MTD PS User Manual
Operator’s Manual
Electric Pole Saw
Model
MTD PS
English
IMPORTANT: READ SAFETY RULES
AND INSTRUCTIONS CAREFULLY
P/N 6096-210805 © 2005/11
PRINTED IN TAIWAN
TABLE OF CONTENTS
Warranty Statement Page 1
Rules For Safe Operation Pages 2 - 6
Important Safety Instructions Pages 7 - 9
Assembly Instructions Pages 10 -12
Operating Instructions Pages 13 -14
General Cutting Instructions Pages 15 - 17
Maintenance Instructions Pages 18 - 19
Parts List Page 20
Manufacturer’s Limited Warranty Page 21
WARRANTY STATEMENT
TWO YEARS LIMITED WARRANTY ON YARD MACHINES POLE SAW
For two years from the date of purchase, when this pole saw is used and maintained according to the
operator’s manual, Yard Machines will repair any defect in material for workmanship free of charge.
If this pole saw is used for commercial or rental purposes, this warranty applies for only 90 days from
the date of purchase.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THIS POLE SAW TO THE NEAREST MTD
REPAIR DEALER.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your atten
tion to possible dangers. The safety symbols, and their
explanations, deserve your careful attention and understanding. The safety war
eliminate any danger. The instructions or warnings they
give are not substitutes for proper accident prevention
measures.
nings do not by themselves
-
SYMBOL MEANING
Indicates
SAFETY ALERT:
tion. Attention is required in order to avoid
serious personal injury. May be used in
conjunction with other symbols or pictographs.
NOTE: Advises you of information or instructions vital to
the operation or maintenance of the equipment.
Read the Operator’s Manual(s) and follow all warnings
and safety instructions.
Failure to do so can result in serious injury to the
operator and/or bystanders.
danger, warning or cau-
SYMBOL MEANING
DANGER:
serious injury to yourself or to others.
Always follow the safety precautions to
reduce the risk of fire, electric shock and
personal injury.
WARNING:
injury to yourself and others. Always follow
the safety precautions to reduce the risk of
fire, electric shock and personal injury.
CAUTION:
property damage or personal injury to yourself or to others. Always follow the safety
precautions to reduce the risk of fire, electric shock and personal injury.
e to obey a safety
Failur
warning will result in
Failure to obey a safety
warning can result in
Failure to obey a safety
warning may result in
• IMPORTANT SAFETY INSTRUCTIONS •
READ ALL INSTRUCTIONS
BEFORE OPERATING
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
When using the unit,
WARNING:
read these instructions before operating the
unit in order to ensure the safety of the
operator and any bystanders. Please keep
these instructions for later use.
• Do not operate this unit when tired, ill or under the
influence of alcohol, drugs or medication.
• Children must not operate the unit. Teens must be
accompanied and guided by an adult.
• All guards and safety attachments must be installed
properly before operating the unit.
• Inspect the unit before use. Replace damaged parts.
Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped or damaged in
any way. Do not operate the unit with loose or damaged parts.
safety rules. Please
• Carefully inspect the area before starting the unit.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
• Clear the area of children, bystanders, and pets. At a
minimum, keep all children, bystanders, and pets outside a 50 feet (15m.) radius; there still may be a risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are
approached, stop the unit immediately.
21
RULES FOR SAFE OPERATION
Max. CKA 45˚
• Do not operate a chain saw that is damaged, improperly
adjusted, or not completely and securely assembled. Be
sure that the saw’s chain stops moving when the throttle
control trigger is released.
• Shut off the motor before setting the chain saw down.
• Use extreme caution when cutting small-sized brush and
saplings because slender material may catch the chain
saw and whip towards you or pull you off balance.
• When cutting a limb that is under tension, be alert for
springback so that you will not be struck when the tension in the wood fibers is released
• Do not cut through nails, rods in the tree, railroad ties or
pallets. Inspect a tree that you are going to cut for foreign objects that could cause injury or damage to your
chain saw.
• After striking a foreign object, stop the engine and thoroughly inspect for damage. Repair as necessary.
• Keep the handles dry, clean and free of the oil/fuel mixture
• We do not recommend using the chain saw in a tree or
on a ladder.
• All chain saw service, other that the items listed in this
instruction manual maintenance instructions, should be
performed by competent chain saw service personnel.
• Use the right tool. Only use this chain saw for its intended purpose, to cut wood.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on all handles or grips.
• Never touch the chain or attempt to service the saw
while the engine is running. Make sure all moving parts
have stopped. Allow the chain saw to cool, as the chain
can be hot.
• Check the bar and chain at frequent intervals for proper
adjustment. Make sure the bar and chain are properly
tightened and sharpened. Visually inspect for damage.
Repair any damage before restarting or operating the
chain saw.
KICKBACK SAFETY PRECAUTIONS
WARNING:
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a lightning-fast reverse reaction, kicking the guide bar
up and back towards the operator. Pinching the
saw chain along the top of the guide bar may
push the guide bar rapidly back toward the operator. Either of these reactions may cause you to
lose control of the saw, which could result in serious personal injury.
Do not rely exclusively upon the safety devices
built into your saw. As a chain saw user, you
should take several steps to keep your cutting
jobs free from accident or injury.
• With a basic understanding of kickback, you can reduce
or eliminate the element of surprise. Sudden surprise
contributes to accidents. Be alert to the potential for kickback at all times.
• Keep a good firm grip on the pole saw with both hands,
the right hand on the handle and the left hand confortably
on the pole lower when the motor is running. A firm grip
will help you reduce kickback and maintain control of the
saw. Don’t let go.
• Make sure that the area in which you are cutting is free
from obstructions. Do not let the nose of the guide bar
contact a log, branch, fence, or any other obstruction
that could be hit while you are operating the saw.
• Always cut with the motor running at full speed. Fully
squeeze the throttle trigger and maintain a steady cutting
speed.
• Use only the correct original equipment manufacturer
replacement bars, chains and other parts and accessories. These are available from your authorized service
dealer. Use of any unauthorized parts or accessories
could lead to serious injury to the user, or damage to the
unit, and will void your warranty.
• Follow the manufacturer’s sharpening and maintenance
instructions for the saw chain.
• Use only the replacement guide bars and low kickback
chains specified for your saw to avoid injury.
KICKBACK may occur
when the nose or tip of the
3
RULES FOR SAFE OPERATION
Max. CKA 45˚
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and inter
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
national symbols and pictographs that may appear on this product.
SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning, or caution.
May be used in conjunction with
other symbols or pictographs.
• WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety instructions. Failure to do so can result in
serious injury to the operator and/or
bystanders.
• WEAR EYE, HEARING AND HARDHAT PROTECTION
WARNING: Thrown objects and loud
noise can cause severe eye injury and
hearing loss. Wear eye protection
meeting ANSI Z87.1-1989 standards
and ear protection when
operating this unit. Wear a hard hat.
Use a full face shield when needed.
SYMBOL MEANING
• GUIDE BAR WARNING:
Contact of the guide bar tip with any
object should be avoided. Tip contact
may cause the guide bar to move
suddenly upward and backward,
which may cause serious injury.
• USE BOTH HANDS
Always use both hands while operating the chain saw. Never use only one
hand to operate the saw.
Avoid bar nose contact.
This product has been tested at a
computed kickback angle (CKA) of no
greater than 45degrees.
4
RULES FOR SAFE OPERATION
1
3
2
5
12
10
17
18
2
19
4
7
14
8
9
6
16
1
10
21
20
3
13
11
15
6
9
CHAIN COMPONENTS
1.Saw Chain
2.Guide Bar
3.Front Handle
4.Handle Bracket
5.Pole Locking Nut
6.Power Cord
7.Height Adjuster Knob
8.Outer Pole
9.Lock-off Switch
10.Trigger Start/ Stop Switch
11.Rear Handle
12.Hand Guard
13.Oil Tank Cap
14.Electric Motor
15.Rear Hand Guard
16.Guide Bar Nose
17.Sprocket Cover
18.Chain Catcher
19.Bar Retaining Nuts
20.Spikes
21.Tension Adjustment Screw
SAFETY FEATURES
Numbers preceding the descriptions correspond with
the numbers on preceding page to help you locate the
safety feature.
1.LOW-KICKBACK CHAIN helps significantly reduce
kickback, or the intensity of kickback, due to specially designed depth gauges and Guard links.
9.LOCK / OFF BUTTON prevents accidental acceleration of the saw motor. The trigger cannot be
squeezed unless lock/off button is depressed.
10.TRIGGER START / STOP SWITCH stops saw
motor when released.
12.HAND GUARD protects the operator’s left hand in
the event it slips off the front handle while saw is
running.
14.ELECTRIC MOTOR is double insulated for added
safety.
18.CHAIN CATCHER reduces the danger of injury in
the event saw chain breaks or derails during operation. The catcher is designed to intercept a whipping
chain.
5
RULES FOR SAFE OPERATION
KICKBACK SPECIFICS
WARNING:
control of the chain saw and result in serious
or fatal injury to the saw operator or to anyone standing close by. Always be alert.
Rotational kickback and pinch-kickback are
major chain saw operational dangers and the
leading cause of most accidents.
Beware of:
Rotational Kickback
A
A
Kickback can lead to
dangerous loss of
B
A
KICKBACK SPECIFICS
Bewar
e of:
Pinch Kickback (The push and pull reactions)
A
B
C
A = Pull
B = Solid objects
C = Push
Fig.2
A = Kickback path
B = Kickback reaction zone
Fig.1
KICKBACK may occur when the NOSE or TIP of the guide
bar touches an object, or when wood closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a lightning-fast
reverse reaction, kicking the guide bar up and back
toward the operator.
PINCHING the saw chain along the BOTTOM of the guide
bar may PULL the saw forward away from the operator.
PINCHING the saw chain along the TOP of the guide bar
may PUSH the guide bar rapidly back toward the operator.
Any of these reactions may cause you to lose control of
the saw, which could result in serious personal injury.
6
IMPORTANT SAFETY INSTRUCTIONS
When using an electric
WARNING:
always be followed to reduce the risk of fire,
electric shock, and injury to persons, including
the following:
chain saw
precautions should
, basic safety
READ ALL INSTRUCTIONS
1.Double insulated - No Serviceable Parts Inside.
2.To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider then the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any
way.
3.With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
4.KEEP THE WORK AREA CLEAN: Cluttered areas
invite injuries. Do not start cutting until you have a
clear work area, secure footing, and a planned retreat
path from the falling tree.
5.GUARD AGAINST ELECTRIC SHOCK: Prevent body
contact with grounded surfaces (i.e., metal pipes, wire
fences).
6.CONSIDER THE WORK AREA ENVIRONMENT: Use
extreme caution when cutting small sized brush and
sapling, as slender material may catch the saw chain
and be whipped toward you or pull you off balance. Do
not operate a chain saw in a tree unless you are specifically trained to do so. When cutting a limb that is under
tension, be alert for spring back so that you will not be
struck when the tension in the wood fibers is released.
Do not expose the chain saw to rain. Do not use the
chain saw in damp or wet locations. Do not use the
chain saw in the presence of flammable liquids or
gases.
7.KEEP CHILDREN AND BYSTANDERS AWAY: Do not
let visitors contact the chain saw or extension cord. All
visitors should be kept away from the work area.
8.STORE THE IDLE CHAIN SAW: When not in use, chain
saws should be stored out of the reach of children, in a
dry, high or locked-up place. When storing saw, use a
scabbard or carrying case.
9.DO NOT FORCE THE CHAIN SAW: The chain saw will
do a better and safer job when used at the rate for which
it was intended.
10.USE THE RIGHT TOOL: Cut wood only. Do not use the
chain saw for purposes for which it was not intended.
For example, do not use the chain saw for cutting plastic, masonry, or non-building materials.
11.DRESS PROPERLY: Do not wear loose clothing or jewelry, as they can get caught in moving parts. Non-skid
footwear is recommended when working outdoors.
Wear protective hair covering to contain long hair.
12.USE SAFETY GEAR: Use safety glasses, safety
footwear, snug fitting clothing, protective gloves, and
protective hearing and head gear
13.STAY ALERT: Watch what you are doing. Use common
sense. Do not operate the chain saw when you are tired.
Keep all parts of your body away from the saw chain
when the motor is operating. Before you start the saw,
make sure the saw chain is not contacting anything.
14.MAINTAIN THE CHAIN SAW WITH CARE: Inspect the
chain saw cords periodically and, if damaged, have
them repaired by an authorized service facility. Keep the
cord clear of the chain and operator at all times. Never
carry the saw by the cord or pull it to disconnect from
receptacle. Keep the cord from oil and sharp edges.
Inspect the extension cords periodically and replace if
damaged. Keep tools sharp and clean for better and
safer performance. Follow instructions for lubricating
and changing accessories. Keep handles dry, clean and
free from oil and grease.
15.DISCONNECT THE CHAIN SAW: Disconnect the chain
saw when not in use, before servicing, and when changing accessories and attachments such as saw chain and
guard.
16.OUTDOOR EXTENSION CORDS: Use only extension
cords that are intended for outdoor use and which are so
marked.
17.CHECK DAMAGED PARTS: Before further use of the
chain saw, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by an
authorized service center, unless otherwise indicated in
this instruction manual.
18.CARRYING THE SAW: Carry the saw by the front handle with the saw stopped. Keep your finger off the
switch, and make sure that the guide bar and saw chain
are to the rear.
19.GUARD AGAINST KICKBACK:
WARNING:
the guide bar touches an object, or when the
wood closes in and pinches the saw chain in
the cut. Tip contact in some cases may cause a
lightning-fast reverse action, kicking the guide
bar rapidly back towards the operator. Pinching
the saw chain along the top of the guide bar
may push the guide bar rapidly back towards
the operator. Either of these reactions may
cause you to lose control of the saw, which
could result in serious injury to the user. The following precautions should be followed to minimize kickback.
7
.
Kickback may occur
when the nose or tip of
A.
GRIP SAW FIRMLY: Hold the chain saw firmly with
both hands when the motor is running. Keep a
good firm grip on the saw with both hands, the right
hand on the rear handle, and the left hand on the
front handle.
B. Do not over reach.
C.
Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a log,
branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide bar
nose guards, chain brakes and special guide bars,
which reduce the risks associated with kickback.
G. Use only replacement bars and chains specified by
the manufacturer or the equivalent.
H. There are no other replacement components for
achieving kickback protection in accordance with
CSA Z62.3.
20.POWER SUPPLY: Connect the chain saw to correct
voltage; be sure that the voltage supplied is the same
as that specified on the nameplate of the tool.
21.DO NOT operate a chain saw that is damaged,
improperly adjusted, or not completely and securely
assembled. Be sure that the saw chain stops moving
when the trigger is released.
22.DO NOT attempt operations beyond your capacity or
experience.
23.DO NOT operate a chain saw with one hand! Serious
injury to the operator, helpers, or bystanders may
result from one-handed operation. A chain saw is
intended for two-handed use.
24.TO REDUCE potential for electric shock, do not operate the saw on wet or slippery surfaces, or during
snow storms, rain storms, and other adverse weather
conditions.
25.DO NOT allow dirt, debris or sawdust to build up on
the motor or outside air vents.
26.Follow the manufacturer’s sharpening and maintenance instructions for the saw chain.
27.Cut at high motor speeds.
28.Operation of a chain saw should be restricted to
mature, properly instructed individuals.
29.Your chain saw is intended for occasional homeowner
use. It is not made for heavy continuous use.
30.DO NOT FORCE a small saw to do a job requiring a
heavier duty unit.
31.EXAMINE
THE ELECTRICAL SWITCHES. Do not use
the chain saw if the switches do not properly turn on and
off. Do not attempt to make any repairs to the electric
switches. Take your saw to a MTD Authorized Service
Center
.
32.MAINTAIN EXTENSION CORDS. Inspect the extension cords periodically and replace if damaged. Only
use power cords that are suitably marked for outdoor
use.
33.DO NOT OPERATE YOUR CHAIN SAW near or
around flammable liquids or gases, whether in or out
of doors. An explosion and/or fire may result.
34.This electric powered saw is classified by CSA as a
Class 2C saw. It is intended for infrequent use by
homeowner’s, cottagers and campers, and for such
general applications such as clearing, pruning, cutting
firewood, etc. It is not intended for prolonged use. If
the intended use involves prolonged periods of operation, this may cause circulatory problems in the user’s
hands due to vibration. It may be appropriate to use a
saw having an anti-vibration feature.
35.NEVER REMOVE, modify or make inoperative any
safety device furnished with your unit.
36.Safety clothing required by your safety organizations,
government regulations, or your employer should be
used; otherwise, snug fitting clothing, safety footwear,
and hand and ear protection should be worn.
37.When felling, keep at least 2 tree lengths between
yourself and your fellow workers.
38.All chain saw service, other than the items listed in the
user manual safety and maintenance instructions,
should be performed by competent chain saw personnel. Do not attempt to repair it yourself; there are no
user serviceable parts inside.
NOTE:
Low-kickback saw chain is chain that has met the
kickback performance requirements of ANSI B175.1-1991
and is in accordance with CSA Z62.3. Do not use other
replacement chain unless it has met these requirements for
your specific model.
39.
DO NOT USE ANY OTHER CUTTING ATTACH-
MENT OR ACCESSORIES. Use only MTD
replacement parts and accessories, which are designed
specifically to enhance the performance and maximize
the safe operation of our products. Failure to do so may
cause poor performance and possible injury. Use only
the chain and bar supplied with this product. Do not use
any other cutting attachment. Use of such attachments
will void your factory warranty and could result in serious
bodily injury.
8
POLE SAW TRIMMING PRECAUTIONS
1. Be aware of extension cord while operating chain saw.
Be careful not to trip over cord. Keep cord away from
chain and operator at all times.
2. Keep bystanders 50 feet (15 meters) away when operating saw.
3. Do not use the pole saw to cut down trees. Use the
chain saw without pole attachment.
4.
Grip pole saw securely - one hand on the pole, the other
on the handle.
5. Keep finger off trigger until ready to make cut.
6. Before starting pole saw, make sure chain is not touching anything.
7. Keep all parts of body away from chain when saw is running.
8. Do not force chain saw while cutting. Apply light pressure. It will do the job better and safer at the rate for
which it was intended.
9. When cutting limbs or branches that are under tension,
use extreme caution. Be alert for wood springing back.
When wood tension is released, limb could spring back
and strike operator causing severe injury or death.
10.When Carrying pole saw from one place to another: •
unplug unit • return telescoping pole to shortest position
• hold pole at balance point (close to saw end) • keep
guide bar and chain to rear
11.Do not cut small brush and saplings with the pole saw.
Use the chain saw only, with extreme care. Slender
matter may catch in the chain and be whipped toward
you. This could also pull you off balance.
12.Never stand directly under the limb you are trimming.
Always position yourself out of the path of falling debris.
(See Fig. A)
13.Never stand on a ladder or other type of unstable support while using the pole saw.
14.Always use both hands to operate pole saw. Keep a
firm, steady pressure on the pole saw while cutting but
do not try to force the saw through the wood.
15.Do not use the pole saw to cut limbs larger in diameter
than 4” (10 cm) in diameter. (See Fig.B)
16.Keep other persons away from cutting end of pole saw
and at a safe distance from work area. (See Fig. C)
17.Do not use pole saw near cable, electric power or telephone lines. Maintain a minimum clearance of 10 feet
from all power lines. (See Fig.D)
Fig.B
Fig.C
Fig.A
Fig.D
SAVE THESE
INSTRUCTIONS
9
ASSEMBLY INSTRUCTIONS
INTRODUCTION
This unit is designed for occasional homeowner use and
should not be used for commercial purposes or subjected
to heavy continuous use.
Your new chain saw can be used for a variety of projects
such as cutting firewood, making fence posts, felling small
trees, limbing, pruning at ground level, and light carpentry.
Cut only wood or wood products with your saw.
Guide Bar Bolts
Boulons du guide-chaîne
Tornillos de la Barra Guia
Saw Chain
Chaîne
Motosierra
UNPACKING
1. Remove all items from carton.
2. Check all items for any shipping damage. If you find any
damage or if any parts are missing, promptly inform
dealer where you bought the pole saw.
ASSEMBLY REQUIREMENTS
Your new pole saw will require adjustment of chain and filling the oil tank with lubricating oil before the unit is ready
for operation. Do not start the saw motor until the unit is
properly prepared.
Read all instructions carefully. Do not install any other size
bar and chain than what is recommended for your model.
GUIDE BAR / SAW CHAIN REPLACEMENT
INSTALLATION
WARNING:
gloves for protection against sharp cut ting
edges.
1. Remove bar nuts, push bar bolts in and slide sprocket
support down. (See Fig. 3)
2. Remove old guide bar and chain.
3. Using a straight screwdriver, turn the chain adjustment
screw counterclockwise as far as it will go, or until tang
is to the end of its travel.
4. Loop saw chain over drive sprocket with the cutting
edges of the chain pointing in the direction of rotation.
5. Place the slotted end of guide bar over the bar bolt so
the tang fits into the lower hole in the guide guide bar.
6. Make sure the chain follows the slot in the guide bar.
Slide the sprocket support up and push the bar bolts
through the sprocket support.
7. Install the bar retaining nuts hand tight, (Proceed to saw
chain tension Adjustment).
..
Whenever handling the
saw chain, wear work
Adjusting Hole
Orifice de réglage
Orificio de Ajuste
Drive Sprocket
Pignon d’entraîne-
ment
Engrane
Tang
Tenen
Espiga
Fig.3
Guide Bar Nuts
Ecrous du guide-chaîne
Tuercas de Barra Guia
Adjusting Plate
Plaque de
réglage
Placa de Ajuste
Adjusting Screw
Vis de réglage
Tornillo de
Ajuste
Sprocket Support
Support du pignon
Soporte del
Engrane
SAW CHAIN TENSION ADJUSTMENT
Proper tension of the saw chain is extremely important and
must be checked before starting, as well as during, any cutting operation. Taking the time to make needed adjustments to the saw chain will result in improved cutting performance and prolonged chain life.
NOTE:
few as 5 cuts. This is normal during the break-in period,
and the interval between future adjustments will lengthen
quickly (Figure 5).
TO ADJUST SAW CHAIN TENSION:
1. Loosen the bar retaining nuts (D) so they are hand tight.
10
A new chain and bar will need readjustment after as
If a chain is TOO LOOSE
CAUTION:
or TOO TIGHT, the bar
chain and saw bearings
will wear more rapidly. Study Figure 4 for information concerning correct cold tension (A),
correct warm tension (B), and as a guide for
when saw chain needs adjustment (C).
(See Fig. 4)
Guide Bar
Guide-chaîne
Barra Guia
ASSEMBLY INSTRUCTIONS
3. After adjustment and while wearing heavy duty work
gloves, move the saw chain back and forth on the guide
bar to be sure the chain moves freely and is in proper
mesh with sprocket. Do not move chain with bare
hands.
NOTE:
IF the chain is difficult to rotate or if it binds on the
guide bar, too much tension has been applied and must be
adjusted. To decrease tension, turn the adjustment screw
A
B
C
counterclockwise slowly. Move the chain back and forth
until it moves freely.
4. Holding the nose in upper position, securely tighten the
bar retaining nuts (70 inch lbs.)
Fig.4
ASSEMBLY OF POLE SAW
1. Make sure the unit is unplugged from power source.
2. Slip handle bracket (A) over chain saw handle from the
right side (See Fig. 7).
NOTE:
The trigger must be depressed before the bracket
will go onto the handle. Push the lock-off button and
D
depress the trigger. While holding the trigger in, place
the trigger support portion of the bracket under the trigger and slide the bracket onto the chain saw handle.
The bracket will keep the trigger in the “ON” position.
A
Fig.5
E
Fig.6
2. Holding the nose of the bar up, use the screwdriver or
scrench if provided in your User’s Kit to turn the guide
bar adjustment screw (E) (Fig. 6) clockwise to tighten
the chain. Turning the screw COUNTERCLOCKWISE
LOOSENS THE CHAIN on the guide bar.
B
Fig.7
3. Align holes in pole bracket with holes in handle bracket.
Install Phillips head screws with lock washers through
pole bracket from left side and thread into the weld nuts
on the handle bracket. Tighten screws securely.
4. Plug the saw power cord into receptacle cord at end of
inner pole.
ADJUSTING POLE LENGTH
The pole saw has a telescoping pole assembly that will
extend from 57 inches (fully retracted) to 96 inches (fully
extended). A threaded compression coupling is used to
hold the pole in position at any extended length.
1
1
ASSEMBLY INSTRUCTIONS
UNLOCK
ÉVERROUILLEZ
D
ABRA
Fig.8
1. To extend the pole, loosen coupling by turning coupling
nut counterclockwise as shown in Fig. 8. Pole will slide
freely.
2. Pull inner pole section out to desired length of extension.
Note: Only extend pole to minimum length
required to reach limb that is being cut.
3. To lock pole in position, tighten coupling by turning coupling nut clockwise (See Fig. 8) until firmly hand tight.
Make sure saw handle is aligned with pole handle
before tightening coupling nut.
IMPORTANT: Do not use wrench or pliers to overtighten coupling. Damage to coupling or pole may result.
OILING CHAIN
To oil chain, press oil cap. Oil will feed onto guide bar and
chain. Press oil cap at least once before each cut. Always
check oil level before using pole saw. check oil level often
by looking at oil sight level hole. Oil sight level hole is on left
side of saw, between front handle and front hand guard. Do
not attempt to operate the oiler while cutting with the pole
saw.
Grip Area
Zone de Poignée
Área del Apretón
LOCK
SERRURE
BLOQUEO
CUTTING WITH THE POLE SAW
1.
Connect saw to extension cord. Connect extension cord
to power supply.
2. Use both hands to grip pole saw. Use only designated
grip areas when operating pole saw (See Fig. 9). Use
firm grip. Thumbs and fingers must wrap around pole
saw handle and pole.
3. Make sure your footing is firm. Keep feet apart. Divide
your weight evenly on both feet.
4. When ready to make a cut, press in trigger switch lockoff and squeeze trigger switch (see Fig. 10) This will
turn pole saw on. Releasing trigger switch will turn pole
saw off. Make sure saw is running at full speed before
starting a cut.
5. When starting a cut, place moving chain against wood.
Hold pole saw firmly in place to avoid possible bouncing
or skating (sideways movement) of saw.
6. Guide pole saw using light pressure. Do not force pole
saw. The motor will overload and can burn out. It will do
the job better and safer at the rate for which it was
intended.
7. Remove pole saw from a cut with saw running at full
speed. Stop pole saw by releasing trigger. Make sure
chain has stopped before setting pole saw down.
8. Never stand directly under the limb you are trimming.
Always position yourself out of the path of falling debris.
FILLING OIL TANK
Using a funnel, fill oil tank with MTD Chain, Bar and
Sprocket oil. Wipe up any spills. Make sure no dirt gets into
the oil tank.
SELECTING THE PROPER EXTENSION CORD
FOR YOUR SAW MODEL
Fig.9
Lock-Off Switch
Gâchette de Contact
Fijador del Interruptor
Fig.10
rigger Switch
T
Interrupteur de Gachette
Interruptor de Gatillo
Minimum Gauge Wire
Saw Model
MTD PS
Ampere
Rating
8
Volts AC
110 / 120
Fig.11
Length of Power Cord
25 ft. / 7.5m 50 ft. / 15m
18 Gauge 16 Gauge
1. When using the appliance, an extension cord of ade-
quate size must be used for safety and to prevent loss
of power and overheating.
2. The extension cord must be specifically intended for out-
door use and marked SW-A, SOW-A, STOW-A, SJW-A,
SJOW-A SJTOW-A, SJTW-A, OR SJTW.
12
100 ft. / 30m
14 Gauge
OPERATING INSTRUCTIONS
CUTTING WITH ONLY THE CHAIN SAW.
1. PLEASE READ ALL WARNINGS.
2. Make sure oil reservoir is full.
WARNING:
size and type for your saw.
3. Plug the cord (A) into the appropriate size extension
cord (B) (see Figure 11). Plug the extension cord into a
110/120 volt AC, 15 AMP receptacle (Figure 12).
Ensure the extension
cord is of the proper
A
5. With your RIGHT THUMB, depress the LOCK/OFF button (C) on the side of the rear handle, and at the same
time squeeze the trigger
trigger (Figure14).
NOTE:
It is not necessary to maintain pressure on the
LOCK/OFF button once the trigger is squeezed and the
motor is running. The LOCK/OFF button is a safety
device to avoid accidental starting.
. To stop the saw, release the
B
Fig.12
WARNING:
come in contact with the guide bar and saw
chain.
4. Grip the saw with both hands, left hand holding the and
the right hand holding the handle. Thumbs and fingers
should encircle both handles (Figure 13).
Make sure the extension cord does not
Fig.13
C
Fig.14
TO STOP MOTOR
The saw motor will automatically stop when the trigger is
released. The LOCK/OFF button will have to be depressed
and the trigger squeezed to restart the motor.
13
OPERATING INSTRUCTIONS
CHAIN AND BAR LUBRICATION
Always check oil level before using saw. To oil chain, press
oil cap. Do not attempt to operate the oiler while cutting
with the saw
oil cap at least once before each cut. Check oil level often
by looking at oil sight level hole. Oil sight level hole is on left
side of saw, between front handle and front hand guard.
NOTE:
when it is new, and occasional adjustment will be needed.
A new chain requires more frequent adjustment during the
break-in period. This is normal. See Page 10 for Saw Chain
Tension Adjustment instructions.
. Oil will feed onto guide bar and chain. Press
Never starve the bar and
CAUTION:
with TOO LITTLE OIL will decrease cutting efficiency, shorten chain saw life, and cause rapid
dulling of the chain and excessive wear of the
bar from overheating. Too little is evidenced by
smoke or bar discoloration.
The saw chain stretches during use, particularly
WARNING/
CAUTION:
chain that is too tight can damage the saw.
Either situation, chain too loose or too tight,
could cause serious personal injury.
chain of lubrication oil.
Running the saw DRY or
A loose chain can jump
off the bar while you are
cutting, as well as wear
the bar and chain. A
EXTENSION CORDS
When using an electric chain saw, plug it into the extension
cord only when you are ready to cut wood. Connect the
extension cord to a 110/120 voltage outlet.
NOTE:
a loose knot before connecting the ends together (Figure
15).
To prevent disconnection of the extension cord, tie
A
cord that is hot to the
CAUTION:
1. When using the appliance, an extension cord of adequate size must be used for safety and to prevent loss
of power and overheating.
2. The extension cord must be specifically intended for outdoor use and marked SW-A, SOW-A, STW-A, STOW-A,
SJW-A, SJOW-A, SJTOW-A, STJW, or SJTW.
3. Inspect the extension power cord for loose or exposed
wires and damaged insulation. If damaged, replace
before using the appliance.
touch is overloaded.
DOUBLE INSULATION
Do not operate your
WARNING:
not expose the saw to rain, snow or sleet.
Moisture will cause short circuits. Replace or
repair any damaged or frayed extension cords
before using your saw.
Keep the cord away from the cutting area and
position the cord so that it will not be caught on
branches or other objects during cutting.
chain saw in a wet or
damp environment. Do
NO SERVICEABLE PARTS INSIDE
Do not use if the cord or plug is damaged. Your appliance
is double insulated to help protect against electric shock.
Double insulation construction consists of 2 separate “layers” of electrical insulation.
Appliances built with this insulation system are not intended to be grounded. As a result, the extension cord used
with your appliance can be plugged into any conventional
120 volt electrical outlet.
Normal safety precautions must be observed when operating an electrical appliance. The double insulation system is
only for added protection against injury resulting from a possible internal electrical insulation failure.
Fig.15
14
Your double insulated
WARNING:
not attempt to repair it yourself. For service
information, contact the MTD Product Service
Department toll-free number listed on the back
cover of this manual.
appliance has no serviceable parts inside. Do
GENERAL CUTTING INSTRUCTIONS GENERAL CUTTING INSTRUCTIONS
TRIMMING A TREE (PRUNING)
Avoid kickback. Kickback
WARNING:
page 6, to avoid risk of kickback.
Do not operate pole saw while in a tree, on a
ladder or any other unstable work surface, or in
any awkward position. You may lose control of
pole saw causing severe injury.
Do not extend arms above shoulders when
using pole saw.
Seek professional help if facing conditions
beyond your ability.
Trimming a tree is the process of cutting limbs from a living
tree. Make sure footing is firm. Keep feet apart. Divide your
weight evenly on both feet.
1. Make first cut six inches from tree trunk on underside of
limb. Use top of guide bar to make this cut. (Cut 1/3
through diameter of limb, see Fig. 16)
2. Move two to four inches farther out on limb. Make second cut from above limb. make second cut from above
limb. Continue cut until you cut limb off.
3. Make third cut as close to tree trunk as possible on
underside of limb stub. Use top of guide bar to make this
cut. Cut 1/3 through diameter of stub.
4. Make fourth cut directly above third cut. Cut down to
meet third cut. This will remove limb stub.
can result in severe injury
or death. See Kickback,
FELLING
Felling is the term for cutting down a tree. Small trees up
to 6-7” (15-18cm) in diameter are usually cut in a single
cut. Larger trees require notch cuts. Notch cuts determine
the direction the tree will fall.
FELLING A TREE:
A retreat path (A)
WARNING:
cleared as necessary before cuts are started.
The retreat path should extend back and diagonally to the rear of the expected line of fall, as
illustrated in Figure 17.
NOTE:
Before any cuts are made, consider the location of larger
branches and natural lean of the tree to determine the way
the tree will fall.
Direction of fall (B) is controlled by the notching cut.
CAUTION:
keep on the uphill side of the terrain, as the tree
is likely to roll or slide downhill after it is felled.
should be planned and
If felling a tree on sloping ground, the chain
saw operator should
4
6”
3
Fig.16
2
B
2” - 4”
1
A
Fig.17
Do not cut down a tree
WARNING:
winds or if there is a danger to property. Consult
a tree professional.
Do not cut down a tree if there is a danger of
striking utility wires; notify the utility company
before making any cuts.
15 16
during high or changing
GENERAL GUIDELINES FOR FELLING
TREES:
Normally felling consists of 2 main cutting operations,
notching (C) and making the felling cut (D).
Start making the upper notch cut (C) on the side of the tree
facing the felling direction (E). Be sure you don’t make the
lower cut too deep into the trunk.
The notch (C) should be deep enough to create a hinge (F)
of sufficient width and strength. The notch should be wide
enough to direct the fall of the tree for as long as possible.
G
H
Fig.19
3
/4
D
3-5cm
WARNING:
Make the felling cut (D) from the other side of
the tree and 1.5” - 2.0” (3-5cm) above the edge
of the notch (C) (Figure 18).
Never saw completely through the trunk. Always leave a
hinge. The hinge guides the tree. If the trunk is completely
cut through, control over the felling direction is lost.
Insert a wedge or felling lever in the cut well before the tree
becomes unstable and starts to move. This will prevent the
guide bar from binding in the felling cut if you have misjudged the falling direction. Make sure no bystanders have
entered the range of the falling tree before you push it over.
Fig.18
1
/4
F
Never walk in front of a
tree that has been
notched.
E
C
FELLING CUT:
1. Use wooden or plastic wedges (G) to prevent binding
the bar or chain (H) in the cut. Wedges also control
felling (Figure 19).
2. When diameter of wood being cut is greater than the bar
length, make 2 cuts as shown (Figure 20).
WARNING:
When tree begins to fall, remove saw from cut,
stop engine, put chain saw down, and leave
area along retreat path (Figure17).
Fig.20
As the felling cut gets
close to the hinge, the
tree should begin to fall.
WARNING:
final cut, always
recheck the area for
bystanders, animals or obstacles.
Before making the
GENERAL CUTTING INSTRUCTIONS
LIMBING
Limbing a tree is the process of removing the branches
from a fallen tree. Do not remove supporting limbs(A)until
after the log is bucked (cut) into lengths (Figure 21).
Branches under tension should be cut from the bottom up
to avoid binding the chain saw
WARNING:
tree trunk
.
Never cut tree limbs
while standing on
Fig.21
Fig.24
2. Log supported on 1 end: First, cut from bottom (underbuck) 1/3 diameter of log to avoid splintering. Second,
cut from above (overbuck) to meet first cut and avoid
pinching (Figure 23).
3. Log supported on both ends: First, overbuck 1/3 diameter of log to avoid splintering. Second, underbuck to
meet first cut and avoid pinching (Figure24).
NOTE:
a sawhorse. When this is not possible, the log should be
raised and supported by the limb stumps or by using supporting logs. Be sure the log being cut is securely supported.
The best way to hold a log while bucking is to use
BUCKING USING A SAWHORSE
For personal safety and ease of cutting, the correct position
for vertical bucking is essential (Figure 25).
Fig.22
BUCKING
Bucking is cutting a fallen log into lengths. Make sure you
have a good footing and stand uphill of the log when cutting on sloping ground. If possible, the log should be supported so that the end to be cut off is not resting on the
ground. If the log is supported at both ends and you must
cut in the middle, make a downward cut halfway through
the log and then make the undercut. This will prevent the
log from pinching the bar and chain. Be careful that the
chain does not cut into the ground when bucking as this
causes rapid dulling of the chain.
When bucking on a slope, always stand on the uphill side.
1. Log supported along entire length: Cut from top (overbuck), being careful to avoid cutting into the ground
(Figure 22).
B
A
C
Fig.25
VERTICAL CUTTING:
A. Hold the saw firmly with both hands and keep the saw to
the right of your body while cutting.
B Keep the left arm as straight as possible.
C. Keep weight on both feet.
Fig.23
17
CAUTION:
ting, be sure the
chain and bar are being properly lubricated.
While the saw is cut-
MAINTENANCE INSTRUCTIONS
GUIDE BAR MAINTENANCE
WARNING:
forming any maintenance on your saw.
Fig.26
Proper maintenance of the guide bar, as explained in
this section, is essential to keep your saw in good
working order.
Ensure that the
power cord is disconnected before per-
GUIDE BAR MAINTENANCE :
Most guide bar problems can be prevented merely by
keeping the chain saw well maintained.
Incorrect filing and non-uniform cutter and depth gauge settings cause most guide bar problems, primarily resulting in
uneven bar wear. As the bar wears unevenly, the rails
widen, which may cause chain clatter and difficulty in making straight cuts.
Insufficient guide bar lubrication and operating the saw with
a chain that is TOO TIGHT will contribute to rapid bar wear
.
To help minimize bar wear, the following guide bar maintenance is recommended.
BAR WEAR - Turn guide bar frequently at regular intervals
(for example, after 5 hours of use), to ensure even wear on
top and bottom of bar.
BAR GROOVES - Bar grooves (or rails which support and
carry the chain) should be cleaned if the saw has been
heavily used or if the saw chain appears dirty. Rails should
always be cleaned every time the saw chain is removed.
OIL PASSAGES - Oil passages at bar pad should be
cleaned to ensure proper lubrication of the bar and chain
during operation. This can be done using a soft wire small
enough to insert into the oil discharge hole.
To Clean Guide Bar Rails:
1.
Remove sprocket cover, bar and chain .
2.
Using a screwdriver, putty knife, wire brush or other sim-
ilar instrument, clear residue from the rails on the guide
bar.
This will keep the oil passages open to provide proper
lubrication to the bar and chain (Figure 26).
3. Reinstall the bar, chain and bar bolt retaining nuts. .
CHAIN MAINTENANCE INSTRUCTIONS
WARNING:
training for dealing with kickback (see Safety
Precautions), always use a low-kickback saw
chain, which significantly reduces the danger of
kickback. Low-kickback saw chain does not
completely eliminate kickback.
A low-kickback or “safety chain”, should never be regarded
as total protection against injury.A low-kickback saw chain
should always be used in conjunction with other kickback
protection devices such as the Hand Guard furnished with
your unit.
Always use a replacement saw chain designed as “lowkickback” or a saw chain which meets the low-kickback
performance.
A standard saw chain (a chain which does not have the
kickback reducing guard links) should only be used by an
experienced professional chain saw operator.
Unless you have experience and specialized
What is a Low-Kickback Saw Chain?
A low-kickback saw chain is a chain which has met the
kickback performance requirements of ANSI B175.1. Do
not use other replacement chain unless it has met these
requirements for your specific model.
By keeping the saw chain in good working condition and
correctly serviced as recommended in this manual, you will
be able to maintain the safety system of your chain saw
over the life of the product.
18
MAINTENANCE INSTRUCTIONS PARTS LIST
No. Parts No. Description No. Parts No. Description
1 6097-210808 LABEL
24 6066-210801 OILER
2 6SDABB04-18 SCREW
3 6038-210801 HOUSING (R)
4 6NHZ-1/4 NUTS
5 6214-210802 FIXED SCREW
6 6043-210801 SPROCKET SUPPORT
7 6073-210802 SPROCKET-GEAR
8 6131-210801 ROLLER BRARING
9 6073-210801 MOTOR GEAR
10 6SDABB04-14 SCREW
11 6086-210801 MOTOR COYER ASSEMBLY
12 6272-830301 RUNNER STICK
13 6SQABB05-55 SCREW
14 6263-210801 WIND GUIDE
15 6MB-608-06 BEARING
16 6260-210802 ARMATURE ASS'Y
17 6220-210801 10" CHAIN
18 6040-210030 10" BAR
19 6MB-607-07 BEARING
20 6156-830401 ANTI-VIBRATILLAGE PAD
21 6261-210802 FIELD ASS'Y
22 6014-210801 ANTI-SPILLAGE PAD
23 6102-210801 ADJUSTING PLATE
25 6214-210801 REGULATION SCREW
26 6056-210802 REGULATION CAP
27 6067-210801 OIL CAP
28 6022-210803 LOCK-OFF SWITCH
29 6011-210802 POWER CORD
30 6216-830601 BRUSH 2
31 6017-210801 FRONT-HAND GUARD
32 6SXDZ-1/4-60 SCREW
33 6097-210809 WARNING TAG
34 6038-210802 HOUSING (L)
35 6086-210802 REAR COVER
36 6052-210842 LABEL
37 6159-830601 BRUSH SETS
38 6014-210802 ANTI-SPILLAGE
39 6SVABB3.5-12 SCREW
40 6SDABB04-40 SCREW
41 6086-210803 LEFR-CASE
42 6043-210803 MOUNT PLATE
43 6072-210801 FIXTURE
44 6087-210801 BUSHING
45 6228-210814 INNER PIPE ASS'Y
45-1 6022-210803 TRIGGER
45-2 6011-210806 POWER CORD
45-3 6154-210801 SOCKET
Never remove, modify
WARNING:
or make inoperative
any safety device furnished with your unit.
The Hand Guard and low-kickback saw
chain are major safety features provided for
your protection.
PREVENTATIVE MAINTENANCE
WARNING
SERVICING A DOUBLE INSULATED APPLIANCE
In this double insulated appliance, 2 systems of insulation,
instead of grounding, are provided. No grounding means is
provided on a double insulated appliance, nor should a
means for grounding be added to the appliance. No serv-
WARNING:
duty protection work
gloves and disconnect the extension cord
when working on the saw chain.
Always wear heavy
iceable parts are inside. A double insulated appliance is
marked with the words, “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol (square within a
square) may also be marked on the appliance.
CHAIN TENSION:
Check the chain tension frequently and adjust as often as
necessary to keep the chain snug on the bar, but loose
enough to be pulled around by hand. ( Saw Chain Tension
Adjustment).
1. Place switch in OFF position and unplug the power supply before the appliance is serviced, cleaned, or maintenance is performed.
2. Keep the air intake clean and air vents free of debris to
avoid overheating the motor.
3. Clean with a damp sponge and mild soap. Do not squirt
BREAKING IN A NEW SAW CHAIN
A new chain and bar will need readjustment after as few as
5 cuts. This is normal during the break-in period, and the
interval between future adjustments will begin to lengthen
quickly.
Over a period of time, however, the moving parts of the saw
chain will become worn, resulting in what is called CHAIN
STRETCH. This is normal. When it is no longer possible to
obtain correct chain tension adjustment, a link will have to
be removed to shorten the chain. See your MTD Authorized
Service Center to have this repair performed.
WARNING/
CAUTION:
cause damage to the sprocket.
Never have more than 3
links removed from a
loop of chain this could
19
with a water hose or douse with water or other liquids.
4. Inspect the saw chain for proper tension before each
use and frequently during cutting. Sharpen as required.
5. Clean the guide bar and bar pad to ensure free path for
oil.
6. Turn the bar over after each use to achieve even wear.
7. No motor lubrication is necessary. The motor is
equipped with lifetime lubricated bearings.
8. If the saw does not operate, turn switch to OFF position
and disconnect the extension cord, first from the power
supply, then from the saw. Check the power supply for
blown fuses or tripped circuit breakers. If it still does not
operate, contact the MTD Product Service Department,
through the toll-free number listed on the back cover of
this manual, for service information. Do not attempt to
repair it yourself. No serviceable parts are inside.
No. Parts No. Description No. Parts No. Description
1 6097-210808 LABEL
24 6066-210801 OILER
2 6SDABB04-18 SCREW
3 6038-210801 HOUSING (R)
4 6NHZ-1/4 NUTS
5 6214-210802 FIXED SCREW
6 6043-210801 SPROCKET SUPPORT
7 6073-210802 SPROCKET-GEAR
8 6131-210801 ROLLER BRARING
9 6073-210801 MOTOR GEAR
10 6SDABB04-14 SCREW
11 6086-210801 MOTOR COYER ASSEMBLY
12 6272-830301 RUNNER STICK
13 6SQABB05-55 SCREW
14 6263-210801 WIND GUIDE
15 6MB-608-06 BEARING
16 6260-210802 ARMATURE ASS'Y
17 6220-210801 10" CHAIN
18 6040-210030 10" BAR
19 6MB-607-07 BEARING
20 6156-830401 ANTI-VIBRATILLAGE PAD
21 6261-210802 FIELD ASS'Y
22 6014-210801 ANTI-SPILLAGE PAD
23 6102-210801 ADJUSTING PLATE
25 6214-210801 REGULATION SCREW
26 6056-210802 REGULATION CAP
27 6067-210801 OIL CAP
28 6022-210803 LOCK-OFF SWITCH
29 6011-210802 POWER CORD
30 6216-830601 BRUSH 2
31 6017-210801 FRONT-HAND GUARD
32 6SXDZ-1/4-60 SCREW
33 6097-210809 WARNING TAG
34 6038-210802 HOUSING (L)
35 6086-210802 REAR COVER
36 6052-210842 LABEL
37 6159-830601 BRUSH SETS
38 6014-210802 ANTI-SPILLAGE
39 6SVABB3.5-12 SCREW
40 6SDABB04-40 SCREW
41 6086-210803 LEFR-CASE
42 6043-210803 MOUNT PLATE
43 6072-210801 FIXTURE
44 6087-210801 BUSHING
45 6228-210814 INNER PIPE ASS'Y
45-1 6022-210803 TRIGGER
45-2 6011-210806 POWER CORD
45-3 6154-210801 SOCKET
20
Loading...