fan Cover Assy. ............................................... 46-47
Flywheel Assy. .................................................. 48-49
Fuel Tank Asssembly ....................................... 50-51
Ignition Coil Asssembly .................................... 52-53
Muffler Asssembly ............................................ 54-55
Piston Rings Asssembly ................................... 56-57
Recoil Starter Asssembly ................................. 58-59
1/6 Gear Reduction Asssembly ....................... 60-61
Labels Asssembly ............................................ 62-63
HONDA GX240K1HA2 ENGINE
Air Cleaner Assembly........................................64-65
Camshaft Assembly ..........................................66-67
Carburetor Assembly ........................................68-69
Control Assembly .............................................. 70-71
Crankcase Cover Assembly ..............................72-73
Crankshaft Assembly ........................................74-75
Cylinder Barrel Assembly .................................. 76-77
Cylinder Head Assembly ...................................78-79
Fan Cover Assembly ......................................... 80-81
Flywheel Assembly ...........................................82-83
Muffler Assembly .............................................. 84-85
Fuel Tank Assembly .......................................... 86-87
Ignition Coil ....................................................... 88-89
Piston Assembly ................................................ 90-91
Recoil Starter ....................................................92-93
Gear Reduction Assembly ................................94-95
Label Assembly .................................................96-97
Terms and Conditions of Sale ................................ 98
PAGE 4 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
January 1
Effective:
st
, 2006
Best Deal!
Order via Internet (Dealers Only):
Order parts on-line using Multiquip’s SmartEquip website!
N View Parts Diagrams
N Order Parts
N Print Specification Information
Goto www.multiquip.com and click on
Order Par ts
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
to log in and save!
Order via Phone:
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
R Dealer Account Number
R Dealer Name and Address
R Shipping Address (if different than billing address)
R Return Fax Number
R Applicable Model Number
R Quantity, Part Number and Description of Each Part
www.multiquip.com
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 5
When ordering parts, please supply:
R Specify Preferred Method of Shipment:
UPS/Fed Ex DHL
N Priority One Tr uck
N Ground
N Next Day
N Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip
does not guarantee the availability of the parts listed.
SAMPLE PARTS LIST
NO. PART NO. PART NAME QTY. REMARKS
1 12345 BOLT ......................1 .....INCLUDES ITEMS W/%
2% WASHER, 1/4 IN. ...........NOT SOLD SEPARATELY
2% 12347 WASHER, 3/8 IN. ...1 .....MQ-45T ONLY
3 12348 HOSE ..................A/R ...MAKE LOCALLY
4 12349 BEARING ..............1 .....S/N 2345B AND ABOVE
NO. Column
Unique Symbols — All items with same unique
symbol
QTY. Column
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
Assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Duplicate Item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
PART NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables, shims,
and certain washers and nuts.
“Not Sold Separately” — Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
PAGE 6 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— SUGGESTED SPARE PARTS
EM-70P/S PLASTER AND MORTAR MIXER 1 TO 3
UNITS WITH HONDA GX160K1HX2 AND GX240K1HA2
ENGINES
Qty. ... P/N ...................... Description
6 ....... 508473 ................ V-BELT A37 HONDA ENGINE, 5.0 HP
6 ....... 505834 ................ V-BELT A36 HONDA ENGINE, 8.0 HP
6 ....... 491112 ................ V-BELT A40 ELECTRIC MOTOR
2 ....... EM914288 ........... OIL SEAL, AXLE
4 ....... EM903113 ........... BEARING, CONE, AXLE
4 ....... EM903112 ........... BEARING, CUP, AXLE
4 ....... 507844 ................ SPRING COMPRESSION
4 ....... EM200285 ........... GLAND, PACKING HALF
12 ..... EM200301 ........... RING, SHAFT PACKING
4 ....... 505065 ................ CARRIAGE BOLT 3/8" NC X 3" (STEEL)
3 ....... 17210ZE2515 ...... ELEMENT, AIR CLEANER
3 ....... 9807956846 ......... SPARK PLUG
1 ....... 28462ZE2W11 ..... ROPE, RECOIL STARTER
1 ....... 17620ZH7023 ...... CAP, FUEL TANK
2 ....... EM203010 ........... KIT, WIPER BLADES (STEEL DRUM)
2 ....... EM204624 ........... KIT, WIPER BLADES (PLASTIC DRUM)
NOTE
Part numbers on this
Suggested Spare Parts List
may supercede/replace the P/
N's shown in the test pages of
this manual.
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 7
NAMEPLATE AND DECALS
EM-70 S/P MIXER— NAMEPLATE AND DECALS
PAGE 8 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO PART NO PART NAME QTY. REMARKS
1 DCL151 DECAL, TOWING INSTRUCTIONS 2
2 EM948630 DECAL, PUSH TO STOP 1
3 CIPDCL160 DECAL, CRUSH WARNING 2
4 EM510891 DECAL, ESSICK LOGO (SMALL) 3
5 948501 DECAL, SAFETY INSTRUCTIONS 1
6 35137 DECAL, WARNING READ 1
7 EM510883 DECAL, ESSICK LOGO (LARGE) 3
9 513479 DECAL, WARNING SAFETY GRATE 1
9 DCL335 DECAL, CRUSH WARNING SAFETY GRATE 1
10 DCL280 DECAL, WARNING DUMP HANDLE 1
11 513522 DECAL, DRUM LOCK 1
12 13118 DECAL, POWDER COATED 1
13 948121 DECAL, SELF-ADJUSTING SEALS 1
14 NAMEPLATE ........................................................ 1 ......... CONTACT PARTS DEPT.
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 9
FRAME ASSY.
EM-70 S/P MIXER— FRAME ASSY.
PAGE 10 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— FRAME ASSY.
FRAME ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 514842 LOCK PIN UNIT 1
2 491692 COTTER PIN 1
3 530023 SPRING LOCKING PIN 1
4 507444 WASHER, FLAT 3/4" 1
5 514835 MAIN FRAME 1
7 514836 HANDLE, CLUTCH ENGAGE 1
8 EM963692 BOLT 1/2" UNC 1-1/2" 6
9 492584 NUT, LOCK 1/2" 6
10 514802 AXLE, UNIVERSAL 1
11 10176 LOCK NUT 1/2" NC 1
12 EM124 BOLT 1/2"-13 X 4 G5 1
13
*
14
14
14A*516580 CLEVIS SAFETY HOOK ............................................ 1 ...................AFTER JANUARY 2006
15 13363KIT CHAIN AND LINK KIT ................................................. 1 ...................INCLUDES ITEMS W/
16 HBC-1 BALL HITCH 2-INCH ................................................... 1 ...................CONTACT UNIT SALES
17 HLC-1 LOOP HITCH .............................................................. 1 ................... CONTACT UNIT SALES
18 HPC-1 PIN HITCH 1-INCH...................................................... 1 ...................CONTACT UNIT SALES
01004 CONNECTOR LINK ..................................................... 2 ................... BEFORE JANUARY 2006
*
01004 CONNECTOR LINK ..................................................... 1 ...................AFTER JANUARY 2006
*
SAFETY CHAIN 1
*
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 11
PADDLE SHAFT ASSY.
EM-70 S/P MIXER— PADDLE SHAFT ASSY.
PAGE 12 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— PADDLE SHAFT ASSY.
PADDLE SHAFT ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 514753 PADDLE SHAFT 1
2 492584 NUT, LOCK 1/2" 6
3 EM202896 PADDLE ARM, CENTER ENGINE END 1
4 EM963110 BOLT, 1/2-13 X 3-3/4 2
5 EM200292 INSERT, PADDLE ARM 4
6 EM202898 PADDLE ARM, ENGINE END 1
7 504322 WASHER, FLAT 1/2" 6
8 EM200297 U-BOLT, END PADDLES 2
9 EM202897 PADDLE ARM, CENTER TOW END 1
10
# 492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14
*
11
# EM923023 WASHER, FLAT 5/16" 28
*
12# EM507497 BLADE, SIDE, POLY .................................................. 4 ...................PLASTIC DRUM
12
13
14
15
16 EM202899 PADDLE ARM, TOW END 1
17
18# EM507496 BLADE, PLASTIC END .............................................. 4 ...................PLASTIC DRUM
18
19 EM203010 KIT, WIPERS, SCRAPPERS & HDWARE ................... 1 ...................INCLUDES ITEMS W/
19 EM204624 KIT, WIPERS, SCRAPPERS & HDWARE ................... 1 ...................INCLUDES ITEMS W/#
EM202929 BLADE, SIDE, RUBBER ............................................. 4 ................... STEEL DRUM
*
# EM202928 BLADE, SIDE, SCRAPPER ........................................ 4 ................... STEEL & PLASTIC DRUM
*
# 2105164 NUT, HEX 5/16" NC G5 14
*
# EM923343 WASHER, LOCK 5/15" 14
*
# EM202927 BLADE, SCRAPPER END .......................................... 4 ................... STEEL & PLASTIC DRUM
*
EM202926 BLADE, RUBBER END ............................................... 4 ...................STEEL DRUM
*
STEEL DRUM
PLASTIC DRUM
*
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 13
EM-70 S/P MIXER— STEEL DRUM ASSY.
STEEL DRUM ASSY.
4
3
1
5
31
13
24
20
14
36
15
15
17
1
3
6
7
16
23
22
20
36
12
20
26
25
30
13
34
35
8
27
29
11
10
9
21
20
28
8
35
33
34
6
2
1
18
PART OF
FRONT FRAME
7
32
19
12
33
32
9
10
11
18
PART OF
REAR FRAME
NOTES:
SET SCREWS AND BEARING
1
COLLAR ARE INCLUDED WITH
BEARING AND CANNOT BE
PURCHASED SEPARATELY.
PAGE 14 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— STEEL DRUM ASSY.
STEEL DRUM ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 530028 DRUM BEARING BRACKET 2
2 3249 CAP, DUST 1
3 20561-001 BEARING SEALED ........................................... 2 ........... SET SCREWS AND BEARING
.......................................................................................... COLLAR CANNOT BE PURCHASED
.......................................................................................... SEPARATELY.
4 491008 CAP, GREASE FITTING 2
5 EM916019 FITTING, GREASE 2
6 EM969013 NUT, LOCK 3/8" 12
7 3019092 WASHER, FLAT 3/8" 4
8 507844 SPRING, COMPRESSION 4
9 EM200288 PLATE, PACKING GLAND PRESSURE 2
10 EM200285 GLAND, PACKING HALF 4
11 EM200301 RING, SHAFT PACKING 12
12 EM200303 FOLLOWER, PACKING RING 2
13 EM966048 CARRIAGE BOLT 3/8" NC X 1-1/4" 8
14 514745 DRUM, STEEL 1
15 EM961019 SET SCREW 2
16 530043 MAIN GEAR 1
17 501016 KEY, 3/8" X 88 MM 1
18 17985-012 CARRIAGE BOLT 3/8-16 X 1-1/2" 4
19 514753 SHAFT, PADDLE 1
20 492600 WASHER, FLAT 1/2" 4
21 514986 LIFT BAR 1
22 EM925191 PIN, COTTER 1
23 514962 GRATE 1
24 505070 PIN, COTTER 2
25 492556 HEX NUT 1/2" G5 2
26 6109180 WASHER, LOCK 1/2" 2
27 EM963692 BOLT 1/2" UNC 1-1/2" 2
28 EM963102 CAPSCREW, HHCS 1/2" NC X 1-1/4" 1
29 492584 NUT, LOCK1/2" NC 1
30 EM201537 HANDLE DUMP 1
31 EM98195 GRIP, DUMP HANDLE 1
32 EM969012 NUT, STOP 8
33 514760 DRUM HEAD 2
34 EM200287 ADJUSTABLE NUT, 3/8" 4
35 0401450160 WASHER, FLAT 5/8" 4
36 EM200286 CARRIAGE BOLT 3/8" NC X 3" 4
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 15
PLASTIC DRUM ASSY.
EM-70 S/P MIXER— PLASTIC DRUM ASSY.
23
22
37
6
36
NOTES:
SET SCREWS AND BEARING
1
COLLAR ARE INCLUDED WITH
BEARING AND CANNOT BE
PURCHASED SEPARATELY.
4
6
3
1
5
7
45
32
43
44
27
10
29
6
46
11
12
21
20
28
9
8
34
18
47
13
35
38
39
6
7
14
33
40
30
31
42
41
15
15
2
1
18
PART OF
FRONT FRAME
PAGE 16 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
19
12
17
1
45
3
18
32
6
7
16
45
43
8
9
10
11
PART OF
REAR FRAME
EM-70 S/P MIXER— PLASTIC DRUM ASSY.
PLASTIC DRUM ASSY.
NO. PART NO. PART NAME QTY. REMARKS
1 530028 DRUM BEARING BRACKET 2
2 3249 CAP, DUST 1
3 20561-001 BEARING SEALED ................................................... 2 ............ SET SCREWS AND BEARING
................................................................................................... COLLAR CANNOT BE PURCHASED
................................................................................................... SEPARATELY.
4 491008 CAP, GREASE FITTING 2
5 EM916019 FITTING, GREASE 2
6 EM969013 NUT, LOCK 3/8" 20
7 3019092 WASHER, FLAT 3/8" 6
8 507844 SPRING, COMPRESSION 4
9 EM200288 PLATE, PACKING GLAND PRESSURE 2
10 EM200285 GLAND, PACKING HALF 4
11 EM200301 RING, SHAFT PACKING 12
12 EM200303 FOLLOWER, PACKING RING 2
13 506900 SUPPORT BRACKET 2
14 EM506311 DRUM, PLASTIC 1
15 EM961019 SET SCREW 2
16 530043 MAIN GEAR 1
17 501016 KEY, 3/8" X 88 MM 1
18 17985-012 CARRIAGE BOLT 3/8-16 X 1-1/2" 4
19 514753 SHAFT, PADDLE 1
20 492600 WASHER, FLAT 1/2" 1
21 514987 LIFT BAR 1
22 EM925191 PIN, COTTER 1
23 504535 GRATE, MOVEABLE 1
24 505070 PIN, COTTER 2
25 492556 HEX NUT 1/2" G5 2
26 6109180 WASHER, LOCK 1/2" 2
27 EM963692 BOLT 1/2" UNC 1-1/2" 2
28 EM963102 CAPSCREW, HHCS 1/2" NC X 1-1/4" 1
29 492584 NUT, LOCK1/2" NC 1
30 EM201537 HANDLE DUMP 1
31 EM98195 GRIP, DUMP HANDLE 1
32 EM969012 NUT, STOP 8
33 511910 BOLT 1/4" NC X 1-1/4" G5 8
34 2101428 NUT 1/4" NC 8
35 515177 U-SUPPORT PLASTIC DRUM 1
36 504534 GRATE, STATIONARY 1
37 0401450160 WASHER, FLAT 5/8" 1
38 507512 CARRIAGE BOLT 3/8" NC X3- 1/2" 4
39 505196 CARRIAGE BOLT 3/8" NC X1- 1/2" G5 8
40 511910 BOLT 1/4" NC X1- 1/4" G5 8
41 981635 BOLT, HEX, 1/2"13 NC X 1 3
42 492584 NUT, LOCK 1/2" 3
43 EM200287 ADJUSTABLE NUT, 3/8" 4
44 0401450160 WASHER, FLAT 5/8" 4
45 514760 DRUM HEAD 2
46 EM200786 CARRIAGE BOLT 3/8" NC X 3" 4
47 EM966048 CARRIAGE BOLT 3/8" NC X 3/4" 8
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 17
EM-70 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)
PAGE 18 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)
NO. PART NO. PART NAME QTY. REMARKS
1 516066 DRUM AND SHAFT COMPLETE ASSY. .................. 1 ............ INCLUDES ITEMS LISTED BELOW:
530028 DRUM BEARING BRACKET 2
3249 CAP, DUST 1
20561-001 BEARING SEALED 2
491008 CAP, GREASE FITTING 2
EM916019 FITTING, GREASE 2
EM969013 NUT, LOCK 3/8" 8
3019092 WASHER, FLAT 3/8" 2
507844 SPRING, COMPRESSION 2
EM200288 PLATE, PACKING GLAND PRESSURE 2
EM200285 GLAND, PACKING HALF 2
EM200301 RING, SHAFT PACKING 2
EM200303 FOLLOWER, PACKING RING 2
506900 SUPPORT BRACKET 2
EM506311 DRUM, PLASTIC 1
EM961019 SET SCREW 2
530043 MAIN GEAR 1
501016 KEY, 3/8" X 88 MM 1
EM963057 CAPSCREW HHCS 3/8 X 1-1/2" 4
514753 SHAFT, PADDLE 1
504535 GRATE, MOVEABLE 1
505070 PIN COTTER 2
492556 HEX NUT 1/2" G5 2
6109180 WASHER, LOCK 1/2" 2
EM963692 BOLT 1/2" UNC 1-1/2" 2
EM963102 CAPSCREW, HHCS 1/2" NC X 1-1/4" 1
EM201537 HANDLE DUMP 1
EM98195 GRIP, DUMP HANDLE 1
EM969012 NUT, STOP 8
511910 BOLT 1/4" NC X 1-1/4" G5 8
2101428 NUT 1/4" NC 8
515177 U-SUPPORT PLASTIC DRUM 1
504534 GRATE, STATIONARY 1
507512 CARRIAGE BOLT 3/8" NC X3- 1/2" 4
505196 CARRIAGE BOLT 3/8" NC X1- 1/2" G5 8
511910 BOLT 1/4" NC X1- 1/4" G5 8
981635 BOLT, HEX, 1/2"13 NC X 1 3
492584 NUT, LOCK 1/2" 3
EM200287 ADJUSTABLE NUT, 3/8" 4
0401450160 WASHER, FLAT 5/8" 4
514760 DRUM HEAD 2
514753 PADDLE SHAFT 1
492584 NUT, LOCK 1/2" 6
EM202896 PADDLE ARM, CENTER ENGINE END 1
510721 BOLT, 1/2 " X 6" G5 2
EM200292 INSERT, PADDLE ARM 4
EM202898 PADDLE ARM, ENGINE END 1
504322 WASHER, FLAT 1/2" 6
EM200297 U-BOLT, END PADDLES 2
EM202897 PADDLE ARM, CENTER TOW END 1
492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14
EM923023 WASHER, FLAT 5/16" 28
EM507497 BLADE, SIDE, POLY 4
EM202899 BLADE, SIDE, SCRAPPER 4
2105164 NUT, HEX 5/16" NC G5 14
EM923343 WASHER, LOCK 5/15" 14
EM202899 PADDLE ARM, TOW END 1
EM202927 BLADE, SCRAPPER END 4
EM507496 BLADE, PLASTIC END 4
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 19
EM-70 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY. (STEEL DRUM)
PAGE 20 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.
DRUM AND PADDLE SHAFT COMPLETE ASSY. (STEEL DRUM)
NO. PART NO. PART NAME QTY. REMARKS
1 516065 DRUM AND SHAFT COMPLETE ASSY. ........... 1 ........... INCLUDES ITEMS LISTED BELOW:
530028 DRUM BEARING BRACKET 2
3249 CAP, DUST 1
20561-001 BEARING SEALED 2
491008 CAP, GREASE FITTING 2
EM916019 FITTING, GREASE 2
EM969013 NUT, LOCK 3/8" 12
3019092 WASHER, FLAT 3/8" 4
507844 SPRING, COMPRESSION 2
EM200288 PLATE, PACKING GLAND PRESSURE 2
EM200285 GLAND, PACKING HALF 2
EM200301 RING, SHAFT PACKING 2
EM200303 FOLLOWER, PACKING RING 2
505064 CARRIAGE BOLT 3/8" NC X 3/4" 8
514745 DRUM, STEEL 1
EM961019 SET SCREW 2
530043 MAIN GEAR 1
501016 KEY, 3/8" X 88 MM 1
EM963057 CAPSCREW HHCS 3/8 X 1-1/2" 4
514753 SHAFT, PADDLE 1
492600 WASHER, FLAT 1/2" 2
514962 GRATE 1
505070 PIN COTTER 2
492556 HEX NUT 1/2" G5 2
6109180 WASHER, LOCK 1/2" 2
EM963692 BOLT 1/2" UNC 1-1/2" 2
EM201537 HANDLE DUMP 1
EM98195 GRIP, DUMP HANDLE 1
EM969012 NUT, STOP 8
514760 DRUM HEAD 2
EM200287 ADJUSTABLE NUT, 3/8" 4
0401450160 WASHER, FLAT 5/8" 4
505065 CARRIAGE BOLT 3/8" NC X 3" 8
514753 PADDLE SHAFT 1
492584 NUT, LOCK 1/2" 6
EM202896 PADDLE ARM, CENTER ENGINE END 1
510721 BOLT, 1/2 " X 6" G5 2
EM200292 INSERT, PADDLE ARM 4
EM202898 PADDLE ARM, ENGINE END 1
504322 WASHER, FLAT 1/2" 6
EM200297 U-BOLT, END PADDLES 2
EM202897 PADDLE ARM, CENTER TOW END 1
492367 SCREW, HHC 5/16-18 X 1-3/4 G5 14
EM923023 WASHER, FLAT 5/16" 28
EM202929 BLADE, SIDE, RUBBER 4
EM202899 BLADE, SIDE, SCRAPPER 4
2105164 NUT, HEX 5/16" NC G5 14
EM923343 WASHER, LOCK 5/15" 14
EM202899 PADDLE ARM, TOW END 1
EM202927 BLADE, SCRAPPER END 4
EM202926 BLADE, RUBBER END 4
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 21
AXLE ASSY.
EM-70 S/P MIXER— AXLE ASSY.
12
10
8
9
11
1
NOTES:
COMPLETE HUB ASSEMBLY INCLUDES
1
ITEMS WITHIN DASHED LINES, AND ALSO
INCLUDES ITEMS 1 AND 2.
9
8
5
7
3
6
4
2
1
PAGE 22 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— AXLE ASSY.
AXLE ASSY.
NO PART NO PART NAME QTY. REMARK
1# 3469 DUST CAP 2
# 8115 LUG NUTS 8
2
3 3005 TIRE AND RIM, CARLISE .............................................. 2 ........... BEFORE JANUARY 2006
3 516476 TIRE AND RIM, TOWMASTER II ................................... 2 ........... AFTER JANUARY 2006
4 8164 ARMLE NUT 1" 2
5 491688 COTTER PIN 1/8" X 1-1/2' 2
6 EM511159 WASHER, FLAT, .087" THICKNESS 2
7 EM501299 WASHER, FLAT, .135" THICKNESS 1
8
# EM903113 BEARING CONE, 4
# EM903012 BEARING CUP 4
9
10# EM914288 OIL SEAL 2
11 EM941306 HUB ASSY., 4-BOLT ....................................................... 2 ........... INCLUDES ITEMS W/
12 514802 AXLE, UNIVERSAL 1
#
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 23
ENGINE ASSY.
EM-70 S/P MIXER— ENGINE ASSY.
PAGE 24 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 MIXER — ENGINE ASSY.
ENGINE ASSY.
NO PART NO PART NAME QTY. REMARKS
1 492583 NUT 3/8" NC G5 8
2 506488 FLAT WASHER 3/8 8
3 EM905016 PILLOW BLOCK BEARING 2
4 492378 BOLT 3/8" NC X 1-3/4" G5 4
5 490957 RING, RETENTION 1
6 513868 PINION GEAR 1
7 500214 KEY, 1/4" X 30 MM 1
8 EM502226 PINION SHAFT .......................................... 1 ................ REPLACES P/N 502226
9 492057 PULLEY (LARGE) 1
10 505084 KEY, 1/4" X 55 MM 1
11 492467 SET SCREW, 5/16' NC 3/8" 4
12 508473 V-BELT, A-37 .............................................. 2 ................ HONDA 5.5 HP
12 505834 V-BELT, A-36 .............................................. 2 ................ HONDA 8.0 HP
13 503117 BOLT, 3/8" NC X 3" G5 1
14 501019 SQ. KEY 3/16" X 45 MM 5.5 HP 1
14 90745ZE2600 SQ. KEY 6.3 X 6.3 X 43 MM 8.0 HP 1
15 492367 BOLT 5/16" NC X 1-3/4" G5 ....................... 4 ................ HONDA 5.5 HP
15 492378 BOLT 3/8" NC X 1-3/4" G5 ......................... 4 ................ HONDA 8.0 HP
16 GX160K1HX2 ENGINE, HONDA 5.5 HP 1
16 GX240K1HA2 ENGINE, HONDA 8.0 HP 1
17 515040 BELT RETAINER BAR 1
18 492055 PULLEY, (SMALL), 5.5 HP 1
18 EM901074 PULLEY, (SMALL), 8.0 HP 1
22 492597 WASHER, FLAT 5/16" ................................ 6 ................ HONDA 5.5 HP
22 492598 WASHER, FLAT 3/8" .................................. 6 ................ HONDA 8.0 HP
23 492623 WASHER, LOCK 5/16" ............................... 4 ................ HONDA 5.5 HP
23 492624 WASHER, LOCK 3/8" ................................. 4 ................ HONDA 8.0 HP
24 492553 NUT, HEX 5/16" .......................................... 4 ................ HONDA 5.5 HP
24 492554 NUT, HEX 3/8" ............................................ 4 ................ HONDA 8.0 HP
25 492600 WASHER, FLAT 1/2" 1
26 505084 SQ. KEY, 1/4" X 55 MM 1
27 492394 BOLT 1/2" NC X 1-1/2" G5 1
28 EM102014 SPRING, EXTENSION 1
29 EM203098 SPRING CLIP 1
30 492313 BOLT 3/8" NC X 1-1/2" G5 3
31 EM507713 ARM, IDLER............................................... 1 ................ HONDA 5.5 HP
31 EM507491 ARM, IDLER............................................... 1 ................ HONDA 8.0 HP
32 EM959080 ROD-END 2
33 492584 NUT, HEX 1/2" 1
34 492574 NUT, HEX 3/8" NF G5 2
35 492476 SET SCREW, 5/16' NC 3/4" 1
36 EM901515 PULLEY, IDLER 1
37 515299 ROD ........................................................... 1 ................ HONDA 5.5 HP
37 515045 ROD ........................................................... 1 ................ HONDA 8.0 HP
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 25
ELECTRIC MOTOR ASSY.
EM-70 S/P MIXER— ELECTRIC MOTOR ASSY.
PAGE 26 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— ELECTRIC MOTOR ASSY.
ELECTRIC MOTOR ASSY.
NO PART NO PART NAME QTY. REMARKS
1 492583 NUT 3/8" NC G5 8
2 506488 FLAT WASHER 3/8 8
3 EM905016 PILLOW BLOCK BEARING 2
4 492378 BOLT 3/8" NC X 1-3/4" G5 4
8 20216-001 SHAFT AND PINION 1
9 505204 PULLEY (LARGE) 1
10 505084 KEY, 1/4" X 55 MM 1
11 492467 SET SCREW, 5/16' NC 3/8" 4
12 507725 V-BELT, A-48 2
13 503117 BOLT, 3/8" NC X 3" G5 1
15 492378 BOLT 3/8" NC X 1-3/4" G5 4
16 35L229S302 ELECTRIC MOTOR 1.5 HP 1
17 515040 BELT RETAINER BAR 1
18 502213 PULLEY, (SMALL) 1
22 492598 WASHER, FLAT 3/8" 5
23 492624 WASHER, LOCK 3/8" 4
24 492554 NUT, HEX 3/8" 4
25 492600 WASHER, FLAT 1/2" 1
26 505084 KEY, 1/4" X 55 MM 1
27 492394 BOLT 1/2" NC X 1-1/2" G5 1
28 EM102014 SPRING, EXTENSION 1
29 EM203098 SPRING CLIP 1
30 492313 BOLT 3/8" NC X 1-1/2" G5 3
31 EM507491 ARM, IDLER 1
32 959080 ROD-END 2
33 492584 NUT, HEX 1/2" 1
34 492574 NUT, HEX 3/8" NF G5 2
35 492476 SET SCREW, 5/16' NC 3/4" 1
36 EM901515 PULLEY, IDLER 1
37 515045 ROD 1
38 492364 BOLT, 5/16" NC X 1" G5 1
39 492554 NUT, HEX 3/8" 4
40 515365 BELT RETAINER BAR 1
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 27
CABINET ASSY.
EM-70 S/P MIXER— CABINET ASSY.
PAGE 28 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
EM-70 S/P MIXER— CABINET ASSY.
CABINET ASSY.
NO PART NO PART NAME QTY. REMARKS
1 514948 CABINET, ENGINE W/DECALS .................. 1 ........... INCLUDES ITEMS W/
2 490202 RUBBER PROTECTOR 4
3 13287 LOCK NUT 8-32 ........................................... 6 ........... REPLACEMENT PART ONLY
4 2203 WASHER, FLAT #10 .................................... 6 ........... REPLACEMENT PART ONLY
5 1307 SCREW RHMS 8-32 X 1/2" ......................... 6 ........... REPLACEMENT PART ONLY
6
*
7 492375 BOLT 3/8" NC X 1" G5 4
8 492598 WASHER, FLAT 3/8" 4
9 492583 NUT 3/8" NC G5 4
10 29174-001 KNOB, MUSHROOM 1
11 29173-001 SWITCH, PUSH-PULL 1
12 504135C WIRE HARNESS 1
491010 LATCH ASSY., COMPLETE 2
*
EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10) — PAGE 29
AIR CLEANER ASSY.
HONDA GX160K1HX2 — AIR CLEANER ASSY.
PAGE 30 — EM-70 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #8 (03/19/10)
Loading...