MTD 769-04165 User Manual
Safety • Assembly • Operation • Adjustments • Maintenance • Troubleshooting • Parts Lists •
OPERATOR’S MANUAL
Two-Stage Snow Thrower
IMPORTANT:
READ SAFETY RULES AND INSTRUCTIONS
CAREFULLY BEFORE OPERATING EQUIPMENT.
PRINTED IN U.S.A.
MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1
769-04165
06/17/08
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,
-4$02/$5#43,)-)4%$
+)4#(%.%2/..'*
8888888888
88888888888
-ODEL.UMBER
.UM£RODEMODÞLE
3ERIAL.UMBER
.UM£RODES£RIE
WWWMTDCANADACOM
prepare and maintain the unit for best performance. Please read and understand what it says.
Table of Contents
Safety Symbols .................................................. 3
Safe Operation Practices ................................... 4
Setting Up Your Snow Thrower ..........................6
Know Your Snow Thrower ..................................8
Operating Your Snow Thrower ...........................9
Finding and Recording Model Number
BEFORE YOU START ASSEMBLING
YOUR NEW EQUIPMENT,
please locate the model plate on the equipment and copy the
model number and the serial number to the sample model
plate provided to the right. You can locate the model plate by
standing at the operating position and looking down at the
frame.
Adjustments & Maintenance ...........................12
Off-Season Storage .......................................... 14
Trouble Shooting .............................................. 15
Illustrated Parts Lists ....................................... 16
Warranty ............................................................ 20
Customer Support
Please do
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,
you can seek help from the experts. Choose from the options below:
1. Visit www.mtdcanada.ca for many useful suggestions, click on Customer Support button.
2. Call a Customer Support Representative at 1-800-668-1238.
3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,
warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed
separately with this product.
Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.
You will be asked to enter the serial number in order to process your call.
NOT
return the unit to the retailer from which it was purchased,
without rst contacting Customer Support.
2
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before
attempting to assemble and operate.
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running.
There are rotating blades inside.
WARNING— ROTATING BLADES
Keep hands out of inlet and discharge openings while machine is running.
There are rotating blades inside.
WARNING— ROTATING AUGER
Do not put hands or feet near rotating parts, in the auger/impeller housing
or chute assembly. Contact with the rotating parts can amputate hands and
feet.
WARNING—THROWN OBJECTS
This machine may pick up and throw and objects which can cause serious
personal injury.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust
contains carbon monoxide, an odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain.
1
Safety
Symbols
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the personal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
3
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions which,
if not followed, could
endanger the personal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol,
ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
HEED
DANGER: This machine was built to be operated according to the safe operation practices in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the instructions and safe operation practices
in this manual and on the machine and be trained and
supervised by an adult.
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
Preparation
Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards, wires
and other foreign objects, which could be tripped over or
thrown by the auger/impeller.
1. Always wear safety glasses or eye shields during
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
2. Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose
clothing, which could become entangled in moving parts.
Wear footwear which will improve footing on slippery
surfaces.
3. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
4. Adjust collector housing height to clear gravel or crushed
rock surfaces.
5. Disengage all control levers before starting the engine.
6. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
7. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
Safe Handling of Gasoline
To avoid personal injury or property damage use extreme care
in handling gasoline. Gasoline is extremely flammable and the
vapors are explosive. Serious personal injury can occur when
gasoline is spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
e. Allow engine to cool at least two minutes before refuel-
ing.
f. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide space for fuel
expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait 5 minutes
before starting the engine.
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least 5 minutes before storing
k. Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
l. If possible, remove gas-powered equipment from the
truck or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dispenser
nozzle.
m. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
4
Operation
1. Do not put hands or feet near rotating parts, in the auger/
impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets or
allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
14. Disengage power to the auger/impeller when transporting or
not in use.
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the discharge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. When starting engine, pull cord slowly until resistance is felt,
then pull rapidly. Rapid retraction of starter cord (kickback)
will pull hand and arm toward engine faster than you can let
go. Broken bones, fractures, bruises or sprains could result.
21. If situations occur which are not covered in this manual, use
care and good judgment. Call customer assistance for the
name of your nearest servicing dealer.
Maintenance & Storage
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjustment sections of this manual.
2. Before cleaning, repairing, or inspecting machine disengage
all control levers and stop the engine. Wait until the auger/
impeller come to a complete stop. Disconnect the spark plug
wire and ground against the engine to prevent unintended
starting.
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as necessary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
12. Check fuel line, tank, cap, and fittings frequently for cracks
or leaks. Replace if necessary.
13. Do not crank engine with spark plug removed.
Do not modify engine
To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modification (EM) Oxidizing Catalyst (OC), Secondary Air Injection (SAI)
and Three Way Catalyst (TWC) if so equipped.
Average Useful Life
According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or
60 hours of operation. At the end of the Average Useful Life,
have the machine inspected annually by an authorized service
dealer to ensure that all mechanical and safety systems are
working properly and not worn excessively. Failure to do so can
result in accidents, injuries or death.
05.08.08
2
Safe
Operation
Practices
WARNING
This symbol points
out important safety
instructions, which
if not followed, could
endanger the personal safety and/or
property of yourself
and others. Read and
follow all instructions
in this manual before
attempting to operate
this machine. Failure
to comply with these
instructions may
result in personal
injury. When you see
this symbol, HEED
IT’S WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
5
3
Setup And
Adjustment
IMPORTANT: This unit is shipped WITH OIL and
WITHOUT GASOLINE. After assembly refer to
separate engine manual for proper fuel and engine oil
recommendations.
NOTE: Reference to right hand or left hand side of
machine are observed from the operating position.
NOTE: This Operator’s Manual covers several
models. Snow thrower features vary by model. Not all
features discussed in this manual are applicable to all
snow thrower models.
Setting Up The Handle
Chute Handle
WARNING
Always stop engine,
disconnect spark
plug, and ground
against engine before
cleaning, lubricating
or doing any kind
of maintenance or
adjustments on your
machine.
DO NOT LIFT
MACHINE WITH
CHUTE HANDLE.
NOTE: Never replace
the auger shear pins
with standard pins.
Any damage to the
auger gearbox or other
components, as a reult
of doing so, will NOT
be covered by your
snow thrower’s warranty.
NOTE: Be aware of the three loosely fitted cable ties
attached to the lower handle that will be ustilizred later
to secure the cables.
WARNING: Do not lift the snow thrower by the chute
handle. See Figure 1.
1. Loosen and remove the wing knob, saddle washer,
handle tab and carriage bolt on each side of the
lower handle. See Figure 2.
2. Slide one of the loosely fitted cable ties from the right
side of the lower handle up to the cross member
of the lower handle. Leave the second cable tie
in place on the right side of the lower handle. See
Figure 4. for reference.
3. Lift the upper handle up and position it over the lower
handle, aligning the holes where the wing knobs
were removed. See Figure 3.
CAUTION : Be careful not to bend or kink the cable.
4. Insert the carriage bolt from the outside through a
handle tab, the upper and lower handles, a saddle
washer and into the wing knob . Repeat on the other
side.
5. Tighten the wing knobs on each side of the handle.
See Figure 3.
NOTE: Make sure that the drive cable is routed parallel
to the left upper handle, then across the top of the lower
handle and finally parallel to the right lower handle. See
Figure 4.
6. Three cable ties have been used to loosely tie the
two control cables to the lower handle. Two of these
cable ties are on each arm, and third on the top
cross bar of the lower handle. Tighten these cable
ties to secure the cable to the lower handle. See
Figure 4.
Figure 1
Figure 2
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing..
Clean-Out Tool
This tool and the electric extension cord, if so equipped,
may be fastened with a cable tie to the rear of the auger
housing for shipping purposes. In that case, cut the
cable tie and remove the extension cord now.
Figure 3
6
High Position
Middle Position
Low Position
Tire Pressure
The proper inflation pressure is 20 psi. Check the tire
pressure periodically and maintain equal pressure in both
tires at all times. Excessive pressure (well above 20 psi)
may cause the wheel (tire/rim) assembly to burst with
sufficient force to cause serious injury. Do not over-inflate
the tire. Use a manual pump or portable electric tire
inflator to prevent over-inflation. NEVER USE AN AIR
COMPRESSOR.
3
Setting Up
Your Snow
Drive Cable
Figure 4
Cable Ties
Figure 5
Auger Cable
Skid Shoe
The space between the shave plate and the ground
can be adjusted. See Figure 7. For close snow removal,
place skid shoes in the low position. When the area to
be cleared is uneven, place skid shoes in the middle or
high position. See Figure 4.
1. Adjust skid shoes by loosening two hex nuts and
carriage bolts on each skid shoe, and moving the
skid shoe to the desired position. See Figure 4.
2. Make certain the entire bottom surface of skid shoe
is against the ground to avoid uneven wear on the
skid shoes.
3. Tighten nuts and bolts securely.
Routing The Drive Cable
1. Make sure that the drive cable is routed parallel to
the left upper handle, then across the top of the
lower handle and finally parallel to the right lower
handle. See Figure 5.
2. Three cable ties have been used to loosely tie the
two control cables to the lower handle. Two of these
cable ties are on each arm, and third on the top
cross bar of the lower handle. Tighten these cable
ties to secure the cable to the lower handle. See
Figure 5.
Auger Cable
Periodic adjustment to the auger control cable may be
required due to normal stretch and wear on the belt.
Adjustment is needed if the augers seem to hesitate
while turning, but the engine maintains speed, or
continue turning with the auger control disengaged.
1. Loosen the rear hex bolt on the cable adjustment
bracket. See Figure 6.
2. Slide the cable adjustment bracket backwards
taking out the slack in the auger cable.
3. Retighten the rear hex bolt
4. Start engine and verify auger control engages and
disengages properly.
Thrower
WARNING
Do not over-tighten
the cable. Overtightening may
prevent the auger
from disengaging
and compromise the
safety of the snow
thrower.
If auger continues
to rotate with the
control disengaged,
shut off engine and
readjust.
Never attempt to
clean chute or make
any adjustment while
engine is running.
Over-inflating the
tire with excessive
pressure (well above
20 psi) may cause
the tire/rim to burst
with sufficient force
to cause serious
pressure.
Figure 6
7
4
Models with Ergo handle
Chute Assembly
Clean-out Tool
Auger
Shave Plate
Fuel Cap
Starter Rope
Skid Shoe
Chute Handle
Auger Control
Auger Control
Upper Handle
Drive Control
Drive Control
Fuel Cap
Muffler
Oil Cap
Oil Drain
Recoil Starter
Handle
Primer
Ignition
Key
Throttle
Contro l
Choke
Know
Your Snow
Thrower
WARNING
Be familiar with
all the controls on
the snow thrower
and their proper
operation. Know how
to stop the machine
and disengage them
quickly.
Never make adjustments to the chute
assembly unless
both controls are
disengaged and the
operator is standing
beside the unit.
Figure 7
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine and also stops the engine.
Drive Control
Located on the underside of the upper handle, the drive
control is used to engage/disengage wheels. Pull the
drive control against the upper handle to engage the
wheels; release to disengage.
Auger Control
Located on the top side of the upper handle, the auger
control is used to engage and disengage the augers.
Pull the auger control back against the upper handle to
engage the augers; release to disengage.
IMPORTANT: Refer to Auger Control Test on page 10
prior to operating your snow thrower. Read and follow
all instructions carefully and perform all adjustments
to verify your snow thrower is operating safely and
properly.
Discharge Chute
The direction snow is thrown can be changed by turning
the lower chute with the chute handle. The distance
snow is thrown can be adjusted by raising the upper
chute for greater distance, or lowering for less distance.
Loosen the wing nut on the side of the discharge chute
to adjust. Pivot the chute to desired position, and
retighten wing nut.
Ignition Key
The ignition key is a safety device. Insert key and snap in
place; do not turn ignition key. Pull the key out halfway to
stop the engine. Remove key when the unit is not in use.
Shave Plate
The shave plate maintains contact with pavement as
the snow thrower is propelled, allowing snow close to
pavement’s surface to be discharged.
Skid Shoe
The space between the shave plate and the ground can
be adjusted. For close snow removal, place skid shoes in
the low position. Use middle or high position when area to
be cleared is uneven or on gravel surfaces.
Engine Operating Controls
Refer to the separate engine manual for engine operating
controls and their functions.
8
Gas and Oil Fill-up
• Servicetheenginewithgasolineandoilasinstructed
in the separate engine manual packed with your
snowthrower. Read instructions carefully.
WARNING: Never fill fuel tank indoors.
Never fill fuel tank with engine running
or while engine is hot. Do not smoke
when filling fuel tank.
• Makecertaintheaugeranddrivecontrolbailsarein
the disengaged (released) position.
Starting the Engine
WARNING: Always keep hands and
feet clear of moving parts. Do not use
a pressurized starting fluid. Vapors are
flammable.
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until
it reaches operating temperatures.
Engines with Starter Handle (non-electric
start)
IMPORTANT: Do not pull the starter handle with engine
running.
Insert ignition key fully into slot. Make sure it snaps 1.
into place. DO NOT turn ignition key. The engine
cannot start unless the key is inserted into ignition
switch.
Move throttle control to FAST (rabbit) position.2.
Move choke to the ON position (cold engine start). If 3.
engine is warm, place choke in OFF position.
Push primer three to five (3-5) times, making sure 4.
to cover vent hole when pushing. If engine is warm,
push primer only once. Always cover vent hole when
pushing. Cool weather may require priming to be
repeated.
Pull gently on the starter handle until it begins to 5.
resist, then pull quickly and forcefully to overcome
the compression. Do not release the handle and allow it to snap back. Return rope SLOWLY to original
position. If required, repeat this step.
As the engine warms, slowly rotate the choke control 6.
to OFF position. If the engine falters, restart engine
and run with choke at half-choke position for a short
period of time, and then slowly rotate the choke into
OFF position.
Engines with Electric Starters
WARNING: The electric starter is
equipped with a grounded three-wire
power cord and plug, and is designed
to operate on 120 volt AC household
current. It must be used with a properly grounded three-prong receptacle
at all times to avoid the possibility of
electric shock. Follow all instructions
carefully prior to operating the electric
starter.
WARNING: DO NOT use electric starter
in rain.
Determine that your home’s wiring is a three-wire 1.
grounded system. Ask a licensed electrician if you
are unsure. If you have a grounded three-prong
receptacle, proceed as follows. If you do not have
the proper house wiring, DO NOT use the electric
starter under any conditions.
Insert ignition key fully into slot. Make sure it snaps 2.
into place. DO NOT turn ignition key. The engine
cannot start unless the key is inserted into
ignition switch.
Plug the extension cord into the electric switch box 3.
located on the engine. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC
outlet in a well-ventilated area.
Move throttle control to FAST (rabbit) position.4.
Move choke to the ON position (cold engine start). 5.
If engine is warm, place choke in OFF position.
Push primer three to five (3-5) times, making sure 6.
to cover vent hole when pushing. If engine is warm,
push primer only once. Always cover vent hole
when pushing. Cool weather may require priming
to be repeated.
Push starter button to start engine. 7. Once the
engine starts, immediately release starter button.
Electric starter is equipped with thermal overload
protection; system will temporarily shut-down to
allow starter to cool if electric starter becomes
overloaded.
As the engine warms, slowly rotate the choke 8.
control to OFF position. If the engine falters, restart
engine and run with choke at half-choke position
for a short period of time, and then slowly rotate the
choke into OFF position.
After engine is running, disconnect power cord 9.
from electric starter. When disconnecting, always
unplug the end at the wall outlet before unplugging
the opposite end from the engine.
5
Operation
WARNING
Read, understand,
and follow all instructions and warnings
on the machine and
in this manual before
operating.
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
If your home’s wiring system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
If your home
electrical system
is grounded, but a
three-hole receptacle
is not available, do
not use your snow
thrower’s electric
starter.
9
5
Operation
WARNING
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or
while performing
any adjustments or
repairs on it.
Be sure no one other
than the operator is
standing near the
snow thrower while
starting engine or
operating snow
thrower. Never run
engine indoors or in
enclosed, poorly ventilated areas. Engine
exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands,
feet, hair and loose
clothing away from
any moving parts
on engine and snow
thrower.
Stopping the Engine
WARNING: To avoid unsupervised
engine operation, never leave the
engine unattended while running. Turn
the engine off after use and remove
ignition key
Run engine for a few minutes before stopping to help
dry off any moisture on the engine.
Move throttle control to STOP position.1.
Remove the ignition key. Removing the key will 2.
reduce the possibility of unauthorized starting of
the engine while equipment is not in use. Keep
the key in a safe place. The engine cannot start
without the ignition key.
Wipe all snow and moisture from the area around 3.
the engine as well as the area in and around the
drive control and auger control. Also, engage and
release both controls several times.
Auger Control Test
IMPORTANT: Perform the following test before operating the snow thrower for the first time and at the start of
each season.
Check the adjustment of the auger control as follows:
1. When the auger control is released and in the
disengaged “up” position, the cable should have very
little slack, but should NOT be tight.
2. In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting Engine. Make sure the throttle is set
in the FAST position.
3. While standing in the operator’s position (behind the
snow thrower) engage the auger.
4. Allow the auger to remain engaged for approximately
ten (10) seconds before releasing the auger control.
Repeat this several times.
5. With the engine running in the FAST position and the
auger control in the disengaged “up” position, walk to
the front of the machine.
6. Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for all moving parts to stop before
readjusting the auger control cable as shown in the
“Setup And Adjustment” section on page 7.
Operating The Snowthrower
NOTE: Allow the engine to warm up for a few minutes
as the engine will not develop full power until it reaches
operating temperature.
• Adjustthedischargechuteasdesired.Donotthrow
snow toward a building as hidden objects could be
discharged with enough force to cause damage.
• Starttheengineasinstructedpreviously.
• Makingcertainnobystandersorobstaclesareinfront
of the unit, squeeze the auger control bail completely
against the upper handle to fully engage the augers.
Release the auger control bail and the augers will
stop.
• Whiletheaugercontrolhandleisengaged,squeeze
the drive control bail completely against the upper
handle to engage the wheels. Release the drive
control bail and the wheels will stop.
• Asthesnowthrowerstartstomove,maintainafirm
hold on the handle, and guide the snowthrower along
the path to be cleared.
• Release the bails to stop the snowthrowing action and
forward motion.
NOTE: Your unit is equipped with a clutch in the transmission. If the wheels stop turning while trying to discharge
large volumes of snow, immediately disengage the drive
control bail and allow the rotating augers to discharge
snow from the housing. Continue operation reducing
clearing width.
10
Operating Tips
• Formostefficientsnowremoval,removesnow
immediately after it falls.
• Dischargesnowdownwindwheneverpossible.Slightly
overlap each previous swath.
• Settheslideshoes1/4”belowtheshaveplatefor
normal usage. The slide shoes may be adjusted to low
position, see Figure for hard-packed snow.
NOTE: It is not recommended that you operate
this snowthrower on gravel as loose gravel can be
easily picked up and thrown by the auger causing
personal injury, property damage and/or damage to your
snowthrower.
• Ifforsomereason,youhavetooperatethe
snowthrower on gravel, keep the slide shoe in the
highest position for maximum clearance between the
ground and the shave plate.
• Becertaintofollowtheprecautionslistedunder“To
Stop Engine” to prevent possible freeze-up.
• Cleanthesnowthrowerthoroughlyaftereachuse.
Clean-Out Tool
WARNING: Never use your hands to
clear a clogged chute assembly. Shut
off engine and remain behind handles
until all moving parts have stopped
before unclogging.
• Releaseboththeaugercontrolandthedrive/auger
control lock.
• Stoptheengine.
• Removetheclean-outtoolfromthemountingclip.
• Usetheshovel-shapedendoftheclean-outtoolto
remove any snow and ice in the chute assembly.
• Re-fastentheclean-outtooltothemountingclipon
the rear of the auger housing and restart engine.
• Whilestandingintheoperator’sposition(behindthe
snow thrower), engage the auger control for a few
seconds to clear any remaining snow or ice from the
chute assembly before continuing to clear snow.
5
Operation
WARNING
Never use your
hands to clean
snow and ice
from the chute
assembly or
auger housing.
The temperature of
muffler and the surrounding areas may
exceed 150° F. Avoid
these areas
11
Loading...