MTD H Style 600 User Manual

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

OperatOr’s Manual

600-Series Snow Thrower — C/D Style

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

Form No. 769-01274F

(June 26, 2007)

To The Owner

Thank You

Thank you for purchasing a Snow Thrower manufactured by
MTD LLC. It was carefully engineered to provide excellent
performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.

All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the unit, its
features and operation. Please be aware that this Operator’s
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. MTD LLC
reserves the right to change product specifications, designs and
equipment without notice and without incurring obligation.

Table of Contents

Important Safe Operation Practices ..................... 3

Assembly & Set-Up .................................................. 6

Controls & Features ................................................10

Operation ................................................................13

1

This product has met the rigid safety standards of the Outdoor
Power Equipment Institute and an independent testing
laboratory. If you have any problems or questions concerning
the machine, phone your local authorized MTD service dealer
or contact us directly. MTD’s Customer Support telephone
numbers, website address and mailing address can be found on
this page. We want to ensure your complete satisfaction at all
times.

Throughout this manual, all references to right and left side of the
machine are observed from the operating position.

The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer’s
Owner’s/Operator’s Manual, packed separately with your
machine, for more information.

Maintenance & Adjustment .................................15

Service .....................................................................18

Troubleshooting .................................................... 22

Replacement Parts ................................................ 23

Record Product Information

Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by standing at the operator’s position and looking
at the lower, rear section of the frame. This information will
be necessary, should you seek technical support via our web
site, Customer Support Department, or with a local authorized
service dealer.

MOdel nuMber

serial nuMber

Customer Support

Please do NOT return the unit to the retailer or dealer without first contacting our Customer Support Department.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this unit, you can seek help from the experts. Choose from the options below:

Visit us on the web at www.mtdproducts.com

◊

Call a Customer Support Representative at [phone] or [phone]

◊

Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

◊

2

Important Safe Operation Practices

WARNING: This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!

CALIFORNIA PROPOSITION 65

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.

DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating fingers, hands,
toes and feet and throwing foreign objects. Failure to observe the following safety
instructions could result in serious injury or death.

2

Training

1.

Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.

2.

Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them
quickly.

3.

Never allow children under 14 years of age to operate this
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and be trained and supervised by an
adult.

4.

Never allow adults to operate this machine without proper
instruction.

5.

Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.

6.

Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.

7.

Exercise caution to avoid slipping or falling, especially
when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used.
Remove all doormats, newspapers, sleds, boards, wires and other
foreign objects, which could be tripped over or thrown by the
auger/impeller.

Always wear safety glasses or eye shields during operation

1.
and while performing an adjustment or repair to protect
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.

Do not operate without wearing adequate winter outer

2.
garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.

Use a grounded three-wire extension cord and receptacle

3.
for all machines with electric start engines.

Adjust collector housing height to clear gravel or crushed

4.
rock surfaces.

Disengage all control levers before starting the engine.

5.

Never attempt to make any adjustments while engine is

6.
running, except where specifically recommended in the
operator’s manual.

Let engine and machine adjust to outdoor temperature

7.
before starting to clear snow.

3

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes which can ignite.
Wash your skin and change clothes immediately.

Use only an approved gasoline container.

a.

Extinguish all cigarettes, cigars, pipes and other

b.

sources of ignition.

Never fuel machine indoors.

c.

Never remove gas cap or add fuel while the engine is

d.

hot or running.

Allow engine to cool at least two minutes before

e.

refueling.

Never over fill fuel tank. Fill tank to no more than ½

f.

inch below bottom of filler neck to provide space for
fuel expansion.

Replace gasoline cap and tighten securely.

g.

If gasoline is spilled, wipe it off the engine and

h.

equipment. Move machine to another area. Wait 5
minutes before starting the engine.

Never store the machine or fuel container inside

i.

where there is an open flame, spark or pilot light
(e.g. furnace, water heater, space heater, clothes
dryer etc.).

Allow machine to cool at least 5 minutes before

j.

storing.

Never fill containers inside a vehicle or on a truck

k.

or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.

If possible, remove gas-powered equipment from

l.

the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a
trailer with a portable container, rather than from a
gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel

m.

tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.

Operation

Do not put hands or feet near rotating parts, in the auger/

1.
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.

The auger/impeller control lever is a safety device. Never

2.
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.

The control levers must operate easily in both directions

3.
and automatically return to the disengaged position when
released.

Never operate with a missing or damaged chute assembly.

4.
Keep all safety devices in place and working.

Never run an engine indoors or in a poorly ventilated area.

5.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.

Do not operate machine while under the influence of

6.
alcohol or drugs.

Muffler and engine become hot and can cause a burn. Do

7.
not touch. Keep children away.

Exercise extreme caution when operating on or crossing

8.
gravel surfaces. Stay alert for hidden hazards or traffic.

Exercise caution when changing direction and while

9.
operating on slopes.

Plan your snow-throwing pattern to avoid discharge

10.
towards windows, walls, cars etc. Thus, avoiding possible
property damage or personal injury caused by a ricochet.

Never direct discharge at children, bystanders and pets or

11.
allow anyone in front of the machine.

Do not overload machine capacity by attempting to clear

12.
snow at too fast of a rate.

Never operate this machine without good visibility or light.

13.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.

Disengage power to the auger/impeller when transporting

14.
or not in use.

Never operate machine at high transport speeds on

15.
slippery surfaces. Look down and behind and use care
when backing up.

If the machine should start to vibrate abnormally, stop

16.
the engine, disconnect the spark plug wire and ground it
against the engine. Inspect thoroughly for damage. Repair
any damage before starting and operating.

Disengage all control levers and stop engine before you

17.
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments,
or inspections.

Never put your hand in the discharge or collector

18.
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine and
remain behind handles until all moving parts have stopped
before unclogging.

Use only attachments and accessories approved by the

19.
manufacturer (e.g. wheel weights, tire chains, cabs etc.).

When starting engine, pull cord slowly until resistance

20.
is felt, then pull rapidly. Rapid retraction of starter cord
(kickback) will pull hand and arm toward engine faster than
you can let go. Broken bones, fractures, bruises or sprains
could result.

If situations occur which are not covered in this manual, use

21.
care and good judgment. Contact Customer Support for
assistance and the name of your nearest servicing dealer.

4 sectiOn 2 — iMpOrtant safe OperatiOn practices

Maintenance & Storage

Never tamper with safety devices. Check their proper

1.
operation regularly. Refer to the maintenance and
adjustment sections of this manual.

Before cleaning, repairing, or inspecting machine

2.
disengage all control levers and stop the engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting.

Check bolts and screws for proper tightness at frequent

3.
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.

Do not change the engine governor setting or over-speed

4.
the engine. The governor controls the maximum safe
operating speed of the engine.

Snow thrower shave plates and skid shoes are subject to

5.
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”

Check control levers periodically to verify they engage

6.
and disengage properly and adjust, if necessary. Refer
to the adjustment section in this operator’s manual for
instructions.

Maintain or replace safety and instruction labels, as

7.
necessary.

Observe proper disposal laws and regulations for gas, oil,

8.
etc. to protect the environment.

Prior to storing, run machine a few minutes to clear snow

9.
from machine and prevent freeze up of auger/impeller.

Never store the machine or fuel container inside where

10.
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.

Always refer to the operator’s manual for proper

11.
instructions on off-season storage.

Check fuel line, tank, cap, and fittings frequently for cracks

12.
or leaks. Replace if necessary.

Do not crank engine with spark plug removed.

13.

Do not modify engine

To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING: This machine is equipped with an

internal combustion engine and should not be used
on or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrester
meeting applicable local or state laws (if any).

If a spark arrester is used, it should be maintained in
effective working order by the operator. In the State of California
the above is required by law (Section 4442 of the California
Public Resources Code). Other states may have similar laws.
Federal laws apply on federal lands.
A spark arrester for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

Average Useful Life

According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or 60
hours of operation. At the end of the Average Useful Life, buy
a new machine or have the machine inspected annually by an
authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.

WARNING: Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

5sectiOn 2 — iMpOrtant safe OperatiOn practices

Assembly & Set-Up

Contents of Carton

One Snow Thrower• Two Replacement Auger Shear Pins• One Chute Assembly•

One Snow Thrower Operator’s

• One Tecumseh Engine Operator’s
Manual

Assembly

Handle

Observe the lower rear area of the snow thrower to be sure

1.
both cables are aligned with roller guides before pivoting
the handle upward. See Fig. 3-1.

NOTE: Make certain the upper ends of each cable are
seated properly in its bracket.

• One Product Registration Card•
Manual

3

Figure 3-1

Secure the handle by tightening the plastic knob located

2.
on both the left and right sides of the handle. Remove
and discard any rubber bands, if present. They are for
packaging purposes only.

Chute Assembly

1.

Position the chute assembly over the base. See Fig. 3-2.

2.

Close the flange keepers to secure the chute assembly
to the chute base. The flange keepers will click into place
when properly secure. See Fig. 3-3.

NOTE: If the flange keepers will not easily click into place,
use the palm of your hand to apply swift, firm pressure to
the back of each.

Figure 3-2

Figure 3-3

6

Chute Directional Control

A

B

Chute Clean-out Tool

Remove the plastic cap (if present), flat washer and hairpin

1.
clip from the end of the chute directional control. See Fig.
3-4.

Chute Directional Control

Remove the plastic cap (if present), flat washer and hairpin

1.
clip from the end of the chute directional control. See Fig.
3-4.

Figure 3-4

Insert the end of the chute directional control into the

2.
lower bracket and secure with the flat washer and hairpin
clip just removed. If necessary, the lower bracket can be
adjusted. Refer to Chute Bracket Adjustment on Page 16.

Set-Up

Shear Pins

A pair of replacement auger shear pins and bow tie cotter pins
are included with your snow thrower. See Fig. 3-5 Store them in a
safe place until needed.

Figure 3-6

Insert the end of the chute directional control into the

2.
lower bracket and secure with the flat washer and hairpin
clip just removed. If necessary, the lower bracket can be
adjusted. Refer to Chute Bracket Adjustment on Page 16.

Set-Up

Shear Pins

A pair of replacement auger shear pins and bow tie cotter pins
are included with your snow thrower. See Fig. 3-5 Store them in a
safe place until needed.

Chute Clean-Out Tool

The chute clean-out tool is fastened to the top of the auger
housing with a mounting clip and a cable tie at the factory. Cut
the cable tie before operating the snow thrower. See Fig. 3-6.

Tire Pressure

Before operating, check tire pressure and reduce pressure in
both tires to between 15 psi and 20 psi.

NOTE: If the tire pressure is not equal in both tires, the machine
may not travel in a straight path and the shave plate may wear
unevenly.

Figure 3-5

Gas & Oil Fill-Up

WARNING! Use extreme care when handling

gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel the machine
indoors or while the engine is hot or running.
Extinguish cigarettes, cigars, pipes and other
sources of ignition.

7sectiOn 3 — asseMbly & set-up

Adjustments

Skid Shoes

The snow thrower skid shoes are adjusted upward at the factory
for shipping purposes. Adjust them downward, if desired, prior
to operating the snow thrower.

CAUTION: It is not recommended that you operate

this snow thrower on gravel as it can easily pick up
and throw loose gravel, causing personal injury or
damage to the snow thrower and surrounding
property.

For close snow removal on a smooth surface, raise skid

•
shoes higher on the auger housing.

Use a middle or lower position when the area to be cleared

•
is uneven, such as a gravel driveway

NOTE: If you choose to operate the snow thrower on a gravel
surface, keep the skid shoes in position for maximum clearance
between the ground and the shave plate.

To adjust the skid shoes:

Loosen the four hex nuts (two on each side) and carriage

1.
bolts. Move skid shoes to desired position. See Fig. 3-7.

Chute Assembly

The distance snow is thrown can be adjusted by changing the
angle of the chute assembly. To do so:

Stop the engine by removing the ignition key and loosen

1.
the plastic knob found on the left side of the chute
assembly.

Pivot the chute upward or downward before retightening

2.
the wing knob. See Fig. 3-8.

Figure 3-7

Make certain the entire bottom surface of skid shoe is

2.
against the ground to avoid uneven wear on the skid
shoes.

Retighten nuts and bolts securely.

3.

Figure 3-8

8 sectiOn 3— asseMbly & set-up