MTD PS720 User Manual

Operator’s Manual

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Maintenance & Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . .5

Replacing Saw Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Chain Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

All information, illustrations, and specifications in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice.

SAVE THESE INSTRUCTIONS

For service call

1-800-345-8746

, or 1-800-668-1238 in Canada to

obtain a list of authorized service dealers near you. For more details about your unit, visit our website at www.mtdproducts.com.

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, please call the Customer Support Department.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S. PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer.

Copy the serial number here:

Copy the model and parent part number here:

Before beginning, locate the unit’s model plate. It lists the model and serial numbers of your unit. Refer to the sample plate below and copy the information for future reference.

PART NO. 769-03486 (10/07)

In an effort to reduce the impact on the forests, and reduce carbon and greenhouse gas emissions, MTD is using less paper by reducing the text size of this manual.

Pole Saw

PS720

• Use only genuine factory replacement parts and accessories for this unit. These are available from your authorized service dealer. Use of any unauthorized parts or accessories could lead to serious injury to the user or damage to the unit, and void your warranty.

KICKBACK SAFETY PRECAUTIONS

• With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents.

• Grip trimmer firmly. Hold the pole saw/ trimmer unit firmly with both hands when the motor is running. Keep one hand on the grip and the other hand on the handle.

• Do not let the nose of the guide bar contact a log, branch, ground or other obstruction.

• Always cut with the engine running at full speed. Fully squeeze the throttle trigger and maintain a steady cutting speed.

• Do not over reach.

• Follow the manufacturer’s sharpening and maintenance instructions for the saw chain.

• Use only replacement bars and chains specified by the manufacturer or the equivalent.

OTHER SAFETY PRECAUTIONS

• DO NOT operate a pole saw with one hand! Serious injury to the operator, helpers, or bystanders may result from one-handed operation. A pole saw is intended for two-handed use.

• Do not operate a pole saw if you are fatigued.

• Do not wear loose clothing or jewelry, as they can get caught in moving parts. Non-skid footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.

• Use safety glasses, safety footwear, snug fitting clothing, protective gloves, and protective hearing and head gear.

• Keep the work area clean. Cluttered areas invite injuries. Do not start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling branches.

• Stay Alert. Watch what you are doing. Use common sense. Do not operate the pole saw when you are tired. Keep all parts of your body away from the saw chain when the motor is operating. Before you start the saw, make sure the saw chain is not contacting anything.

•

Disconnect the pole saw when not in use, before servicing, and when changing accessories and attachments such as saw chain and guard.

•

Check damaged parts. Before further use of the pole saw, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center, unless otherwise indicated in this instruction manual.

• Use extreme caution when cutting small sized brush and sapling, as slender material may catch the saw chain and be whipped toward you or pull you off balance.

• Do not operate a pole saw in a tree unless you are specifically trained to do so. When cutting a limb that is under tension, be alert for spring back so that you will not be struck when the tension in the wood fibers is released.

• Do not expose the pole saw to rain. Do not use the pole saw in damp or wet locations.

•

Do not use the pole saw in the presence of flammable liquids or gases.

READ ALL INSTRUCTIONS BEFORE OPERATING

• Carefully read and understand the operator's manual of the unit that powers this attachment.

• Read this operating instruction manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

• Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.

• Never allow children to operate the equipment. Never allow adults unfamiliar with the instructions to use the unit. Never allow adults to operate the equipment without proper instruction.

• All guards and safety attachments must be installed properly before operating the unit.

POLE SAW OPERATING PROCEDURES

•

Keep bystanders, especially children and pets, at least 50 ft (15 m) away.

• Wear safety glasses or goggles that are marked as meeting ANSI Z87.1-1989 standards, and ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty.

• Wear heavy, long pants, boots, gloves and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.

• Use the unit only in daylight or good artificial light.

• Use the right tool. Only use this tool for the purpose intended.

• Always stop the engine/motor when operation is delayed or when walking from one location to another.

RULES FOR SAFE OPERATION

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA

SYMBOL MEANING

WARNING:

Failure to obey a safety warning can result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION:

Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

• IMPORTANT SAFETY INSTRUCTIONS •

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

SAFETY ALERT:

Indicates danger, warning or caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.

NOTE: Advises you of information or instructions vital to the

operation or maintenance of the equipment.

DANGER:

Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING:

When using the unit, you must follow the safety rules. Please read these instructions before operating the unit in order to ensure the safety of the operator and any bystanders. Please keep these instructions for later use.

WARNING:

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse action, kicking the guide bar rapidly back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw, which could result in serious injury to the user. Do not rely exclusively upon the safety devices built into your saw. As a pole saw user, you should take several steps to keep your cutting jobs free from accident or injury.

RULES FOR SAFE OPERATION

•

All pole saw service, other than the items listed in the user manual safety and maintenance instructions, should be performed by competent pole saw personnel. Do not attempt to repair it yourself; there are no user serviceable parts inside.

• The pole saw will do a better and safer job when used at the rate for which it was intended.

•

Use the right tool. Cut wood only. Do not use the pole saw for purposes for which it was not intended. For example, do not use the pole saw for cutting plastic, masonry, or non-building materials.

•

Use devices, such as low-kickback chain, guide bar nose guards, chain brakes and special guide bars, which reduce the risks associated with kickback.

• There are no other replacement components for achieving kickback protection in accordance with CSA Z62.3.

• Do not operate a pole saw that is damaged, improperly adjusted, or not completely and securely assembled. Be sure that the saw chain stops moving when the trigger is released.

• Do not attempt operations beyond your capacity or experience.

• Never remove, modify or make inoperative any safety device furnished with your unit.

•

This saw is classified by CSA as a Class 2C saw. It is intended for infrequent use by homeowner’s, cottagers and campers, and for such general applications such as clearing, pruning, cutting firewood, etc. It is not intended for prolonged use. If the intended use involves prolonged periods of operation, this may cause circulatory problems in the user’s hands due to vibration. It may be appropriate to use a saw having an anti-vibration feature.

• Safety clothing required by your safety organizations, government regulations, or your employer should be used; otherwise, snug fitting clothing, safety footwear, and hand and ear protection should be worn.

• Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.1-1991 and is in accordance with CSA Z62.3. Do not use other replacement chain unless it has met these requirements for your specific model.

•

Do not use any other cutting attachment or accessories. Use only original equipment manufacturer replacement parts and accessories, which are designed specifically to enhance the performance and maximize the safe operation of our products. Failure to do so may cause poor performance and possible injury. Use only the chain and bar supplied with this product. Do not use any other cutting attachment. Use of such attachments will void your factory warranty and could result in serious bodily injury.

• Never touch the chain or attempt to service the saw while the engine is running. Make sure all moving parts have stopped. Allow the chain to cool, as the chain can be hot.

• Check the bar and chain at frequent intervals for proper adjustment. Make sure the bar and chain are properly tightened and sharpened. Visually inspect for damage. Repair any damage before restarting or operating the pole saw.

• Do not cut near electrical cables or power lines.

• Do not use the pole saw to fell a tree. Use a standard chain saw for this application.

MAINTENANCE AND STORAGE

• Allow the unit to cool before storing or transporting. Be sure to secure the unit while transporting.

• Always use the transport guard on the bar and chain during transportation and storage.

• Store the unit in a locked up and dry or high and dry place to prevent unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after each use.

• Keep these instructions. Refer to them often and use them to instruct other users. If you loan someone this unit, also loan them these instructions.

• Only qualified personnel should perform any repairs or maintenance procedures that are not described in this manual.

SAVE THESE INSTRUCTIONS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in conjunction with other symbols or pictographs.

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders.

• WEAR HEAD, EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye protection meeting ANSI Z87.1-1989 standards and ear protection when operating this unit. Falling objects can cause severe head injury. Wear head protection when operating this unit.Use a full face shield when needed.

SYMBOL MEANING

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially children

and pets, at least 50 feet (15 m) from the operating area.

• POWER LINES CAN CAUSE SEVERE INJURY

WARNING: Do not operate unit near power lines.

Contact with a power line may cause serious injury or damage to the unit. Maintain a clearance of at least 50 ft (15 m) between the pole saw (including any branches it is contacting) and any electrical line.

SYMBOL MEANING

• USE BOTH HANDS

Always use both hands while operating the chain saw. Never use only one hand to operate the saw.

• GUIDE BAR WARNING

Contact of the guide bar tip with any object should be avoided. Tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious injury.

• HOT SURFACE WARNING

Do not touch a hot surface. You may get burned. These parts get extremely hot from operation. They remain hot for a short time after the unit is turned off.

• CHAIN OIL ADJUSTMENT INDICATOR

The chain must be continously coated with oil to function properly. Make sure to set the Oil Adjustment Screw to allow a sufficient amount of oil to flow continuously onto the chain.

Use a 3/32-inch Allen wrench to adjust the Oil Adjustment Screw.

Installing the Add-On or Extension Boom

1. Remove the hanger or shipping cap from the top of the shaft housing.

2. Turn knob counterclockwise to loosen (Fig.

3).

3. While firmly holding the add-on or extension boom, push it straight into the coupler (Fig. 2).

NOTE: Aligning the release button with the guide recess will

help installation (Fig. 1).

4. Turn the knob clockwise to tighten (Fig. 3).

5. Repeat steps 1–4 for the add-on or extension boom.

The add-on should be installed with the release button in the primary hole.

Check Flex Shaft Engagement Prior to Using

1. Start the unit.

2. Briefly engage and release the trigger.

3. Check that add-on is operating.

4. If the add-on is not operating, remove add-on and repeat steps for installing the add-on.

5. Recheck operation of add-on attachment.

Guide Bar

Saw Chain

Drive Shaft

Guide Bar

Nose

Chain Guard

Hook

Bar Retaining

Nuts

KNOW YOUR UNIT

Extension Boom

Tension Adjustment

Screw

Oil Adjustment

Screw

Oil Reservoir

Chain Transport

Guard

Hanger

Coupler

Oil Tank

Cap

Shipping Cap

ASSEMBLY INSTRUCTIONS

FILLING THE OIL RESERVOIR

Follow the following steps to fill the oil reservoir:

1. Place the unit on a flat surface.

2. Remove the Oil Tank Cap.

3. Open the oil bottle provided with your unit.

4. Pour oil into the reservoir until filled.

NOTE: The oil reservoir may be filled to the lip of the fill opening without damaging the unit.

ASSEMBLING THE COUPLER

The Trimmer Plus add-on may be mounted to different power tools. The instruction manuals for the basic power tool and the attachment contain the information necessary for operation of the power tool combination. Therefore, aways read BOTH instruction manuals before using the power tool for the first time. Keep the manuals in a safe place for future reference.

NOTE: To make installing or removing the add-on easier,

place the unit on the ground or on a work bench.

Removing the Add-On or Extension Boom

1. Turn the knob counterclockwise to loosen (Fig. 3).

2. Press and hold the release button (Fig. 1).

3. While firmly holding the upper shaft housing, pull the addon or extension boom out of the coupler (Fig. 2).

OPERATING INSTRUCTIONS

OPERATING PRECAUTIONS

1. Keep bystanders 50 feet (15 meters) away when operating the saw.

2. Do not use the pole saw to cut down trees. Use a chain saw without a pole attachment.

3. Make sure the oil tank is full and oil is lubricating the chain prior to starting.

4. Grip pole saw/ trimmer securely—one hand on the grip, the other on the handle.

5. Keep finger off the trigger until ready to make cut.

6. Before starting the pole saw, make sure the chain is not touching anything.

7. Keep all parts of your body away from the chain when the saw is running.

8. Do not force the chain saw while cutting. Apply light pressure. It will do the job better and safer at the rate for which it was intended.

9. When cutting limbs or branches that are under tension, use extreme caution. Be alert for wood springing back. When wood tension is released, the limb could spring back and strike operator causing severe injury or death.

10. When carrying pole saw from one place to another:

• hold pole at balance point

• keep guide bar and chain to the rear

11. Do not cut small brush and saplings with the pole saw. Slender matter may catch in the chain and be whipped toward you. This could also pull you off balance.

12. Never stand directly under the limb you are trimming. Always position yourself out of the path of falling debris (Fig. 4).

13. Never stand on a ladder or other type of unstable support while using the pole saw.

14. Always use both hands to operate pole saw. Keep a firm, steady pressure on the pole saw while cutting, but do not try to force the saw through the wood.

15. Keep other persons away from cutting end of pole saw and at a safe distance from work area. (Fig. 5).

16. Do not use the pole saw near cable, electric power or telephone lines. Maintain a minimum clearance of 50 feet (15 m) from all power lines (Fig. 6).

STARTING INSTRUCTIONS

Start and operate your pole saw without assistance. For specific starting instructions, see the appropriate section of your powerhead manual. Proper starting methods reduce the risk of injury.

1. Place the pole saw on firm ground or other solid surface in an open area.

2. Maintain good balance and secure footing.

OPERATING TIPS

Fig. 4

DANGER:

Failure to fill the oil reservoir will cause irreparable damage to the unit.

Make sure the oil reservoir is always filled.

WARNING:

Prior to operation, read and understand the operator’s manual for unit to be used with this add-on.

WARNING:

To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing add-ons.

CAUTION:

Lock the release button in the primary hole and securely tighten the knob

before operating this unit.

WARNING:

To avoid serious personal injury and damage to the unit, NEVER install more than one extension boom to a power tool.

Guide Recess

Fig. 1

Release

Button

Rapid-Link™Coupler

Upper Shaft

Housing

Fig. 2

Lower Shaft

Housing

Primary Hole

Knob

Fig. 3

90˚ Edging Hole

(Trimmer Only)

WARNING:

Oil constantly flows from the oil reservoir to oil the chain. Check the oil

level constantly so that the oil level does not drop below half full.

WARNING:

Dress properly to reduce the risk of injury when operating this unit. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy long pants, boots and gloves. Wear a hard hat. Use a full face shield when needed.

Fig. 5

Fig. 6

WARNING:

To reduce the risk of fire and burn injuries, start the engine at least 30 ft. (9.1 m) from the fueling spot, outdoors only.

ASSEMBLY INSTRUCTIONS

CAUTION:

Add-ons are to be used in the primary hole only. Using the wrong hole

could lead to personal injury or damage to the unit.

WARNING:

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse action, kicking the guide bar rapidly back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw, which could result in serious injury to the user. Do not rely exclusively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury.

WARNING:

Do not use the pole saw to cut limbs larger than 4” (10 cm) in diameter.

GUIDE BAR MAINTENANCE

NOTE: Proper maintenance of the guide bar is essential to the performance of your pole saw.

Proper guide bar maintenance will keep your saw in good working order.

Most guide bar problems can be prevented merely by keeping the chain saw well maintained. Incorrect filing and non-uniform cutter and depth gauge settings cause most guide bar problems, primarily resulting in uneven bar wear. As the bar wears unevenly, the rails widen, which may cause chain clatter and difficulty in making straight cuts. Insufficient guide bar lubrication and operating the saw with a chain that is too tight will contribute to rapid bar wear. Refer to Saw Chain Tension Adjustment and Oiling the Chain. To help minimize bar wear, the following guide bar maintenance is recommended:

Bar Wear

Turn guide bar frequently at regular intervals (for example, after 5 hours of use), to ensure even wear on top and bottom of bar.

Bar Grooves

Bar grooves (or rails which support and carry the chain) should be cleaned if the saw has been heavily used or if the saw chain appears dirty. Rails should always be cleaned every time the saw chain is removed.

To clean guide bar rails:

1. Remove chain guard, bar, and chain. Refer to Saw Chain Replacement / Installation.

2. Using a screwdriver, putty knife, wire brush or other similar instrument, clear residue from the rails on the guide bar (Fig. 13).

This will keep the oil passages open to provide proper lubrication to the bar and chain.

3. Ensure the sprocket in the bar turns freely during cleaning.

4. Reinstall the bar, chain, chainguard, screw, and bar retaining nuts. Refer to Saw Chain Replacement / Installation.

Oil Passages

Oil passages at the bar pad should be cleaned to ensure proper lubrication of the bar and chain during operation. This can be done using a soft wire small enough to insert into the oil discharge hole.

CHAIN MAINTENANCE

Always use a replacement saw chain designed as “low-kickback” or a saw chain which meets the lowkickback performance. A standard saw chain (a chain which does not have the kickback reducing guard links) should only be used by an experienced professional chain saw operator.

Low-Kickback Saw Chain

A low-kickback saw chain is a chain which has met the kickback performance requirements of ANSI B175.1. Do not use other replacement chain unless it has met these requirements for your specific model. By keeping the saw chain in good working condition and correctly serviced as recommended in this manual, you will be able to maintain the safety system of your polesaw over the life of the product.

Chain Tension

Check the chain tension frequently and adjust as often as necessary to keep the chain snug on the bar, but loose enough to be pulled around by hand. Refer to Saw Chain Tension Adjustment.

Breaking in a New Saw Chain

A new chain and bar will need readjustment after as few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will begin to lengthen quickly. Over a period of time, however, the moving parts of the saw chain will become worn, resulting in what is called chain stretch. This is normal. When it is no longer possible to obtain correct chain tension adjustment, a link will have to be removed to shorten the chain. See your MTD Authorized Service Center to have this repair performed.

CLEANING AND STORAGE

• Slacken the chain if you have retensioned it at operating temperature during cutting work.

• The chain contracts as it cools down. If it is not slackened, it may damage the gearbox and bearings.

Storing the Machine for a Short Period

Wait for the engine to cool down. Drain the fuel tank and store the machine in a dry place well away from sources of ignition until you need it again.

• Attach the transport guard to the bar/chain before storing the unit.

• Store the unit in a dry, high and/or locked location, out of the reach of children and other unauthorized

persons.

Long-Term Storage

• Remove the saw chain and guide bar, clean them, and spray them with corrosion inhibiting oil.

• Attach the transport guard to the bar/chain before storing.

OPERATING INSTRUCTIONS

• Avoid kickback. Kickback can result in severe injury or death.

• Do not operate the pole saw while in a tree, on a ladder or any other unstable work surface, or in any awkward position. You may lose control of the pole saw causing severe injury.

• Do not extend your arms above shoulders when using the pole saw.

• Seek professional help if you are facing conditions beyond your ability.

• Trimming a tree is the process of cutting limbs from a living tree. Make sure your footing is firm. Keep your feet apart. Divide your weight evenly on both feet.

• Before starting unit, always check the chain lubrication and oil tank level.

NOTE: The chain must be continously coated with oil to function properly. Make sure that the oil

adjustment screw is set appropriately.

To trim a limb (pruning):

1. Make the first cut six inches from tree trunk on the

underside of the limb. Use the top of the guide bar to make this cut. Cut a third of the way through the diameter of the limb (Fig. 7).

2. Move two to four inches farther out on the limb. Make the

second cut from above the limb. Continue the cut until you cut the limb off.

3. Make the third cut as close to the tree trunk as possible on

underside of limb stub. Use the top of the guide bar to make this cut. Cut a third through the diameter of stub.

4. Make the fourth cut directly above the third cut. Cut down

to meet the third cut. This will remove the limb stub.

WARNING:

If the oil tank runs out, the oil ajustment screw hole becomes clogged, or the chain fails to get proper lubrication in any fashion, the chain will overheat and cause irreversible damage to the unit and may result in severe injury. Excessive heat from friction can lead the chain to catastrophically fail and come off the bar while operating.

Cut 1

Fig. 7

Cut 2

Cut 4

Cut 3

MAINTENANCE AND REPAIR INSTRUCTIONS

SAW CHAIN REPLACEMENT/INSTALLATION

1. Remove the bar retaining nuts and screw. Then take off the chain guard (Fig. 8, B).

2. Using a flat-head screwdriver turn tension adjustment screw counterclockwise (Fig. 8, A) 4 turns.

3. Take off the chain and bar.

4. Prepare new chain and/or bar, and fit the chain into the groove in the bar.

5. Loop the saw chain over the drive sprocket with the cutting edges of the chain pointing in the direction of rotation (Fig. 9).

6. Adjust the tension adjustment screw (Fig. 8, A) to allow insertion of the bar (Fig. 10). Make sure the chain follows the slot in the guide bar and adjust the tension adjustment screw to make the chain fit snugly on the underside of the bar.

7. Install the chain guard and tighten bar retaining nuts and screw (Fig. 8, B).

SAW CHAIN TENSION ADJUSTMENT

Proper tension of the saw chain is extremely important and must be checked before starting, as well as during, any cutting operation. Taking the time to make needed adjustments to the saw chain will result in improved cutting performance and prolonged chain life.

NOTE: A new chain and bar will need readjustment after as

few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will lengthen quickly (Fig. 11).

To adjust the saw chain tension:

1. Loosen the bar retaining nuts so they are hand tight (Fig. 8, B).

2. Holding the nose of the bar up, use the screwdriver to turn the guide bar adjustment screw clockwise to tighten the chain (Fig. 8, A). Turning the screw counterclockwise loosens the chain on the guide bar.

3. While wearing heavy duty work gloves (after you’ve made the adjustment), move the saw chain back and forth on the guide bar to be sure the chain moves freely and is in proper mesh with the sprocket. Never move the chain with your bare hands.

NOTE: If the chain is difficult to rotate or if it binds on the guide bar, there is too much tension

applied and it must be adjusted. To decrease tension, turn the adjustment screw counterclockwise, slowly. Move the chain back and forth until it moves freely.

4. Holding the nose in upper position, securely tighten the bar retaining nuts.

CHAIN LUBRICATION

The pole saw chain is self-lubricating. Oil is dispersed onto the chain as the unit is used. Keep an adequate amount of oil in the oil tank. Use the bar-chain oil provided in the hardware pack. Always use bar-chain and sprocket oil or similar chain saw oil.

Setting the Oil Adjustment Screw

The Oil Adjustment Screw is located on top of the gearbox assembly (Fig. 12).

1. Insert a 3/32-inch Allen wrench into the oil adjustment screw.

Turn the screw counterclockwise to increase oil flow to the chain.

3. Turn the screw clockwise to restrict the oil flow to the chain.

WARNING:

Whenever handling the saw chain, always wear work gloves for protection

against sharp cutting edges.

Fig. 8

Bar Retaining

Nuts

Tension

Adjustment

Screw

Fig. 9

Fig. 10

Slot

Fig. 11

CAUTION:

If a chain is too loose or too tight, the bar chain and saw bearings will wear more rapidly. Refer to Figure 11 for information concerning correct cold tension (A), correct warm tension (B), and a chain in need of adjustment (C).

Oil

Adjustment

Screw

Fig. 12

Gearbox

Assembly

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING:

Ensure that the unit is off and the spark plug is disconnected (gas powerheads) before performing any maintenance on your saw.

Fig. 13

WARNING:

Unless you have experience and specialized training for dealing with kickback (see Important Safety Instructions), always use a low-kickback saw chain, which significantly reduces the danger of kickback. Low-kickback saw chain does not completely eliminate kickback. A lowkickback or “safety chain,” should never be regarded as total protection against injury.

WARNING:

Never remove, modify or make inoperative any safety device furnished with your unit. The low-kickback saw chain is a major safety feature provided for your protection.

WARNING:

Ensure that the unit is off and the spark plug is disconnected (for gas

powerheads) when working on the saw chain. Wear heavy duty gloves too.

WARNING:

Never use a loop of chain that has more than 3 links removed from it. This could damage the sprocket.

POLE SAW ADD-ON

Approximate Operating Weight of Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 lbs. (1.5 kg)

Drive Shaft Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 inches (66 cm)

Cutting Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 inches (20.3 cm)

SPECIFICATIONS

6in (15.2cm)

2-4in (5.1-10.2 cm)

Screw

Chain Guard

MANUEL DE L'UTILISATEUR

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Familiarisez-vous avec votre appareil . . . . . . . . . . . . . . . . . . . . . . .9

Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Mode d’emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Entretien et réparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Chainion replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Huiler la chaine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Toutes les informations, illustrations et spécifications contenues dans ce manuel tiennent compte des dernières informations techniques disponibles au moment de mettre sous presse. Nous nous réservons le droit d'y apporter des modifications à tout moment, sans préavis.

CONSERVER CES INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-800-3458746 aux États-Unis ou le 1-800-668-1238 au Canada.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ QUI VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS GARANTIE NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

Tout entretien effectué sur cet appareil pendant et après la période de garantie doit être fait par un concess- ionnaire agréé uniquement.

Copiez le numéro de série ici :

Copiez le numéro de modèle / pièce mère ici :

Avant d'assembler votre nouvel équipement, repérez la plaque signalétique de l'appareil et copiez ses informations dans l'espace ci-dessous. Ces informations sont essentielles si vous désirez obtenir de l'aide auprès de notre service technique ou d'un distributeur agréé. Un exemple de plaque signalétique est présenté ci-dessous.

PART NO. 769-03486 (10/07)

Dans un effort de réduire l’impact sur les forets et réduire les émissions de gaz carbonique ainsi que les émissions de gaz à effet de serre, MTD utilise moins de papier en réduisant la taille du texte de ce manuel.

Tronçonneuse sur Perche

PS720

+ 14 hidden pages