MTX Audio 502W User Manual [en, de, fr, es]

MODEL 502W / MODEL 602W

1 Mitek Plaza

Winslow, IL 61089

815-367-3000
800-225-5689

www.mtx.com

OWNER'S MANUAL

21A7594

CONGRATULATIONS

We appreciate your choice of MTX In-Wall Speakers. Properly installed and operated, MTX In-Wall
Loudspeakers should provide years of worry free listening pleasure. It’s important that you follow each
step in this guide carefully to insure proper installation.

SPECIFICATIONS MODEL 502W MODEL 602W

Frequency Response 53Hz-20kHz 43Hz-20kHz
+/- 3dB +/- 3dB

Power 45W RMS/ 50W RMS
Handling 90W Peak Music 100W Peak Music

Sensitivity (1W/1M) 84dB 85dB
Woofer Diameter 5-1/4" 6-1/2"
Tweeter 1/2" Polycarbonate 1/2" Polycarbonate

Balanced Dome Balanced Dome
Mounting Depth 2-3/8" (60.3mm) 2-7/8" (73.0mm)
Baffle Size 11"H x 7-1/2"W 12"H x 8-5/8"W

(279.4mm x 190.5mm) (304.8mm x 219.1mm)
Cutout Size 9-5/8"H x 6-3/16"W 10-3/4"H x 7-3/8"W

(244.5mm x 157.2mm) (273.1mm x 187.3mm)

PAINTING YOUR MTX IN-WALLS

MTX In-Wall Speakers are designed to accept all types of interior and exterior paints. Spray or roller
application should provide excellent results. A paint shield is included with all MTX In-Wall Speakers to
protect the speakers during the painting proce

ss.

LOUDSPEAKER PLACEMENT

MTX In-Wall Speakers are designed to work within any interior decorating scheme. They can be installed
in virtually any location where flush mounting is possible. To maximize their sound performance however
certain guidelines should be followed. For the best stereo reproduction the two loudspeakers should be
placed an equal distance from your listening position and separated so that the angle between them, at
the listening position, is between 40 and 60 degrees.

For best stereo imaging, we recommend that the units be placed so that the tweeters are as close as
possible to the ear level of a seated listener.

MTX WARRANTY INFORMATION

All MTX In-Wall Speakers purchased in the United States from an authorized MTX
dealer are guaranteed against defects in material and workmanship for a period ten years from
the date purchased by the end user, and limited to the original retail purchaser of the product.
Product found to be defective during that period will be repaired or replaced by MTX at no
charge. This warranty is void if it is determined that unauthorized parties have attempted repairs
or alterations of any nature. Warranty does not extend to cosmetics or finish. Before presuming
a defect is present in the product, be certain that all related equipment and wiring is functioning
properly. MTX disclaims any liability for other incurred damages resulting from product defects.
Any expenses incurred in the removal and reinstallation of product is not covered by this war
ranty. MTX's total liability will not exceed the purchase price of the product. If a defect is present,
your authorized MTX dealer may be able to effect repairs.

Proof of purchase is required when requesting service, so please retain your sales
receipt and take a moment to register your product on line at www.mtx.com.

STEP 1

Using a stud finder (available at low cost at most hardware stores) or other accurate method, locate
center point between two studs and mark. Using template provided, trace hole pattern on surface of
wall. Placing a bubble level on either the horizontal or vertical guidelines of template will assist you in
leveling the hole p

attern.

-

STEP 2

Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall, following traced pattern.

STEP 3

Run loudspeaker wires to sound source location. There are several methods you can use to accomplish
wiring, depending on the construction characteristics of the room or house. You can add a professional
touch to your installation by using a speaker terminal plate at the source location. Leave sufficient amount
of wire at speaker location (8 to 10 inches) to complete connection.