Page 1
MTX.COM
OWNER’S MANUAL
MUDRNGRDK
POLARIS® RANGER® DASH KIT
[FOR USE WITH MTX AWMC3 HEAD UNIT]
Page 2
MTX.COM
2
IMPORTANT NOTICE
If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support
at 1-800-225-5689.
When connecting power and ground wires ensure that the red power wire is fused at the point
where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a
short circuit develops between the vehicle connection point and the product.
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• Dash Kit
• Allen Wrench
• (2) Shoulder Head Bolts
• (2) Speed Clips
• (4) Mounting Nuts
INSTALLATION TOOLS
The following is a list of suggested tools needed for installation:
• Torx - T40
• 5.5mm Nut Driver or Socket Wrench
• Pry Tool or Small Flat Blade
INTRODUCTION
Thank you for purchasing this Polaris® RANGER® Dash Kit designed for the MTX Audio AWMC3
Bluetooth all-weather head unit. This easy to install dash kit is the perfect OEM t solution for your
Polaris® RANGER®. Congratulations and enjoy the ultimate audio experience with MTX!
FITS THE FOLLOWING VEHICLES
• RANGER® 570 Full-Size (2014 and up)
• RANGER XP® 900 (2014 and up)
• RANGER XP® 1000 EPS (2014 and up)
• RANGER® Diesel (2014 and up)
• RANGER CREW® 570-4 / 570-6 (2014 and up)
• RANGER CREW® XP 900 / XP1000 (2014 and up)
• RANGER CREW® Diesel (2014 and up)
Will not t 2018 Northstar Fullsize, Northstar Crew, or High Lifter Edition.
Will work with Polaris heater accessory installed.
Page 3
MTX.COM
3
SPECIFICATIONS
Page 4
MTX.COM
4
INSTALLATION
Step 1 - Remove the two (2) T40 screws found in the top dash cover.
Step 2 - Remove the two (2) trim panel pin rivets found on either side of the dash cover.
Step 3 - Lift and pull back the top dash cover to release the clips holding it in place.
Page 5
MTX.COM
5
Step 4 - Remove the two (2) T20 screws found at the bottom of the center dash panel and remove.
Note: Disconnect any switches making sure not to damage the vehicle or switch wiring. Make note to
remember what connector is associated with each specic switch.
Step 5 - Prepare the new dash kit by aligning the radio with the four (4) pre-installed threaded posts.
Page 6
MTX.COM
6
Step 6 - With the radio seated in place, install four (4) included retaining nuts using a 5.5mm socket or
nut driver
Note: This dash kit also offers space to mount additional rocker panel switches for accessories. On
the rear of the dash kit, grooves are provided to give you proper location and size for mounting.
Step 7 - Reconnect any switches or wiring harnesses and insert the radio and dash kit assembly into
the dash opening.
Page 7
MTX.COM
7
Step 8 - Mount the dash kit using the two (2) T-20 screws removed earlier.
Note: You would now make any power, ground, and speaker connections using the supplied radio
harness
Step 9 - Reinstall the top dash panel and reattach using the hardware removed earlier.
Page 8
MTX.COM
8
© 2017 Mitek Corporation. All rights reserved. MTX, Mud Nation, and Let’s Do Something Dirty are trademarks
of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in
the U.S.A.
Due to continual product development, all specifications are subject to change without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689
MTX005688 RevA 12/17 • 21A10623 • AW0015505
Loading...