MTX Audio 512C User Manual

MODEL 512C/ MODEL 612C
1 Mitek Plaza
Winslow, IL 61089
815-367-3000 800-225-5689
and MODEL 812C OWNER'S MANUAL
21A6529
CONGRATULATIONS
SPECIFICATIONS MODEL 512C MODEL 612C MODEL 812C
Frequency Response 72Hz-20kHz 50Hz-20kHz 40Hz-20kHz
±3dB ±3dB ±3dB
Impedance 8 ohms nominal 8 ohms nominal 8 ohms nominal
Power Handling 30 Watts RMS 35 Watts RMS 45 Watts RMS
60 Watts Peak 70 Watts Peak 90 Watts Peak Music Music Music
Sensitivity (1W/1m) 85dB 85dB 85dB
Woofer Diameter 5-1/4” 6-1/2” 8”
Tweeter 1/2" 1/2" 1/2"
Balanced Dome Balanced Dome Balanced Dome
MTX WARRANTY INFORMATION
All MTX In-Ceiling Speakers purchased in the United States from an authorized MTX dealer are guaranteed against defects in material and workmanship for a period ten years from the date purchased by the end user, and limited to the original retail pur­chaser of the product.
MTX disclaims any liability for other incurred damages resulting from product defects. Any expenses incurred in the removal and reinstallation of product is not covered by this warranty. MTX's total liability will not exceed the purchase price of the product. This warranty is valid in the United States only.
Proof of purchase is required when requesting service, so please retain your sales receipt and take a moment to register your warranty on line at www.mtx.com.
Mounting Depth 3-5/16” 3-1/8” 3-3/4”
Baffle Diameter 7-3/4” 9” 10-3/4”
PAINTING YOUR MTX IN-CEILING SPEAKERS
OTHER PRODUCTS FROM MTX
LOUDSPEAKER PLACEMENT
In-Wall Loudspeakers
MODEL 625W
6-1/2” Two-Way In-Wall Speaker 25mm Soft Dome Swivel Tweeter Impedance: 8 ohms nominal Sensitivity: 85dB 55W RMS/110W Peak Music Frequency Response: 48Hz-20kHz 12”H x 8 5/8”W x 3 1/4”D
Home Loudspeakers
MONITOR6
6-1/2” Two-Way Home Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 89dB 100W RMS/200W Peak Music Frequency Response: 55Hz-20kHz 12 3/4”H x 7 1/2”W x 8 1/2”D
MONITOR10
10” Three-Way Home Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 92dB 200W RMS/400W Peak Music Frequency Response: 30Hz-20kHz 31 7/16”H x 11 1/8”W x 14 5/16”D
MODEL 825W
8” Two-Way In-Wall Speaker 25mm Soft Dome Swivel Tweeter Impedance: 8 ohms nominal Sensitivity: 86dB 60W RMS/120W Peak Music Frequency Response: 36Hz-20kHz 14”H x 10”W x 3-1/2”D
MONITOR6C
6-1/2” Center Channel Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 92dB 100W RMS/150W Peak Music Frequency Response: 60Hz-20kHz 7 1/2”H x 17 5/8”W x 8”D
MONITOR12
12” Three-Way Home Loudspeaker 19mm Dome Tweeter Impedance: 8 ohms nominal Sensitivity: 94dB 250W RMS/500W Peak Music Frequency Response: 25Hz-20kHz 35”H x 13 1/8”W x 16 1/16”D
TECHNICAL ASSISTANCE
For additional technical assistance you can visit our website at www.mtx.com. Otherwise, our technical service representatives can be reached by phone: 1-800­CALL-MTX or by email: technical@mtx.com.
STEP 1
Using a stud finder (available at low cost at most hardware stores) or other accu­rate method, locate center point between two joists and mark. Using template provided, trace hole pattern on surface of ceiling
STEP 4
Attach loudspeaker wires to speaker terminals, observing correct polarity, and position speaker frame up into cutout. Be careful not to pinch wires in the pro­cess.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, fol­lowing traced pattern.
STEP 3
Run loudspeaker wires to sound source location. There are several methods you can use to accomplish wiring, depending on the construction characteristics of the room or house. You can add a professional touch to your installation by using a speaker terminal plate at the source location. Leave sufficient amount of wire at speaker location (8 to 10 inches) to complete connection.
STEP 5
Carefully tighten the four mounting screws. This will cause the mounting wings to rotate out behind the mounting surface and secure the speaker in place.
STEP 6
Loading...