MTX Audio 622CM, 822CM User Manual

1 Mitek Plaza
Winslow, IL 61089
815-367-3000 800-225-5689
MODEL 622CM / MODEL 822CM OWNER'S MANUAL
21A6502
CONGRATULATIONS
We appreciate your choice of MTX In-Ceiling Speakers. Properly installed and operated, MTX In-Ceiling Speakers should provide years of worry-free listening pleasure. It’s important that you follow each step in this guide carefully to insure proper installation.
SPECIFICATIONS MODEL 622CM MODEL 822CM
Frequency Response 64Hz-20kHz 40Hz-20kHz ±3dB ±3dB
Impedance 8 ohms nominal 8 ohms nominal
Power Handling 35 Watts RMS 45 Watts RMS 70 Watts Peak 90 Watts Peak
Music Music
Sensitivity (1W/1m) 84dB 84dB
Woofer Diameter 6-1/2” 8”
Tweeter (2) 1/2" Balanced (2) 1/2" Balanced Dome Dome
MTX WARRANTY INFORMATION
All MTX In-Ceiling Speakers purchased in the United States from an authorized MTX dealer are guaranteed against defects in material and workmanship for a period ten years from the date purchased by the end user, and limited to the original retail pur­chaser of the product.
MTX disclaims any liability for other incurred damages resulting from product defects. Any expenses incurred in the removal and reinstallation of product is not covered by this warranty. MTX's total liability will not exceed the purchase price of the product. This warranty is valid in the United States only.
Proof of purchase is required when requesting service, so please retain your sales receipt and take a moment to register your warranty on line at www.mtx.com.
Mounting Depth 3-5/16" 3-3/4"
Baffle Diameter 9" 10-3/4"
PAINTING YOUR MTX IN-CEILING SPEAKERS
MTX In-Ceiling Speakers are designed to accept all types of interior and exterior paints. Spray or roller application should provide excellent results. A paint shield is included with all MTX In-Ceiling Speakers to protect the speakers during the painting process.
R+
R-
L-
L+
OTHER PRODUCTS FROM MTX
FEATURES
In-Wall Loudspeakers
MODEL 520W
5-1/4" Two-Way In-Wall Speaker 25mm Soft Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 84dB 50W RMS/100W Peak Music Frequency Response: 53Hz-20kHz 11"H x 7 1/2"W x 2 1/2"D
MODEL 825W
8" Two-Way InWall Speaker 25mm Soft Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 86dB 60W RMS/120W Peak Music Frequency Response: 36Hz-20kHz 14 1/16"H x 10 1/16"W x 3 1/2"D
Home Loudspeakers
MONITOR6
6-1/2” Two-Way Home Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 89dB 100W RMS/200W Peak Music Frequency Response: 55Hz-20kHz 12 3/4”H x 7 1/2”W x 8 1/2”D
MONITOR10
10” Three-Way Home Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 92dB 200W RMS/400W Peak Music Frequency Response: 30Hz-20kHz 31 7/16”H x 11 1/8”W x 14 5/16”D
MODEL 625W
6-1/2" Two-Way In-Wall Speaker 25mm Soft Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 85dB 55W RMS/110W Peak Music Frequency Response: 55Hz-20kHz 12 1/16"H x 8 9/16"W x 2 7/8"D
MONITOR6C
6-1/2” Center Channel Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 92dB 100W RMS/150W Peak Music Frequency Response: 60Hz-20kHz 7 1/2”H x 17 5/8”W x 8”D
MONITOR12
12” Three-Way Home Loudspeaker 19mm Dome Tweeter Impedance:8 ohms nominal Sensitivity: 94dB 250W RMS/500W Peak Music Frequency Response: 25Hz-20kHz 35”H x 13 1/8”W x 16 1/16”D
Both models utilize a unique dual voice coil woofer design that allows both channels of a stereo system to drive one cone. This feature coupled with a dual tweeter system allow this unit to operate as two speakers in one.
This unit is of a water resistant design and therefore can be used in high humidity areas such as a bathroom or laundry room.
TECHNICAL ASSISTANCE
For additional technical assistance you can visit our website at www.mtx.com. Otherwise, our technical service representatives can be reached by phone: 1-800­CALL-MTX or by email: technical@mtx.com.
STEP 1
Using a stud finder (available at low cost at most hardware stores) or other accu­rate method, locate center point between two joists and mark. Using template provided, trace hole pattern on surface of ceiling
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol­lowing traced pattern.
STEP 4
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings to rotate out behind the mounting surface and secure the speaker in place.
STEP 3
Run loudspeaker wires to sound source location. There are several methods you can use to accomplish wiring, depending on the construction characteristics of the room or house. You can add a professional touch to your installation by using a speaker terminal plate at the source location. Leave sufficient amount of wire at speaker location (8 to 10 inches) to complete connection.
STEP 6
After the speaker panel is secured tightly, test for sound. When you are satisfied the speaker is operational, affix grill. As grill is designed for a snug fit, you’ll need to position one edge into slot first, and press or squeeze around perimeter of grill, while pushing leading edges into grill slot.
Loading...