Mueller® Resilient Wedge Gate Valves have features to make them easier to operate and to preserve the sealing capability and
interior coating integrity for many years of reliable service. In addition to popular end connection options, Mueller brand RW
valves can be ordered with Mueller’s exclusive Aqua-Grip™ System that incorporates an O-ring sealed compression connection
and integral pipe restraint in one “ready to use” easy and quick to install package.
Mueller 2" – 12" 2360 Series Resilient Wedge Gate Valve Features
❏ TRIPLE O-RING SEALS PLUS DIRT
SEAL – two above thrust collar and
one below, retain lubricant in this critical area. Top two are replaceable with
valve fully open and under pressure.
Fourth seal at top serves as dirt seal†.
❏ TWO ANTI-FRICTION WASHERS
WITH LUBRICATION – made of
polymer, one above and one below the
thrust collar, reduce operating torque
to open or close valve.
❏ STEM – forged manganese bronze bar
stock is upset, then machined to form
a thrust collar for superior strength in
this critical area.
❏ WEDGE – cast iron, fully encapsu-
lated in molded rubber - no exposed
iron.
❏ EXTENDED WEDGE GUIDES –
molded as part of wedge, ride inside
body channels to maintain wedge
alignment throughout its travel.
❏ GUIDE CAP BEARINGS – made
of polymer and snapped over rubber
covered wedge guides, provide bearing
surfaces that protect both wedge and
interior body coating from wear and
aid in easy operation – even the largest
valves installed horizontally. Rollers,
tracks or scrapers are not needed.
❏ SMOOTH, OVERSIZED FLOW WAY
– full, round, unobstructed flow way
accommodates full size cutters, provides
superior flow characteristics and reduces
pumping costs.**
❏ MUELLER® PRO-GARD™ FUSION
EPOXY COATING – 10 mils* thick
protects all inside and outside iron surfaces, and complies with AWWA C550
and certified to ANSI/NSF 61.
❏ 250 PSIG MAXIMUM WORKING
PRESSURE – Hydrostatically tested
at 500 psig. Surpasses ANSI/AWWA
Standard C509 by 25%. UL/FM: 200
psig MWP.***
❏ AMERICAN MADE QUALITY –
factory in Chattanooga, TN with ISO
9001:2000 certification, and UL 262,
FM 1120/1130. Certified to ANSI/NSF
61. Manufactured and tested in compliance with ANSI/AWWA Standard
C509. UL Listed and FM Approved.
❏ BI-DIRECTIONAL FLOW
❏ FLAT BOTTOM SURFACES – stands
upright for easier handling and storage.
❏ 10-YEAR LIMITED WARRANTY –
assured reliability (see separate Mueller
Warranty document for terms).
Rev. 2-06
Mueller 14" – 48" 2361 Series Resilient Wedge Gate Valve Features
In addition to all the features of the smaller 2360 series valves, large size Mueller 2361 series RW valves offer these features:
❏ STEM – Manganese bronze casting with
integral thrust collar.
❏ WEDGE – Ductile iron, fully encapsulated in
molded rubber.
❏ BODY AND BONNET – Ductile iron.
*Nominal
**16" valve requires 1/2" undersized cutter.
***250 psi UL/FM rating available as an option.
†Dirt seal on 4"-12" valves.
❏ COMPLIANCE – In addition to those above:
ANSI/AWWA Standard C515.
❏ MAXIMUM WORKING PRESSURE – 14"-48" AWWA
valves rated at 250 psig – tested at 500 psig.
UL/FM valves 200 psig MWP (14"-16" 250 psig
MWP).***
Double-Disc Style gate valves follow the RW valve pages.
10.44
Catalog
Part No.
DescriptionMaterialMaterial
standard
G-16Bonnet bolts & nutsSteelANSI B18.2 plated
G-24Test plugIron
G-26Nut for wrench nutSteelANSI B18.2 plated
G-32Stuffing box gasketFiber
G-38Wrench nutCast ironASTM A126 CL.B
G-41Stuffing box bolt & nutSteelANSI B18.2 plated
G-42StemBronzeASTM B138
G-45Hand wheelCast ironASTM A126 CL.B
G-48Stuffing box O-ringRubberASTM D2000
G-49Stem O -ringRubberASTM D2000
G-176Anti-friction washerCelcon
G-178Seat ringRubberASTM D2000
G-179Retaining screwStainless steel
G-181Bonnet gasketCompositionASTM D1170
G-183
Stem
Bronze
CDA Alloy 676
Pin
Bronze
G-23Stem packing Lubricated flax
G-1Cap nutBronzeASTM B62
G-2KeySteel
G-3HandwheelCast ironASTM A126 CL. B
G-4WasherBrass
G-5Bush nutBronzeASTM B62
G-7Gland nutBronzeASTM B21 Alloy 464
G-9GlandBronzeASTM B62
G-10Gland boltSteelANSI B18.2.1
G-11Yoke bolt and nutSteelANSI B18.2.1
G-184
Rev. 2-06
Resilient Seal Valve Parts
SUPER-SEAL™ RESILIENT SEAT NRS &
O.S.&Y. GATE VALVE PARTS - ALL ENDS
GATE VALVE
ORDERING INSTRUCTIONS
To order Gate Valves specify:
Quantity
If more than one size, specify quantity of each
Size
Nominal size of valve
Catalog number
Special catalog number suffix
See chart at bottom of page 10.40 if gearing, grease cases, bypass
valves or position indicators are required. The appropriate suffix
number is added to the base catalog number.
Direction of opening
Specify open left (counter-clockwise) or open right (clockwise).
Wrench nuts on valves that open to the right are painted red for identification purposes.
Method of operation
N.R.S. valves are available with either a 2" square wrench nut or a
handwheel. Handwheels are standard on flanged x flanged and thread
x thread valves; all other NRS* valves have a 2" square wrench nut
as standard. Outside screw and yoke type valves are available with
handwheel only. When ordering NRS valves, specify wrench nut or
handwheel.
* 30"-48" resilient wedge and double-disc gate valves must be ordered with
actuator.
10.43
Rev. 2-06
Special Requirements
Contact MUELLER Customer Service Center with special requirements such as special paints or coatings, low zinc bronze stems, stainless steel fasteners etc.
Gate Valve Repair Parts
To order repair parts specify size of valve, direction of opening, year
date on body, part number, catalog number of valve if known, and
type of ends if ordering body.
10.42
TypePart Number Sizes *Included
Flange endA-1992064"-12"Flat gasket,
bolts/nuts
MJ end - D.I.A-1990002", 3"-12"Ring gasket, DI
gland, bolts/nuts
MJ end - C.I.A-1991002", 3"-24"Ring gasket, CI
gland, bolts/nuts
MechanicalJointAccessories
Size valve *Standard
Mechanical
Joint Gland
Gland with
Bonding Set
Screws
Plain
Rubber
Gasket
2"155163181299194629
3"155024181301194531
4"155014181302194532
6"155016181303194533
8"155018181304194534
10"155020181305194535
12"155022181306194536
14"155273181307194684
16"155170181308194632
18"155352181314194729
20"155264181309194670
24"155263181310194671
30"155481-194779
36"155079-195169
Part No.
Part No.
Part No.
D-150MechanicalJointAccessories
Size valve* D-150
Mechanical
Joint
Gland
D-150
Mechanical
Joint
Gland
with
Bonding
Screws
D-150
Plain
Gasket
D-150
Duck Tipped
Gasket
4"160519186610194738194732
6"160520186611194739194733
8"160521186612194740194734
10"160522186613194741194735
12"160523186614194742194736
Part No.
Part No.
Part No.
Part No.
Size valve *Part Number
4"195204
6"195205
8"195206
10"195207
12"195208
14"348510
16"199946
Size valve *Part Number
2"195290
2-1/2"195291
3"195292
4"195293
6"195294
8"195375
Size valve *Part Number
2"280035
3"280036
4"280037
4"*280042 **
6"280037
6"*280042 **
8"280038
8"*280043 **
10"280038
10"*280043 **
12"280038
12"*280043 **
14"280038
16"280039
18"280039
20"280039
24"280040
30"280041
36"280041
Rev. 2-06
GATE VALVE CONNECTION ACCESSORIES
Accessory Kits
NOTE: Basic kits listed here. Contact MUELLER Customer Service Center
regarding the many options available.
Gland Packs
Mechanical Joint Accesories
Slip - on Gaskets
Radial Compression Gaskets
Gland Packs
D-150 Mechanical Joint Accessories
* Nominal
** Anti-rotation bolts
“T” Head Bolts and Nuts (size supplied will be appropriate
for size of valve) - specify quantity
DOUBLE-DISC
Valve sizeConversion kit part
number
2"181338
3"181393*
4"181340
6"181341
8"181342
10"181343
12"181344
14"181388
16"181389
18"181390
20"181391
24"181392
GATE VALVE OPTIONS
Double-Disc Gate Valve Options
Rollers, Tracks and Scrapers (Double-disc gate valves only)
Double-disc gate valves in sizes 16" through 36" for vertical installations are furnished with a shoe on each side of the disc assembly for
guiding the disc assembly throughout its entire travel. Gate valves in
sizes 16" through 36" for horizontal installations are furnished with
rollers which travel on a bronze track in the body and bonnet. These
rollers support the weight of the disc assembly throughout its entire
travel. The roller carriage has scrapers for cleaning the track ahead of
the rollers. Rollers and tracks are required on 16" and larger doubledisc gate valves when the main valve stem is horizontal. They are not
required on bevel geared valves specified for vertical installation.
O-ring conversion kit contains the
following
❏ (1) G-70 Stuffing box
❏ (2) G-48 O-rings
❏ (1) G-32 Stuffing box gasket
❏ G-41 bolts and nuts
(2) for 2" valve
(4) for 3"-14" valves
(6) for 16"-24" valves
10.41
Rev. 2-06
Double disc gate valve o-ring
conversion kit
MUELLER CO. offers kits to
convert non-rising stem conventionally packed gate valves to
O-ring sealed type. The conversion replaces the conventional
packing with two O-ring seals
above the thrust collar and a
gasket seal between the bonnet
and new stuffing box.
*1956 Design. For valves made prior to 1956 use kit number 181339
10.40
Catalog number
suffix
DescriptionValve size
Without
indicator
With
indicator
02102Bevel gearing**4" and larger
03103Spur gearing**4" and larger
06106Bevel gearing and bypass18"-48"
07107Spur gearing and bypass18"-48"
09-Bypass only18"-24"
-
-108
Position indicator only
4"-48"
Valve size/typeBypass valve size
18"-20" RW2"
24" RW2-1/2"
30", 36" RW3"
42", 48" RW
4"
14"* DD
2"
16" - 20" DD3"
24", 30" DD4"
36" DD
6"
Rev. 9-09 Shaded area indicates change.
Resilient Wedge Options
Clean out Port Option on 24"-48" RWGV
Cleanout port option is available for
24"- 48" resilient wedge gate valves.
24" valves would utilize a 1-1/2" port
while 30-48" valves utilize a 2” port.
Please refer to option 202 (i.e.
240A236106LN202) when ordering.
RESILIENT WEDGE AND
DOUBLE-DISC GATE VALVE OPTIONS
Resilient Wedge and Double-Disc Gate Valve Options
Needle and Slot (Universal) Position Indicator
Can be furnished on 4" and larger non-rising stem valves with or
without gearing. Mechanism is fully enclosed and uses a moving
pointer on a scale to show relative position of valve gate.
Stainless Steel External Fasteners
Stainless steel (type 304 or 316) external fasteners are available.
Note: Resilient Wedge Gate Valves throught 12" have stainless steel
type 304 fasteners as standard.
Gearing
Non-rising stem gate valves 4" and larger can be furnished with bevel
gearing, or 14" and larger with spur gearing (for double-disc valves,
does not apply to 14"). Gearing is recommended for all resilient
wedge gate valves 30" and larger, and for all double-disc gate valves
24" and larger. Gearing provides an additional bearing to support
the extreme end of the valve stem. Bevel and spur gearing includes a
grease case. All gears have machine cut teeth. Bevel geared valves are
for horizontal installation and spur geared valves for vertical. Styles
shown are typical – actual appearance may vary.
2" Square Wrench Nut or Handwheel
The 2" square wrench nut is standard on all N.R.S. resilient wedge
and double-disc gate valves except flange x flange and thread x thread
valves, which have a handwheel as standard. The wrench nut and
handwheel are optional alternatives to these standard features.
How to order
Spur Gearing
with Grease case
Bevel Gearing
with Grease case
N.R.S. Bypass
N.R.S. Bypass
Bypass valves are AWWA non-rising stem type. On resilient wedge
valves, the bypass valve is also the RW type. On double-disc valves,
it is the DD type. Bevel geared or horizontally installed valves have
the bypass mounted on the bottom end of the valve. Spur geared or
vertically installed valves have the bypass mounted on the disc of the
valve body.
Available on 18"-48" Gate Valves Only.
Accessories are ordered by adding a suffix number to the basic gate
valve catalog number. See chart below for accessory suffix numbers.
Catalog number for options*
*Fasteners, coatings, operators and other options not included in this chart are
ordered by including them in the valve specification notations.
**Includes grease case. Not available for 14" double-disc gate valves.
14" - 36" DOUBLE-DISC
Dimension*Nominal Size
14"16"18"
20"
24"30"36"
A
34.1239.0043.00
47.50
55.7566.50**
FF
15.0019.7521.00
21.50
23.5028.0031.00
L
3.503.503.50
3.50
3.504.004.00
N
20.3122.5624.83
27.08
31.5839.12
46.00
O (number and size of holes)
10--7/812--7/812--7/8
14--7/8
16--7/820--1-1/8
24--1-1/8
DD
8.0012.7514.00
14.50
16.5020.00
23.00
Q (bore)
14.0016.0018.00
20.00
24.0030.00
36.00
Turns to open
465359
65
7765
78
Weight*
80511081488
1810
26055100
8300
OO (bolt circle diameter)
18.7521.0023.25
25.50
30.0036.88
43.75
GATE VALVES - M.J. x M.J.
10.39
Rev. 2-06
*All dimensions are in inches. All weights are in pounds and are approximate.
**36" valves sold only with gear operators, dimension depends on style of operator selected. Contact Customer Service for Dimension.
Options
See pages 10.40 and 10.41 for more information on Gate Valve options.
❏ Bevel gearing with grease case ❏ Position indicators ❏ Tracks, rollers, scrapers
❏ Spur gearing with grease case ❏NRS by-pass valve ❏ MUELLER HP® Epoxy Coating
❏ Stainless steel fasteners ❏ Bronze internal parts ❏ Handwheel
❏ ASTM B98-C66100/H02 stem and disc pins
ASTM B763-C99500 Stem 18" - 36"
10.38
Double-disc gate valve parts
Catalog
Part No.
DescriptionMaterialMaterial standard
G-15Bonnet gasketCompositionASTM D1170
G-16Bonnet bolts & nutsSteelANSI B18.2 plated
G-18Seat ringBronzeASTM B62
G-19Disc and disc ringCast iron *ASTM A126 CL.B
G-20Disc pinBronzeASTM B21
G-21Side spreaderBronzeASTM B62
G-22Bottom wedgeCast ironASTM A126 CL.B
G-24Test plugIron
G-26Nut for wrench nutSteelANSI B18.2 plated
G-32Stuffing box gasketFiber
G-37Top wedge nutCast iron *ASTM A126 CL.B
G-38Wrench nutCast ironASTM A126 CL.B
G-41Stuffing box bolt & nutSteelANSI B18.2 plated
G-42StemBronzeASTM B584**
G-43BonnetCast ironASTM A126 CL.B
G-45Hand wheelCast ironASTM A126 CL.B
G-47BodyCast ironASTM A126 CL.B
G-48Stuffing box O-ringRubber
G-49Stem O-ringRubber
G-50Stuffing boxCast ironASTM A126 CL.B
14" - 36" DOUBLE-DISC NRS
Rev. 2-06
❏ Catalog number–
A-2380-20 standard mechanical joint ends (with accessories unassembled)
A-2380-22 standard mechanical joint ends (with accessories and bonding set screws in glands
unassembled)
A-2380-23 standard mechanical joint ends (less accessories)
❏ Sizes - 14", 16", 18", 20", 24", 30", 36"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C500 Standard
❏ Mechanical joint ends comply with ANSI/AWWA C111 Standard
❏ Iron body - bronze mounted
❏ Double disc parallel seat with four point wedging mechanism
❏ Non-rising stem (NRS)
❏ O-ring sealed stuffing box
❏ 2" square wrench nut (handwheel optional)
❏ 30" & 36" sizes – 150 psig (1034 kPa) maximum working pressure,
300 psig (2068 kPa) test pressure
GATE VALVES - STANDARD M.J. x M.J.
** Cast iron discs with rolled-in bronze facings; cast iron top wedge nut with integrally
cast bronze bushing.
***18" - 36" ASTM B583
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
A-2380-20
30" & 36" DOUBLE-DISC
Dimension*Nominal Size
30"36"
A66.50**
L4.004.00
OO (bolt circle diameter)36.8843.75
Q (bore)30.0036.00
R38.7546.00
UU36.0042.75
XX24.3827.50
FF28.3831.50
B (number and size of holes for FL)28--1-3/832--1-5/8
Turns to open6578
Weight*51008300
N39.1246.00
O (number and size of holes for MJ)20--1-1/824--1-1/8
GATE VALVES - FL. x M.J.
10.37
Rev. 2-06
*All dimensions are in inches. All weights are in pounds and are approximate.
**36" valves sold only with gear operators, dimension depends on style of operator selected. Contact Customer Service for Dimension.
Options
See pages 10.40 and 10.41 for more information on Gate Valve options.
❏ Bevel gearing with grease case ❏Position indicators ❏Tracks, rollers, scrapers
❏ Spur gearing with grease case ❏NRS by-pass valve ❏MUELLER HP® Epoxy Coating
❏ Stainless steel fasteners ❏Bronze internal parts ❏Handwheel
❏ ASTM B98-C66100/H02 disc pins
ASTM B763-C99500 stem
10.36
Double-disc gate valve parts
Catalog
Part No.
DescriptionMaterialMaterial standard
G-15Bonnet gasketCompositionASTM D1170
G-16Bonnet bolts & nutsSteelANSI B18.2 plated
G-18Seat ringBronzeASTM B62
G-19Disc and disc ringCast iron *ASTM A126 CL.B
G-20Disc pinBronzeASTM B21
G-21Side spreaderBronzeASTM B62
G-22Bottom wedgeCast ironASTM A126 CL.B
G-24Test plugIron
G-26Nut for wrench nutSteelANSI B18.2 plated
G-32Stuffing box gasketFiber
G-37Top wedge nutCast iron *ASTM A126 CL.B
G-38Wrench nutCast ironASTM A126 CL.B
G-41Stuffing box bolt & nutSteelANSI B18.2 plated
G-42StemBronzeASTM B584**
G-43BonnetCast ironASTM A126 CL.B
G-45Hand wheelCast ironASTM A126 CL.B
G-47BodyCast ironASTM A126 CL.B
G-48Stuffing box O-ringRubber
G-49Stem O-ringRubber
G-50Stuffing boxCast ironASTM A126 CL.B
30" & 36" DOUBLE-DISC NRS
Rev. 2-06
❏ Catalog number–
A-2380-16 flanged x mechanical joint (with accessories unassembled)
A-2380-18 flanged x mechanical joint (accessories and bonding set screws in gland unassembled)
A-2380-19 flanged x mechanical joint (less accessories)
❏ Sizes - 30" & 36"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C500 Standard
❏ Flange ends comply with ANSI B16.1, Class 125
❏ Mechanical joint ends comply with ANSI/AWWA C111 Standard
❏ Iron body - bronze mounted
❏ Double disc parallel seat with four point wedging mechanism
❏ Non-rising stem (NRS)
❏ O-ring sealed stuffing box
❏ 2" square wrench nut (handwheel optional)
❏ 150 psig (1034 kPa) maximum working pressure,
300 psig (2068 kPa) test pressure
GATE VALVES - STANDARD FL. x M.J.
** Cast iron discs with rolled-in bronze facings; cast iron top wedge nut with integrally
cast bronze bushing.
***18" - 36" ASTM B583
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
A-2380-16
14"-36" DOUBLE-DISC NRS
Dimension*Nominal Size
14"16"18"
20"
24"30"36"
A
34.1239.0043.00
47.50
55.7566.50**
FF
15.0020.2522.00
22.25
25.5028.7532.00
R
21.0023.5025.00
27.50
32.0038.7546.00
T
9.00N/AN/A
N/A
N/AN/AN/A
U
3.00N/AN/A
N/A
N/AN/AN/A
UU (bolt circle diameter)
18.7521.2522.75
25.00
29.5036.0042.75
B (number and size of holes)
12--1-1/816--1-1/816--1-1/4
20--1-1/4
20--1-3/828--1-3/832--1-5/8
Max. tap size
2N/AN/A
N/A
N/AN/AN/A
Turns to open
465359
65
776578
Q (bore)
14.0016.0018.00
20.00
24.0030.0036.00
GATE VALVE - FL. x FL.
10.35
Rev. 2-06
*All dimensions are in inches. All weights are in pounds and are approximate.
**36" valves sold only with gear operators, dimension depends on style of operator selected. Contact Customer Service for Dimension.
Options
See pages 10.40 and 10.41 for more information on Gate Valve options.
❏ Bevel gearing with grease case ❏NRS by-pass valve
❏ Spur gearing with grease case ❏2" Square wrench nut
A - Bevel Gear**34.0037.3844.5047.6954.0664.9377.1990.75102.61
Turns to open
Turns to open
Turns to open
Weight*650931122214942352510084001330019700
*All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing.
**Center line of operating nut to center line of valve.
†Spur or Bevel Gear must be used with 30", 36", 42", 48" valves.
††Turns shown for Bevel gearing. Valves with Bevel gearing: 14" and 16" - 2:1 ratio, 18"-48" - 4:1 ratio.
*All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing.
**Center line of operating nut to center line of valve.
†Spur or Bevel Gear must be used with 30", 36", 42", 48" valves.
††Turns shown for Bevel gearing. Valves with Bevel gearing: 14" and 16" - 2:1 ratio, 18"-48" - 4:1 ratio.
A - Bevel Gear**34.0037.3844.5047.6954.0664.9377.1990.75102.61
Turns to open
Turns to open
Turns to open
Weight*659841123015072398510084001330019700
*All dimensions are in inches. All weights are in pounds and are approximate. Weights for 30"-48" valves are with gearing; for all others without gearing.
**Center line of operating nut to center line of valve.
†Spur or Bevel Gear must be used with 30", 36", 42", 48" valves.
††Turns shown for Bevel gearing. Valves with Bevel gearing: 14" and 16" - 2:1 ratio, 18"-48" - 4:1 ratio.
❏ Iron body with nominal 10 mils MUELLER® Pro-Gard™ Epoxy Fusion Coated
interior and exterior surfaces
❏ Epoxy coating meets or exceeds all applicable requirements o
ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber;
no exposed iron
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring
serving as dirt seal††
❏ 2" square wrench nut (optional handwheel available) – open left or open right
❏ 250 psig (1723 kPa) maximum working pressure,
500 psig (3447 kPa) static test pressure
❏ 2 1/2" - 8" sizes – UL Listed, FM Approved: 200 psig (1379 kPa)
††Dirt seal on 4"-8" valves
GATE VALVES - RAD. x RAD
A-2360-37
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
❏ Position indicators ❏Stainless steel fasteners: Type 316
❏ ASTM B98-C66100/H02 stem ❏Handwheel
* Fully encapsulated in molded rubber with no iron exposed
** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with
††Dirt seal on 4"-8" valves
additional bolts (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal
when ordering a replacement gasket or O-ring.
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
G-49
G-200
G-207
G-41
G-201
G-208
G-203
G-210**
G-16
G-211**
G-205
G-212**
G-209
G-206
4"-12" A-2360 RESILIENT WEDGE
Dimension*Nominal size
4"6"8"10"12"
A14.1918.0021.5025.5028.62
Q (bore)4.306.308.3010.3012.30
L4.124.385.625.625.62
R9.0011.0013.5016.0019.00
UU (bolt circle diameter for FL)7.509.5011.7514.2517.00
B (number and size of holes for FL)8--.758--.888--.8812--1.0012--1.00
FF
Turns to open1420.526.53338.5
Weight*90165260400565
Dimensions
W
(distance between strapping lug holes across face of valve ends)
8.62
10.6213.12
16.3818.12
10.91
12.6614.69
15.7216.31
A
FF
UU
R
L
B
Q
W
GATE VALVE - SL. x FL.
10.19
Rev. 2-06
*All dimensions are in inches. All weights are in pounds and are approximate.
10.18
Rev. 9-09 Shaded area indicates change.
4"-12" A-2360 RESILIENT WEDGE
GATE VALVES - SL. x FL.
❏ Catalog number–
A-2360-41 Slip-on† end (with gasket) x flange end
A-2360-43 Slip-on† end (less gasket) x flange end
❏ Sizes – 4", 6", 8", 10", 12"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard, UL Listed,
FM Approved, and certified to ANSI/NSF 61.
❏ Slip-on ends fit plain end of classes 150, 200 and 250 cast iron, ductile iron and classes 150
and 200 cast iron O.D. PVC
❏ Flange end dimensions and drilling comply with ANSI B16.1, class 125
❏ Iron body with nominal 10 mils MUELLER® Pro-Gard™ Epoxy Fusion Coated interior and
exterior surfaces
❏ Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard
and is certified to ANSI/NSF 61
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber;
no exposed iron
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring
serving as dirt seal
❏ 2" square wrench nut (optional handwheel available) – open left or open right
❏ 250 psig (1723 kPa) maximum working pressure,
500 psig (3447 kPa) static test pressure
❏ UL Listed, FM Approved: 200 psig (1379 kPa)
†Design and dimensions of the joint are manufactured under license of U.S. Pipe and Foundry Company.
A-2360-41
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
❏ Position indicators ❏Stainless steel fasteners: Type 316
G-210**BonnetCast Iron ♦ASTM A126 CL.B
G-211**Bonnet O-ringNitrite
G-212**BodyCast Iron ♦ASTM A126 CL.B
* Fully encapsulated in molded rubber with no iron exposed
** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with
additional bolts (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal
when ordering a replacement gasket or O-ring.
††Dirt seal on 4"-12" valves
♦Body and bonnet of 12" valves are ductile iron standard wall thickness in compliance with C509.
Cast Iron*
Rubber
ASTM A126 CL.B
G-49
G-200
G-207
G-41
G-201
G-208
G-203
G-210**
G-16
G-211**
G-205
G-212**
G-209
G-206
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
4"-12" A-2360 RESILIENT WEDGE
Dimension*Nominal size
4"6"8"10"12"
A14.1918.0021.5025.5028.62
L2.502.502.502.502.50
N9.1211.1213.3715.6217.88
O (number and size of holes for MJ)4--.886--.886--.888--.888--.88
Q (bore)4.306.308.3010.3012.30
OO (bolt circle diameter for MJ)7.509.5011.7514.0016.25
R9.0011.0013.5016.0019.00
UU (bolt circle diameter for FL)7.509.5011.7514.2517.00
FF9.5011.0012.0013.8814.44
B (number and size of holes for FL)8--.758--.888--.8812--1.0012--1.00
Turns to open1420.526.53338.5
Weight*115168275400570
Dimensions
GATE VALVE - M.J. x FL.
10.13
Rev. 2-06
* All dimensions are in inches. All weights include accessories are in pounds and are approximate.
10.12
Rev. 9-09 Shaded area indicates change.
4"-12" A-2360 RESILIENT WEDGE
GATE VALVES - M.J. x FL.
❏ Catalog number–
A-2360-16 mechanical joint x flanged ends (with accessories unassembled)
A-2360-19 mechanical joint x flanged ends (less accessories)
❏ Sizes – 4", 6", 8", 10", 12"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C509 Standard,
UL Listed, FM Approved, and certified to ANSI/NSF 61.
❏ Flanged end dimensions and drilling comply with ANSI B16.1, class 125
❏ Mechanical joint end complies with ANSI/AWWA C111 Standard
❏ Iron body with nominal 10 mils MUELLER® Pro-Gard™ Fusion Epoxy Coated interior
and exterior surfaces
❏ Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550
Standard and is certified to ANSI/NSF 61
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber;
no exposed iron
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper &1 lower O-rings), with fourth
O-ring serving as dirt seal
❏ 2" square wrench nut (optional handwheel available) – open left or open right
❏ 250 psig (1723 kPa) maximum working pressure,
500 psig (3447 kPa) static test pressure
❏ UL Listed, FM Approved – 200 psig (1379 kPa)
A-2360-16
M.J. accessories
shipped unassembled
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
❏ Position indicators ❏ Stainless steel fasteners: Type 316
G-210**BonnetCast Iron ♦ASTM A126 CL.B
G-211**Bonnet O-ringNitrite
G-212**BodyCast Iron ♦ASTM A126 CL.B
* Fully encapsulated in molded rubber with no iron exposed
** Previous to 1999 these parts on 4"-12" valves were designed with a gasket instead of an O-ring and with
additional bolts (2"-3" sizes retain neoprene gasket design affecting these parts). Confirm the type of seal
when ordering a replacement gasket or O-ring.
††Dirt seal on 4"-12" valves
♦Body and bonnet of 12" valves are ductile iron standard wall thickness in compliance with C509.
Cast Iron*
Rubber
ASTM A126 CL.B
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
4"-12" A-2361 RESILIENT WEDGE GATE
A
N
L
FF
Q
OO
O
F
KK
M
G
Dimension*Nominal size
4"6"
A14.1918.00
L2.502.50
M4.907.00
N9.1211.12
O (number and size of holes for MJ)4--.886--.88
Q4.306.30
OO (bolt circle diameter for MJ)7.509.50
KK2.753.75
FF11.3413.31
Turns to open1420.5
Weight*108169
Dimensions
F3.703.70
G (number and size of holes for Aqua-Grip)4--.884--.88
8"
21.50
2.50
9.15
13.37
6--.88
8.30
11.75
3.75
14.72
26.5
294
3.70
6--.88
10"
25.50
2.50
11.20
15.62
8--.88
10.30
14.00
3.75
16.41
33.0
395
3.89
8--.88
12"
28.62
2.50
13.30
17.88
8--.88
12.30
16.25
3.75
16.89
38.5
565
3.89
8--.88
VALVE WITH AQUA-GRIP™ x MJ. ENDS
10.9
Rev. 2-06
*All dimensions are in inches. All weights are in approximate pounds.
10.8
Resilient wedge gate valve parts
Catalog
Part
No.
DescriptionMaterialMaterial standard
G-16Bonnet Bolts & NutsStainless Steel
Type 304
G-41Stuffing Box Bolts & NutsStainless Steel Type 304
G-216End ring**Ductile Iron
G-217Breakaway nut w/washer*** Steel
G-218T-head Bolt***Steel
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
Stainless Steel
Type 304
Rev. 2-06 Shaded area indicates change.
4"-12" A-2361 RESILIENT WEDGE GATE
VALVE WITH AQUA-GRIP™ x MJ. ENDS
❏ Catalog number–
A-2361-78 Aqua-Grip ends x mechanical joint for DIPS pipe in sizes 4", 6", 8", 10", 12"
A-2361-88 Aqua-Grip ends x mechanical joint for IPS pipe in sizes 4", 6", 8"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed,
FM Approved, and certified to ANSI/NSF 61.
❏ Ductile Iron body and bonnet with nominal 10 mils MUELLER® Pro-Gard™ Fusion Epoxy Coated
interior and exterior surfaces.
❏ Epoxy coating meets or exceeds all applicable requirements of ANSI/AWWA C550 Standard and
is certified to ANSI/NSF 61.
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber;
no exposed iron.
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving
as dirt seal
❏ 2" square wrench nut (optional handwheel available) – open left or open right
❏ 250 psig (1723 kPa) maximum working pressure, 500 psig (3447 kPa) static test pressure
❏ UL Listed, FM Approved – 200 psig (1379 kPa)
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
A-2361-78
❏ Position indicators ❏ Stainless steel fasteners: Type 316
❏ ASTM B98-C66100/H02 stem ❏ Handwheel
*Fully encapsulated in molded rubber with no iron exposed.
**Parts for Aqua-Grip connection not shown – one required for each Aqua-Grip connection.
***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection.
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
G-49
G-202
G-200
G-207
G-41
G-201
G-208
G-203
G-210
G-16
G-211
G-205
G-212
G-209
G-206
A
F
FF
KK
G
4"-12" A-2361 RESILIENT WEDGE GATE
Dimension*Nominal size
4"6"8"
A14.1918.0021.50
F3.703.703.70
Turns to open1420.526.5
Weight*119162256
Dimensions
FF12.6815.1216.94
KK2.753.753.75
G (number and size of holes for Aqua-Grip)4--.884--.886--.88
10"
25.50
3.89
33.0
380
18.06
3.75
8--.88
12"
28.62
3.89
38.5
475
18.90
3.75
8--.88
VALVE WITH AQUA-GRIP™ x AQUA-GRIP™ ENDS
10.7
Rev. 2-06
*All dimensions are in inches. All weights are in approximate pounds.
10.6
Resilient wedge gate valve parts
Catalog
Part
No.
DescriptionMaterialMaterial standard
G-16Bonnet Bolts & NutsStainless Steel
Type 304
G-41Stuffing Box Bolts & NutsStainless Steel Type 304
G-216End ring**Ductile Iron
G-217Breakaway nut w/washer*** Steel
G-218T-head Bolt***Steel
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
Stainless Steel
Type 304
Rev. 2-06 Shaded area indicates change.
VALVE WITH AQUA-GRIP™ x AQUA-GRIP™ ENDS
4"-12" A-2361 RESILIENT WEDGE GATE
❏ Catalog number–
A-2361-77 Aqua-Grip ends x Aqua-Grip ends for DIPS pipe in sizes 4", 6", 8", 10", 12"
A-2361-87 Aqua-Grip ends x Aqua-Grip ends for IPS pipe in sizes 4", 6", 8"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard,
UL Listed, FM Approved, and certified to ANSI/NSF 61.
❏ Ductile Iron body and bonnet with nominal 10 mils MUELLER® Pro-Gard
™
Fusion Epoxy Coated interior and exterior surfaces
❏ Epoxy coating meets or exceeds all applicable requirements of
ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving
as dirt seal
❏ 2" square wrench nut (optional handwheel available)–-open left or open right
❏ 250 psig (1723 kPa) maximum working pressure,
500 psig (3447 kPa) static test pressure
❏ UL Listed, FM Approved – 200 psig (1379 kPa)
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
A-2361-77
❏ Position indicators ❏ Stainless steel fasteners: Type 316
❏ ASTM B98-C66100/H02 stem ❏ Handwheel
*Fully encapsulated in molded rubber with no iron exposed.
**Parts for Aqua-Grip connection not shown – one required for each Aqua-Grip connection.
***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection.
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
G-49
G-202
G-200
G-207
G-41
G-201
G-208
G-203
G-210
G-16
G-211
G-205
G-212
G-209
G-206
Dimension*Nominal size
4"6"10"
A14.1918.0025.50
B (number and size of holes for FL)8--.888--.8812--1.00
R9.0011.0016.00
UU (bolt circle diameter for FL)7.509.5014.25
Turns to open1420.533.0
Weight*107149365
Dimensions
F3.703.703.89
KK2.753.753.75
G (number and size of holes for Aqua-Grip)4--.884--.888--.88
8"
21.50
8--.88
13.50
11.75
26.5
225
3.70
3.75
6--.88
12"
28.62
12--1.00
19.00
17.00
38.5
450
3.89
3.75
8--.88
FF10.8412.8115.53
14.2216.45
Q (Bore)4.306.3010.30
8.3012.30
T.78.931.06
.931.00
A
R
F
UU
B
KK
G
T
FF
Q
4"-12" A-2361 RESILIENT WEDGE
GATE VALVE WITH AQUA-GRIP™ x FL. ENDS
10.5
Rev. 2-06
*All dimensions are in inches. All weights are in approximate pounds.
10.4
Resilient wedge gate valve parts
Catalog
Part
No.
DescriptionMaterialMaterial standard
G-16Bonnet Bolts & NutsStainless Steel
Type 304
G-41Stuffing Box Bolts & NutsStainless Steel Type 304
G-216End ring**Ductile Iron
G-217Breakaway nut w/washer*** Steel
G-218T-head Bolt***Steel
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
ASTM A536 Grade 65-45-12
Stainless Steel
Type 304
Rev. 2-06 Shaded area indicates change.
GATE VALVE WITH AQUA-GRIP™ x FL. ENDS
4"-12" A-2361 RESILIENT WEDGE
❏ Catalog number–
A-2361-76 Aqua-Grip ends x flanged ends for DIPS pipe in sizes 4", 6", 8", 10", 12"
A-2361-86 Aqua-Grip ends x flanged ends for IPS pipe in sizes 4", 6", 8"
❏ Meets or exceeds all applicable requirements of ANSI/AWWA C515 Standard, UL Listed,
FM Approved, and certified to ANSI/NSF 61.
❏ Flanged end dimensions and drilling comply with ANSI B16.1, class 125
❏ Ductile Iron body and bonnet with nominal 10 mils MUELLER® Pro-Gard
™
Fusion Epoxy Coated interior and exterior surfaces
❏ Epoxy coating meets or exceeds all applicable requirements of
ANSI/AWWA C550 Standard and is certified to ANSI/NSF 61
❏ Iron wedge, symmetrical & fully encapsulated with molded rubber; no exposed iron
❏ Non-rising stem (NRS)
❏ Triple O-ring seal stuffing box (2 upper & 1 lower O-rings), with fourth O-ring serving
as dirt seal
❏ 2" square wrench nut or handwheel available – open left or open right
❏ 250 psig (1723 kPa) maximum working pressure,
500 psig (3447 kPa) static test pressure
❏ UL Listed, FM Approved – 200 psig (1379 kPa)
A-2361-76
Options
See page 10.40 for more information on Resilient Wedge Gate Valve options
❏ Position indicators ❏ Stainless steel fasteners: Type 316
❏ ASTM B98-C66100/H02 stem ❏ Handwheel
*Fully encapsulated in molded rubber with no iron exposed.
**Parts for Aqua-Grip connection not shown – one required for each Aqua-Grip connection.
***Not shown. See dimension drawing on next page for number require for each size Aqua-Grip connection.
SEE PAGE 10.43 FOR ORDERING INSTRUCTIONS
G-49
G-202
G-200
G-207
G-41
G-201
G-208
G-203
G-210
G-16
G-211
G-205
G-212
G-209
G-206
10.3
Rev. 2-06
10.2
2361 SERIES RESILIENT WEDGE VALVES
Rev. 9-09 Shaded area indicates change.
MUELLER® 2361 SERIES RESILIENT WEDGE GATE VALVES
WITH AQUA-GRIP™ SYSTEM
The Mueller® Aqua-Grip™ System is offered in 4" through 12" sizes of the Mueller 2361 Series Resilient Wedge Gate Valves.
This Mueller exclusive combines both the compression connection and the pipe restraint system in one convenient, quick installation package. This eliminates the need for anchor couplings, tie rods or separate gland-type restrains. A typical Aqua-Grip
connection uses fewer bolts than a conventional mechanical joint end, and substantially fewer than a gland-type restraint, significantly reducing installation time. This “labor saving” system is also available on Mueller Centurion® Fire Hydrants, and as
separate couplings and fittings to compliment water main installation needs.
WITH MUELLER® AQUA-GRIP™ SYSTEM
❏ACCEPTS VARIED TYPES OF PIPE – DIPS style
fits DI, C900 PVC and DIPS PE pipe. IPS style fits
PVC, IPS PE. No disassembly or adapters, no special
pipe end preparation, and no liner for PE pipe (DR9DR17) required.
❏FULLY ASSEMBLED STAB CONNECTION – arrives ready
to insert the pipe, tighten the bolts and it’s done. No need to
change-out, add or remove parts. Nothing additional to inventory or handle in the field. No extra bolts to assemble or tighten.
Substantially reduces labor and inventory costs.
❏VISUALLY SHOWS WHEN PROPERLY TIGHTENED – break-
away nuts snap off using a standard wrench. No special torque
requirements. Inner nut remains in place to allow future access to
connection, if required. Reduces crew training and saves installation time. (In illustration, lower nut shown before tightening, upper
one after.)
❏PRESSURE RESPONSIVE O-RING
SEAL – a double O-ring uses hydrostatic
pressure from inside the pipe to enhance
the seal as line pressure increases.
❏FULL CIRCUMFERENTIAL
RESTRAINT – gripper ring encircles
pipe for uniform grip without creating
points of high stress in pipe wall that
could contribute to pipe failure.
❏INSTALLS IN WET CONDITIONS –
no special field conditions required, even
installs under water.
❏DUCTILE IRON CONSTRUCTION –
valve body, bonnet and the Aqua-Grip
System components.
❏PLUS ALL THE OTHER FEATURES
OF THE 2300 SERIES VALVES
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.