Muddy MSB100 Instruction Manual
INSTRUCTION MANUAL
The Ultra-Steady
Bench
Model MSB100
January 2018 . Published by Premier Outdoor Equipment, LLC., Windom, Minnesota.
© 2018 Premier Outdoor Equipment, LLC. All rights reserved.
PO Box 454 • Windom, MN 56101 • (844) 745-7723
www.GoMuddy.com
2
Front Leg-Upper
Front Leg-Lower
A
G
G
A
D
C
C
C
F
D
A
Platform Support
Rear Leg
Upper
Rear
Brace
Delta
Bolt
Rear Leg-Lower
Platform Brace
Male
Platform Brace
Detent Button
Female
Platform Brace
MSB100 Ultra-Steady Bench
WARNING: Do not use without
securing rear brace to the rear leg using
provided delta bolt. (see fig. 1) Keep
ngers away from pivot points between
back and front legs to prevent pinching.
Failure to follow these instructions may
result in serious injury!
Parts List (MSB100)
Part# Description Qty
UP17-0011 Shooting Platform 1
UP15-0351 Seat Cushion 1
UP18-0013 Seat Support 1
UP18-0014 Platform Support 1
UP18-0015 Front Leg-Lower 1
UP18-0016 Front Leg-Upper 1
UP18-0017 Rear Leg-Lower 1
UP18-0018 Rear Leg-Upper 1
UP18-0019 Rear Brace 1
UP18-0020 Male Platform Brace 1
UP18-0021 Female Platfrom Brace 1
UP10-0586 Gun Rest-Upper 1
UP10-0587 Gun Rest-Lower 1
Instruction Maunal 1
UP77-0019 [A] 1/4" x 1 1/2" Hex Bolt 7
UP77-0023 [B] 1/4" x 2" Hex Bolt 3
UP77-0039 [C] 5/16" x 1 3/4" Hex Bolt 4
UP77-0041 [D] 5/16" x 2" Hex Bolt 2
UP77-0047 [E] 5/16" x 2 3/4" Hex Bolt 1
UP77-0048 [F] 5/16" x 3" Hex Bolt 1
UP77-0209 [G] 5/16'' x 4 1/2'' Hex Bolt 2
UP77-0192 5/16'' x 3'' Delta Bolt 1
UP77-0029 5/16" Nylock Nut 10
UP77-0001 1/4" Nylock Nut 3
UP77-0030 Nylon Washer 35
UP77-0054 3/8" Wing Nut 1
UP77-0063 1/2" Wing Nut 1
Check to make sure you have all the required
parts and hardware. If you nd damaged or
missing parts in a newly purchased product,
please return this product to the retailer for
replacement.
STEP 1. Using (3) 1/4'’ x 1 1/2'’ hex bolts [A], (6) nylon washers and (3) 1/4'’ nylock nuts
attach the front leg-lower piece to the front leg-upper piece. Then, attach the assembled
front leg to the platform support using (2) 5/16'’ x 2'’ hex bolts [D], (4) nylon washers
and (2) 5/16'’ nylock nuts.
STEP 2. Using (2) 5/16'’ x 4 1/2'’ hex bolts [G], (4) nylon washers and (2) 5/16'’ nylock nuts
attach the rear leg-lower piece to the rear leg-upper piece. Then, attach the assembled
rear leg to the platform support using (1) 5/16'’ x 3'’ hex bolt [F], (2) nylon washers and
(1) 5/16'’ nylock nut.
STEP 3. Connect the male platform brace to the female platform brace. Then, attach the
assembled platform brace to the front leg and rear leg using (2) 5/16'’ x 1 3/4'’ hex bolts
[C], (6) nylon washers and (2) 5/16'’ nylock nuts.
STEP 4. Using (1) 5/16'’ x 1 3/4'’ hex bolt [C], (2) nylon washers and (1) 5/16'’ nylock nut
secure the rear brace to platform support. Next, align holes in the rear brace and rear
leg using the delta bolt to secure.
Loading...