MultiDyne GP-3G-20-ST3-A, GP-3G-20-ST3-B, GP-10G-40-ST3-A, GP-12G-10-ST3-A, GP-10G-40-ST3-B Configuration And Installation Manual

CONFIGURATION AND INSTALLATION MANUAL

GENPLEX 3G, 10G & 12G REPEATER

REGEN REPEATER

MultiDyne Product for Single and Double Fiber Solutions

MultiDyne

Harnessing The Power of Light

10 NEWTON PLACE

HAUPPAUGE, NY 11788 USA

[phone] / [phone] / FAX [phone]

[e-mail]

www.multidyne.com

MULTIDYNE, the Multidyne logo,

are registered trademarks of MULTIDYNE Electronics, Inc.

Copyright 2019 MULTIDYNE Electronics, Inc., Hauppauge, New York.

Printed in the United States of America.

All Rights Reserved.

Contents of this publication may not be reproduced in any form without the written permission of

MULTIDYNE Electronics, Inc.

This product was designed and manufactured in the

UNITED STATES of AMERICA

Important Safety Information

• Do not use this apparatus near water.

• Clean only with lint free dry cloth.

• Do not block any ventilation openings.

• Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.

• Do not defeat the safety purposes of the grounding­type plug. A ground type plug has two blades and a third
grounding prong. The third prong is provided for your safety.
If the provided plug does not fit in to your outlet, consult an
electrician for replacement of the obsolete outlet.

• Install in accordance with the MultiDyne® installation
instructions.

• Install all peripheral equipment (cameras, routers, etc.) in
accordance with the manufacturer’s instructions and safety
requirements.

• Protect the power cord from being walked on or pinching
particularly at plugs, convenience receptacles, and point

<2000m

where they exit from the apparatus.

• Only use attachments/accessories specified by MultiDyne®.

• Use only with the cart, rack, stand, tripod, bracket, or table
specified by MultiDyne®, or sold with the apparatus. When
a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.

• Follow all local Electrical Codes for Grounding, Lightning Arrestment and Surge Protection. Unplug this apparatus during lightning
storms or when unused for long periods of time.

• All Electrical Work to the facility must be performed by a qualified Licensed Electrician. All local Electrical Codes must be followed
and, if necessary, must be inspected by a Local or State Inspector.

• All servicing of MultiDyne equipment must be perform at the factory by a MultiDyne trained service technician or engineer.

• Throughout this manual, a number of Warnings and Cautions and Notes may be presented to alert the user to important safety or
operating information.

• Always adhere to local building, safety and fire prevention codes during the installation and operation of this product.

• Use only power cords that were shipped with specified for this product and certified for the country of use.

• Connect the unit only to a power source with the specified voltage rating.

• Unless otherwise stated in the Installation Instructions, and in adherence to local Electrical Codes MultiDyne® Equipment should
only be plugged into a standard 15 amp dedicated circuit.

Warning –indicate danger that requires proper procedures or
practices to prevent injury or death to personnel.

Cautions indicate proper procedures or practices to prevent
damage to equipment or property.

Warning –The safe operation of this product requires that a protective
earth connection be provided. A grounding conductor in the equipment’s
mains supply cord provides this protective earth. To reduce the risk
of electrical shock to the operator and service personnel, this ground
conductor must be connected to an earthed ground. The mains plug shall
remain readily operable.

Warning –The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.

Warning - This symbol on the equipment indicates for use at
altitudes not exceeding 2000 m.

Warning - Contact your local authority for further details on the
correct disposal of this waste, in accordance with your national
legislation.

Laser Safety Information

This unit is classified as a CLASS 1 LASER PRODUCT according
to EN60825-1 (EU) and FDA 21CFR 1040.10 (USA). Class 1 laser
products are considered safe and do not result in biological
hazard if used according to these instructions.

Made in the USA November 2019© 2019 MultiDyne, Inc.

Warning – Use of controls, adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.

Warning – Never look directly into the end of the optical fiber
while either end of the system is operating.

Warning – Never clean an optical fiber connector on equipment or
cable that is carrying light.

Warning – Always use dust caps on fiber optic connectors when
cables are not connected. This will protect the connector from
damage and accidental exposure of a human eye to an operating
laser.