MTD 760, 770 User Manual

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

OperatOr’s Manual

Model Series 760-770 Lawn Tractor

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

Printed In USA

Form No. 769-03436

(October 8, 2007)

To The Owner

Thank You

Thank you for purchasing a lawn tractor manufactured by
MTD LLC. It was carefully engineered to provide excellent
performance when properly operated and maintained.

Please read this entire manual prior to operating the equipment.
It instructs you how to safely and easily set up, operate and
maintain your machine. Please be sure that you, and any other
persons who will operate the machine, carefully follow the
recommended safety practices at all times. Failure to do so could
result in personal injury or property damage.

All information in this manual is relative to the most recent
product information available at the time of printing. Review
this manual frequently to familiarize yourself with the machine,
its features and operation. Please be aware that this Operator’s
Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated
in this manual may not be applicable to all models. MTD LLC
reserves the right to change product specifications, designs and
equipment without notice and without incurring obligation.

Table of Contents

Safe Operation Practices ........................................ 3

Assembly & Set-Up .................................................. 8

Controls & Features ................................................12

Operation ................................................................15

Maintenance & Adjustment .................................19

Service .................................................................... 23

1

This product has met the rigid safety standards of the Outdoor
Power Equipment Institute and an independent testing
laboratory. If you have any problems or questions concerning
the machine, phone your local authorized MTD service dealer
or contact us directly. MTD’s Customer Support telephone
numbers, website address and mailing address can be found on
this page. We want to ensure your complete satisfaction at all
times.

Throughout this manual, all references to right and left side of the
machine are observed from the operating position

The engine manufacturer is responsible for all engine-related
issues with regards to performance, power-rating, specifications,
warranty and service. Please refer to the engine manufacturer’s
Owner’s/Operator’s Manual, packed separately with your
machine, for more information.

Troubleshooting .................................................... 28

Replacement Parts ................................................ 29

Attachments & Accessories .................................. 30

CA. Emission Control Statement ...........................31

Warranty ................................................................ 32

Spanish ................................................................... 33

Record Product Information

Before setting up and operating your new equipment, please
locate the model plate on the equipment and record the
information in the provided area to the right. You can locate the
model plate by looking beneath the seat. This information will
be necessary, should you seek technical support via our web
site, Customer Support Department, or with a local authorized
service dealer.

MOdel nuMber

serial nuMber

Customer Support

Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of
this machine, you can seek help from the experts. Choose from the options below:

Visit us on the web at www.mtdproducts.com

◊

Call a Customer Support Representative at [phone] or [phone]

◊

Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019

◊

2

Important Safe Operation Practices

WARNING: This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow
all instructions in this manual before attempting to operate this machine. Failure to comply
with these instructions may result in personal injury.
When you see this symbol. HEED ITS WARNING!

CALIFORNIA PROPOSITION 65

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects
or other reproductive harm.

WARNING: Battery posts, terminals, and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and reproductive
harm. Wash hands after handling

DANGER: This machine was built to be operated according to the safe operation practices in
this manual. As with any type of power equipment, carelessness or error on the part of the
operator can result in serious injury. This machine is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety instructions could result in
serious injury or death.

2

General Operation

Read, understand, and follow all instructions on the

1.
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.

Be familiar with all controls and their proper operation.

2.
Know how to stop the machine and disengage them
quickly.

Never allow children under 14 years of age to operate this

3.
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.

Never allow adults to operate this machine without proper

4.
instruction.

To help avoid blade contact or a thrown object injury,

5.
keep bystanders, helpers, children and pets at least 75 feet
from the machine while it is in operation. Stop machine if
anyone enters the area.

Thoroughly inspect the area where the equipment is to be

6.
used. Remove all stones, sticks, wire, bones, toys, and other
foreign objects which could be picked up and thrown by
the blade(s). Thrown objects can cause serious personal
injury.

Plan your mowing pattern to avoid discharge of material

7.
toward roads, sidewalks, bystanders and the like. Also,
avoid discharging material against a wall or obstruction
which may cause discharged material to ricochet back
toward the operator.

Always wear safety glasses or safety goggles during

8.
operation and while performing an adjustment or repair
to protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.

Wear sturdy, rough-soled work shoes and close-fitting

9.
slacks and shirts. Loose fitting clothes and jewelry can be
caught in movable parts. Never operate this machine in
bare feet or sandals.

Be aware of the mower and attachment discharge direction

10.
and do not point it at anyone. Do not operate the mower
without the discharge cover or entire grass catcher in its
proper place.

Do not put hands or feet near rotating parts or under the

11.
cutting deck. Contact with the blade(s) can amputate
hands and feet.

3

A missing or damaged discharge cover can cause blade

12.
contact or thrown object injuries.

Stop the blade(s) when crossing gravel drives, walks, or

13.
roads and while not cutting grass.

Watch for traffic when operating near or crossing

14.
roadways. This machine is not intended for use on any
public roadway.

Do not operate the machine while under the influence of

15.
alcohol or drugs.

Mow only in daylight or good artificial light.

16.
Never carry passengers.

17.
Disengage blade(s) before shifting into reverse. Back up

18.
slowly. Always look down and behind before and while
backing to avoid a back-over accident.

Slow down before turning. Operate the machine smoothly.

19.
Avoid erratic operation and excessive speed.

Disengage blade(s), set parking brake, stop engine and

20.
wait until the blade(s) come to a complete stop before
removing grass catcher, emptying grass, unclogging chute,
removing any grass or debris, or making any adjustments.

Never leave a running machine unattended. Always turn

21.
off blade(s), place transmission in neutral, set parking
brake, stop engine and remove key before dismounting.

Use extra care when loading or unloading the machine into

22.
a trailer or truck. This machine should not be driven up or
down ramp(s), because the machine could tip over, causing
serious personal injury. The machine must be pushed
manually on ramp(s) to load or unload properly.

Muffler and engine become hot and can cause a burn. Do

23.
not touch.

Check overhead clearances carefully before driving under

24.
low hanging tree branches, wires, door openings etc.,
where the operator may be struck or pulled from the
machine, which could result in serious injury.

Disengage all attachment clutches, depress the brake

25.
pedal completely and shift into neutral before attempting
to start engine.

Your machine is designed to cut normal residential grass of

26.
a height no more than 10”. Do not attempt to mow through
unusually tall, dry grass (e.g., pasture) or piles of dry leaves.
Dry grass or leaves may contact the engine exhaust and/or
build up on the mower deck presenting a potential fire
hazard.

Use only accessories and attachments approved for this

27.
machine by the machine manufacturer. Read, understand
and follow all instructions provided with the approved
accessory or attachment.

Data indicates that operators, age 60 years and above, are

28.
involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability
to operate the riding mower safely enough to protect
themselves and others from serious injury.

If situations occur which are not covered in this manual, use

29.
care and good judgment. Contact your customer service
representative for assistance.

Slope Operation

Slopes are a major factor related to loss of control and tip-over
accidents which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.

For your safety, use the slope gauge included as part of this
manual to measure slopes before operating this machine on
a sloped or hilly area. If the slope is greater than 15 degrees as
shown on the slope gauge, do not operate this machine on that
area or serious injury could result.

Do:

Mow up and down slopes, not across. Exercise extreme

1.
caution when changing direction on slopes.

Watch for holes, ruts, bumps, rocks, or other hidden

2.
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.

Use slow speed. Choose a low enough speed setting so

3.
that you will not have to stop or shift while on the slope.
Tires may lose traction on slopes even though the brakes
are functioning properly. Always keep machine in gear
when going down slopes to take advantage of engine
braking action.

Follow the manufacturer’s recommendations for wheel

4.
weights or counterweights to improve stability.

Use extra care with grass catchers or other attachments.

5.
These can change the stability of the machine.

Keep all movement on the slopes slow and gradual. Do

6.
not make sudden changes in speed or direction. Rapid
engagement or braking could cause the front of the
machine to lift and rapidly flip over backwards which could
cause serious injury.

Avoid starting or stopping on a slope. If tires lose traction,

7.
disengage the blade(s) and proceed slowly straight down
the slope.

Do Not:

Do not turn on slopes unless necessary; then, turn slowly

1.
and gradually downhill, if possible.

Do not mow near drop-offs, ditches or embankments. The

2.
mower could suddenly turn over if a wheel is over the edge
of a cliff, ditch, or if an edge caves in.

Do not try to stabilize the machine by putting your foot on

3.
the ground.

Do not use a grass catcher on steep slopes.

4.
Do not mow on wet grass. Reduced traction could cause

5.
sliding.

Do not shift to neutral and coast downhill. Over-speeding

6.
may cause the operator to lose control of the machine
resulting in serious injury or death.

Do not tow heavy pull behind attachments (e.g. loaded

7.
dump cart, lawn roller, etc.) on slopes greater than 5
degrees. When going down hill, the extra weight tends to
push the tractor and may cause you to loose control (e.g.
tractor may speed up, braking and steering ability are
reduced, attachment may jack-knife and cause tractor to
overturn).

4 sectiOn 2 — iMpOrtant safe OperatiOn practices

Children

Tragic accidents can occur if the operator is not alert to the

1.
presence of children. Children are often attracted to the
machine and the mowing activity. They do not understand
the dangers. Never assume that children will remain where
you last saw them.

Keep children out of the mowing area and in

a.

watchful care of a responsible adult other than the
operator.

Be alert and turn machine off if a child enters the

b.

area.
Before and while backing, look behind and down for

c.

small children.
Never carry children, even with the blade(s) shut off.

d.

They may fall off and be seriously injured or interfere
with safe machine operation.

Use extreme care when approaching blind corners,

e.

doorways, shrubs, trees or other objects that may
block your vision of a child who may run into the
path of the machine.

To avoid back-over accidents, always disengage

f.

the cutting blade(s) before shifting into Reverse.
If equipped, the “Reverse Caution Mode” should
not be used when children or others are around.

Keep children away from hot or running engines.

g.

They can suffer burns from a hot muffler.
Remove key when machine is unattended to

h.

prevent unauthorized operation.

Never allow children under 14 years of age to operate this

2.
machine. Children 14 and over should read and understand
the instructions and safe operation practices in this manual
and on the machine and should be trained and supervised
by an adult.

Towing

Tow only with a machine that has a hitch designed for

1.
towing. Do not attach towed equipment except at the
hitch point.

Follow the manufacturers recommendation for weight

2.
limits for towed equipment and towing on slopes.

Never allow children or others in or on towed equipment.

3.
On slopes, the weight of the towed equipment may cause

4.
loss of traction and loss of control.

Travel slowly and allow extra distance to stop.

5.
Do not shift to neutral and coast downhill.

6.

Service

Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme

1.
care in handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Serious
personal injury can occur when gasoline is spilled on
yourself or your clothes which can ignite. Wash your skin
and change clothes immediately.

Use only an approved gasoline container.

a.

Never fill containers inside a vehicle or on a truck

b.

or trailer bed with a plastic liner. Always place
containers on the ground away from your vehicle
before filling.

When practical, remove gas-powered equipment

c.

from the truck or trailer and refuel it on the ground.
If this is not possible, then refuel such equipment on
a trailer with a portable container, rather than from a
gasoline dispenser nozzle.

Keep the nozzle in contact with the rim of the fuel

d.

tank or container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.

Extinguish all cigarettes, cigars, pipes and other

e.

sources of ignition.
Never fuel machine indoors.

f.

Never remove gas cap or add fuel while the engine

g.

is hot or running. Allow engine to cool at least two
minutes before refueling.

Never over fill fuel tank. Fill tank to no more than ½

h.

inch below bottom of filler neck to allow space for
fuel expansion.

Replace gasoline cap and tighten securely.

i.

If gasoline is spilled, wipe it off the engine and

j.

equipment. Move machine to another area. Wait 5
minutes before starting the engine.

To reduce fire hazards, keep machine free of grass,

k.

leaves, or other debris build-up. Clean up oil or fuel
spillage and remove any fuel soaked debris.

Never store the machine or fuel container inside

l.

where there is an open flame, spark or pilot light
as on a water heater, space heater, furnace, clothes
dryer or other gas appliances.

Allow a machine to cool at least five minutes before

m.

storing.

General Service

Never run an engine indoors or in a poorly ventilated area.

1.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.

Before cleaning, repairing, or inspecting, make certain the

2.
blade(s) and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.

Periodically check to make sure the blades come to

3.
complete stop within approximately (5) five seconds after
operating the blade disengagement control. If the blades
do not stop within the this time frame, your machine
should be serviced professionally by an authorized MTD
Service Dealer.

Check brake operation frequently as it is subjected to wear

4.
during normal operation. Adjust and service as required.

5sectiOn 2 — iMpOrtant safe OperatiOn practices

5.

Check the blade(s) and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade(s)
for damage (e.g., excessive wear, bent, cracked). Replace
the blade(s) with the original equipment manufacturer’s
(O.E.M.) blade(s) only, listed in this manual. “Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!”

6.

Mower blades are sharp. Wrap the blade or wear gloves,
and use extra caution when servicing them.

7.

Keep all nuts, bolts, and screws tight to be sure the
equipment is in safe working condition.

8.

Never tamper with the safety interlock system or other
safety devices. Check their proper operation regularly.

9.

After striking a foreign object, stop the engine, disconnect
the spark plug wire(s) and ground against the engine.
Thoroughly inspect the machine for any damage. Repair
the damage before starting and operating.

10.

Never attempt to make adjustments or repairs to the
machine while the engine is running.

11.

Grass catcher components and the discharge cover are
subject to wear and damage which could expose moving
parts or allow objects to be thrown. For safety protection,
frequently check components and replace immediately
with original equipment manufacturer’s (O.E.M.) parts only,
listed in this manual. “Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!”

12.

Do not change the engine governor settings or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.

13.

Maintain or replace safety and instruction labels, as
necessary.

14.

Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.

Notice Regarding Emissions

Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and
may include the following emission control systems: Engine
Modification (EM) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING: This machine is equipped with an

internal combustion engine and should not be used
on or near any unimproved forest-covered,
brushcovered or grass-covered land unless the
engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if
any).

If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the
above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws
apply on federal lands.
A spark arrester for the muffler is available through your
nearest engine authorized service dealer or contact the service
department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

Average Useful Life

According to the Consumer Products Safety Commission
(CPSC) and the U.S. Environmental Protection Agency (EPA),
this product has an Average Useful Life of seven (7) years, or 270
hours of operation. At the end of the Average Useful Life, buy
a new machine or have the machine inspected annually by an
authorized service dealer to ensure that all mechanical and
safety systems are working properly and not worn excessively.
Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any
way. Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.

WARNING: Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

6 sectiOn 2 — iMpOrtant safe OperatiOn practices

SAVE THESE INSTRUCTIONS!

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (represents a 15° slope)

15°

Use this page as a guide to determine slopes where you may not operate safely.

WARNING: Do not operate your lawn mower on such slopes. Do not mow on inclines with a slope in excess of 15 degrees

(a rise of approximately 2-1/2 feet every 10 feet). A riding mower could overturn and cause serious injury. Operate riding

mowers up and down slopes, never across the face of slopes.

7sectiOn 2 — safe OperatiOn practices

Assembly & Set-Up

Assembly & Set-Up

3

3

Tractor Set-Up

NOTE: This Operators Manual covers a range of product
specifications for various models. Characteristics and features
discussed and/or illustrated in this manual may not be applicable
to all models. MTD LLC reserves the right to change product
specifications, designs and equipment without notice and
without incurring obligation.

Attaching the Battery Cables

NOTE: Some models are shipped with the battery cables already
connected.

Shipping Brace Removal

WARNING! Make sure the riding mower’s engine is

off, remove the ignition key, and set the parking
brake before removing the shipping brace. Refer to
the Controls and Features section for instructions on
how to set the parking brake.

Locate the shipping brace, if present, and accompanying

•
warning tag found on the right side of the mower, between
the discharge chute and the cutting deck. See Fig. 3-2.

Figure 3-1

NOTE: The positive battery terminal is marked Pos. (+). The
negative battery terminal is marked Neg. (–).

The positive cable (heavy red wire) is secured to the

•
positive battery terminal (+) with a hex bolt and hex nut at
the factory. Make certain that the rubber boot covers the
terminal to help protect it from corrosion.

Remove the hex bolt and hex nut from the negative cable.

•
Remove the black plastic cover, if present, from the

•
negative battery terminal and attach the negative cable
(heavy black wire) to the negative battery terminal (–) with
the bolt and nut.

NOTE: If the battery is put into service after the date shown
on top/side of battery, charge the battery as instructed in the
Service section of this manual prior to operating the tractor.

Figure 3-2

Place the deck lift lever in the highest cutting position.

•
Refer to Setting the Cutting Height in the Operation
section of this manual.

While pushing the discharge chute towards the machine

•
with your left hand, remove the shipping brace with your
right hand by grasping it between your thumb and index
finger and rotating it clockwise.

WARNING! The shipping brace, used for packaging

purposes only, must be removed and discarded
before operating your riding mower.

WARNING! The mowing deck is capable of

throwing objects. Failure to operate the riding
mower without the discharge cover in the proper
operating position could result in serious personal
injury and/or property damage.

8

8

Attaching The Steering Wheel

If the steering wheel for your tractor did not come attached, the
hardware for attaching it has been packed within the steering
wheel, beneath the steering wheel cap. Carefully pry off the
steering wheel cap and remove the hardware.

With the wheels of the tractor pointing straight forward,

1.
place the steering wheel over the steering shaft.

Place the washer (with the cupped side down) over the

2.
steering wheel and secure with the hex bolt. See Fig. 3-3.

Figure 3-3

Place the steering wheel cap over the center of the steering

3.
wheel and push downward until it “clicks” into place.

Standard Adjustment Seat

Position the shoulder screws (found on the base of the seat)

1.
inside the slot openings in the seat pivot bracket. Fig. 3-4.

Figure 3-4

Slide the seat slightly rearward in the seat pivot bracket,

2.
lining up the rear slots in the pivot bracket with the
remaining two holes in the seat’s base.

Select desired position for the seat, and secure with the

3.
two hex screws removed earlier. See Fig. 3-4.

To adjust the position of the seat, loosen the two hex

4.
screws on the bottom of the seat. Slide the seat forward or
backward as desired. Retighten the two screws.

Attaching The Seat

Seat styles vary by tractor model and there are three different
styles available:

Standard Adjustment

•
Quick Adjustment

•
Knob Adjustment

•

If the seat for your tractor was not attached at the factory, refer
to Fig. 3-4, Fig. 3-5, and Fig. 3-6 to identify your tractor’s seat
style and follow the applicable instructions below to attach it.

NOTE: For shipping reasons, seats are either fastened to the
tractor seat’s pivot bracket with a plastic tie, or mounted
backward to the pivot bracket. In either case, free the seat
from its shipping position and remove the two hex screws (or
knobs, on models so equipped) from the bottom of seat before
proceeding with applicable instructions below.

Knob Adjustment Seat

Position the shoulder screws (found on the base of the seat)

1.
inside the slot openings in the seat pivot bracket.
See Fig. 3-5.

Figure 3-5

9sectiOn 2 — asseMbly & set-up

9sectiOn 2 — asseMbly & set-up

Slide the seat slightly rearward in the seat pivot bracket,

2.
lining up the rear slots in the pivot bracket with the
remaining two holes in the seat’s base.

Select desired position for the seat, and secure with the

3.
two knobs removed earlier. See Fig. 3-5.

To adjust the position of the seat on models so equipped,

4.
loosen the two knobs on the bottom of the seat. Slide the
seat forward or backward as desired. Retighten the two
knobs.

Quick Adjustment Seat

NOTE: If your seat was shipped mounted backwards on the seat
pivot bracket, pull out the tab found on the seat stop and hold it
open while sliding the seat off the seat pivot bracket. See Fig. 3-6.

Line up the plastic seat spacers with the slots in seat pivot

1.
bracket.

Slide seat in until front seat spacer engages the seat stop.

2.
See Fig. 3-6.

To adjust the position of the seat on models equipped with

4.
a seat adjustment lever, move the seat adjustment lever
(located under the seat) to the left and slide the seat forward
or rearward. See Fig. 3-7. Make sure seat is locked into
position before operating the tractor.

Figure 3-7

Figure 3-6

WARNING! Before operating this machine, make

sure the seat is engaged in the seat stop, stand
behind the machine and pull back on seat until fully
engaged into stop.

Mulch Plug (if equipped)

On tractor models so equipped, a mulch plug can be found
within the cutting deck’s discharge opening.

NOTE: Refer to Mulching in the “Operation” section of this
manual for more detailed information.

If you’d prefer to operate the cutting deck without mulching,
simply remove the mulch plug by unthreading the plastic
wing nut which fastens it to the cutting deck. This will allow
the clippings to discharge out of the discharge opening during
operation. See Fig. 3-8.

10 sectiOn 2— asseMbly & set-up

10 sectiOn 2— asseMbly & set-up

Figure 3-8

Tire Pressure

WARNING! Maximum tire pressure under any

circumstances is 30 psi. Equal tire pressure should be
maintained at all times. Never exceed the maximum
inflation pressure shown on the sidewall of the tire.

The recommended operating tire pressure is:

Approximately 10 psi for the rear tires

•
Approximately 14 psi for the front tires

•

IMPORTANT: Refer to the tire sidewall for exact tire

manufacturer’s recommended or maximum psi. Do not
overinflate. Uneven tire pressure could cause the cutting deck to
mow unevenly.

Gas and Oil Fill-up

The gasoline tank is located under the hood and has a capacity
of 1-½ gallons. Do not overfill.

WARNING! Use extreme care when handling

gasoline. Gasoline is extremely flammable and the
vapors are explosive. Never fuel machine indoors or
while the engine is hot or running. Extinguish
cigarettes, cigars, pipes, and other sources of ignition.

Service the engine with gasoline and oil as instructed in the
separate Engine Operator/Owner Manual packed with your
tractor. Read instructions carefully.

IMPORTANT: Your tractor is shipped with motor oil in the
engine. However, you MUST check the oil level before
operating. Be careful not to overfill.

Setting the Deck Gauge Wheels (if so equipped)

Move the tractor on a firm and level surface, preferably
pavement, and proceed as follows

Select the height position of the cutting deck by placing

1.
the deck lift lever in the normally desired mowing height
setting (any of the six different cutting height notches on the
right fender).

Check the gauge wheels for contact or excessive clearance

2.
with the surface below. The deck gauge wheels should
have between ¼-inch and ½-inch clearance above the
ground as follows:

If the gauge wheels have excessive clearance or contact with the
surface, adjust as follows:

Raise the deck lift handle to its highest setting.

a.

Remove the gauge wheels by removing the lock

b.

nuts and shoulder screws which secure them to the
deck. See Fig. 3-9

Figure 3-9

Place the deck lift lever in the desired mowing

c.

height setting.
Reinsert the shoulder screw (with each gauge

d.

wheel) into the index hole that leaves approximately
½-inch between the bottom of the wheel and the
pavement.

Refer to Leveling the Deck in the Maintenance section of this
manual for more detailed instructions regarding various deck
adjustments.

11sectiOn 2 — asseMbly & set-up

11sectiOn 2 — asseMbly & set-up

Controls and Features

Speed Control &

Parking Brake Lever

Clutch/Brake Pedal

4

Choke Knob

(On some models)

Shift Lever

Lawn Tractor controls and features are illustrated in Fig 4-1 and described on the following pages.

WARNING! Read and follow all safety rules and instructions in this manual, including the entire Operation section,

before attempting to operate this machine. Failure to comply with all safety rules and instructions may result in personal
injury.

Ignition Switch

Module

PTO (Blade Engage) Lever

Figure 4-1

Throttle/Choke Lever

Deck Lift Lever

12

Throttle Control Lever

FAST

SLOW

CHOKE

FAST

SLOW

Off

On/Lights

Start

Off

On/Lights

Start

On

Stop

Position

Normal

Mowing

Start

Position

Reverse

Caution Mode

A

B

C

The throttle control lever is located on the right side of the
tractor’s dash panel. This lever controls the speed of the engine
and, on some models, when pushed all the way forward, the
choke control also. When set in a given position, the throttle will
maintain a uniform engine speed. See Fig. 4-2.

IMPORTANT: When operating the tractor with the cutting deck

engaged, be certain that the throttle lever is always in the FAST
(rabbit) position.

Choke Control

On some models, moving the throttle
lever all the way forward activates the
engine’s choke control. On all other
models, the choke control can be found
on the left side of the dash panel and is
activated by pulling the knob outward.
Activating the choke control closes the
choke plate on the carburetor and aids in
starting the engine. Refer to Starting The
Engine in the Operation section of this
manual for detailed starting instructions.

Ignition Switch

Your new lawn tractor will have one of the following ignition
switches. Use Fig. 4-3 to identify which switch your machine
utilizes and follow these instructions for proper operation.

3-Position Ignition Switch

The ignition switch is activated to start the engine. Insert key
into the ignition switch and turn clockwise to the START position.
Release the key into the ON position once engine has fired. See
Fig. 4-3A. The engine will run with the headlights on.

To stop the engine, turn the ignition key counterclockwise to the
OFF position. See Fig. 4-3A.

Figure 4-2

Figure 4-3

4-Position Ignition Switch

The ignition switch is activated to start the engine. Insert key
into the ignition switch and turn clockwise to the START position.
Release the key into the ON position once engine has fired.
See Fig. 4-3B. The engine will run with the headlights off in
this position. To activate the headlights, turn the key one more
position to the left. The engine will continue to run with the
headlights on.

13sectiOn 4 — cOntrOls and features

To stop the engine, turn the ignition key counterclockwise to the
OFF position. See Fig. 4-3B.

Ignition Switch Module

To start the engine, insert the key into the ignition switch and
turn clockwise to the START position. Release the key into the
NORMAL MOWING MODE position once the engine has fired. The
headlights will be activated in the Normal (and Reverse Caution
Modes).

To stop the engine, turn the ignition key counterclockwise to the
OFF position. See Fig. 4-3C.

WARNING! Never leave a running machine

unattended. Always disengage PTO, move shift lever
into neutral position, set parking brake, stop engine
and remove key to prevent unintended starting.

IMPORTANT: Prior to operating the tractor, refer to both Safety

Interlock Switches and Starting The Engine in the Operation
section of this manual for detailed instructions regarding the
Ignition Switch Module and operating the tractor in REVERSE
CAUTION MODE.

Clutch-Brake Pedal

The clutch-brake pedal is located on the left side of the lawn
tractor, along the running board. Depress the clutch-brake pedal
part way down when slowing the tractor by changing speeds
(Refer to Speed Control Lever). Depress the pedal all the way down
to engage the disc brake and bring the tractor to a complete
stop.

NOTE: The pedal must be depressed to start the engine. Refer to
Safety Interlock Switches in the Operation section of this manual.

Parking Brake

To set the parking brake, fully depress the clutch-brake pedal.
Move the speed control lever all the way down and into the
parking brake position. Release the clutch-brake pedal to allow
the parking brake to engage.

To release the parking brake, depress the clutch-brake pedal and
move the speed control lever out of the notches to the desired
position. Release the speed control lever and the clutch-brake
pedal.

NOTE: The parking brake must be set if the operator leaves the
seat with the engine running or the engine will automatically
shut off.

Shift Lever

The shift lever is located on the left side of the fender and has
three positions, FORWARD, NEUTRAL and REVERSE. The brake
pedal must be depressed and the tractor must not be in motion
when the moving shift lever. See Fig. 4-4.

IMPORTANT: Never force the shift lever. Doing so may result in

serious damage to the tractor’s transmission.

Figure 4-4

Speed Control Lever

The speed control lever, located on the left side of
the tractor’s dash console, allows you to regulate
the ground speed of the lawn tractor. To use,
depress the clutch-brake pedal and move the lever
out of the parking brake notch and forward to
increase the tractor’s ground speed. When a desired
speed has been reached, release the lever into an
appropriate notch to maintain that speed.

To slow the tractor’s ground speed, depress the
clutch-brake pedal and move the speed control
lever rearward and release it into a notch.

NOTE: Lawn tractors vary by model and are
available with either a 6- or 7-speed control lever.

PTO (Blade Engage) Lever

Found on the tractor’s right fender, the PTO (blade
engage) lever is used to engage power to the cutting

deck or other (separately available) attachments.
To operate, move the lever all the way forward.
Moving the lever all the way rearward into the PTO
OFF position disengages power to the cutting deck/
attachment.

NOTE: The PTO (blade engage) lever must be in the
disengaged (PTO OFF) position when starting the
engine.

Deck Lift Lever

Found on your tractor’s right fender, the deck lift lever
is used to change the height of the cutting deck. To
use, move the lever to the left, then place in the notch
best suited for your application.

14 sectiOn 4 — cOntrOls and features

Operation

Stop
position

Start
position

Indicator
Light

Reverse
Push
Button

Normal
Driving
Mode

Reverse
Caution
Mode
Position

Operation

5

5

Models with Reverse Caution Mode

With the ignition key in the NORMAL MOWING position,

•
the engine will automatically shut off if the PTO (Blade
Engage) lever is moved into the engaged (ON) position with
the shift lever in Reverse.

WARNING! Do not operate the tractor if the

interlock system is malfunctioning. This system was
designed for your safety and protection.

Reverse Caution Mode

(Models equipped with ignition switch module)

WARNING! Use extreme caution while operating

the tractor in the REVERSE CAUTION MODE. Always
look down and behind before and while backing.
Do not operate the tractor when children or others
are around. Stop the tractor immediately if someone
enters the area.

The REVERSE CAUTION MODE position of the key switch
module allows the tractor to be operated in reverse with the
blades (PTO) engaged.

IMPORTANT: Mowing in reverse is not recommended.

Safety Interlock Switches

This tractor is equipped with a safety interlock system for the
protection of the operator. If the interlock system should ever
malfunction, do not operate the tractor. Contact an authorized
MTD service dealer.

The safety interlock system prevents the engine from

•
cranking or starting unless the parking brake is engaged,
and the PTO (Blade Engage) lever is in the disengaged (OFF)
position.

The engine will automatically shut off if the operator leaves

•
the seat before engaging the parking brake.

The engine will automatically shut off if the operator leaves

•
the tractor’s seat with the PTO (Blade Engage) lever in the
engaged (ON) position, regardless of whether the parking
brake is engaged.

The engine will automatically shut off if the operator

•
engages the PTO with the parking brake ON.

Models without Reverse Caution Mode

The engine will automatically shut off if the PTO (Blade

•
Engage) lever is moved into the engaged (ON) position with
the shift lever in Reverse.

To use the REVERSE CAUTION MODE:

IMPORTANT: The operator MUST be seated in the tractor seat.

Start the engine as instructed in the Operation section of

1.
this manual.

Turn the key from the NORMAL MOWING (Green) position

2.
to the REVERSE CAUTION MODE (Yellow) position of the key
switch module. See Fig. 5-1.

Depress the REVERSE PUSH BUTTON (Orange, Triangular

3.
Button) at the top, right corner of the key switch module.
The red indicator light at the top, left corner of the key
switch module will be ON while activated. See Fig. 5-1.

Figure 5-1

15

15

Once activated (indicator light ON), the tractor can be

4.
driven in reverse with the cutting blades (PTO) engaged.

Always look down and behind before and while backing to

5.
make sure no children are around.

After resuming forward motion, return the key to the

6.
NORMAL MOWING position.

IMPORTANT: The REVERSE CAUTION MODE will remain

activated until:

The key is placed in either the NORMAL MOWING

a.

position or STOP position.
The operator engages the parking brake by fully

b.

depressing the clutch-brake pedal and holding it
down while moving the speed control lever into the
PARK BRAKE position.

Engaging the Parking Brake

To engage the parking brake:

Fully depress the clutch-brake pedal and hold it down with

1.
your foot.

Move the speed control lever all the way down and into the

2.
parking brake position.

Release the clutch-brake pedal to allow the parking brake

3.
to engage.

To release the parking brake:

Depress the clutch-brake pedal and move the speed

1.
control lever out of the parking brake position and into a
desired speed.

Setting the Cutting Height

Select the height position of the cutting deck by placing

1.
the deck lift lever in any of the six different cutting height
notches on the right side of the fender.

Adjust the deck wheels as instructed in the Assembly & Set-

2.
Up section earlier in this manual, if equipped, so that they
are between ¼-inch and ½-inch above the ground when
the tractor is on a smooth, flat surface such as a driveway.

WARNING! Keep hands and feet away from the

discharge opening of the cutting deck.

Starting the Engine

WARNING! Do not operate the tractor if the

interlock system is malfunctioning. This system was
designed for your safety and protection.

NOTE: Refer to the Gasoline and Oil fill-up instructions in the
Assembly & Set-up section of this manual.

Insert the tractor key into the ignition switch.

1.
Place the PTO (Blade Engage) lever in the disengaged (OFF)

2.
position.

Engage the tractor’s parking brake.

3.
Activate the choke control.

4.
Turn the ignition key clockwise to the START position. After

5.
the engine starts, release the key. It will return to the ON (or
Normal Mowing) position.

CAUTION: Do NOT hold the key in the START

position for longer than ten seconds at a time.
Doing so may cause damage to your engine’s
electric starter.

After the engine starts, deactivate the choke control and

6.
place the throttle control in the FAST position.

NOTE: Do NOT leave the choke control on while operating the
tractor. Doing so will result in a “rich” fuel mixture and cause the
engine to run poorly.

Stopping the Engine

WARNING! If you strike a foreign object, stop the

engine, disconnect the spark plug wire(s) and
ground against the engine. Thoroughly inspect the
machine for any damage. Repair the damage before
restarting and operating

If the blades are engaged, place the PTO (Blade Engage)

1.
lever in the disengaged (OFF) position.

Turn the ignition key counterclockwise to the STOP

2.
position.

Remove the key from the ignition switch to prevent

3.
unintended starting.

NOTE: On models so equipped, the deck wheels are an anti-scalp
feature of the deck and are not designed to support the weight
of the cutting deck. Refer to Leveling in the Maintenance section
of this manual for more detailed instructions regarding various
deck adjustments.

16 sectiOn 5— OperatiOn

16 sectiOn 5— OperatiOn

Driving The Tractor

WARNING! Avoid sudden starts, excessive speed

and sudden stops.

WARNING! Do not leave the seat of the tractor

without first placing the PTO (Blade Engage) lever in
the disengaged (OFF) position, depressing the brake
pedal and engaging the parking brake. If leaving
the tractor unattended, also turn the ignition key off
and remove the key.

WARNING! Always look down and behind before

and while backing up to avoid a back-over accident.

Depress the brake pedal to release the parking brake and

1.
let the pedal up.

Move the throttle lever into the FAST (rabbit) position.

2.
Place the shift lever in either the FORWARD or REVERSE

3.
position.

IMPORTANT: Do NOT use the shift lever to change the

direction of travel when the tractor is in motion. Always use
the brake pedal to bring the tractor to a complete stop before
shifting.

Release the parking brake by depressing the clutch-brake

4.
pedal and positioning the speed control lever in desired
position.

IMPORTANT: First-time operators should use speed positions 1

or 2. Become completely familiar with the tractor’s operation and
controls before operating the tractor in higher speed positions.

Release clutch-brake pedal slowly to put unit into motion.

5.
The lawn tractor is brought to a stop by depressing the

6.
clutch-brake pedal.

NOTE: When operating the unit initially, there will be little
difference between the highest two speeds until after the belts
have seated themselves into the pulleys during the break-in
period.

WARNING! Before leaving the operator’s position

for any reason, disengage the blades, place the shift
lever in neutral, engage the parking brake, shut
engine off and remove the key.

IMPORTANT: When stopping the tractor for any reason while

on a grass surface, always:

Place the shift lever in neutral,

1.
Engage the parking brake,

2.
Shut engine off and remove the key. Doing so will minimize

3.
the possibility of having your lawn ‘‘browned’’ by hot
exhaust from your tractor’s running engine.

If unit stalls with speed control in high speed, or if unit will
not operate with speed control lever in a low speed position,
proceed as follows:

Place shift lever in NEUTRAL.

1.
Restart engine.

2.
Place speed control lever in highest speed position.

3.
Release clutch-brake pedal fully.

4.
Depress clutch-brake pedal.

5.

Place speed control lever in desired position.

6.
Place shift lever in either FORWARD or REVERSE, and follow

7.
normal operating procedures.

Driving On Slopes

Refer to the SLOPE GAUGE in the Important Safe Operation
Practices section of the manual to help determine slopes where
you may operate the tractor safely.

WARNING! Do not mow on inclines with a slope in

excess of 15 degrees (a rise of approximately 2-1/2 feet
every 10 feet). The tractor could overturn and cause

serious injury.

Mow up and down slopes, NEVER across.

•
Exercise extreme caution when changing direction on

•
slopes.

Watch for holes, ruts, bumps, rocks, or other hidden

•
objects. Uneven terrain could overturn the machine. Tall
grass can hide obstacles.

Avoid turns when driving on a slope. If a turn must be

•
made, turn down the slope. Turning up a slope greatly
increases the chance of a roll over.

Avoid stopping when driving up a slope. If it is necessary

•
to stop while driving up a slope, start up smoothly and
carefully to reduce the possibility of flipping the tractor
over backward.

Engaging the Blades

Engaging the PTO (Blade Engage) transfers power to the cutting
deck or other (separately available) attachments. To engage the
blades, proceed as follows:

Move the throttle control lever to the FAST (rabbit)

1.
position.

Grasp the PTO (Blade Engage) lever and pivot it all the way

2.
forward into the engaged (ON) position.

Keep the throttle lever in the FAST (rabbit) position for the

3.
most efficient use of the cutting deck or other (separately
available) attachments.

NOTE: Models with Reverse Caution Mode: The engine will
automatically shut off if the PTO is engaged with the shift lever
in position for reverse travel with the ignition key in the NORMAL
MOWING position.

Models without Reverse Caution Mode:

The PTO (Blade Engage) lever must be in the disengaged (OFF)
position when starting the engine, when traveling in reverse, and
if the operator leaves the seat. Refer to Safety Interlock Switches
in the Operation section of this manual.

Using the Deck Lift Lever

To raise the cutting deck, move the deck lift lever to the left, then
place it in the notch best suited for your application. Refer to
Setting The Cutting Height earlier in this section.

17sectiOn 5 — Oper atiOn

17sectiOn 5 — Oper atiOn

Mowing

WARNING! To help avoid blade contact or a

thrown object injury, keep bystanders, helpers,
children and pets at least 75 feet from the machine
while it is in operation. Stop machine if anyone
enters the area.

The following information will be helpful when using the cutting
deck with your tractor:

WARNING! Plan your mowing pattern to avoid

discharge of materials toward roads, sidewalks,
bystanders and the like. Also, avoid discharging
material against a wall or obstruction which may
cause discharged material to ricochet back toward
the operator.

Do not mow at high ground speed, especially if a mulch kit

•
or grass collector is installed.

For best results it is recommended that the first two laps be

•
cut with the discharge thrown towards the center. After the
first two laps, reverse the direction to throw the discharge
to the outside for the balance of cutting. This will give a
better appearance to the lawn.

Do not cut the grass too short. Short grass invites weed

•
growth and yellows quickly in dry weather.

Mowing should always be done with the engine at full throttle.

•
Under heavier conditions it may be necessary to go back

•
over the cut area a second time to get a clean cut.

Do NOT attempt to mow heavy brush and weeds and

•
extremely tall grass. Your tractor is designed to mow lawns,
NOT clear brush.

Keep the blades sharp and replace the blades when

•
worn. Refer to Cutting Blades in the Service section of this
manual for proper blade sharpening instructions.

Mulching

Select models come equipped with a mulch kit which
incorporates special blades, already standard on the tractor, in a
process of recirculating grass clippings repeatedly beneath the
cutting deck. The ultra-fine clippings are then forced back into
the lawn where they act as a natural fertilizer.

Observe the following points for the best results when mulching:

Never attempt to mulch if the lawn is damp. Wet grass

•
tends to stick to the underside of the cutting deck
preventing proper mulching of the clippings.

Do NOT attempt to mulch more than 1/3 the total height of

•
the grass or approximately 1-1/2 inches. Doing so will cause
the clippings to clump up beneath the deck and not be
mulched effectively.

Maintain a slow ground speed to allow the grass clippings

•
more time to effectively be mulched.

Always position the throttle control lever in the FAST

•
(rabbit) position and allow it to remain there while
mowing. Failing to keep the engine at full throttle places
strain on the tractor’s engine and does not allow the
blades to properly mulch grass. Ground speed should be
controlled using the speed control lever.

NOTE: It is not necessary to remove the discharge chute to
operate the mower with the mulch kit installed.

WARNING! Never operate the mower without the

discharge chute properly attached.

To operate the cutting deck without mulching, simply remove
the mulch plug by unthreading the plastic wing nut which
fastens it to the cutting deck. This will allow the clippings to
discharge out the side. See Fig. 5-2.

Figure 5-2

Headlights

On some models, the lamps are ON whenever the tractor’s

•
engine is running. On other models, the lamps are ON
whenever the ignition key is moved into the lights position,
with the engine running.

On all models, the lamps turn OFF when the ignition key is

•
moved to the STOP position.

18 sectiOn 5— OperatiOn

18 sectiOn 5— OperatiOn

Maintenance & Adjustments

6

Maintenance

WARNING! Before performing any maintenance or

repairs, disengage PTO, move shift lever into neutral
position, set parking brake, stop engine and remove
key to prevent unintended starting.

Engine

Refer to the Engine Operator/Owner Manual for engine
maintenance instructions.

Check engine oil level before each use as instructed in the
Engine Operator/Owner Manual packed with your unit. Follow
the instructions carefully.

Changing Engine Oil

For draining oil from the engine’s crankcase of select model
tractors, a plastic oil drain sleeve is packed with this Operator’s
Manual. To drain the oil, proceed as follows:

Unscrew the oil fill cap and remove the dipstick from the oil

1.
fill tube.

Snap the small end of oil drain sleeve onto the oil sump.

2.
See Fig. 6-1.

NOTE: Refer to the Engine Operator/Owner Manual packed with
your unit for information regarding the quantity and proper
viscosity of motor oil.

Air Cleaner

Service the pre-cleaner, if so equipped, and cartridge/air cleaner
element as instructed in the Engine Operator/Owner Manual
packed with your unit.

Spark Plug

The spark plug should be cleaned and the gap reset once a
season. Spark plug replacement is recommended at the start
of each mowing season. Refer to the Engine Operator/Owner
Manual for correct plug type and gap specifications.

Lubrication

WARNING! Before lubricating, repairing, or

inspecting, always disengage PTO, move shift lever
into neutral position, set parking brake, stop engine
and remove key to prevent unintended starting.

Engine

Lubricate the engine with motor oil as instructed in the Engine
Owner Manual packed with your unit.

Pivot Points & Linkage

Lubricate all the pivot points on the drive system, parking brake
and lift linkage at least once a season with light oil.

Figure 6-1

Remove drain plug and drain oil into a suitable container

3.
with a capacity of no less than 64 oz.

Service oil filter (if so equipped) as instructed in the separate

4.
Engine Operator/Owner Manual packed with your unit.

Perform the above steps in the opposite order after oil has
finished draining.

Refill the engine with new motor oil as instructed in

5.
the Engine Operator/Owner Manual packed with your
machine.

Rear Wheels

The rear wheels should be removed from the axles once a
season. Lubricate the axles and the rims well with an all-purpose
grease before re-installing them.

Front Axles

Each end of the tractor’s front pivot bar may be equipped with a
grease fitting. Lubricate with a grease gun after every 25 hours of
tractor operation.

Battery

The battery is sealed and is maintenance-free. Acid levels cannot
be checked.

Always keep the battery cables and terminals clean and

•
free of corrosive build-up.

After cleaning the battery and terminals, apply a light coat

•
of petroleum jelly or grease to both terminals.

Always keep the rubber boot positioned over the positive

•
terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason,

disconnect the NEGATIVE (Black) wire from it’s terminal first,
followed by the POSITIVE (Red) wire. When re-installing the
battery, always connect the POSITIVE (Red) wire its terminal
first, followed by the NEGATIVE (Black) wire. Be certain that the
wires are connected to the correct terminals; reversing them
could change the polarity and result in damage to your engine’s
alternating system.

19

Cleaning Battery

Hex Plug

Clean the battery by removing it from the tractor and washing
with a baking soda and water solution. If necessary, scrape the
battery terminals with a wire brush to remove deposits. Coat
terminals and exposed wiring with grease or petroleum jelly to
prevent corrosion.

Battery Failures

Some common causes for battery failure are:

Incorrect initial activation

•
Overcharging

•
Freezing

•
Undercharging

•
Corroded connections

•

These failures are NOT covered by your tractor’s warranty.

Cleaning the Engine And Deck

Any fuel or oil spilled on the machine should be wiped off
promptly. Do NOT allow debris to accumulate around the cooling
fins of the engine or on any other part of the machine.

IMPORTANT: The use of a pressure washer to clean your

tractor is NOT recommended. It may cause damage to electrical
components, spindles, pulleys, bearings or the engine.

A hex plug can be found on your tractor’s deck surface. See Fig. 6-2.

Deck Wash System™

If your tractor’s deck is equipped with a water port on its surface
as part of its Deck Wash System™, follow these instructions to
utilize this feature.

Use the Deck Wash System™ to rinse grass clippings from the
deck’s underside and prevent the buildup of corrosive chemicals.
Complete the following steps AFTER EACH MOWING:

Drive the tractor to a level, clear spot on your lawn, near

1.
enough for your garden hose to reach.

CAUTION: Make certain the tractor’s discharge

chute is directed AWAY from your house, garage,
parked cars, etc.

Disengage the PTO (Blade Engage), set the parking brake

2.
and stop the engine.

Thread the hose coupler (packaged with your tractor’s

3.
Operator’s Manual) onto the end of your garden hose.

Attach the hose coupler to the water port on the deck’s

4.
surface. See Fig. 6-3.

Figure 6-2

This plug can be replaced with a water port to be used as part of
a separately-available deck wash system.

The Deck Wash System™ is used to rinse grass clippings from the
deck’s underside and prevent the buildup of corrosive chemicals.

NOTE: Refer to the Attachments & Accessories section of this
manual for information regarding this and other separately­available attachments & accessories for your tractor.

20 sectiOn 6— Maintenance & adjustMents

Figure 6-3

Turn the water on.

5.
While sitting in the operator’s position on the tractor, start

6.
the engine and place the throttle lever in the FAST (rabbit)
position.

Move the tractor’s PTO (Blade Engage) into the ON position.

7.
Remain in the operator’s position with the cutting deck

8.
engaged for a minimum of two minutes, allowing the
underside of the cutting deck to thoroughly rinse.

Move the tractor’s PTO (Blade Engage) into the OFF

9.
position.

Turn the ignition key to the STOP position to turn the

10.
tractor’s engine off.

Turn the water off and detach the hose coupler from the

11.
water port on your deck’s surface.

On 46” decks, repeat steps 4 through 11 on the opposite

12.
side of the cutting deck.