Mtd GRASS CATCHER FOR LAWN TRACTORS Operator’s Manual

I09 FORM NO. 769-05342
MTD Products Aktiengesellschaft • Saarbrücken • Germany
1
D1
A1 A1
A1
A1
B1
2x C2
A2
O
A
D
C
B
E
F
H
I
K
J
A1
E1
A1
C1
F1
C1
B1
A1
A1
G1
H1
H1
L
E2
B2
4x D2
4x F2
G2
P
H1
H1
L1
H2
J2
2x K2
L2
M2
M
I2
J1
K1
I1
I1
I1
I1
N2
Q
D1
2
D1
5a
D2
8
11
14
2
E1
F1
C
D2
A2
E1
G1
3
A1
A1 B1
A1
C1
A1
6
F2
F2
F2
D2
D2
I
J
F2
C2
C
5b
9
12
B2
2.
15
C2
A1 A1
4
J1
7
10
F
13
1.
E
16
1
H1 H1
I1
K1
I1
L1
X
G2
E2
D
K
1
N2
H2
18
21
24
2.
1.
22
L2
M2
25
17 19
20
23
26
I2 J2
2
B
H
1
1.
2.
G
1.
2.
A
K2
1
K2
2
English
Français
Deutsch
4
6
8
EN
Installing the grass catcher
Before installing the grass catcher, park the lawn tractor on a level surface, apply the parking brake, switch the engine off and remove the spark-plug terminal.
Follow the safety instructions and operating instruction s in th e operating manual for the lawn tractor.
Check your model number so that you know which installation steps to perform. Identification of the model number:
You can find the rating plate under the driver’s seat. The fifth to seventh digits of the model number indicate the series. Example: Model number: 13AN773G600 = Series 700
Installation diagrams
The installation diagrams 1 to 26 are at the front (illustrated fold-out pages) of the manual.
Installing the holder “L” – Only required on units belonging to Series 700 Figs. 1-3
1. Fit a shoulder bolt (D1) and nut (E1) to each of the holders (F1) and (G1) – Fig. 2.
2. Remove the 4 screws (2 on left and 2 on right) from the rear side of the chassis and use these 4 screws (A1) subsequently for the side holder attachment (Fig. 3).
3. Now attach the pre-assembled holders (F1 and G1) from Step 1 to the tractor using the 8 screws (A1) (Fig. 3).
4. Insert the bolts (B1) into the two holders and secure each bolt with a cotter pin (C1) – Fig. 3.
Installing the mounting frame Figs. 1 and 4-7
1. Fit the two plates (L1 and K1) to the plate (J1) using 4 screws (H1) and 4 nuts (I1) – Fig. 4.
Note: Ensure that the plates are fitted correctly.
2. Now turn the pre-assembled mounting frame by 180° – see Fig. 5.
3. Fit the holder (C) to the pre-assembled mounting frame using 4 screws (D2) and 4 nuts (F2).
Note: Ensure that correct mounting holes are used in the side retaining plates and initially tighten the nuts only hand­tight, as this will facilitate the subsequent installation. Fig. 5a – for mounting on tractors belonging to the 700 Series. Fig. 5b – for mounting on all other tractors.
4. Now hook the pre-assembled mounting frame into the shoulder screws on the tractor frame/holder (Fig. 6).
Note: In the tractor series 700 first remove the retaining bolts (B1) and cotter pins (C1) from the holder (Fig. 3). Then re-attach them after hooking in the mounting frame to secure the mounting frame to the holder as well. Use mounting holes (X – Fig. 4) for installation.
5. Align the lower hole in the mounting frame with the hole in the hitching device on t he tractor chassis. Insert the bolt (E2)
through the mounting holes and secure the bolt with the cotter pin (G2) – Fig. 7.
6. Now tighten all bolts and nuts on the mounting frame.
Installing the grass catcher Figs. 1, 8-26
1. Push the support plate (I) into the recess on the grass catcher bag carrier (J) and secure the support plate on the grass
catcher carrier using a bolt (B2) and nut (C2) (Figs. 8 and 9).
2. Now hook the pre-assembled part into the mounting frame on the tractor between the 2 lugs and secure the part on the
mounting frame using a bolt (A2) and nut (C2) (Figs. 10 and 11).
3. Install the tube holder (F) by clicking it onto the tubular frame of the grass catcher bag carrier (Fig. 12).
Note: In Step 1 ensure that the edge of the tube holder is flush with the red line on the tubular frame.
4. Install the cover (E) in the hood (D):
1. Push the long end of the cover all the way into the recess of the hood (Fig. 13). Note: Ensure that the cover is situated under the guide (1) (Fig. 14).
2. Now press the other end of the cover into the designated recess (2) in the hood (Fig. 14).
5. Now position the hood on the mounting eyelets of the tubular frame (Fig. 15).
6. Attach the hood with the bolt (K). To do this, push the bolt (K) through the first mounting eyelet and then continue
through the second mounting eyelet until the end of the bolt touches the hood (Fig. 17). The bolt is now secured on the hood by the two lugs (Fig. 17). Note: To facilitate installation, use the inspection opening (1) in the hood (Fig. 16).
7. Open the hood (Fig. 18).
8. To do this, press your right hand onto the rear, right plate (Step 1) and grip the middle plate with your left hand to open
the hood upwards (Step 2) – Fig. 18.
4
9. Hook both grass catcher bags (G) into the tube holder, ensuring that the more impervious side (closer meshed fabric) is
at the front (Fig. 19). Note: First hook in the front side and then lower the rear side until the grass catcher bag is situated firmly in the tubular frame.
10. Fit the rubber mount (N2) to the mower deck connector (B) using the bolt (H2), washer (I2) and safety cotter pin (J2) –
Fig. 20.
11. Fit the retaining bolt (L2) and nut (M2) to the mower deck (Fig. 21).
12. Installing the mowed deck connector: (Figs. 22 – 24):
1. Open the impact guard on the mower deck and hold it firmly in this position (Fig. 22).
2. Place the rear upper edge of the mower deck connector over the rear upper edge of the mower deck opening. Now swivel the connector down over the mower deck opening (Fig. 22). Note: The connector is correctly installed when the lower edge is situated over the lower edge of the mower deck opening (Fig. 23). Ensure that the installation is correct.
13. Hook the rubber mount into the retaining bolt on the mower deck to secure the mower deck connector on the mower deck (Fig. 24).
14. Align the guide grooves (1) on the intermediate piece (A) with the mounting lugs (2) on the mo wer deck connector and push the intermediate piece all the way onto the mo wer deck connector (Fig. 25).
15. Secure the intermediate piece on the mower deck connector using the retaining clips (K2) (F ig. 25).
16. Open the hood and push the pipe end section (H) onto the intermediate piece and align it until the lower retaining groove (1) is situated firmly in the tube holder (2) (Fig. 26). Note: Ensure that the installation is secure and correct.
17. Close the hood on the grass catcher.
18. Inspect the installation and perform a function test.
Operating the grass catcher:
Emptying
Switch off the unit.
Apply parking brake.
Open grass catcher hood and lift up.
Take hold of the grass catcher baskets by the grip points at the bottom of the grass catcher bags and then take out of
the holders.
Empty grass catcher bags.
Hook in grass catcher bags and close the grass catcher hood again.
Additional information:
accessories / or included in product package depending on model) should be installed (tightening torque of the blade screw 122 Nm). If required, contact your local dealer.
To ensure that the grass catcher functions optimally, the “Highlift blades” (optional
5
Loading...