MTX CD520C, CD520W, CD620C, CD620W, CD622C User Manual

21A8792

1 Mitek Plaza

Winslow, IL 61089

815-367-3000
800-225-5689

www.mtx.com

Warranty Information..

MTX products purchased in the United States from an authorized MTX dealer, is guaranteed against de­fects in material and workmanship for a period of TEN YEARS from the date purchased by the end user,
and limited to the original retail purchaser of the product. Product found to be defective during that period
will be repaired or replaced by MTX at no charge. This warranty is void if it is determined that unauthorized
parties have attempted repairs or alterations of any nature. Warranty does not extend to cosmetics or fin

­ish. Before presuming a defect is present in the product, be certain tht all related equipment and wiring is
functioning properly. MTX disclaims any liabilty for other incurred damages resulting from product defects.
Any expenses incurred in the removal and reinstallation of product is not covered by this warranty. MTX’s
total liability will not exceed the purchase price of the product. If a defect is present, your authorized MTX
dealer may be able effect repairs.

Proof of purchase is required when requesting service, so please retain your sales receipt and take a mo

­ment to register your product on line at

mtx.com. Also, a Return Authorization number (RA) is required

before shipping product back to MTX, call 800-556-2888 or 608-328-5560.

MTX Contractor Distributed Series

In-Walls and In-Ceilings

Congratulations..

We appreciate your choice of MTX Contractor Distributed Series In-Wall and In-Ceiling speakers. Prop­erly installed and operated, they should provide years of worry-free listening pleasure. It’s important that
you follow each step in the mounting directions on the mounting template and the recommendations in this
guide carefully to insure proper installation.

Features..

• 12dB/octave highpass crossover

• 6dB/octave lowpass crossover

• Laminated steel core inductors prevent distortion

• Neodymium tweeter magnet material

• Silk dome tweeter material

• Polypropylene woofer cone material with rubber surround

• Debris resistant woofer basket

• Aimable swivel tweeter (except CD622C and CD822C)

• Aluminum grille

• Air core highpass inductors

• Input binding posts accept up to 8 gauge wire

Painting Your Loudspeakers..

MTX Contractor Distributed Series In-Wall and In-Ceiling speakers are designed to accept all types of
interior and exterior paints. Spray or roller application should provide excellent results. A paint shield is
included with all MTX speakers to protect the drivers during the painting process. The cloth inserts in the
grilles should be removed before the speakers are painted. They should be placed back in the grilles after
the paint is dry.

Loudspeaker Placement..

MTX Contractor Distributed Series In-Wall and In-Ceiling speakers are designed to work within any inte­rior decorating scheme. They can be installed in virtually any location where flush mounting is possible.
To maximize their acoustical performance, however, certain guidelines should be followed. For the best
stereo reproduction the two loudspeakers should be placed an equal distance from your listening position
and separated so that the angle between them, at the listening position, is between 40 and 60 degrees.
See Figure 1 and Figure 2.

Figure 1 Figure 2

Considérations d’épaisseur du mur et du plafond

Épaisseur maximale du matériau

Tous les modèles MTX Contractor Distributed d’enceintes encastrables au plafond et au mur mention

­nés dans ce livret peuvent être installés au plafond ou au mur sur une épaisseur maximale de 25 mm à
l’aide des ailettes de montage installées dans la position normale de sortie d’usine. Si l’épaisseur du mur
ou du plafond est supérieure à 25 mm, les ailettes doivent être retournées dans les rails pour permettre
leur utilisation avec un matériau épais. En retournant les ailettes, on permet l’installation de l’enceinte
au mur ou au plafond sur une épaisseur pouvant atteindre 38 mm. Pour retourner les ailettes, dévisser
complètement les vis de montage pour les sortir des ailettes. Puis, faire soigneusement sortir les ailettes
des rails en les soulevant à l’aide d’un levier. Retourner les ailettes, les remettre en place dans les rails
et réinstaller les vis de montage.

Épaisseur minimale du matériau

Les modèles suivants peuvent être installés au mur et au plafond sur des matériaux d’épaisseur quasi

­ment nulle : CD520W et CD620W.

Les modèles suivants peuvent être installés au mur et au plafond sur des matériaux d’au moins 3 mm
d’épaisseur : CD520C, CD620C, CD622C, CD820C et CD822C.