Page 1
User Manual
4 CH H.264 Multiplex DVR
Page 2
I
This symbol is intended to alert the user to the presence of unprotected “Dangerous voltage"
within the product's enclosure that may be strong enough to cause a risk of electric shock.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
NOTE: This equipment has been tested and found to comply with the limits for a class digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at ones own expense.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
VER.:1.0, P/N: R040182A
Page 3
II
All the safety and operating instructions must be read before the unit is operated.
• Make sure to switch the power off before you install the DVR.
• There is the danger of an electric shock if the DVR is opened by an unqualified service
engineer or installer.
• Avoid using the DVR outside of the reference temperature and humidity indicated in the
specification.
• Avoid exposing the DVR to violent movement or vibration.
• Do not use or store the DVR in direct sunlight or near to any source of heat.
• Do not place any object into the holes used for air circulation.
• Always use the DVR in a well ventilated location to prevent overheating.
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
Page 4
III
TABLE OF CONTENTS
Chapter 1 FEATURES .........................................................................................................1
Chapter 2 PACKING DETAIL...............................................................................................2
Chapter 3 LOCATION AND CONTROL ...............................................................................3
3.1 Front Panel Controls...............................................................................................3
3.2 Real Panel Connectors...........................................................................................4
3.3 Remote Controller...................................................................................................5
3.4 Mouse Control ........................................................................................................7
3.5 Playback Mode .......................................................................................................9
3.6 PTZ Mode.............................................................................................................10
Chapter 4 INSTALLATION .................................................................................................12
4.1 System Configuration ...........................................................................................12
4.2 Hard Disk Installation............................................................................................13
Chapter 5 BASIC OPERATION and MENU SETUP ..........................................................15
5.1 Main Menu Setup..................................................................................................15
5.2 Record Setup........................................................................................................16
5.3 Event Setup ..........................................................................................................17
5.4 Schedule Setup ....................................................................................................19
5.5 Camera Setup.......................................................................................................20
5.6 Account Setup.......................................................................................................21
5.7 Network Setup ......................................................................................................22
5.8 PTZ & RS-485 Setup ............................................................................................25
5.9 System Setup .......................................................................................................26
5.10 Utility Setup.........................................................................................................30
5.11 Diagnostic ...........................................................................................................31
Chapter 6 SEARCH & BACKUP ........................................................................................32
6.1 Search Setup........................................................................................................32
6.2 Backup Setup .......................................................................................................35
Chapter 7 SPECIFICATION...............................................................................................36
Chapter 8 NETWORK SURVEILLANCE............................................................................38
8.1 AP Software Installation and Setup.......................................................................38
8.2 AP Software Operation .........................................................................................40
The author assumes no responsibility for any errors or omissions that may appear in this
document nor does the author make a commitment to update the information herein.
Page 5
1
Chapter 1 FEATURES
H.264 compression ideal for saving HDD space
Real time live display
Up to 120FPS @ 360x240 recording (NTSC)
Live display, record, backup, playback and network access at the same time
Control methods: front panel, USB mouse, IR remote controller, and client viewer
Intuitive GUI for easy configuration and menu driven operation
1 channel audio recording and playback
Supports 1 SATA HDDs
Pan / Tilt / Zoom camera control
Data backup: USB devices and network
Event triggered with email notification: motion detection, alarm, and video loss
Support AP on your PC end for remote operation
Multi-language OSD
Page 6
2
Chapter 2 PACKING DETAIL
1. DVR
2. Client Viewer Software CD 3. User Manual 4. Remote Controller
5. Power Cord 6. Power Adapter 7. Battery
8. SATA Cord 9. HDD Screws
CONTENTS
1. DVR
2. Client Viewer Software CD
3. User Manual
4. Remote Controller
5. Power Cord
6. Power Adapter
7. Battery
8. SATA Cord
9. HDD Screws
Page 7
3
Chapter 3 LOCATION AND CONTROL
3.1 Front Panel Controls
Item Description
1
ESC/ BACKUP
Exit various functions and menu screen
Video data storage backup
2
SEARCH
Enter search menu screen, use Up/ Down button to navigate
Press ENTER to access selected item
3
PIP
Turn on picture-in-picture format, use Up/ Down button to navigate
Press ENTER to access selected item
4
ZOOM
Enable/ Disable double screen size display.
Press ENTER to switch channels.
5
AUTO
Enable auto mode, to skip channels
Press MENU to disable auto mode
6 LED DISPLAY - REC DVR Recording.
7 LED DISPLAY- POWER DVR Power is on.
8 USB 2.0 The USB 2.0 port can be used to connect to numerous USB 2.0 backup devices.
9 REC Start/ Stop recording.
10 PLAY Start playing back.
11
MENU/ PAUSE
( MENU/ )
Enter menu mode, use Up/ Down button to navigate menu screen.
Press to pause playback
12 IR SENSOR Input sensor for the remote control.
13
RIGHT DIRECTIONAL
BUTTON/ FAST ( / )
Right Directional Button.
Fast Forward Playback, Speed: 2x, 4x, 8x, 16x, 32x, 64x.
14
UP DIRECTIONAL
BUTTON/ SLOW ( / )
Up Directional Button.
Slow Forward Playback, Speed: 1/2x, 1/4x, 1/8x, 1/16x.
15
DOWN DIRECTIONAL
BUTTON/ STOP ( / )
Down Directional Button.
Stop Playback.
16
LEFT DIRECTIONAL
BUTTON/ REWIND ( / )
Left Directional Button.
Fast Forward Playback, Speed: 2x, 4x, 8x, 16x, 32x, 64x.
17 ENTER/ MODE ( ) Switch to full screen and quad screen.
Page 8
4
3.2 Real Panel Connectors
Item Description
1 MAIN MONITOR BNC port for the main monitor.
2 VIDEO IN BNC input ports for cameras, 4 in total.
3 AUDIO IN RCA input port for an audio signal
4
NTSC／PAL SWITCH
Switch between NTSC and PAL format.
5 LAN Network port.
6 VGA Output port for the VGA monitor (option).
7 EXTERNAL I/O
EXTERNAL I/O port (see below for pin definition)
8 AUDIO OUT RCA output port for an audio signal
9 SPOT MONITOR BNC port to display full screen image of all installed cameras in sequence.
10 DC 12V Socket for a DC 12V input.
Page 9
5
3.3 Remote Controller
Remote Controller – Button Definition
○
1
LOCK
Enable Keypad Function.
○
2
STATUS
Display Status.
○
3
REC
Start/ Stop Recording.
○
4
FREEZE
Turn On/ Off Live Display FREZZE Function. Turn On/ Off Screen FREEZE Function.
○
5
PIP
Enable/ Disable On Picture-In-Picture Format.
Use Directional button to navigate the menu item, and press Enter button to
enter the menu item.
○
6
OSD
Turn On/ Off the Screen Display.
Page 10
6
○
7
ZOOM
Enable/ Disable double screen size display.
Use Directional button to navigate the screen display, and press Enter button to
switch channels.
○
8
MENU/
Enable/ Disable Menu.
Pause Playback.
○
9 ////
Up Directional Button.
Slow Forward Playback, Speed: 1/2x, 1/4x, 1/8x, 1/16x.
○
10
ESC
Exit Button.
○
11 /
/ /
/
Left Directional Button.
Fast Rewind Playback, Speed: 2x, 4x, 8x, 16x, 32x, 64x.
○
12
ENTER/ MODE
Switch to Single Screen/ Quad Screen Display.
○
13 /
/ /
/
Right Directional Button.
Fast Forward Playback, Speed: 2x, 4x, 8x, 16x, 32x, 64x.
○
14
PLAY
Start Playing Back.
○
15 /
/ /
/
Down Directional Button.
Stop Playback.
○
16
SEARCH
Enter the SEARCH menu.
Use Up/ Down Directional Button to navigate the menu item, press Enter button
to enter menu item.
○
17
IRIS +
PTZ Iris-Open.
○
18
ZOOM +
PTZ Zoom-In.
○
19
FOCUS +
PTZ Focus-In.
○
20
AUTO
In AUTO mode, all available channels will be cycled through in full screen.
○
21
IRIS -
PTZ Iris-Close.
○
22
ZOOM -
PTZ Zoom-Out.
○
23
FOCUS -
PTZ Focus-Out.
○
24
COPY
Enter the COPY menu.
○
25
CAMERA BUTTONS
Camera Select / Numeric Button.
Press [+10] button to select channels.
○
26
MUTE
Switch to 1-CH Audio Out/ Turn Off Live Audio.
○
27
Switch to Quad Display.
○
28
Switch to 9-Channel Display. 4-CH doesn’t support this function.
○
29
Switch to 13-Channel Display. 4-CH doesn’t support this function.
○
30
Switch to 16-Channel Display. 4-CH doesn’t support this function.
○
31
PRESET
Lens PreSet Point Setup
Press PRESET button+ 2 numeric numbers to save current lens location
PLAY+ Numeric Number to move lens to preset point.
○
32
TOUR
Activate PTZ Preset Tour.
○
33
PTZ
Start/ Stop PTZ Control.
Page 11
7
3.4 Mouse Control
Live Mode
Single Channel Display Move the cursor to the desired channel and double left click.
Change from Single-Channel
to Multi-ChannelDisplay
Double left click
Mouse – Menu Mode
Enter Menu setup Right click
Select/ Enter Left click
Return to Previous Page Right click
Mouse – Graphic Icons
Resting the cursor on this icon will bring up the four (Main Menu/ Search/
Backup/ PTZ) menu icons.
MAIN MENU
SEARCH SETUP.
BACKUP.
PTZ CONTROL.
Turn On/Off recording.
PLAYBACK
Resting the cursor on this icon will bring up five (PAUSE/ PIP/ ZOOM/
AUTO SEQ/ LOCK) display icons.
PAUSE, to pause LIVE image
PIP, picture in picture
ZOOM, double the screen size
AUTO-sequence
LOCK, activate the key lock.
Page 12
8
Full screen display, multiple clicking to switch channels
Quad display.
Mouse – GUI Hints and Tips
Recording is on
Live Audio is on
Live Audio is off
Motion detected on the channel
Sensor triggered on the channel
Video loss detected on the channel
USB device detected
DVR has been connected onto the Internet.
Timer recording is on
Red：Timer is set and recording has been started
White：Timer is set but recording has not yet been started
AUTO-SEQ is on
2X zoom in is on
2X FREZZE is on, screen is frozen
LOCK is on
PTZ control is on
Recording is on
Page 13
9
3.5 Playback Mode
Under the LIVE mode, the graphical icon [ ] will show up on the upper center of the
screen and the operation panel (see below picture) will show up at right lower corner of
the screen. You can drag the panel by mouse to place it on any location of your screen.
Playback – Quick Function Icon
Press「 / 」button to Fast Rewind
Speed : 2x, 4x, 8x, 16x, 32x, 64x
Press「 / 」button to Fast Forward
Speed : 2x, 4x, 8x, 16x, 32x, 64x
Press「PLAY
PLAYPLAY
PLAY」/ 「 」button to Play/ Pause Playback
「 / SLOW
/ SLOW / SLOW
/ SLOW」
slow playback
Speed : 1/2x, 1/4x, 1/8x, 1/16x
「 / 」
stop playback
Speed : 1/2x, 1/4x, 1/8x, 1/16x
Playback channel by channel with snap shot display
Full screen display
Quad display
Page 14
10
3.6 PTZ Mode
Under LIVE mode, PTZ icon [ ] will appear on the upper left of the screen or be
re-located on any place of your screen by dragging the mouse.
PTZ – Remote Controller Control
/ SLOW
Move PTZ up.
/
Move PTZ down.
/
Move PTZ to the left.
/
Move PTZ to the right.
ZOOM +
PTZ zoom-in.
ZOOM -
PTZ zoom-out.
FOCUS +
PTZ focus-in.
FOCUS -
PTZ focus-out.
IRIS +
PTZ iris-open.
IRIS -
PTZ iris-close.
TOUR
Activate PTZ pre-set tour.
PRESET + NUMBER
To save a preset location
Press PRESET and a number key. DVR will save the current location.
PLAY + NUMBER
To go to a preset location
Press PLAY and a number key. DVR will move to the preset location.
ZOOM
Set current PTZ location as the start of the line-scan.
PIP
Set current PTZ location as the start of the line-scan.
FREEZE
Activate line-scan.
Page 15
11
PTZ – Quick Function Icon
Exit PTZ Mode and back to the LIVE mode
Preset number N. (1~64)
Go to preset number N.
Set current PTZ location at preset number N.
[TOUR] icon, click to activate preset tour
Same as [PIP]. Set current PTZ location as the starting point of the
line-scan.
Same as [FREEZE]. Activate line-scan.
Same as [ZOOM]. Set current PTZ location as the ending point of the
line-scan.
To move PTZ in 360°
PTZ zoom in or PTZ zoom out
PTZ focus in or PTZ focus out.
PTZ IRIS open or PTZ IRIS close.
Below functions needs support from specific PTZ. Please check the user manual of your PTZ
manufacturer for detail.
AUX 1. [AUTO] ＋「1」
AUX 2. [AUTO] ＋「2」
AUX 3. [AUTO] ＋「3」
AUX 4. [AUTO] ＋「4」
AUX 5. [AUTO] ＋「5」
AUX 6. [AUTO] ＋「6」
AUX 7. [AUTO] ＋「7」
AUX 8. [AUTO] ＋「1」
[Backup] icon, click to customized function.
Page 16
12
Chapter 4 INSTALLATION
4.1 System Configuration
Page 17
13
4.2 Hard Disk Installation
Step 1 : Remove the 3 screws from DVR as cycled below (PIC 1).
(PIC 1)
Step 2 : Remove the front cover from DVR as indicated by the arrow (PIC 2).
(PIC 2)
Step 3 : Place the HDD on the HDD plate and connect the power and the SATA cables (PIC 3).
(PIC 3)
Page 18
14
Step 4 : Screw the bottom of the DVR as indicated as cycled (PIC 4).
(PIC 4)
Page 19
15
Chapter 5 BASIC OPERATION and MENU SETUP
5.1 Main Menu Setup
To enter the main menu and setup the DVR, please log-in account and enter user
password. The default password of the administrator is “123456”. Please refer to
“Account Setup” for related setup of other log-in users.
Main Menu – Mouse Control
Switch between capital and small letters.
/
Switch between numbers and letters.
Press to cancel the setup, and re-choose the login account.
Delete the last character.
Enter to identify the password. It will enter the setup menu if the password
is verified.
Main Menu – Remote Control ler and Front Pannel Control
Switch to different options under one item
Switch to different items
MENU
MENUMENU
MENU Save setup and back to LIVE mode
ESC
ESCESC
ESC Back to Upper level of the menu
ENT
ENTENT
ENTER
ERER
ER Enter the menu, or display virtual keyboard
Page 20
16
5.2 Record Setup
Item Description
HDD FULL
Select STOP to stop recording or OVERWRITE to reuse the HDD when
HDD is full.
[Stop]
：
Stop Recording
[Overwrite]
：
Start to overwrite beginning from the oldest data of HDD,
and continue to record.
Schedule - Record Normal
Enable/ Disable normal recording
Pre-Alarm Record
Enable/ Disable pre-event recording while motion or sensor is triggered
but not in the recording mode. This option decides if save the
pre-recording time 10 seconds data or not.
Audio Record
Enable/ Disable Audio recording.
Schedule - Motion
Enable/ Disable recording while Motion is detected
Schedule - Sensor
Enable/ Disable recording while Sensor is triggered
Video Preservation
Information stored within the HDD is preserved for only a specified length
of time.
Quality & Frame Rate
Setup…
Setup the quality and frame rate for each channel under normal
recording and event recording type.
Page 21
17
5.2.1 Quality & Frame Rate Setup
Item Description
Resolution
Choose record resolution, this value will be used by all channels.
Record Type
You can setup quality and FPS separately for record type.
No.
Check/ uncheck the box will enable/ disable recording of that channel.
Quality
Choose from Lowest/ Low/ Normal/ High/ Highest.
FPS
Choose recording frame rate.
5.3 Event Setup
Item Description
Alarm Duration (Seconds)
Set up alarm duration in seconds (can not be set to 0 seconds).
Drag the white bar or press ◀ ▶ to adjust value.
Motion Setup Enter to set up motion detection
Sensor Setup Enter to set up sensor detection
Page 22
18
5.3.1 Motion Setup
Item Description
Motion Detection Check the box to Enable/ Disable Motion Detection for all channels.
Motion Popup
Check the box to Enable/ Disable popup screen function for all channels.
When motion is detected in LIVE mode, the detected channel image will
popup in full screen display.
1 2 3 4
You can setup independently for each channel.
Selected Channel Turn Check the box to Enable/ Disable motion detection for each channel.
Object Size
Drag the white bar or press ◀ ▶ to set up Object Size from value 1 to 15
for each channel. The lower value you set the higher sensitivity it will be.
Sensitivity
Drag the white bar or press ◀ ▶ to set up Sensitivity from value 1 to 15 for
each channel. The lower value you set the higher sensitivity it will be
Motion Area Setup Enter to setup motion detection area
5.3.1.1 Motion Area Setup
There are 16x12 partitions in motion detection area. Under initializing status, motion
detection area is in the entire screen. Red colored area is detected; yet the
undetected area is transparent. It is purple while network is connected.
Item Description
LOCK / ZOOM Press LOCK / ZOOM to select the entire screen as detection area.
MUTE / PIP Press MUTE / PIP to deselect the entire screen as detection area.
STATUS Switch between “select” and “deselect” for cursor-dragging function
ENTER Press to activate selected area with assigned status
MENU Press to save the setup and leave
ESC Press to cancel the setup and leave
Page 23
19
5.3.2 Sensor Setup
Item Description
Sensor Detection Check the box to Enable/Disable sensor detection for all channels.
Sensor Popup Check the box to Enable/Disable popup screen function for all channels.
When Sensor is detected in LIVE mode, the detected channel image will
pop up in full screen display.
Sensor Polarity Click or press ▼ to select between HIGH/ LOW voltage for triggering
sensor detection or OFF to turn off polarity for each channel
Low Polarity：Sensor has not been triggered. When connected, sensor
will be turned on.
High Polarity：Sensor has been triggered. When connected, sensor
status will be turned off.
Off：Sensor is deactivated, and will not be turned on/off.
5.4 Schedule Setup
Apart from manual recording, you can also setup the recording time by weeks and
schedule recordings include: normal, motion detection, and sensor detection.
Item Description
Page
Click or press ▼ to select Page. Each page provides 10 schedules for
setup. 5 pages in total.
Holiday Setup Enter to setup holiday, maximum up to 50 days.
View Event Setup View Normal/ Motion / Sensor Setup.
Page 24
20
5.4.1 Schdule Record Setup
Click on the time icon on the left side. The setup menu will be displayed. You can have
detail setup by dates, time and event.
5.4.2 Holiday Setup
Since holidays are different between countries and regions, you can setup the holiday of
your location accordingly (Maximum Setup: 50).
5.5 Camera Setup
Page 25
21
Item Description
1 2 3 4
You can setup independently for each channel.
Mask
Check the box to Enable/ Disable mask function for LIVE mode
Brightness
Drag the white bar or press ◀ ▶ to adjust Brightness of your camera from
value 1 to 255. The default value is 128.
Contrast
Drag the white bar or press ◀ ▶ to adjust Contrast of your camera from
value 1 to 255. The default value is 128.
Saturation
Drag the white bar or press ◀ ▶ to adjust Saturation of your camera from
value 1 to 255. The default value is 128.
Hue
Drag the white bar or press ◀ ▶ to adjust Hue of your camera from value 1 to
255. The default value is 128. (This function is ineffective in PAL system).
Name
Set up name of each channel.
Volume
Select to adjust audio volume for CH1 to CH 4 under LIVE mode and
recording mode.
5.6 Account Setup
The Account Setup menu is used to provide role-based permission independently for
each user (maximum of 4 users) to access the DVR over network. The default admin
account is [admin] and password is “123456”.
Item Description
After one minute without any action, the DVR will switch to LIVE mode
automatically. Auto lock can function differently according to the setting below.
Function
Setting
Auto Logout Key Lock
Key lock ○ ○
Key unlock ○ ×
Auto Lock
Disable × ×
No.
Check to activate the user’s account.
Password
Enter to set up password for each user. Password must be at least 8
characters, including letters and numbers. Resetting Adiminstartor
password must also be at least 8 digits.
Permissions
Enter to setup Permissions for each user.
Change Admin Password
Enter to change administrator’s password.
NOTE!
Network LIVE videos are unable to be switched off when applying Mask function. To avoid network LIVE
videos, please use User permission mask playback features (Administrator has no such permissions).
Page 26
22
5.6.1 Permission Setup
The Account Setup is set to provide individual user (maximum of 4 users) role-based
permissions, including access to Setup menu, Network operation, PTZ function,
Playback, Utility, Backup and Mask on specific channels while playing back.
5.7 Network Setup
Item Description
Connect type
Setup mode for network connection: DHCP、LAN、ADSL.
HTTP Setup
Enter to set up HTTP for remote access into DVR.
DDNS Setup
Enter to Enable/ Disable DDNS function and set up.
Mail Setup
Enter to Enable/ Disable Email notification and setup.
NOTE!
1: When logged out automatically, you will have to operate in limited authority such as
operations like: Freeze the screen, Picture in picture, Zoom in/ out, switch between
channels…etc. If you need to enter the Setup menu, Search menu, backup menu,
Record…etc, user’s account and password are required.
2: When the key lock is activated automatically, remote control and mouse may not function unless
entering verified password, remote-site will not be able to operate all the features (including
toolbar).
3: [○] : Enable the function, [×] : Disable the function.
Page 27
23
5.7.1 Networking Setup
The DVR supports DHCP, LAN and ADSL access for network connection.
5.7.1.1 DHCP
If the DHCP option is used for DVR network connection, an IP address is assigned by
the DHCP server automatically.
5.7.1.2 LAN
Select LAN for network connection, the following information is required.
Item Description
IP Address
Enter IP address provided by ISP
Subnet Mask
Enter IP address of Subnet Mask provided by ISP
Gateway
Enter IP address of Gate way provided by ISP
DNS
Enter DNS address provided by ISP. (Note: The correct DNS address
must be entered for DDNS function).
5.7.1.3 ADSL
Select ADSL for network connection, the following information is required.
Item Description
User Name
Enter user name provided by ISP
Password
Enter password provided by ISP
Page 28
24
5.7.2 HTTP Setup
Item Description
Enable HTTP Server
Check to enable HTTP server. Users can remotely access into the DVR
over the network if the HTTP function is activated.
Port
Enter a valid port value from 1 up to 65000. The default value is 80.
5.7.3 DDNS Setup
Item Description
Enable DDNS
Check/ Uncheck to Enable/ Disable DDNS function.
DDNS Server
Enter the registered SMTP Server:
DYNDNS.ORG, NO-IP.ORG, CUSTOM.COM
SMTP Server
Enter the registered SMTP Server.
User Name
Enter user name.
Password
Enter password.
Page 29
25
5.7.4 Mail Setup
E-mail can be used as a form of notification when an event occurs (VLOSS, MOTION,
and SENSOR).
Item Description
Enable E-mail Notification
Check the box to enable/disable E-mail Notification function.
SMTP Server
Enter to set up SMTP Server name.
User Name
Enter to set up User Name.
Password
Enter to set up Password.
Sender E-mail
Enter to set up e-mail address of receivers.
E-mail address
Enter to set up e-mail addresses for up to 10 receivers individually.
Trigger Event
Enter to select events to send out E-mail notifications when below
circumstances happen: Motion, Sensor and Vloss (Video Loss).
5.8 PTZ & RS-485 Setup
The DVR allows users to control PTZ functions of your camera. To enable PTZ function,
the 485 cable should be connected to the RS-485 port of DVR.
Page 30
26
Item Description
Enable PTZ
Click the box to Enable/Disable PTZ function for each channel.
Protocol Set up the protocol of PTZ cam. The supported protocol are PELCO-P,
PELCO-D, and KND
PTZ ID
Click or press ◀ ▶ to set up PTZ ID. The valid ID value is from 1 to 64.
Baud Rate
Select Baud Rate for PTZ from 2400、4800、9600
5.9 System Setup
Item Description
DVR Name
The name of DVR will be shown when users login from remote access.
DVR Location
The location of DVR will be shown when users login from remote access
Language
Click or press ▼ to select OSD language.
Auto-Seq Interval
( Seconds)
Click or press ◀ ▶ to set up duration time in seconds for the interval
between channels under Auto-Seq mode.
Remote ID
Preserved Function.
Display Setup
Enter to set up Display
Date/Time Setup
Enter to set up Date/Time
Buzzer & Relay Setup
Enter to set up Buzzer & Relay
Spot Setup
Enter to set up Spot
Page 31
27
5.9.1 Display Setup
Item Description
OSD
Turn On / Off OSD display
DVR Status
Turn On / Off DVR illustration and record status display
Date/Time
Turn On / Off date and time display
Channel Name
Turn On / Off channel name display
Border Set
Set up the color of border in LIVE , PLAYBACK mode.（black, dark grey,
light grey, and white）
5.9.2 Date/ Time Setup
Item Description
Hour Format
12HOURS/ 24HOURS
Date Format
MM-DD-YY/DD-MM-YY/YY-MM-DD
Date/Time Position
Choose the position of Time and Date display
Change Date & Time
Setup time and date of DVR
Time Zone Setup
Set up GMT and Daylight Saving Time.
Internet Time Setup
Setup automatic synchronization with internet server
Page 32
28
5.9.2.1 Change Date & Time
Users are allowed to setup date and time of the DVR.
5.9.2.2 Time Zone Setup
In time zone setup, users can change the time zone and activate Daylight Saving Time
function according to your DVR location.
Item Description
Select Time Zone
Enter to modify GMT from GMT- 13 to GMT+ 13
Daylight Saving Time
Turn On/ Off Daylight Saving Time
5.9.2.3 Internet Time Setup
Synchronize your DVR time with internet time server.
Item Description
Automatic Synchronization
Check to enable DVR automatic synchronization function. Select this
option to enable the function, DVR will automatically synchronize the
time upon rebooting or by every 24 hours after booting.
Update Now
Date and Time show on DVR will immediately correspond with those in
internet server.
Page 33
29
5.9.3 Buzzer & Relay Setup
Item Description
KEY TONE
Enable/ Disable keystrokes.
Relay Switch Connection
Set relay signal to be Normal Close (N.C.) or Normal Open (N.O.).
Buzzer Duration
Set up the duration from 1~999 seconds.
ALARM BUZZER
Enable/ Disable buzzer operation when the alarm is triggered for sensor,
motion and vloss (Video Loss).
ALARM RELAY
Enable/ Disable the signal to be sent to the RELAY OUT blocks when the
alarm is triggered for sensor, motion and vloss.
5.9.4 Spot Setup
The DVR has two modes of video output; one is the main video output, the other is spot
video output. SPOT setup is for controlling orders of channels that the system cycles
through in SPOT mode. User can monitor every channel in the SPOT mode.
Item Description
SPOT MODE
Channels display in spot for three different modes:
MANUAL: Select channels to display manually, select channels will
be transfered to the SPOT monitor.
SEQUENCE: Auto-sequence for all channels in order.
EVENT: Display channels with event occurred.
Interval (Seconds)
The duration interval time between channels is in seconds under SPOT
mode (can not be set to 0 seconds).
Skip Video Loss Channel
Whether to skip channels without video signal.
Page 34
30
5.10 Utility Setup
Item Description
HDD Initialization Select to enter hard disk initialization menu. Please stop recording
before entering this menu. Enter the menu, system will show all the
data (model/ volume) of HDD that is installed in the DVR. Check the HDD
you’d like to initialize, then press “Start”. HDD initialization is successful
when the status shows “Succeed”.
USB Initialization
Clean up all data on USB. Enter USB initialization and press “YES” to
clean up all data on your USB. The initialization is done when it shows
“Succeed”.
System Recovery
Restore system default values.
Reset System Events
Reset all the recording events in the DVR.
Copy Setup to USB
Copy configuration to a USB device. There will be a file named
“sdvr.config” on your USB.
Download Setup from USB
Download configuration from a USB device into DVR.
Upgrade
Upgrade DVR through USB.
Please stop recording and backup setup configuration before upgrading.
System will reboot automatically when the upgrade is completed.
NOTE！！！！ DO NOT TURN OFF POWER OR UNPLUG USB DEVICE DURING THE UPGRADE as it
may cause incomplete firmware upgrade and damage to the DVR.
Page 35
31
5.11 Diagnostic
Item Description
Version
The current firmware version of DVR
IP Address
The connected IP address of DVR. If disconnected from network, the
screen will display” NETWORK DISCONNECT”.
MAC Address
MAC Address of DVR
HDD Volume
The capacity of HDD
HDD Used Rate
Percentage of space used on HDD.
HDD Status
Shows HDD status.
USING means the HDD is now used for recording.
GOOD/ BAD means the HDD has a known/ unknown format for the
DVR. (Note: Please initialize your newly-installed HDD before using it,
otherwise it can be recognized as BAD by the DVR).
Format Time
The latest format time of HDD
Page 36
32
Chapter 6 SEARCH & BACKUP
6.1 Search Setup
Item Description
Event Search
Press to enter event search menu.
Time Search
Press to enter time search menu.
Select Playback Channels
1~4
Check the desired channels to playback; uncheck channels to
show LIVE video images.
6.2.1 Event Search
The DVR automatically records events with type, time and channel information included.
If there is recording data for an event, a yellow signal
icon will be shown on the left
side of time information. Rest your cursor under the line and press “enter”, or left click
your mouse to playback the recording data.
Page 37
33
Item Description
Criteria
Setup conditions of the event search function
Page
Convert pages of events
Date/Time
Date/ time when the event occurred.
Event type, defined as following:
VLOSS
: Video Loss
MOTION
: Motion Detected
SENSOR
: Sensor Detected
REMOTE IN
: User log-in over the network
REMOTE OUT
: User log-out over the network
POWER ON
: System Rebooting
KEY LOCK
: System key is locked
KEY UNLOCK
: System key is unlocked
Event Type
HDD FULL
: HDD is FULL
Channel
The channel where the event occurred.
6.2.1.1 Criteria Setup for Event Search
The amount of events can be numerous. Therefore, you can facilitate event sorting by
setting up “criteria”. Setup “start time” and “end time” for each event search, then the
search result will be limited to this specific period of time. Only events and channels that
are checked will be sorted in event search as well.
Page 38
34
6.2.2 Time Search
TIME SEARCH, you can search for a specific time of the recording data to playback.
Dates with recording are shown by data marked with a red square [
□ ]. System will
start playing back according to the date that you’ve selected. Calendar will be shown
by using mouse to click on “year” and “month”.
Click “date” to display recording time of that specific date with time bar. You can
change time (hour/ minute/ second) or click on a specific time of time bar by mouse
then press “YES”. DVR will playback the selected recording data.
Page 39
35
6.2 Backup Setup
User can back-up any segment of recorded data in a specified time frame. To do so,
connect a USB to the DVR. The format of backup file is IRF file and can be played by
“DVRemoteDesktop.exe” or “iCMS”.
Item Description
From
Backup file starting time
To
Backup file ending time
Device
Select USB as the backup device
Free Space
The available space in your backup device
Refresh
Recalculate the available space of backup device
Calculate
Calculate the size of backup file
Start
Start backup operation. Be sure to calculate the size of backup file BEFORE
operating backup.
NOTE！！！！ Do not unplug the USB device or turn off the DVR during the backup process to avoid
unrecoverable error. When backup is completed, you need to re-plug in order to insure
proper function.
Page 40
36
Chapter 7 SPECIFICATION
VIDEO SYSTEM NTSC/ PAL Selectable
INPUT 4CH BNC
LOOP N/A
VIDEO OUTPUT 1CH, BNC
SPOT OUTPUT 1CH, BNC
VIDEO
VGA OUTPUT Optional
INPUT 1CH, RCA
AUDIO
OUTPUT 1CH, RCA
SENSOR
4 Inputs/ 1 Outputs
TERMINAL
RS-485 INTERFACE Pan/ Tilt/ Zoom Camera
MOUSE USB Mouse
CONTROL
IR CONTROLLER
YES
DEVICE Supports SATA Hard Disk x1
STORAGE
DVD WRITER N/A
DIVISION 1,4
ZOOM 2X
DISPLAY
OSD Graphic OSD
COMPRESSION H.264
RESOLUTION
720x480, 720x240, 360x240 (NTSC)
720x576, 720x288, 360x288 (PAL)
NTSC 30, 60, 120FPS FRAME
RATE
PAL 25, 50, 100FPS
QUALITY Highest/ High/ Normal/ Low/ Lowest
RECORD MODE Manual, Schedule, Event (Motion Detection, Sensor, Video Loss)
User selectable motion detection area for each camera individually
MOTION DETECTION
Sensitivity: 5 levels
PRE-ALARM 16 MB
POST-ALARM 16 MB
RECORDING
WATERMARK N/A
SEARCH MODE Time, Event
SPEED Normal, REW&FF[2x/4x/8x/16x/32x/64x], Picture to Picture, Pause
INTERNAL HDD
PLAYBACK
EXTERNAL N/A
Page 41
37
COMPRESSION H.264
INTERFACE Internal Exploerer Browser
NETWORK
SERVICE TCP/ IP, SMTP, HTTP, DHCP, DDNS, PPPoE
INTERNAL N/A
EXTERNAL USB 2.0 (1 Port at Front Panel) : USB Flash Driver
NETWORK YES
BACKUP
BACKUP FILE H.264 Compression
MONITORING Software Watchdog
RECOVERY Auto-Reboot By Watchdog
FIREWARE
UPGRADE
USB 2.0 Port (1 Port at Front Panel)
MULTI-LANGUAGE
English/ Traditional Chinese/ Italian/ Japanese/ Portuguese/ Spanish/ German/ French/ Russian
/
Simplified Chinese/ Polish
DIMENSION 188mm (W) x 54mm (H) x209mm (D)
POWER SOURCE
DC 12V
Page 42
38
Chapter 8 NETWORK SURVEILLANCE
AP software:「DVR Remote Desktop」can allow you to remotely access and control the
DVR from the PC
.
8.1 AP Software Installation and Setup
Step 1：Enter the IP address of the DVR in the IE browser.
Step 2: A window will pop-up. Please enter the user name and password. Default user
name is admin and password is 123456. Other related setup about user
account and password, please refer to “5.6 Account Setup“.
Step 3: Click on the link to start downloading the AP software.
Page 43
39
Step 4: Run or Save our AP software.
Step 5: If you choose to run the software, “Start” window will be shown. Please enter the
information for the login DVR: IP, Port, Username and Password, or choose
“Play Recorded File” to open backup files on your PC.
Step 6: You’ve logged into the DVR
Page 44
40
8.2 AP Software Operation
Open the file “DVRemoteDesktop.exe”; enter the information of the DVR “IP address”,
“Port” “Username” and “Password” and click “OK”. You should be able to login the DVR
successfully and start to use the software. The default username and password is
[admin/ 123456].
After successful login, the operation and interface will be the same as the local DVR.
Tool Bar Description
File - Record to Local
Record data to your PC, including LIVE and Playback.
File - Play Recorded Files Play recorded files “.irf”
File - Exit
／ Alt + F4
Close the AP software.
Edit - Channel Name
／ F2
Edit channel name of your DVR including font, size italic, and boldface of
characters. .
Edit - Reset Channel Name Reset channel name back to default.
View - Hide Caption & Menu
／ F9
Hide the Caption and
View - Disable resizing
／ F10
Disable resizing the window.
View - Full screen
／ F11
Switch it to full screen
Help – About Show information about software and information
Loading...