Mule Lighting , Inc. CEL Installation And Operation Instructions For
Renaissance Series
Mule Lighting , Inc. 46 Baker Street Providence, RI 02905 800 556-7690 P 401 941-2929 F www.mulelighting.com
Installation and Operation Instructions
Models CEL
FOR SURFACE MOUNT EDGE-LIT LED EXIT SIGN AC ONLY –
RENAISSANCE SERIES
SAVE THESE INSTRUCTIONS
IMPORTANT SAFEGUARDS:
When using electrical equipment, always adhere to basic safety precautions including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. Do not use outdoors.
2. Equipment should be mounted
securely in locations and at heights
where it will not be readily subjected
to tampering by unauthorized
personnel.
3. Do not mount near gas or electric
heaters.
4. Cap unused wires with enclosed
wire nuts or other approved method.
5. Do not use this equipment for
anything other than its intended use.
6. The use of accessory equipment not
recommended by the manufacturer
will void product listing and
warranty and may cause an unsafe
condition.
7. Disconnect AC power before
servicing and installation.
8. Any service on this equipment should
be performed by qualified personnel
only.
INSTALLATION INSTRUCTIONS
Choose mounting configuration (End,
Top, or Back Mount). Plug remaining
holes with the appropriate color plugs.
1. Secure canopy bracket to ceiling
or wall.
2. Open the housing cover.
3. Secure housing and canopy with
screws (see mounting configurations).
4. Feed the AC input leads (Red, Black,
White) through the housing and
canopy’s center hole. Connect AC
input leads to AC power supply
leads. Connect the Red lead to a
277VAC power supply or the Black
lead to a 120VAC power supply, and
the White lead to neutral.
5. Secure canopy into canopy bracket
with 1 1/2” long #8-32 screws.
6. Snap housing cover into place.
7. Apply
END MOUNT
1. Secure canopy to end plate of
2. Run connection wires through large
3. Make electrical connections and
chevron directional indicators
as required. Remove application
templates when finished.
fixture using Mounting Holes C and E
with (2)
hole between Mounting Holes C
and D.
mount canopy to junction box (or
spider plate if required) using the two
recessed mounting holes and (2) 11/2”
#8-32 screws (included).
3
/4” #10-24 screws (included).
TOP MOUNT
1. Secure canopy to top of fixture using
Mounting Hole A with #8-32 screw and
hex nut, and 1/2” center hole
(between Mounting Holes B and C)
with threaded nipple and hex nuts
(included).
2. Run connection wires through threaded nipple.
3. Make electrical connections and
mount canopy to junction box (or spider plate if required) using the two
recessed mounting holes and (2) 1
#8-32 screws (included).
END MOUNT
BACK MOUNT
BACK MOUNT
1. Mount canopy to junction box (or spider plate if required) using the two
recessed mounting holes and (2) 1
#8-32 screws (included).
2. Run connection wires through large
hole in center of canopy.
3. Secure fixture to canopy with (2) 3/4”
#10-24 screws (included) by going
directly into Mounting Holes A and C.
4. Make electrical connections.
1
/2”
TOP MOUNT
1
/2”
(Continued on back) pg 1 of 2
Renaissance Series
Mule Lighting , Inc. 46 Baker Street Providence, RI 02905 800 556-7690 P 401 941-2929 F www.mulelighting.com
Installation and Operation Instructions
Models CEL
FOR SURFACE MOUNT EDGE-LIT LED EXIT SIGN AC ONLY –
RENAISSANCE
IMPORTANT SAFEGUARDS:
When using electrical equipment, always adhere to basic safety precautions including the following:
WIRING DIAGRAM
SERIES
Loading...