MultiDyne GP-3G-20-ST3-A, GP-3G-20-ST3-B, GP-10G-40-ST3-A, GP-12G-10-ST3-A, GP-10G-40-ST3-B Configuration And Installation Manual

...

Download

Page 1

CONFIGURATION AND INSTALLATION MANUAL

GENPLEX 3G, 10G & 12G REPEATER

REGEN REPEATER

MultiDyne Product for Single and Double Fiber Solutions

MultiDyne

Harnessing The Power of Light

10 NEWTON PLACE

HAUPPAUGE, NY 11788 USA

(877) 685-8439 / (516) 671-7278 / FAX (516) 671-3362

sales@multidyne.com

www.multidyne.com

Page 2

MULTIDYNE, the Multidyne logo,

are registered trademarks of MULTIDYNE Electronics, Inc.

Printed in the United States of America.

Contents of this publication may not be reproduced in any form without the written permission of

MULTIDYNE Electronics, Inc.

This product was designed and manufactured in the

UNITED STATES of AMERICA

Page 3

Important Safety Information

• Do not use this apparatus near water.

• Clean only with lint free dry cloth.

• Do not block any ventilation openings.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

• Do not defeat the safety purposes of the groundingtype plug. A ground type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not ﬁt in to your outlet, consult an electrician for replacement of the obsolete outlet.

• Install in accordance with the MultiDyne® installation instructions.

• Install all peripheral equipment (cameras, routers, etc.) in accordance with the manufacturer’s instructions and safety requirements.

• Protect the power cord from being walked on or pinching particularly at plugs, convenience receptacles, and point

<2000m

where they exit from the apparatus.

• Only use attachments/accessories speciﬁed by MultiDyne®.

• Use only with the cart, rack, stand, tripod, bracket, or table speciﬁed by MultiDyne®, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Follow all local Electrical Codes for Grounding, Lightning Arrestment and Surge Protection. Unplug this apparatus during lightning storms or when unused for long periods of time.

• All Electrical Work to the facility must be performed by a qualiﬁed Licensed Electrician. All local Electrical Codes must be followed and, if necessary, must be inspected by a Local or State Inspector.

• All servicing of MultiDyne equipment must be perform at the factory by a MultiDyne trained service technician or engineer.

• Throughout this manual, a number of Warnings and Cautions and Notes may be presented to alert the user to important safety or operating information.

• Always adhere to local building, safety and ﬁre prevention codes during the installation and operation of this product.

• Use only power cords that were shipped with speciﬁed for this product and certiﬁed for the country of use.

• Connect the unit only to a power source with the speciﬁed voltage rating.

• Unless otherwise stated in the Installation Instructions, and in adherence to local Electrical Codes MultiDyne® Equipment should only be plugged into a standard 15 amp dedicated circuit.

Warning –indicate danger that requires proper procedures or practices to prevent injury or death to personnel.

Cautions indicate proper procedures or practices to prevent damage to equipment or property.

Warning –The safe operation of this product requires that a protective earth connection be provided. A grounding conductor in the equipment’s mains supply cord provides this protective earth. To reduce the risk of electrical shock to the operator and service personnel, this ground conductor must be connected to an earthed ground. The mains plug shall remain readily operable.

Warning –The apparatus shall not be exposed to dripping or splashing and that no objects ﬁlled with liquids, such as vases, shall be placed on the apparatus.

Warning - This symbol on the equipment indicates for use at altitudes not exceeding 2000 m.

Warning - Contact your local authority for further details on the correct disposal of this waste, in accordance with your national legislation.

Laser Safety Information

This unit is classiﬁed as a CLASS 1 LASER PRODUCT according to EN60825-1 (EU) and FDA 21CFR 1040.10 (USA). Class 1 laser products are considered safe and do not result in biological hazard if used according to these instructions.

Warning – Use of controls, adjustments or performance of procedures other than those speciﬁed herein may result in hazardous radiation exposure.

Warning – Never look directly into the end of the optical ﬁber while either end of the system is operating.

Warning – Never clean an optical ﬁber connector on equipment or cable that is carrying light.

Warning – Always use dust caps on ﬁber optic connectors when cables are not connected. This will protect the connector from damage and accidental exposure of a human eye to an operating laser.

Page 4

TABLE OF CONTENTS

INTRODUCTION .................................................................................................................... 1

Overview .............................................................................................................................1

Repeater Models ..................................................................................................................1

Unpacking ...........................................................................................................................1

FUCTIONAL DESCRIPTION ................................................................................................... 2

GenPlex Repeater ............................................................................................................... 2

Regen Repeater .................................................................................................................. 2

INSTALLATION ..................................................................................................................... 3

Tools and Equipment Needed ............................................................................................. 3

Network Conﬁguration ....................................................................................................... 3

Mounting ............................................................................................................................ 4

Optical Budget .................................................................................................................... 4

Connections ........................................................................................................................ 4

TECHNICAL SPECIFICATIONS ............................................................................................... 5

GenPlex Mechanical, Environmental ................................................................................... 5

Page 5

GenPlex 12G Repeater Conﬁguration and Installation 1

IINTRODUCTION

Overview

The purpose of this manual is to provide conﬁguration information and installation instructions for GenPlex and Regen Repeaters. The repeaters are sold in pairs with an A model connected to the Hybrid Universal Transceiver (HUT) on the Camera side and a B model connected to a HUT for the Camera Control Unit (CCU) side. The GenPlex are devices used with the HUT to increase the range of the ﬁber connection. The GenPlex models that can be ordered for 3G, 10G and 12G.

Repeater Models

Qty Repeater Model Number Use in Network

1 GenPlex GP-3G-20-ST3-A Camera/HUT Side

1 GenPlex GP-3G-20-ST3-B CCU/HUT Side

1 GenPlex GP-10G-40-ST3-A Camera/HUT Side

1 GenPlex GP-10G-40-ST3-B CCU/HUT Side

1 GenPlex GP-12G-10-ST3-A * Camera/HUT Side

1 GenPlex GP-12G-10-ST3-B * CCU/HUT Side

1 Regen RGX-10G-40-ST4-A Camera/HUT Side

1 Regen RGX-10G-40-ST4-B CCU/HUT Side

*The 10G GenPlex can be special ordered for a distance of 80km with an optional Dispersion Compensation Module (DCM) unit.

Unpacking

GenPlex and Regen Repeaters are shipped as a pair within a single container or part of a larger container when ordered as part of a network. The container will contain:

• Two or more GenPlex or Regen Repeater models. Ի Verify the Quantity of the order against the shipping manifest. Ի Verify the Model Numbers based on the order placed and the table below.

• Two or more AC/DC Power Cords and Power Supplies for the repeater devices.

• Rack Mount (Metalwork) for installing in a 1U Rack (if ordered).

• Mounting Cover Plates to dress o unused Mounting Locations

• Bag of connectors and connecting hardware needed to complete installation.

Carefully remove the repeaters from packaging and place onto stable ﬂat surface. Packaging material should be recycled as appropriate to local area requirements.

Page 6

2 GenPlex 12G Repeater Conﬁguration and Installation

FUCTIONAL DESCRIPTION

GenPlex Repeater

GenPlex Repeater models available to enhance signal strength for distances up to 40km ± 2Km. These repeaters are designed for optimum performance in support of any network design and a multitude of camera models and manufacturers. Each GenPlex Repeater is conﬁgured internally with Small Factor Pluggable (SFP) module and Wavelength Division Multiplexing (WDM) devices of speciﬁc values to accommodate all single ﬁber and double ﬁber network solutions. A breakdown of the internal workings of the GenPlex repeater is shown in the table below.

Model Number External Connections Internal Conﬁguration Use

GP-10G-40-ST3-A

GP-10G-40-ST3-B

1 AMP OUT,

1 OPTICAL IN,

1 COMMON

1 AMP OUT,

1 OPTICAL IN,

1 COMMON

1 1310 SFP

1 1550 SFP

1 WDM

2 1310 SFP

1 WDM

Camera/HUT Side

Double Fiber Solution

CCU/HUT Side

Double Fiber Solution

Regen Repeater

There are four Regen Repeaters models available to enhance signal strength to 40km ± 2Km. These devices are designed for optimum performance in support of any network design and a multitude of camera models and manufacturers. Each Regen Repeater is conﬁgured with SFP modules of speciﬁc values to accommodate all single ﬁber and double ﬁber network solutions. A breakdown of the internal workings of each Regen repeater is shown in the table below.

Model

Number

RGX-10G-40-ST4-A

RGX-10G-40-ST4-B

External

Connections

2 A 2 B

Internal

Conﬁguration

2 1310 SFP

1 WDM

2 1310 SFP

1 WDM

Use

Camera/HUT Side

35km Distance

CCU/HUT Side

15km Distance

Page 7

GenPlex 12G Repeater Conﬁguration and Installation 3

INSTALLATION

Tools and Equipment Needed

The GenPlex and Regen Repeaters require standard hand tools to complete the installation. There is NO special equipment needed.

Network Conﬁguration

The diagram below shows the basic GenPlex and Regen network conﬁgurations commonly used for this product. This generic diagram illustrates a 40km ± 2Km network where the GenPlex and Regen repeaters are installed.

SMPTE

CONNECTION

CCU

HUT CP

AMP OUT

OPTICAL IN

GenPlex

COMMON

GenPlex HUT BS

AMP OUT

OPTICAL IN

HUT CP

SMPTE

ReGen

ReGen HUT BS

SMPTE

CONNECTION

SMPTE

CONNECTION

CCU

Page 8

4 GenPlex 12G Repeater Conﬁguration and Installation

Mounting

The repeaters are strategically placed in the middle of long distance runs to regenerate signal strength. The GenPlex or Regen boxes can be located within an existing equipment rack or any hard ﬂat surface where the ﬁber cable is being routed. The device requires no additional grounding or start up procedures. Existing Equipment Rack Mounting:

NOTE

The Rack Mount aluminum metalwork plate can be used for installing the Repeater(s) in a

1U Rack. The plate can accommodate six Repeater installations. For installations that do

not use six Repeaters, a blank dress plate is provided to cover the unused openings.

Ի Remove the four plate mounting screws and position the Repeater to the desired Rack Mount plate location. Install

the four screws that secure the Repeater to the plate.

Ի At the rack where the Repeater(s) is to be located make sure all wiring and loose equipment has been cleared away

to avoid any obstructions. Make sure the front and rear portions of the rack are clear so that the wiring can be routed

to the Repeater(s). Ի Slide the Rack Mount plate with Repeater(s) installed into the rack and secure with attaching hardware. Ի Using the Connections as a guide install the cables to the Repeater(s). Ի Position the dress cover plates over the unused openings and secure with attaching hardware.

Optical Budget

The optical power budget is the minimum amount of power needed to be applied to the GenPlex or Regen Repeaters from the ﬁber communications link. Optical power loss can be caused by various means including splices, coupling loss, connector loss and attenuation. It is important to the operational integrity of the GenPlex and Regen Repeaters that adequate optical power signal strength be available. The optical power budget is speciﬁed in decibel (dB) and optical power budget for the GenPles is 16dBm + 2dBm.

Connections

Connections for the GenPlex Repeaters are simple and provided in the table below.

HUT CAMERA SIDE

TO CCU

FROM CCU

Connections for the Regen Repeaters are simple and provided in the table below. Plug the AC/DC Power Cord Converter connector into the GenPlex unit at POWER 9-24VDC and secure. Plug the other end of the converter cord into wall or suitable Power Strip/Surge Suppressor.

HUT CAMERA SIDE

TO CCU

FROM CCU

GenPlex Model A

OPTICAL IN

AMP OUT

COMMON

ReGen Model A

GenPlex Model B

OPTICAL IN

AMP OUT

COMMON

ReGen Model B

HUT BASE SIDE

TO CAMERA

FROM CAMERA

HUT BASE SIDE

TO CAMERA

FROM CAMERA

Page 9

GenPlex 12G Repeater Conﬁguration and Installation 5

TECHNICAL SPECIFICATIONS

Mechanical, Environmental

Dimensions L 5.625 x W 2.625 x H 1.625 inches Operating Temperature 0 to 50 deg C Power Requirement 9 – 18 VDC Optical Connectors 3 ST